please if you have a english pocketpc running on your phone and you have a serial kable
this will only take 5 minutes !
please dump the rum doing the following
Here is the steps to backup the ROM to a file:
1. Connect via Serial cable to XDA II
2. Put XDA II into Bootloader Mode (power button+any direction+reset)
2b. get HyperTerminal Private Edition ftp://ftp.hilgraeve.com/htpe/htpe63.exe
3. Run Hyper Terminal 115200 baud, 8n1, direct to com port.
4. Issue d2s command to backup ROM to SD. You'll need an empty SD card with 64Mb or more size (i used 128)
5. Once the ROM is dumped, reset your XDA.
6. Put the SD card to your card reader.
7. Use ntrw (http://home.comcast.net/~kenzhao8/downloads.htm, it is in cfutils.zip):
ntrw read test.nb1 m:
This assumes your SD card has drive letter M:
8. Copy the nb1 rom file to a zip and post it to a site.
Then we can download the ROM, unzip, use ntrw to write back to SD and go into bootloader mode with SD card inserted, hit camera button and flash our MDA II to english rom.
thanks to PalMop for the info
Update, I got a copy of the English ROM !!! It was dumped via pmemdump (http://www.xs4all.nl/~itsme/projects/xda/tools.html) using:
osimage: 'pmemdump 0x80040000 0x01fc0000 osimage.nb1'
bootloader: 'pmemdump 0x80000000 0x00040000 bootloader.nb0'
I am still trying to figure out how to dump this image to SD. My ntrw.exe method above works, if you created the SD via serial. The pmemdump method uses ActiveSync and USB cable, so it is easier to create the file. But we don't know how to put it onto SD yet.
So if anyone wants the English ROM created by pmemdump, pm me where to upload (or German one as well)
Have you tried XDA OS Image Tool from http://xda-developers.com/XDArit/?
Guys and gals, I now have a English MDA II. Special thanks goes to Willem and KullTogi for their help.
I compare my original ROM and the English ROM dumped by pmemdump. First 412 bytes were missing. So I added that, removed last 412 bytes, copied the file to SD via ntrw and it works.
I have the patched file and the ntrw.exe for anyone wanting it. If anyone can open a FTP to host, I can upload there for everyone's use.
One note, after upgrade, the checksum will fail at the end of process. But don't worry.
Awesome!!! I want it.
Palmop:
How big is the file you need to upload? I want to get my hands on the english ROM!!!
Thanks,
Fernando
File is 16Mb. It is being uploaded to a FTP site , Akira will provide details shortly
strange for an rom to be 16 mb
thought ppc2003 was 32 at least
I said file is, not rom is , there is the good old zip compression. If anyone can arrange FTP access, I can upload it there. I have no access to a FTP server, I am looking to setup one.
PalMop
i just mailed you a new one
Please post the ftp site here...
for those of us itching to download. Thanks !!!
Fernando
I have an FTP site that can host this.
Palmop:
I can host it here:
ftp://www.shawus.com
username: hydrosphere
password: 12345
Please upload it there and post a message here when its done.
Thanks!!!
Fernando
http://www.vogtschmidtoutdoorcenter...h ROM by PalMop/xdaii-usa-rom-1-03-palmop.zip
ill leave it for 48 hours
note: it did not work for me
when i put it in booloader, and pres camera it says
SD DOWNLOAD
Section=1
Not allow update!
**update :
did same as palmop
downloaded my down rom, and hexedited it, copyd the header part
replaced it in the new rom
tried again and worked
It said on my 2 devices:
SD DOWNLOAD
Section=1
Press Power to download
(or something similar, I hit the power button and update is done)
My file I sent to you via FTP was already patched (the first 412 bytes), weird
it failed
Upload to Orinoco's FTP is complete as well
Steb-by-Step Instructions?
Akira and Palmop:
Would it be too much to ask a step-by-step to get this done properly. I want to do it, but am afraid to screw up my new device. Thanks in advance for all your efforts.
