I have a Netgear WNDR4000 router. I am using WPA2 security, static internal IP addresses and a MAC table to control access to my home network. I have added multiple devices to my home network since I bought the router without any issues including an Android smartphone running gingerbread.
No matter what I do I cannot get my 300 to connect to the network. It does see the network SSID but it will not connect. I even tried the WPS button on the front of the router using the advanced settings on the 300 but still no luck.
I am beginning to think that the MAC address listed under the “About Device" menu item is not what the 300’s radio is actually broadcasting.
I have double- and triple-checked all the settings but I am getting nowhere.
Any help or suggestions you may have would be appreciated.
Does your smartphone support tethering? Connect the 300 to it to verify MAC address. You could TEMPORARILY reconfig your router to be open (no security) and confirm MAC address. Turn off MAC filtering to see if that is it. Get it to connect to something wide opeb and then begin layering on the security.
You have set up your static settings on the 300, correct? Sounds like you have DHCP disabled on the router...
Sent from my SCH-I510 using XDA
Thank you for your response.
I did finally decide to take all the security of the router and the 300 connected right away. Then I checked the router's "attached devices" list and it did verify the MAC address that the 300 was displaying. So I was able to clear that as an issue.
I still could not get it to connect with my WPA2 security turned on (my router needs that level of security to put out "N" speeds) on the 2g network.
Right; I have DHCP disabled on the router. All my devices, wired and wireless, get an assigned internal IP address and their MAC addresses are loaded into a table.
Every other device I've added to the router connects without a problem.
I decided to send the 300 back and I'll just wait for the Infinity to hit the market.
Thanks again for your help.
Hope your next one works as it should. Mine connects fine using WPA or WPA2, multiple manufacturers. Still waiting for OTA, rooted running .17 firmware.
Sent from my SCH-I510 using XDA
ptgay49 said:
Thank you for your response.
I did finally decide to take all the security of the router and the 300 connected right away. Then I checked the router's "attached devices" list and it did verify the MAC address that the 300 was displaying. So I was able to clear that as an issue.
I still could not get it to connect with my WPA2 security turned on (my router needs that level of security to put out "N" speeds) on the 2g network.
Right; I have DHCP disabled on the router. All my devices, wired and wireless, get an assigned internal IP address and their MAC addresses are loaded into a table.
Every other device I've added to the router connects without a problem.
I decided to send the 300 back and I'll just wait for the Infinity to hit the market.
Thanks again for your help.
Click to expand...
Click to collapse
Wtf... Send it back.... Wow!
Sent from my SPH-D710 using xda premium
Hello all!
Not sure if this has been posted but I figured I would put up a new post. I am showing that I am connected to my home WiFi but I am not able to actually use it. For instance, I cannot open links or watch YouTube videos. I believe it is the router because I just had a Droid RAZR and my connections to the Internet were not dependable. Currently, I am using AT&T's 2Wire 2701HG-B Gateway router.
Are there any settings that should be adjusted within the router? Encryption type is WPA-PSK. Wireless mode is 802.11g/b.
I just got my S3 yesterday and so far WiFi works in other places. Also, I tried the #*0011# thing and that did not work for me. I've rebooted and factory reset my device. Nothing helps. Anything I can change?
Thanks in advance!
Does your router Administration panel (perhaps accessed via a web browser?) show your phone as connected with an assigned IP address?
- ooofest
ooofest said:
Does your router Administration panel (perhaps accessed via a web browser?) show your phone as connected with an assigned IP address?
- ooofest
Click to expand...
Click to collapse
Now that I'm looking, no it doesn't have it listed there. My phone says its connoted though. I forgot the connection, rebooted the phone and did the #*0011# and reconnected the network. Still the same result. Any ideas?
I've seen some routers being a bit buggy about showing all wireless-connected devices (my dual-band Netgear comes to mind), so I can only think of a few things to check:
This assumes your router is configured for DHCP and that you have addresses available in its configured range, etc.
1. Does anything else use this router successfully to access the Internet?
2. On your phone, Settings -> Wi-Fi->(click on the wireless network you are "Connected" to)->View, does it show an expected speed and a valid IP address from your router?
3. If (2.) revealed a valid IP address on the phone, can you ping that address from another system attached to the same router?
