Related
Ok, I have a BT200 that is working very quirkly with my i-mate. Sometimes the phone transfers the call to the headset, sometimes it doesn't. After deleting and recreating the bond, it works, but not for long. Anyone have one of these setup and working properly? Is there a trick to it?
Also, does anyone know if other headset drivers exist that may work on the i-mate that would allow you to hear all audio (not just phone) through a bluetooth earpiece?
Figured it out?
Ok, I've finally pinpointed that it works fine until I turn off the jabra headset, then when I turn it back on, I have to go through the entire thing again of re-creating the bond, etc..
Anyone know how to avoid having to recreate this everytime I turn the headset on or off?
I don't now ... but i have also jaba 200 and the MDA II is must arrive...
well please chip us informed
Thanks
DenisJ
I have the same combination and have also observed the same hassles.
It seems to work when I turn the BT headset function on the MDA off and on also. Thsi seems to result in a rebond.
Exact Steps
TBD,
If you could post the exact order of the steps you take to turn on / off the headset, I'd appreciate it. Right now, I'm doing the following:
1. Finish BT Headset Call.
2. Disable Bluetooth Headset Mode on Phone.
3. Disable Bluetooth on the phone.
4. Hold button on JABRA to turn it off.
Then, attempting to...
1. Hold button on JABRA to turn it on.
2. Enable Bluetooth on the phone (Set to "On" or "Discoverable")
3. Enable Bluetooth Headset Mode on phone.
4. Attempt to make call.
So if you could posts steps like that, i'd appreciate it. Also, do you set your bluetooth to "On" or "Discoverable"? Do you ever turn off the Bluetooth Radio completely?
Thanks,
Jon.
Yup me an all. I too have the Jabra BT200 and have the same problem. Providing you don't switch off the headset or go out of range your ok, but for instance when you leave the headset in the car and take the XDA2 with you you have to create a new bond to use it again. AHHHHHHHHH!!!
Shame cos so much else has been sorted on it.....and more. What a piece of kit!!
SOMEBODY HELP!!!
OK, so here is the sequence, which seems to work (for me).
1) I set everything up as per instruction. creating the bond between the Jabra and the MDA II.
2) Before (or after) I turn off the Jabra I disable the BT-Headset on the Today-screen.
3) Then I turn the Jabra on again and wait several seconds before enabling the BT Headset on the MDA II.
This seems to work most of the time, though the hint regarding going out of distance might explain the instabilities I have still observed. In any case, using the BT-Headset ON/Off on the Today-screen seems to resync things most of the time and get the Jabra up and running again.
Hope this helps and always open for new ideas
I have been a bit impatient after turning the BT headset on. I'll try it and let you guys know.
I may have been a bit optomistic. :roll:
Today I observed that sometimes the Headset reacts very late. Consequently you miss half of the call. Seems to be an XDA problem.
As for my XDA II with Sony Ericsson HBH-65, after creating the bond, before i turn off the BT headset, i turn off BT profile and BT on my PDA, then turn off the Headset.
If i want to turn on the headset, i activate BT on my PDA, then BT profile, the the headset. Sometimes in teh day headset seem to lose the bond and cannot use the BT to call or whatever. I tried turning on/off BT on my PDA, did not work. Turn on/off headset, it worked. So for me most of the time is my headset causing the problems
i am having the same problem with the new moto bluetooth headset although i have experienced no problemzs with the se hbh-30 bluetooth headset....i can turn off and transfer calls without any impact on teh bonding
Jabra problems
I've had similar problems on a boring old Nokia 6310 with my BT200. In the end, all I could do was find the 'automaticly reconnect' option on the Nokia. during calls, the link is allways fine, but between calls, when I guess one end or the other goes to sleep, the link will drop out, and then instantly reconnect. This happens around 2 or 3 times an hour.
Is there a 'automaticly reconnect' option on your XDA?
All the best
James
OK, I finally sacked my Jabra 200, because of its instability. What use is a headset, that doesn't repond when a call comes in? :evil:
I bought a B-Speech from B-Data yesterday and it seems to be working much better :lol: .
