HELP !
I just upgraded my I-mate JAM to the Shipped 1.12.550 ROM from the FTP and all went well.
Afterwards I wanted to do the radio update to 1.13 but this one failed miserably leaving the device at the bootloader screen (USB v1.02).
I then disconnected and tried again to no avail .. Next steps were soft reset/hard reset/remove battery etc ... levaing me in the end with the phone being dead, only giving a tick when I trie to turn it on or to hard reset it ...
Now it is laying there with the battry removed as to discharche the backup battery.
Is there anything else I can do ?
I just hope it isn't dead !
Please Help
fixed ... I had to reset into the bootloader (camera/power + reset) and reflash from scratch
Try to download different version of ROM, Then try to install again from begining.
Related
Hi there,
I bought a Qtek S200 and I tried to do a ROM upgrade. I followed the instructions given in the website http://kimpeacocke.blogspot.com/2006/06/how-to-perform-rom-upgrade-on-your-i.html
I got the upgrade from this site at ftp://xda:[email protected]_022021_Dopod_PDAMobizEdition_v101.zip
I followed the procedure given in the website given above. After I upgraded successfully the phone has become locked in the boot loader screen. I have done both soft reset and hard reset. Nothing works. The phone gets locked in the boot loader screen. Need help.
Thanks,
Julian
Try to reflash with Qtek ROM instead...
Why you said that it's locked on the Bootloader screen?
Is it frozen or locked?
Hi Rayan,
I tried flashing with the Qtek ROM. I cannot active sync as it does not connect to the device. So I cannot flash. As soon as I powerup, I get the Qtek screen and then it goes to the bootloader screen and stays there. Nothing else happens. I have sent the device back to the guy from whom I bought it.
I got the same problem as Julian - I tried to upgrade with the mentioned ROM and now my device are stucked at the boot screen :?
Some help here ? I'm in same situation
I have an O2 with Dopod rom, after I instaled some software I must to restart and then my O2 are stucked/frozen on Windows Mobile splash screen
Only if I remove the battery I can stop the pda.
I can't do nothing to make him to start. Some ideea ?
:shock:
Later Edit :
solved with http://forum.xda-developers.com/viewtopic.php?t=49298&sid=35f5c1e9e165997b4634ea0c7700ac76
Same issue here with a O2 Xda Neo with German Rom.
Applied the procedure of the prophet wiki : How to CID unlock and Upgrade your Prophet (SPL 2.09 & 2.15)
After step 6 and a soft rest it is stuck in bootloader and will not do anything else, not even off or hard reset...battey has to be removed in order to shut it off....
Any ideas?
Remind me to find the guy who wrote the wiki page on unlocking CID in Prophet......good job pal......
Aaaaarggghhhh %^*^%*^%*^%*
Problem solved..
Hi everyone,
Good news at last. I sent my Qtek S200 to the guy from whom I bought the phone. He fixed it and now I am a happy man. You can check with him if everything else fails. Email him at E gadget Depot ( [email protected]).
All the best..
i tried to upgrade my QTEK S200 with this RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID.zip it got to 95% and then it gives me nbf file cannot work with your PDA. Please help.
I have this problem too, i know only one exit from this situation - i have flash my s200 with RUU_215737_2157135_023021_QTEK_s200_RUS ROM, now it work fine.
you find it her
bootloader issue
I have the same problem too, If anybody know method to fix this problem please help us.
I cannot active sync as it does not connect to the device. So I cannot flash. As soon as I powerup, I get the Qtek screen and then it goes to the bootloader screen and stays there.
THX in advance for you help
Robert
have same prob but solved thanx to this post
http://forum.xda-developers.com/viewtopic.php?t=58892&highlight=boot
and remember First off all, to enter in Boot Loader Mode is:
Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.
Then upgrade using a ROM
Please, the links to the solution does not exists anymore.
I need help!!
Qtek S200 stuck in tri-color screen, all flashing so far still does not make it work..
When doing a hard reset I get format failed.
/Jonas
I have same problem!
Anyone can help?
TJSM said:
I have same problem!
Anyone can help?
Click to expand...
Click to collapse
Go to HMA4's upgrade guide or my thread in my signature...
same problem
i have exactly same problem and i couldnt solve it too.So can someone help us?
Please someone explain completely what should we do.
i can not active sync and waiting on the bootloader screen
bacardilima said:
have same prob but solved thanx to this post
http://forum.xda-developers.com/viewtopic.php?t=58892&highlight=boot
and remember First off all, to enter in Boot Loader Mode is:
Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.
Then upgrade using a ROM
Click to expand...
Click to collapse
daelee,
you can get normal state, follow the bolded attention at above quote.after entering the 3 colour screen connect USB and you can load the original WM5 ROM on your device. after that, upgrade to any wm6 by the rules and active sync.
the link is dead on that message..
i went to the that page and the link for solution is dead.
http://forum.xda-developers.com/showthread.php?t=376561
find out is there anything that can help!
when i flashing my dopod , my house suddenly blackout.
So what happened to my dopod is that i stuck at IPL, SPL , GMS , OS page, and it didnt load windows anymore.
I tried to hard reset it , but it helpless
I can go in bootloader.
Is their any possible way to install a fresh rom into it?
Searched around , but found nothing. Pls help up
try this
1) hold your communication button and soft reset *keep holding comm-button until see the RGB color bar,
2) plug-in your USB cable, u will see a 'USB' appear at your bottom left,
3) install the flash ROM from your window.
well I tried install WM6 once fail, so I do the above step, and 2nd time successfully upgrade to WM6, you can use back your original ROM download form dopod site.
goodluck
feiyee said:
when i flashing my dopod , my house suddenly blackout.