4. Did you connect the phone using a typed-in passphrase on both router and phone or by using the Wi-Fi Protected Setup (WPS) push-button method on the router? I found that, no matter how carefully I typed the passphrase, it often would not connect to my desired network because something was somehow amiss. However, this phone is compatible with using WPS, so I used the router's push-button method and it connected easily + worked fine.
Just some things to check and ensure nothing critical is amiss.
- ooofest
ooofest said:
I've seen some routers being a bit buggy about showing all wireless-connected devices (my dual-band Netgear comes to mind), so I can only think of a few things to check:
This assumes your router is configured for DHCP and that you have addresses available in its configured range, etc.
1. Does anything else use this router successfully to access the Internet?
2. On your phone, Settings -> Wi-Fi->(click on the wireless network you are "Connected" to)->View, does it show an expected speed and a valid IP address from your router?
3. If (2.) revealed a valid IP address on the phone, can you ping that address from another system attached to the same router?
4. Did you connect the phone using a typed-in passphrase on both router and phone or by using the Wi-Fi Protected Setup (WPS) push-button method on the router? I found that, no matter how carefully I typed the passphrase, it often would not connect to my desired network because something was somehow amiss. However, this phone is compatible with using WPS, so I used the router's push-button method and it connected easily + worked fine.
Just some things to check and ensure nothing critical is amiss.
- ooofest
Click to expand...
Click to collapse
1. Yes, my iPad and two laptops.
2. There is a link speed and an IP address but the third number of the IP address on my phone is different than the third number of the IP addresses of the devices listed that connect to the router. I hope I made some type of sense saying that lol! There are about 6 devices listed that connect to the router and the first, second and third numbers are the same. My phone only have the first & second numbers in common.
3. didn't try that because I'm assuming something isn't right from the previous answer.
4. I typed in the pass phrase from my phone. I do not know of any other way to connect the device. I am not familiar with doing it from the admin panel especially since I'm not even seeing the device there.
Thanks again!
Yeah, not getting the proper address range would be indicative of a problem authenticating with the router, I'd suspect. If you are using the default router configuration, it should have an IP address of 192.168.1.x, where x = {some number}
You might try temporarily setting the router to "WEP-Open" and no passphrase on the phone (i.e., connect to the open network) to determine if the phone can obtain a valid IP address from this router before doing more debugging. This might weed out the possibility that this new phone has an inherent problem connecting with your specific router - even though other devices don't have such issues, maybe the Galaxy S III is sensitive in this regard.
Consider ensuring that the "Power setting" in your wireless configuration is at its maximum value (10?).
Aside, I don't know if the latest firmware enables WPA2-PSK, but that utilizes AES and is often more efficient than WPA-PSK, from my understanding. If using WEP-Open works for your new phone in the above test, then consider setting the router to "WPA-PSK and WPA2-PSK" (if it has that value) and try reconnecting using the passphrase (either 10 or 26 letters/numbers) - that setting should be compatible with your other devices and not require them to be reconfigured, I believe.
This topic seems to indicate people have problems with your model of router in making and keeping wireless connections at times, sometimes needing to hardcode the router down to only use "b" protocol (i.e., slower) for maintaining stable connections. I don't think that's the case here, though.
This User Guide (.pdf) for your router model does not seem to show that it offers WPS as an alternative for establishing device connectivity. From my recollection, my phone would only connect reliably to the router using encryption when I used the WPS button on the router. That's why I asked you to set your router to be Open for a test.
- ooofest
I had the same issue as you. I would be connected to my router and nothing at all. I am using a att modem/router along with my netgear wndr3800. But wifi was dropping a lot of the time. I never had this problem before when I had my Rezound. 3 days before I got my S3 I upgraded the firmware on my netgear router. I am guessing my S3 didn't like the firmware update or something. I tried everything in the router settings to doing a factory reset on both the att modem and my netgear router. Nothing... So I honestly thought it was my phone. Called Verizon and asked them to ship me a refurbished. So, I thought I would try one more thing. Revert back to my old firmware on the netgear router. Well it worked. Since Friday night I haven't had the issue you are having. Connected to my home wifi with no drops at all. It could be the firmware. Wonder if you could revert back. On a att modem/router I am not sure.