Nokia HS-3w headset with XDA II
Well! I am using the Nokia HS-3W Bluetooth Headset with my XDA II . I can pair up two devices and use it for only ten minutes :twisted: . After that, the headset will off(goes to sleep) . I Have to turn on the headset every ten minutes. I ask the dealer about the problem. They told me this headset work fine with Nokia's phone. They told me , there is three color on the light. Red light will flash when you turn off the headset. Green Light will flash when you turn on the headset up to ten minutes, if cann't find the phone devices , it will goes off.White light will flash, when the headset connected to the phone. When I turn on the headset, I just can see the green light only.But, if someone call me or I make a call ,the white light will flash.After the that the headset will flash the green light again for about ten minutes and goes off. Can anyone help me with this problem? Thanks!
@[email protected]
Hi, I will like to ask how your headset B-Speech is working.
It works 100%?
I have a jabra 250 with the same problems as BT200
Please let me know
Regards
JoseF
The B-Speech Headset is working OK, however it doesn't solve the problems with the Microsoft BT-stack.
Some observations, probably also applicable to the Jabra:
:?: When you go out of range with the headset, it will probably not reconnect automatically (but how do you know)
:x On an incoming call, the XDA may be very slow in activating the headset, so you might miss the call (seems to be tied into what the XDA s/w is just doing at the time
When you turn the Headset off, make sure to turn it off on the Today screen first. And when you turn them on, make sure to wait about 2 sec. after you turn the headset on before turning it on on the Today screen.
:idea: What seems to work best, is turning that Headset off and then on again on the Today screen. It usually comes back after that.
Mind you, it isn't the headset thats causing these problems. Its just that Microsoft botched the Bluetooth stack - probably the programmers had blue teeth from all the wine they were drinking!
I've found the out of range issue to be mute on my jabra 200. The only time the bond is broken is when the headset has been turned off. Or sometimes when it has been on charge.....
Strange........I use the Jabra BT 250 with the MDA II and have non of these reconnection problems. I f I turn it on and place a call (or receive) it reacts immediately.
However, I cannot use the advanced Headset Profile features of the Jabra with the MDA, but this is not the fault of the Jabra........
Could the people who are having problems and the people who are not having problems with their Jabra BT200's please post their version numbers of the Jabra BT200. You can find the version number on the boom going to the microphone. It will be 2 numbers and a letter, like 48A or something like that. I'm testing a theory that I think will help identify why some people work and some don't.
Thanks,
LouisK
Ok, the number on my Jabra Bt 250 is 44B.
I have been using a JABRA BT200 Headset with my XDAII and have always had the same problem, once the BT200 has been paired with the XDAII it works fine but once I put the headset into it's charging cradle and then remove it and try to use it again it always loses it's bond, the only way I can get it to communicate with the XDAII again is to pair it again.
I don't know whether the problem lies with the BT200 or the XDAII
Does anyone else have this problem ???
Thanks
Ian Goulding
hey ian,
it was just recently that i was able to figure out the bt-xda2 bonding; thanks to some helpful chaps in the forum. in the process; i did some research within several topics and read something which may answer your query. when the headset is back in it's cradle; i believe it's "turned off" or is put into inactive mode. the forum message i read indicated that the bonding is lost once the headset is turned off; thus you have to bond again. yes, i have had similar experiences while figuring out the bonding issue. i just keep the bt200 i have out of the cradle; when the time comes to charge it i then holster it and repeat the bonding process once it's charged. i don't think it's a problem with neither devices; it's the default setting i believe. with luck probably the xda-developer guys will come up with a bug fix for this item. which could also include using bt for other than the phone function...like mp3....hint! hint!
cheers
robson
Ian_Goulding said:
I have been using a JABRA BT200 Headset with my XDAII and have always had the same problem, once the BT200 has been paired with the XDAII it works fine but once I put the headset into it's charging cradle and then remove it and try to use it again it always loses it's bond, the only way I can get it to communicate with the XDAII again is to pair it again.
I don't know whether the problem lies with the BT200 or the XDAII
Does anyone else have this problem ???
Thanks
Ian Goulding
Click to expand...
Click to collapse
I've installed Towa's GPS BT patch and the Jabra works perfect.
hey redbull,
what's the Towa's GPS BT patch and where can i find a link?
cheers mate
robson
Towa's gps patch has nothing to do with this...