So what happened to my dopod is that i stuck at IPL, SPL , GMS , OS page, and it didnt load windows anymore.
I tried to hard reset it , but it helpless
I can go in bootloader.
Is their any possible way to install a fresh rom into it?
Searched around , but found nothing. Pls help up
Click to expand...
Click to collapse
It's easy, mail your dopd to me.
I stated to update ROM but unfortunately unplugged the cable with mistake.
Now my JAM is showing only black Screen with Text USB V1.02 . What i should do now, After rebooting many time, nothing happend, same screen.
Please help
You need to flash it again:
- fully charge your magician ( remove battery cover and plug in the charger )
- after you start your magician in bootloader ( You press power button + camera, and hit reset with stylus )
- download the rom u want ( magician wiki has loads of them and dont forget to disable USB Connections on Active Sync )
- and use matupgradenoid if you have country id error.
Rom Update Problem
Hi,
Thanks for Writing me.
I repeated all the step you sent me.
I rebooted the device and it shows USB Boot Sceen.
I downloaded ROM from clubimate.com and tried to install.
but its not working. its says unable to connect device.
Attached is the error screenshot. Please help
Hmm, can u fully upgrade your rom ?
Hi
I have the same problem.
When i try to load the rom, the device "boot" and stay in blank screen!
I tried what was sugested, bu t with no luck!
I ideias,
Thanks
Nuno Cancelo
I had a similar problem. I tried to flash the ext ROM with NZ Vodaphone and it didn't finish. The Phone would boot then hard reset. I tried to reflash with the ROM file from PC but it keep failing. Luckily I have a spare Jam. I dump the ROM of the old phone and reflashed it to the broken one. To dump the ROM of a good Imate Jam goto http://forum.xda-developers.com/showthread.php?t=230151
Once you have done this, Reboot your phone into the ROM flash menu with the SDCARD that you used from the good phone into yours.
I think from there it sees the ROM files and gives you options to reflash.
Good luck.
wiuh,my services i-mate jam dead after upgrading.
i got in bootloader mode n upgrade radio rom to 1.12 use this rom NL_11300_131_11200.exe.
i deleted nk.nbf, and ms_.nbf, so just radio.nbf
upgrade success!
then i try to upgrade with the same rom(NL_11300_131_11200.exe) without radio.nbf. fail it say error id country.ok then i try the other rom.
JAM_WWE_11200_128_11210_ship.exe
i deleted just radio.nbf,because i just want to upgrade the rom.
at ext rom upgrade it success.but when maybe about 30% uprade rom,it fail. and say error.i forgot the error.
and my i-mate dead. :'(
if i put usb cable n open the back case(baterai still in side or not) the lamp red is on.
but when i closed the back case.it turned off.
nothing happen,no indicated the pda was still connected.activesync has no sound.usb on device manager didnt indicated there was a pda connection.
so??
what must i do now?
??? this is not mine.if mine i dont care too much,but this my costumers!
anyone can help pls!
i beg u.pls!
which model u r using, i have i-mate JAMA 101.
can u tell me how u enter to bootmode?
Sree...
sreejithachuthan said:
which model u r using, i have i-mate JAMA 101.
can u tell me how u enter to bootmode?
Sree...
Click to expand...
Click to collapse
same as u did.
"please help me, i have my i-mate JAMA 101, i need to install new OS.
but cant enter its boot load. i tried camera + power + reset button this also not working...pls help me."
did that your buttons work?
i mean u have checked the button 1 by 1.(camera it self,power,then reset button?)
did that still work?
if not make it sure.dissambler it.check all the button.i can say all of the models of all pda are the same way to hard reset (as long as i know)
i have flashed many of them.
learnig said:
wiuh,my services i-mate jam dead after upgrading.
i got in bootloader mode n upgrade radio rom to 1.12 use this rom NL_11300_131_11200.exe.
i deleted nk.nbf, and ms_.nbf, so just radio.nbf
upgrade success!
then i try to upgrade with the same rom(NL_11300_131_11200.exe) without radio.nbf. fail it say error id country.ok then i try the other rom.
JAM_WWE_11200_128_11210_ship.exe
i deleted just radio.nbf,because i just want to upgrade the rom.
at ext rom upgrade it success.but when maybe about 30% uprade rom,it fail. and say error.i forgot the error.
and my i-mate dead. :'(
if i put usb cable n open the back case(baterai still in side or not) the lamp red is on.
but when i closed the back case.it turned off.
nothing happen,no indicated the pda was still connected.activesync has no sound.usb on device manager didnt indicated there was a pda connection.
so??
what must i do now?
??? this is not mine.if mine i dont care too much,but this my costumers!
anyone can help pls!
i beg u.pls!
Click to expand...
Click to collapse
the problem has been solved.i flash it many times so the batterai was too low.in brick condition, batterai cant be charged.so i changed it with other batterai.its ok now.thx for the rom.
Hi there
this happened while upgrading htc_wwe_05 of collute.
Upgrade continued till 20% ....then i got error on pc it says please reset the device and start the upgrade again ......
Then i did it so ...but no use .it starts upgrading process after 2% it stops.
please some one help ....
I'm also not sure what needs to be done on your case..but was it fully charged before upgrading? try to remove the battery then put it back on after 30 minutes..or try flashing a different rom before flashing cotulla's rom..and be sure that the radio rom is 1.12..