Sent from my Samsung Galaxy S3
ooofest said:
Yeah, not getting the proper address range would be indicative of a problem authenticating with the router, I'd suspect. If you are using the default router configuration, it should have an IP address of 192.168.1.x, where x = {some number}
You might try temporarily setting the router to "WEP-Open" and no passphrase on the phone (i.e., connect to the open network) to determine if the phone can obtain a valid IP address from this router before doing more debugging. This might weed out the possibility that this new phone has an inherent problem connecting with your specific router - even though other devices don't have such issues, maybe the Galaxy S III is sensitive in this regard.
Consider ensuring that the "Power setting" in your wireless configuration is at its maximum value (10?).
Aside, I don't know if the latest firmware enables WPA2-PSK, but that utilizes AES and is often more efficient than WPA-PSK, from my understanding. If using WEP-Open works for your new phone in the above test, then consider setting the router to "WPA-PSK and WPA2-PSK" (if it has that value) and try reconnecting using the passphrase (either 10 or 26 letters/numbers) - that setting should be compatible with your other devices and not require them to be reconfigured, I believe.
This topic seems to indicate people have problems with your model of router in making and keeping wireless connections at times, sometimes needing to hardcode the router down to only use "b" protocol (i.e., slower) for maintaining stable connections. I don't think that's the case here, though.
This User Guide (.pdf) for your router model does not seem to show that it offers WPS as an alternative for establishing device connectivity. From my recollection, my phone would only connect reliably to the router using encryption when I used the WPS button on the router. That's why I asked you to set your router to be Open for a test.
- ooofest
Click to expand...
Click to collapse
I tried WEEP-Open and that did not allow me to connect either. I did set up WPA2 but I still was not able to connect. The power setting was set to 10. Not sure how to manually add the device which I was going to try. I've forgot it several times and added it again but it does not work. I did connect at a different location. Not sure what else to try. Even tried changing the channel.
iLogikk said:
I tried WEEP-Open and that did not allow me to connect either. I did set up WPA2 but I still was not able to connect. The power setting was set to 10. Not sure how to manually add the device which I was going to try. I've forgot it several times and added it again but it does not work. I did connect at a different location. Not sure what else to try. Even tried changing the channel.
Click to expand...
Click to collapse
If it's not connecting to your router with WEP-Open, then something different is going on. I looked in the manual for MAC Address access lists, but that doesn't appear to be a feature of this router (unless it was added in a firmware update which came after the manual was published - if this was the case, your laptops and iDevice would have had their MAC addresses added to the router as another layer of access control to the WiFi network).
Sorry, I'm out of ideas on this one. You seemed to say that the Samsung connects to other WiFi points, so perhaps there is an inherent incompatibility between this router model and your phone which can be reported to Samsung and/or Verizon Tech Support - for all we know, this is a known issue.
- ooofest
ooofest said:
If it's not connecting to your router with WEP-Open, then something different is going on. I looked in the manual for MAC Address access lists, but that doesn't appear to be a feature of this router (unless it was added in a firmware update which came after the manual was published - if this was the case, your laptops and iDevice would have had their MAC addresses added to the router as another layer of access control to the WiFi network).
Sorry, I'm out of ideas on this one. You seemed to say that the Samsung connects to other WiFi points, so perhaps there is an inherent incompatibility between this router model and your phone which can be reported to Samsung and/or Verizon Tech Support - for all we know, this is a known issue.
- ooofest
Click to expand...
Click to collapse
Thank you for all of your help!
Rams99 said:
I had the same issue as you. I would be connected to my router and nothing at all. I am using a att modem/router along with my netgear wndr3800. But wifi was dropping a lot of the time. I never had this problem before when I had my Rezound. 3 days before I got my S3 I upgraded the firmware on my netgear router. I am guessing my S3 didn't like the firmware update or something. I tried everything in the router settings to doing a factory reset on both the att modem and my netgear router. Nothing... So I honestly thought it was my phone. Called Verizon and asked them to ship me a refurbished. So, I thought I would try one more thing. Revert back to my old firmware on the netgear router. Well it worked. Since Friday night I haven't had the issue you are having. Connected to my home wifi with no drops at all. It could be the firmware. Wonder if you could revert back. On a att modem/router I am not sure.