I'm not sure what you are talking about, but Towa's patch will not solve the Jabra BT200 issue. The more important question to look at here is what version of BT200 you have. If you look on your Jabra BT200 right next to the microphone, there is a combination of letters and numbers, what does yours say? I think the problem has to do with issues in the firmware in the Jabra that were fixed in later versions.
It's usually 2 numbers and a letter on the boom to the Microphone.
I have a 47A and it does not work at all. Also tested a 48A and it doesn't work either.
mine's a 48b. works fine.
Cool, just so we are talking about the same thing, you can turn off the Jabra BT200, and turn it back on, and it still works with the phone? You can charge the headset in it's charger and pull it out and it still works? You can go out of range and then back in range and it still works? You can press the answer phone button on the headset when no call is in progress and then try to make a call and things still work?
Please try these various things and let me know.
I know that the A models are from 2002, and the B models are 2003. So it is possible if yours works with all these scenarios that they fixes or changed something in the 2003 models that allow them to work.
Thanks for your time,
LouisK
I recently purchased a BT 250 with nr. 44B and indeed it works with all the tests you described. (Don't need the BT GPS patch for that)
If only the advanced Headset Profile features would work with the MDA II I would be in heaven...........
Ok, it seems based on feedback I've gotten from several people that any Jabra Freespeak that has a "B" as the last part of it's version number will work correctly, but the "A" models do not. The "B" models according to Jabra are the most recent, and thought they don't admit it, there must have been a change in the firmware that allows the "B" units to work correctly with an XDA2/MDA2/i-Mate that the "A" units don't support.
LouisK
I have a "B" on mine and the same problem of rebonding when Jabra is shut off. I experimented by turning off bluetooth on the i-mate and it still worked. Anyone have ideas of a good headset that will not need rebonding?
I have problems with mine too and its a 16B. Turn the BT headset off and its rebond time again.....
48B works fine for me... can't everyone else just use TOWA's patch... that fixed the problem for others
stryker said:
I have problems with mine too and its a 16B. Turn the BT headset off and its rebond time again.....
Click to expand...
Click to collapse
16B is no good. I've been told that minumum needed is 19B. Below 19B is bluetooth 'handsfree' not 'headset'.
Towa's patch has nothing to do with this. It will not help in this situation. It only applies to Bluetooth Serial Profile, of which the Jabra has none. I have talked to Towa via email to confirm this. For those that installed Towa's patch and said it works, more than likely they didn't have the problem anyway because of the version of Jabra they had.
BT jabra 200/plantronic M3000
Jabra is model 45B, - no nead to repair, Plantronics M3000, no need to repair, but sometimes fails to answer call properly.
Hi 2U all,
I have just purchased a BT200 off Ebay, the number on the boom is 20B. No problems works well , no rebonding problems. Just one wish, it would work with voice. But I will keep praying!
StayLucky Jim :wink:
EMAIL FROM JABRA RE-Bonding Problems with XDA-II
:roll: :roll:
Dear Ian,
Thank you for your e-mail and please accept our apologies for the delay in reply.
We are sorry to hear you are experiencing problems using your JABRA BT200 headset in conjunction with your O2 XDA II.
However, having tested the JABRA BT200 headset with the XDA II, we have encountered the following problems.
When completed charging the headset you will need to synchronise the Headset and the Audio Gateway in your XDA II.
Please follow the steps below:
Select Bluetooth menu> Select Off> Select OK (BT is now disconnected)
Return to desktop (Today view)> Disable BT HS mode> Enable BT HS mode (User
to be prompted to turn On BT radio)>Select OK
Enter BT menu> Select On> Select OK (The XDA II returns to the "Today" view
and will try to synchronise with the HS again.
Check connection by establishing an outgoing call. If no sync - you will need
to re-pair the two devices)
We hope this will solve your problem for you. If you require any further assistance please do not hesitate to contact us again.
Thank you for contacting JABRA Customer Service, Europe
Camilla Vang
Customer Service Representative
GN Netcom, Mobile Division (Copenhagen, Denmark)
Click to expand...
Click to collapse
Seems to me that without actually saying it, JABRA think that the fault lies with the XDA-II!
