There are two screws on the bottom of the Tf by the charging port. Then on the back there are clips all around the outer edge of the "Asus" panel. Use any non marring tool for the clips. Once all the clips are loose, the bezel around the screen comes off frome the front. It seems to bemostly plastic with a metal overlay. Then there are ten or eleven philips screws that hold the rear panel on.
Sorry no pics
So the metal bezel comes off first then followed by the plastic back panel which is held in by screws?
Sent from my Transformer TF101 using Tapatalk
Thats correct. You can see the screws for the back after the bezel is removed.
The metal around the edge is seprate from the back plastic and the front glass. However the metal is extreemly thin and WILL bend with any kind of proping. Also once u remove it getting dust under the glass is going to happen. Also the plastic clips are very ****ty and if one bends or brakes the transformer will not click back on. Its not worth opening this thing up. If u have a issue with your unit call asus and have them fix or return to store.
cowballz69 said:
The metal around the edge is seprate from the back plastic and the front glass. However the metal is extreemly thin and WILL bend with any kind of proping. Also once u remove it getting dust under the glass is going to happen. Also the plastic clips are very ****ty and if one bends or brakes the transformer will not click back on. Its not worth opening this thing up. If u have a issue with your unit call asus and have them fix or return to store.
Click to expand...
Click to collapse
Thanks to everyone who posted this information!
The only thing that bothers me about the TF is the creaking, so I was thinking about fabricating some pieces to upgrade or replace the back, bezel, or both.
couple of questions for you...
--Were you able to determine exactly where the creaking comes from? Is it just the flimsiness of the back panel or the way it all mounts together?
--Also, you mentioned dust getting under the screen after reassembling- so the glass is a completely separate component? How does it attach to the rest of the unit?
--Finally, are there any warranty/tamper seals that get broken during dissassembly?
Thanks again!
I didn't go any further than removing the bezel out of fear that I would break something or not be able to get it back together. I didn't get any dust under my screen and there wasn't a single tamper seal that i saw
Has anyone found a replacement lens cover for the DoubleShot? The only one's I could find online are attached to the rear housing (which makes sense), but I don't want to lose the serial/imei sticker on the back. My wife scratched up the lens cover enough to bother me.
If worst comes to worst, you can move the sticker.
I've replaced the entire body of a MT3GS and I managed to pull the manufacturer's stick off without too much trouble. Heat it with a hairdryer for a few mins to soften the glue and it should pull off easily. Then depending on the residual stickiness, you can simply transfer it over or add a little additional glue.
I was trying to change digitizer to my tf300 by following this video http://www.youtube.com/watch?v=3_JRLd7lPv8 .The video is really bad, considering that this guy will show you a tf300 that has been opened before or something, because its very easy for him to do certain things, that i found very hard,and had to use other techniques.For example, i had really hard time separating the old digitizer and the plastic frame. In order to separate these two parts, i used some heat blowing gun (professional one) which turned to be very effective separating the digitizer from the plastic frame, but the plastic got wraped (as you can see in pic). Also, i don't have an adhesive tape or glue in order to stick the new digitizer to the frame so i m unable to stick the new digitizer to the frame.
https://www.dropbox.com/s/bwz1cw2pu1zrgst/IMG_20131010_135139.JPG
TheoKondak said:
I was trying to change digitizer to my tf300 by following this video http://www.youtube.com/watch?v=3_JRLd7lPv8 .The video is really bad, considering that this guy will show you a tf300 that has been opened before or something, because its very easy for him to do certain things, that i found very hard,and had to use other techniques.For example, i had really hard time separating the old digitizer and the plastic frame. In order to separate these two parts, i used some heat blowing gun (professional one) which turned to be very effective separating the digitizer from the plastic frame, but the plastic got wraped (as you can see in pic). Also, i don't have an adhesive tape or glue in order to stick the new digitizer to the frame so i m unable to stick the new digitizer to the frame.
https://www.dropbox.com/s/bwz1cw2pu1zrgst/IMG_20131010_135139.JPG
Click to expand...