Sent from my Samsung Galaxy S3
Click to expand...
Click to collapse
I've tried every way possible to find a way to revert back but it does not work. No success. I've noticed that this S3, my old razr, & another android phone does not actually connect. The comet (3rd phone) actually appears on the the panel but the ip address on the phone is different than what is showing on the admin page for my router. The phone does show whereas the razr and s3 never even appear in the list though they say they are connected.
I'm at a dead end
iLogikk said:
I've tried every way possible to find a way to revert back but it does not work. No success. I've noticed that this S3, my old razr, & another android phone does not actually connect. The comet (3rd phone) actually appears on the the panel but the ip address on the phone is different than what is showing on the admin page for my router. The phone does show whereas the razr and s3 never even appear in the list though they say they are connected.
I'm at a dead end
Click to expand...
Click to collapse
To be honest. It's not your phone. I think you said you already did a factory reset on the modem/router correct? If not, do it and revert back to factory settings. If that doesn't work I would call att and tell them to send you another att modem/router. Tell them your wifi is down. Hopefully you'll get everything back to where it was. Good luck.
Sent from my Samsung Galaxy S3
Fix
This is what finally worked after two weeks of researching! Found this here for the toshiba thrive but it worked for mr! http://www.thriveforums.org/forum/t...1-thrive-will-not-connect-t-2wire-router.html
I tried this part but all of my settings were already set to match this....including it because it was part of the process.
--------------------------------------------------------------------------------------------------------------------------------------------------------------
Originally Posted by shakefry
My little sister received a cool Toshiba Thrive for Christmas but the thing will not connect to the proprietary router we have. The router isn't the problem because I've been able to connect a Macbook, 2 PCs, a 3DS and a smartphone to it and they all work as needed. When we put in the password for the connection it saying it is 'scanning' and 'connecting' then disconnects and starts going into a scanning loop saying is scanning then stopping then starting again.
I found a similar topic about this but the thread did not answer my question. I followed all of the steps of given solutions to no avail. And the constant suggestion to set the beacon or preamble differently is highly frustrating because the model router I have does not have such settings (I have gone through all the menus about ten times, literally).
I have also heard that the connection security could be a factor but I am not willing to downgrade my WPA 2 (TKIP & AES) to a WPA 1 or WEP, unless its absolutely necessary. I've been googling for hours so I need a solution or unfortunately we will have to return it for a more compatible device, which would suck because we got this for a good price (new).
Our router is a 2WIRE 3800 hgv-b (we have AT&T Uverse, idk if I should specify anything else)
Any help would be greatly appreciated.
Hi shakefry - Nice to meet you. You are 100 percent right you should not lower your security - WPA2 is the strongest and it does work fine with Thrive. That is what I use.
For some reason the ATT 2-wire routers are the most frustrating, but that is not a problem. We just might have to try a few different things, instead of getting it to connect the first time, so stay with me, OK? big brothers always have to help their little sisters...
----
1. You do not have MAC Filtering enabled,do you? If you do add the Thrive's MAC to the Router's list of permitted devices. Then try connecting.....
2. Not using MAC Filtering, or you added the thrive and still can not connect ......
OK, First ... Lets get the info your Windows Laptop has about your router when it connects
successfully to the 3800HG-B Router via wifi:
On your (Win7?) PC that is successfully connected by wifi to the same network, lets get some wifi settings. Vista - pretty much the same screens, XP a little different looking.
Click on the wifi signal lower right taskbar, open network and sharing center.
click on right side in blue, your network name
Pop up window - click on Details
the detail window opens ...
IPv4 Subnet Mask should be 255.255.255.0, if not we need to change it in the router settings.
This would prevent you from getting to the internet, but with all devices not just thrive.
Copy down IPv4 Default Gateway, and both IPv4 Servers
(Most routers will not need the actual IPv4 addresses in the devices DNS1 and DNS2, but yours might)
Now (no picture) close the DETAILS window and click on WIRELESS PROPERTIES. click on SECURITY tab, then click on SHOW PASSWORD. DO NOT CHANGE THIS FIELD, YOUR PC WILL DISCONNECT. WHAT YOU SEE IN THIS FIELD IS THE CORRECT PASSWORD TO YOUR NETWORK.