Regards
Ian Goulding
question?? does the bt200 2.5 work with the imate and a i95c at the same time??
i have two devises an I95cl for nextel not blue tooth and the imate pc phone. i would like if possible to use one headset ?? the bt 2002.5 says it will work for bt phones also?? but will it work at the same time ?? hope iam clear...iam a baby here can you tell
15B, can it be upgraded?
Hello everyone...
I have an MDAII and a Plantronics M3000 BT headset and I have the same pairing problem.
I always have to repair the two divices for them to work...
Any ideas?
Best regards,
Rayan
I have bought a Plantronics M3000 bluetooth headset for my QTEK 2020. I have no problems pairing, calling and answering. However the headset just shuts off after a few minutes of conversation. It doesn't just cut the conversation but shuts off. I can make multiple short calls but nothing longer than 3/4 minutes. It works, however, without problems on my wife's Ericsson T68. Anyone can help ? Thanks.
Marek
Hello,
I have the MDA2 (same as QTek2020) and a Plantronics M3000 and It's been working just fine.
The problem you describe it's very weird since you mentioned that the headset works fine with your wife's mobile, and that makes me think that your QTek has some sort of problem with the Bluetooth stack or hardware.
It may be well worth to try (if possible) another headset just to make sure that is not the M3000 fault.
Do you see any type of error or message on the screen at the time of disconnection?
Does it always cut the conversation at the exact same moment?
Does the problem match the time the QTek takes to power save?
Any other clues?
Thanks.
I did not have the occasion to test another BT headset on the Qtek. When it shuts down there isn't any message displayed.
I have no problems with the BT stack (with the Pocket Bluetooth Tools patch) when using it with a BT GPS (Emtac) receiver, it works for hours.
However, your suggestion that it might happen when the Qtek goes in energy saving mode is interesting. I will check that tomorrow.
I'll post the result.
Hi
I seem to have a similar poblem after installing pocket bluetooth tools!.
I use a Jabra BT 250..and I noticed that the headset just mutes during the call..
I am generally used to switching off the display of the XDA after placing the call to power save ...
So I discovered that the headset would mute whenever i switch off the xda after making the call (which it never did prior to installing PBT)!
any thoughts on that?
maybe it has to do with the auto switch off plugin?
Actually I just experienced that too...
If I place (or answer a call) the next time I try to use the phone via the BT headset I notice the BT headset was turned off... Yeah, it could be related to the Powersave feature on the today plugin that PBT installs as a plugin... :roll:
Need to investigate...
Best regards,
Rayan
Both my bt headsets have stopped working since installing pocket bluetooth tools latest version, I have reverted back to version 1005 and everything is fine. I have a sony-ericsson EBH-65 and a skypower clip on headset.
my platronics does the same also its annoying you cant even transfer the call back to the device you have to hand up turn off bt and then turn it abck on and headset mode back on it also does the same on my pc
when im on msn using it as a headset it just d/c and i have to turn it off and turn it back on again
dont see what the problem is
btw the range on the xda2 and platronics is amazing i had it on my bedrooms desk and i went outside it passed through the living room wall and the patio window and i was stood 5m down my garden im sure it would of been over 10m and it was still working if i kept still when i moved it went crackly but ah well lol
just hope someone sorts the prob out
Hi,
I was having the same problem with the M3000. I just had confirmation from Plantronics that this problem is a bug in the product that occurs with the XDA II. I am currently in the process of returning the product.
Regards...Mike
Same problem M3000 doesn't work. Give up now before too much frustration makes you feel ill.
Try the Hello 2 headset. Work with my Aussie XDA2 and is very small and lightweight. Even had a neck chain to carry it around like a USB drive.
Hi and sorry for my bad english.
I have a problem with my Htc Touch Cruise and my bluetooth headset Motorola H700.
The headset worked fine with my ex P3600 but with TC have this problem:
when i receive a call, the headset responding correctly but after few seconds the audio disappears despite the bluetooth connection is ok!
If i shut off my headset the call continues regularly on TC, but if i re turn on the headset work correctly for few second and after stop.
The only solution is soft reset or turn off the bluetooth connection with commmanager and restart.
Someone have same problem?
Thanks to all!
Sirius75it said:
Hi and sorry for my bad english.