Click to collapse
You used too much heat. I don't think the warped frame will fit anymore. You might need to buy a new one. You really don't need heat initially though. Since you were gonna discard the broken digitizer anyway, you should've just scraped the glass off. Use this type of adhesive to glue back.
Thanks for you info!I was thinking of puting the frame on a table, put the new digitizer to fit as much as possible, put some towel on, and then heat it again by gently pressing it with the iron.Else, where can i find a replacement part?I don't even know the name of this specific part so i can search for it.
TheoKondak said:
Thanks for you info!I was thinking of puting the frame on a table, put the new digitizer to fit as much as possible, put some towel on, and then heat it again by gently pressing it with the iron.Else, where can i find a replacement part?I don't even know the name of this specific part so i can search for it.
Click to expand...
Click to collapse
It's the front plastic bezel. Sometimes it's available used on Ebay. Best place to inquire would be Asus Parts located somewhere in Europe. I wouldn't try what you're thinking of doing unless you can straighten it again using the broken digitizer, as the screen is extremely brittle and the slightest pressure might crack it.
Alright, I did send sms on my bicycle which resulted in I did drop the phone on the ground. Luckily I had ad NILLKIN glass screen protector, which did save most of the phone . I have ordered a new Nillkin screen protector from Aliexpress. And I hope to patch up this phone so it looks good again. How would you have done ?
As you can see at the bottom in the pictures there is physically damage, you can you see the screen bleeding thru also the huwawei logo is damaged.
My idea is UNDER the NEW Nillkin screen protector I will try to mask these "holes" so the screen is not beelding thru anymore. What material should I use to patch up these holes.. also.. how to repar the logo ? can I print it out on my computer printer ? it might look **** on paper but UNDER the glass protector it might look a lot better.
All creative ideas are appreciated, I have high hopes the phone will look good again..
And hopefully my phone will surrive until the M8 release.
Just to let you know desipite the glass look damaged like this the phone is still fully functional!!
ouch i can feel with you.
How about some black film, black paper or everything else that is black and thin
Yes some black material for sure.. Black film would be perfect in guess.. Just wonder where to get it also some black glue at the sides also..
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
alexre123 said:
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
Click to expand...
Click to collapse
Nice man might be a very good alternative! But how easy is it to change it really?
Do I need a heat gun for that?
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Or...if you have the courage go for it ) - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Joke man, don't do it yourself if you don't have experience
alexre123 said:
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Click to expand...
Click to collapse
I have done some smartphone repair myself, I changed the USB board on my old Galaxy Note 1.
I bought a smartphone repair kit with a few tools and very small screwdrivers. To change the glass is probably not much harder, but I need to know if I need a heat gun since I do not own any yet Hopefully it is not needed..but I would assume so...
I might also add the reason I bought a screen protector was that the original glass underneeth have a small crack too that goes accross the entire screen but it s quite invisible besides from certain angels.. so to change that screen to would actually be amazing..and it would make the secondary value when I sell this when M8 is released be a lot higher..
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
alexre123 said:
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
Click to expand...
Click to collapse
Yes the Nillkin glass did its job but I think I was unlucky, that the bottom of the phone got under my bicycle tire.. it felt like it...
I recommend Nillkin, IT has very good Oleophobic coating, which makes the whole device a lot more enjoyable to use, but be careful whren you put it on non 100% straight surfaces it will slip onto the floor.
Alright it is more or less decided I will buy a new front cover with glass, I will make sure to get original parts with gorilla glass. Since the ebay link you linked to are chipped from china I guess I can just order straight from alixpress instead...
I have heard singapore post have quite fast shipping compared to china post.
just one question is hard to see in the videos.. but do I really need to disassembly every component all the circuits boards just to change the front screen ? do I need to open the case at all when using the heat gun/hair dryer ?
If as in the every component and circuit board has to be disassembled it is over my competence probably... unless I am super careful..
Mutch better if you want to purchase an original front to replace it. Don,t know if you really need to take all the components of for replacing the front screen, but you can make some research on it or you can ask on other forums, maybe are others with more experience.
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
blackinfinity said:
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
Click to expand...
Click to collapse
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
ehhm... good luck OP
XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
blackinfinity said:
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
Click to expand...