(I just want to be 100 percent sure - this is the password you need to log the thrive on. You are pretty sharp with all this stuff, so you know it is case sensitive, don't mistake a "zero" for the cap letter O, etc.
We will try using these when we set Thrive's wifi settings for your network.
(Go to link to find the screenshot)
Now please check the following router summary page by logging on to your router.
Make sure, on the right side it, shows enough DHCP Available, and on that the router
address is still 192.168.1.254
And on the left, the page is exactly the same as below, none of the blank fields are filled in, right?
And the top button is still selected ..... 192.168.1.0/255.255.255.0 (default)
--------------------------------------------------------------------------------------------------------------------------------------------------------------
THIS IS WHERE THE ACTUAL FIX CAME IN
Originally Posted by shakefry
"Would it possibly help if i DID enable filtering? then I could just put in all the device's MAC addresses and maybe it'll be more focused or something?"
No filtering wont "pull in" the devices, through the front door of the router. Filtering will just turn them around and kick them out again if they are not on the "invited to the party" List.
"edit: I just found a similar page, the design is slightly different. The router/gateway address is one number above my DHCP range and it says I have 178 available and there are 12 allocated (weird because we only have 10 devices connected to this thing that I know of)
OK so you have plenty of available IP addresses (DHCP). It is normal to see a couple more than the number of devices you have."
So now you have the info you need to connect the thrive (maybe):
1-Hold the Thrive in portrait mode so the keyboard does not hide the settings
...
2- Go to Settings >> Wireless and Networks >> Wi-Fi settings >> tap your network name, Tap FORGET
Now when your network name shows up again under wifi settings ....
select WPA2
Enter password, it is case sensitive.
3- tap the triangle where it says DHCP, select "static"
enter 192.168.1.173. (a nice odd numbered unused ip, away from the auto assigned ones).
(You are making it an odd number (173) because if you buy, in the future, something like a network drive, or AppleTV, it will probably come with a nice "multiple of five" static number like 150 or 155 or 35
the "CONNECT" is greyed out .... right?
4- enter routers gateway 192.168.1.254
enter prefix 24
enter dns1 192.168.1.254
5- the"CONNECT" brightened up again? Tap CONNECT.
....... OR ..........
CONNECT is still greyed out? Enter DNS2 192.168.1.254, tap CONNECT
ARE YOU CONNECTED???
If NO
1- update the router's firmware - try connecting again
2- We will give up on the 3800 and add your second router, with different sets of DHCP ranges, and broadcasting on a non-conflicting channels to the 3800's channel ( channels 1, 6, and 11 do not conflict with each other - assign one router to channel one and the other to channel 11, and keep them a couple of feet away from each other.
shakefry, Please Let us know how it goes, which solution worked ... so other forum readers can help their little sisters too ....
we are standing by (actually in my comfy recliner waiting ..)
Thanks, bobj
aka Bojo, or Obi-Wan, or RouterRooter
I was able to connect to wifi consistently and access the Internet and YouTube app successfully. Hope this helps someone else!!!
Source: http://www.thriveforums.org/forum/t...1-thrive-will-not-connect-t-2wire-router.html
Glad to hear you got it going. I actually fixed mine about 3 days ago. I read somewhere changing your ssid inside the router helps. Well, I did and it actually worked. I haven't had a problem with my wifi signal yet. On mine what was happening also was whenever my phone would go into sleep for say 5min and I went to use the Internet immediately. It would take the wifi about 20-30secs for the wifi to wake up. So far, since changing my ssid I haven't had that problem at all.
Sent from my Samsung Galaxy S3
iLogikk said:
This is what finally worked after two weeks of researching! Found this here for the toshiba thrive but it worked for mr!
. . .
2- Go to Settings >> Wireless and Networks >> Wi-Fi settings >> tap your network name, Tap FORGET
Now when your network name shows up again under wifi settings ....
select WPA2
Enter password, it is case sensitive.
3- tap the triangle where it says DHCP, select "static"
. . .
4- enter routers gateway 192.168.1.254
enter prefix 24
enter dns1 192.168.1.254
5- the"CONNECT" brightened up again? Tap CONNECT.
....... OR ..........
CONNECT is still greyed out? Enter DNS2 192.168.1.254, tap CONNECT
. . .