I have a problem with my Htc Touch Cruise and my bluetooth headset Motorola H700.
The headset worked fine with my ex P3600 but with TC have this problem:
when i receive a call, the headset responding correctly but after few seconds the audio disappears despite the bluetooth connection is ok!
If i shut off my headset the call continues regularly on TC, but if i re turn on the headset work correctly for few second and after stop.
The only solution is soft reset or turn off the bluetooth connection with commmanager and restart.
Someone have same problem?
Thanks to all!
Click to expand...
Click to collapse
No problem with my Samsung WEP200 BT Headset. In my case it work much better than with my old P3600 where people always complain about bad sound when I was in BT.
To be sure that your problem isn't linked to the Polaris, you should test with another headset.
Good luck !
academic said:
No problem with my Samsung WEP200 BT Headset. In my case it work much better than with my old P3600 where people always complain about bad sound when I was in BT.
To be sure that your problem isn't linked to the Polaris, you should test with another headset.
Good luck !
Click to expand...
Click to collapse
Thanks for your answer!
I try with another headset...
Sirius75it said:
Thanks for your answer!
I try with another headset...
Click to expand...
Click to collapse
I had similar problems with another HTC phone, same Motorola H700. Seems that the H700 might be the problem. I also use a Jabra without problems.
Sony Ericsson bluetooth headsets work also just fine.
butzchan said:
I had similar problems with another HTC phone, same Motorola H700. Seems that the H700 might be the problem. I also use a Jabra without problems.
Click to expand...
Click to collapse
I have the same problem with my Motorola H700!
Going to try an old Jabra headset this evening.
Sirius75it said:
Hi and sorry for my bad english.
I have a problem with my Htc Touch Cruise and my bluetooth headset Motorola H700.
The headset worked fine with my ex P3600 but with TC have this problem:
when i receive a call, the headset responding correctly but after few seconds the audio disappears despite the bluetooth connection is ok!
If i shut off my headset the call continues regularly on TC, but if i re turn on the headset work correctly for few second and after stop.
The only solution is soft reset or turn off the bluetooth connection with commmanager and restart.
Someone have same problem?
Thanks to all!
Click to expand...
Click to collapse
I have the same problem and sometimes I re-apply pairing between the headset and my polaris
same problem with Motorola H700. and olso motorola HS 810
They seem not to be compatible
I have reconnect my old carkit bluetooth Parrot CK3000 Evolution and with my HTC Touch Cruise work very fine!
With my old P3600, the parrot ck3000 evolution don't work fine but have problem with audio and connection, therefore i had unplugged and i had buy the headset Motorlola H700 thed worked well with P3600...
Same problem with Jabra headset
I have also exactly the same problem with a Jabra headset.
I found that the problem only occur when bluetooth is first activated on HTC and then activated on the headset. if I do it in the other way it works fine.
that's also the reason why it works after a soft rest of the HCT or disconnection reconnection of bluetooth on HTC.
Does it only mean that the headset is not compatible or is this a problem on the HTC.
Vincent
I don't know the bluetooth 2.0 + edr is compatible with motorola headset
perhaps a bluetooth incompatibility
i read on it http://direct.motorola.com/ENS/HKernel/H700_Headset_detail.asp
this : # Bluetooth Class 2 for wireless connection of to 10 meters
(30 feet)
# Compatible with Bluetooth 1.2- or 1.1-enabled mobile
phones, PDAs, PCs, and more that support headset and
hands-free profiles
I had the same problem with the H700. It connected fine the first day, and I used it for about 15 minutes. The next day, it wouldn't stay connected at all. Tried to re-pair, etc..no luck. My Jabra BT-125 works great, as does my LG HBM-730.
HTC patch for bluetooth
I saw on HTC (in the e-club section) that there is a patch for Touch (is it touch only or touch cruis also? I don't know) regarding "bluetooth connection problem".
Unfortunately I cannot download it.
If someone can do it, I'm interested.
Vincent
First of all sorry for my bad english!!
What about the patch for HTC TyTN II? this one seems to be like htc cruise, both of them have the same specifications, may be this patch work on HTC touch cruise
Where I can found the patch ?? I want to try it on my cruise. If don't work I will restore all with a backup file...
you can found it on HTC web in the e-club section. If the patch works properly write it in the forum please!
mesmo said:
First of all sorry for my bad english!!