Fernando
It was in the text file (how to.txt), inside the ZIP I uploaded
Here it is:
1. Extract the files to a folder.
2. Put 64Mb or larger SD to SD card reader.
3. Go to command prompt, switch to the folder from step 1.
4. Type:
Ntrw write 1-03-00-USA-xdaii-patched.nb1 g:
(assuming SD card reader has drive letter g:, change accordingly)
5. Once copying is finished, wait a minute, get the SD out, insert into MDA II, select Nein if it wants to format the card.
6. Go to Bootloader mode (power + direction + reset), hit Camera button couple of times
7. When it asks to press power button to flash, do so.
8. It will flash the rom, at the end there will be a checksum error, that is normal as the bootloader has not been changed.
9. Reset.
10. Device is ready to use.
it worked !
problem is , everybody needs to implant their own header, i think its header sensitive.
ik used a hex editor and deleted the first 420 bytes
not that word part that you see in the file. first time i also selected the word part at the end of the header.
and then copied the header from my own rom
and placed it their
now it works
Hi all !
I dumped my original ROM (German) from XDA2 and read with 'ntrw' but the file size is 128.450.560 bytes.
Something wrong ? Or what ?
THX any replay
In ftp site are three ROM posted :
750v:34 MB
TREOCINGULAR: 16,4MB
treo750vrompartial_bcaslis.zip:34 MB
Now i have a Vodafone Rom in italian languadge , the ROM posted are in english?
what are the difference trough the posted ROM'S ?
How can update my Treo ?
Kindest regards
Uccio
Try checking the treo wiki and read through everything before trying to perform the rom upgrade. Remember that a simple mistake can and might render your device useless.
How to!
zerimar said:
Try checking the treo wiki and read through everything before trying to perform the rom upgrade. Remember that a simple mistake can and might render your device useless.
Click to expand...
Click to collapse
"Insert the reader w/card into your USB, after the PC recognizes the card right click on the drive letter. Select Format from the options and make sure FAT32 is selected as the file system then select start.
Also, you need to copy the files to the memory card one at a time; DIAG file first and then delete the DIAG prior to loading the IMG file second.
Step 1:
-Copy the ‘CheeDIAG.nbh’ file to the root directory of a miniSD card. Note: Windows Mobile recognizes updates only from FAT32 formatted cards.
-Insert the card into the device.
-Press and hold both the PTTApp Button (lowest button on left side of device) + Pin Reset (next to miniSD card slot). You will be prompted to press the ‘End’ (red power) key to start the update. This step takes only a few seconds to complete. Once the flash is done, you will see: ‘Model ID: Palm Treo 750’ displayed by the device.
Step 2:
-Copy the ‘CHEEIMG.nbh’ file to the root directory of a miniSD card. Note: Windows Mobile recognizes updates only from FAT32 formatted cards.
-Insert the card into the device.
-Press and hold both the PTTApp Button (lowest button on left side of device) + Pin Reset (next to miniSD card slot). You will be prompted to press the ‘End’ (red power) key to start the update. This step takes about 5 minutes to complete.
-Hard reset the device once the device indicates the upgrade has been completed. To hard-reset, hold the ‘End’ (red power) key while pressing the pin reset button. Answer “yes” to “Erase all data” prompt.
Step 3:
Verify the device software via the device <start><settings><system tab><about><phone tab> The device should display firmware version on the resulting screen."
Good luck!
excuse me for asking,but there`s no file called ‘CheeDIAG.nbh’ or `CHEEIMG.nbh’ in files that are in the /Cheetah/Dumped_ROMs/ folder!
750v:34 MB consists of 3 .RAW files(What to do with them?)
treo750vrompartial_bcaslis with .RAW files inside,also
Treo750v_Dump_Cingular_ROM.zip with .dll`s mostly
Did I understand something wrong....?
Any help
THX in advance!
Roms
There are NO installable roms on the FTP!
The usable one is in the possesion of forum members.
Palm and/or Cingular asked politely ;-)) to remove them.
So you have to wait untill the new rom will be released later this month
i didn`t have time till now to wiew all the posts about this phone,and only now I saw that still there aren`t ROMS available.
If anyone has a ROM or a link for it,pls PM me!
THX in advance!
I've been on the web for hours, trying to learn how to upgrade a Treo 750v to WM6.
Thanks to XDA, I think I've got it worked out ...