Click to collapse
Sorry but you are like 10 year old child..
So u wanna change your ''front Screen Outer Glass Lens'' ??? (that is damn long name for glass )
You have so much hopes ? OK .. go on .. I leave you to it ..
I wish you very best of luck ..
''''IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT''
DDDDDD this was so funny :laugh: :good:
Fingers :fingers-crossed:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
blackinfinity said:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
Click to expand...
Click to collapse
And I will give you one last advice ; that my detailed post above I explained you how difficult it is .. YOU want to change glass only ??
And what you think, you can just do it without stripping phone apart ?? Are you magician ? You would have to open phone anyway !
And replacing glass on your screen, do you have any idea how you gonna do it? Removing glass from LCD is x10 TIMES hard that my instructions above man !
So you basically adding even more, harder work to hard work ..!
Do you even have
1.LCD separator heat machine ??
2.Cutting line wire ??
3.Cleaning alcohol chemicals ??
4.Optical clear adhesive glue ??
5.Ultraviolet curing lamp ??
Come oon man ...
I told you I wish you very best of luck..
This guy want to do the exact same thing - https://www.youtube.com/watch?v=O8HNBtl9MwI
You have the all process here - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Take a look and decide if you want do it yourself and risk to mess things up or go with the phone and the replacing part to a service and let someone who did this before.
Did anybody try replacing the glass screen on the LG G5? Not the whole digitizer, screen only.
Looks like replacement glass is found quite cheap.
http://www.ebay.com/itm/OEM-Front-O...eplacement-For-LG-G5-H820-VS987-/222227276105
There is a crack on my screen, the touchscreen is perfect. Is there a procedure somewhere that can be followed to get it done? I see a lot of videos for a complete teardown. But is it possible to just use a heatgun to take the glass off and put the new one in?
These display modules are oftenly replaced altoghether, because replacing only the glass requires it to be really precisely fitted and hermetically glued, you can probably try to seperate the digitizer from the display, but you may end up with a some dust underneath the glass or some unwanted gaps.
suhridkhan said:
Did anybody try replacing the glass screen on the LG G5? Not the whole digitizer, screen only.
Looks like replacement glass is found quite cheap.
http://www.ebay.com/itm/OEM-Front-O...eplacement-For-LG-G5-H820-VS987-/222227276105
There is a crack on my screen, the touchscreen is perfect. Is there a procedure somewhere that can be followed to get it done? I see a lot of videos for a complete teardown. But is it possible to just use a heatgun to take the glass off and put the new one in?
Click to expand...
Click to collapse
I had a crack on my screen at the top of when it fell down on concrete floor. I had to buy the whole display with glass and digitizer for about 130 euros. I did not know that you can just buy the glass and replace it with a lower price. Oh well... but if you want to separate the glass from the digitizer or anything what is glued, always use the heatgun. You can also use the hairdryer. I had to replace a battery by opening up a back cover with a hair dryer. For separating the glass from the digitizer you have to heat it up very often, pry it open and hold at several spots, to avoid breaking components. It s quite difficult but take it slowly.
fosunite said:
I had a crack on my screen at the top of when it fell down on concrete floor. I had to buy the whole display with glass and digitizer for about 130 euros. I did not know that you can just buy the glass and replace it with a lower price. Oh well... but if you want to separate the glass from the digitizer or anything what is glued, always use the heatgun. You can also use the hairdryer. I had to replace a battery by opening up a back cover with a hair dryer. For separating the glass from the digitizer you have to heat it up very often, pry it open and hold at several spots, to avoid breaking components. It s quite difficult but take it slowly.
Click to expand...
Click to collapse
So, if I crack my screen I need to get a screen replacement with frame or just screen replacement?
Screen replacement with frame
https://www.fixez.com/store/lg/lg-g5/lg-g5-display-assembly-with-frame
Screen Replacement
https://www.fixez.com/store/lg/lg-g5/lg-g5-display-assembly-lcd-and-digitizer
You can get without the frame, you will just need to heat up the glue between the frame and old screen to cut through the glue to remove the frame. They cover it on the instruction video on Fixez.