What about the patch for HTC TyTN II? this one seems to be like htc cruise, both of them have the same specifications, may be this patch work on HTC touch cruise
Click to expand...
Click to collapse
Same specifications but different motherboard. Don't try it.
Ok......... thank you, I'll wait for another solution
After more and more test, I have found that the problem of the motorola Headset HS850 (and I think H700 etc. etc.) is the boom switch.
If you pair the headset to the Cruise and use it, it works fine (not stop after 3-4 seconds). Works great also bluetooth audio program:
http://www.freewarepocketpc.net/ppc-download-bluetooth-audio-v1-0.html
for redirect all audio to the headset.
But... if you switch off the headset with boom close, next time it will not work more than 3 seconds
So, the problem on this motorola is the automatic connection when open the boom.
Sony Ericsson HCB-700
Hi. I seem to be having similar problems. I had 3 phones linked to my HCB 700, and all worked fine. Very occasionally, I would have found that one wouldn't pair up when the ignition was switched on, but with my old Orbit 1, that may have happened once a week. I got a new Orbit 2, and was able to pair it easily. Now, it never fails to start paired, but frequently drops the BT connection. Usually a simple button press links it again, but it will rarely stay linked for more than 30 minutes, and could drop the connection 3 or 4 times in 10minutes. Then it may work for 30 minutes. I tried a reset to default settings, and re -paired the two again, but it doesn't seem to have made any difference. This can happen whether I have used the phone or the handsfree or not.. I'm thinking of getting a Parrot kit now instead - any ideas? Thanks in advance..
Hi if someone can help me it would be much appreciated. I just bought a Touch Pro and everything is working fine....except for one really annoying issue.
Whenever I connect my bluetooth to a headset, it shows connected but no sound is coming out. The sound is muted. when connected to my Audi, I see that the phone has bars (shows connected and I can dial the phone), but when I make a call no sound. Similarly on my SE HBH-DS970 headset. The A2DP works perfectly, but when I make a call nothing.....I've searched google and through XDA and no solution.
Can someone suggest a solution? I've soft/hard reset the device already. If I should change Radio ROM which one would someone suggest that's stable? Thanks
If no one else has this problem, can anyone at least suggest to me if this sounds like a Hardware or software issue? If hardware I will return it, but if software I will try to find a solution. Like I said the phone connects to BT, but I just can't get handsfree to work. File transfers and A2DP work. Thanks
Just flashed to UK ROM and still no help....I've read some people having the same problems over at the Diamond thread...I'm the only one answering my own thread here hahaha....if anyone can help I'd greatly appreciate it. Thanks.
Hi,
I occasionally had such an issue with my Parrot CK3100, but I did not get the time yet to investigate further. After the call was connected I did not hear anything, and I am not sure whether the other party could hear me.
On another day, the handsfree was working perfectly OK.
Cheers
Michael
Thanks for replying Michael....I'm at a loss and I tried all the suggestions posted. I hope it's a software issue...I'm going to buy a bluetooth headset tomorrow and see if that works. It's not the end of the world, but annoying since all my ppc, s60, BB, and UIQ phones prior to the TP have not had any such issues.
Do you think it's a software issue?
have you tried playing music?
Yes.....A2DP works perfectly....no problems whatsoever with file transfers either....I'm guessing either it's a software problem or the phone has a new bluetooth software that's not agreeing with my older SE headset, but the car is another issue. The Car is 2007 and I'm sure the Bluetooth software is not that old. I've tried Euro WWE and Asian WWE ROM and no go.....I'm going to try the Cingular ROM and see what happens.
Just another quick update....I tried 2 other different bluetooth headsets and still the same problem... for some reason the sound for handsfree will not come through...anyone know of registry hack possibly that will allow sound to come through?
May not be entirely related to your problem...
Mine is worst...whenever I have paired my Jabra or iTech BT headset, when the phone rings, 8/10 times the phone will auto pickup (and no I did not setup the phone to auto pickup) and the it will NOT connect to the bluetooth. Instead it will be just like an auto pickup and the sound will come thru the phone headset. This is driving me nuts!!!!