1. download the ROM
2. extract and rename the .nbh file ***
3. put the CHEEIMG.nbh file on a FAT SD card
4. run the bootloader
5. hard reset.
OK - looks easy ... EXCEPT ...
I dont have a windows PC (OK - so I'm a Mac user), so how can I extract the .nbh file from the .exe file ?
OR - can anyone post a link to the .nbh component of the GENERIC ROM which I found at ...
http://palmone.r3h.net/downloads.palm.com/Treo750_2_23_ROW_EN_DesktopUpdater.zip
Assuming that the .nbh file is all I need ????????
OK - I'll answer my own post ...
1. Download the ROM
http://forum.xda-developers.com/showthread.php?t=335402&page=8
2. Borrow a PC to extract the .nbh files from the .exe file.
3. Rename CHEEIMG_FW.nbh to CHEEIMG.nbh
4. Format an SD card as FAT32.
Amazingly, WM5 doesnt contain a utility to do that.
Use a PC and do it from Windows (provided the PC has a SD reader).
5. Copy CHEEIMG.nbh to the root level of the SD card
6. Back up all your Treo data
7. Insert the SD card into the Treo
8. Hard reset the Treo (Reset + Power button -> erase all data = Y)
9. Press Media + Soft Reset -> bootloader mode
10. Follow the prompt -> hit the Power button to start the update
11. Wait about 10 minutes -> done
12. Reset the Treo
BINGO - WM6 is up and running !
I used the generic ROW English ROM ...
So my Treo is UNLOCKED - no Telstra splash screen - great !
Phone works - internet works - BT works ...
Only problem (so far) seems to be that all Treo-generated sound (such as Screen taps - which all worked fine initially) has now been muted.
help me..when i try to install sd rom (MCCM DS V4.0).when i perform the following steps after extracting the rom
Boot with MAGDLR:
1- copy folder (Android) to SD Card .
2- Boot in MAGDLR powering on your phone while you press the power button until MAGDLR appears.
3- Select "SERVICES"
4- Select "BOOT SETTINGS"
5- Select "AD SD Dir"
6- Select the "ANDROID" folder or the folder where you dropped the rom.
7- Now select "BOOT AD SD" and wait boot .....
i receive load zImage and SD kernel open failed message in red. what do i have to do..am i missing something like latest kernel..? plz help me.. the folder does contain a file zImage
Guys, Help, I get to No 3 of the instructions listed below, the box disapears and nothing else happens, I have downloaded from the links from here http://forum.xda-developers.com/showthread.php?t=893948, from these links
3. Download MAGLDR 1.13 package from *HERE* and extract to an empty folder on your pc
4. Download a NAND Android ROM from *THIS* Forum and extract to an empty folder on your pc any tips on how to over come the problem, keep the suggestions simple please
I've followed the instructions, but keep failing at No3 ....
Please help, lol, and keep it simple lol
1. FLASH MAGLDR TO YOUR DEVICE
The Original MAGLDR Thread by Cotulla is *HERE*
NOTE1: LEO512 and LEO1024 are both supported
NOTE2: MAGLDR doesn't replace OSPL/HSPL. It runs in the chain after. So it's safe to install and remove it
NOTE3: You can flash between 1.11, 1.12 and 1.13 versions on Magldr without losing your NAND Rom
1. Synch Phone with PC in Windows Mobile!!! It has to be connected to activesync or WMDC via USB cable
NOTE: As an alternative method to activesync you can restart your phone in Bootloader Mode, then connect the usb cable and wait until 'usb' appears in the bottom half of your phones screen
2. Browse to the folder you extracted your Magldr Package files to on your pc, right click on ROMUpdateUtility.exe and select Run as Administrator
3. Tick the box to confirm you are aware of the risks and select 'Next'
4. Tick the box to confirm you have followed the preperation steps and select 'Next'
* The program will now check the usb connection *
5. Select 'Update'
6. Verify the image you will flash (it should say 2.00.000.0) and Select 'Next'
7. Read the process list and Select 'Next'
8. Your phone will enter BootLoader Mode and the progress will goto 100%
9. Your phone will now Reboot. Congrats, you just flashed MAGLDR.
NOTE: To Enter MAGLDR Menu Screen after installation, Long Hold the Power Button when resetting the phone and the menu will appear