Source: http://www.thriveforums.org/forum/t...1-thrive-will-not-connect-t-2wire-router.html
Click to expand...
Click to collapse
Thanks for posting a followup.
Did you delete and re-add the WiFi network on your phone, configuring it for a static route and IP address that was in the range on the router, essentially?
- ooofest
Dear XDA members.
I purchased my D820 Nexus 5 a couple of days ago, connected to my home router to set things up but then I noticed something, the device is connected to the router in every single room in the house with at least a fair-strength connection but I actually don't have Internet access unless I'm about 6-10 ft away from the router which is a bother.
Things I tried:
-Restarted router
-Connected to router using other devices
-Edited router settings flipping between 802.11 b/g/n bands
-Changed security type and encryption
-Used a static IP connection instead of a DHCP
-Installed two different roms to test the connection (CM11, Mahdi)
-Installed Wifi analyzer,apk to check surrounding traffic (to avoid wireless interference) and then changed router channel to a suitable one.
I have searched loads of websites and haven't found any working solutions, I'm so desperate for help.
Sorry for writing a long thread and thanks in advance.
Frogi.
In your phone's advanced WiFi settings there is the option to choose between 2.4Ghz or 5Ghz try those. If that doesn't work trying flipping the mobile data switch off and see if that helps.
bblzd said:
In your phone's advanced WiFi settings there is the option to choose between 2.4Ghz or 5Ghz try those. If that doesn't work trying flipping the mobile data switch off and see if that helps.
Click to expand...
Click to collapse
I have tried that, no luck
What happens if you remove any security type and encription?
i am using a router which broadcast both 2.4ghz and 5ghz band using single SSID. how do i force my phone to only allow to connect to the 5Ghz wifi network. i cannot turn off the 2.4ghz band as there are other devices in my house that only support 2.4ghz or do i want to split the bands into 2 SSID.
Thank you.
i was able to split my router to 2 different SSID for both bands
In the past there used to be an option in advanced wifi settings that made the 5GHz "preferred" but Google took it out for some reason.
The disabling of the 2.4 GHz or having 2 separate SSIDs might be the only way right now (not sure for a rooted phone tho)
Sent from nowhere over the air...
Yes not sure why did Google remove that option. Any hidden secret code i.e. *#00*# etc that allowed us to make changes to network setting.
Some routers have band steering which will force devices to 5ghz if supported while keeping 2.4ghz for devices that can't.
Sent from my SM-N986U using Tapatalk
I turned off Auto Connect on my 2.4ghz, so it stays on 5ghz all the time.
Eagle 3 said:
I turned off Auto Connect on my 2.4ghz, so it stays on 5ghz all the time.
Click to expand...
Click to collapse
Mine only 1 ssid for both band. Seem like there is no solution and i had to split the bands into 2 ssid.
angka8 said:
Mine only 1 ssid for both band. Seem like there is no solution and i had to split the bands into 2 ssid.
Click to expand...
Click to collapse
I only have 1 ssid. Like I said, I turned off Auto Connect for 2.4ghz so it always stays on 5ghz.
Eagle 3 said:
I only have 1 ssid. Like I said, I turned off Auto Connect for 2.4ghz so it always stays on 5ghz.
Click to expand...
Click to collapse
thanks, but for me both the bands are broadcast into one SSID. which means i can only find one wifi connection and the wireless router will change the band connection based on the signal strength when i am moving around the house. it will change the connection to 2.4ghz when i am in some place where the 5ghz connection is weak. why i wanted to stay with 5ghz when the connection is weak because it give a much higher download/upload speed compare to the 2.4ghz connection which somehow got much weaker internet speed to the extent of unusable.
angka8 said:
thanks, but for me both the bands are broadcast into one SSID. which means i can only find one wifi connection and the wireless router will change the band connection based on the signal strength when i am moving around the house. it will change the connection to 2.4ghz when i am in some place where the 5ghz connection is weak. why i wanted to stay with 5ghz when the connection is weak because it give a much higher download/upload speed compare to the 2.4ghz connection which somehow got much weaker internet speed to the extent of unusable.
Click to expand...
Click to collapse
Buy a new router where you can separate them and then disable or turn off the 5ghz connection
Looks like this is quite an issue for N2Us. I have a 4 year old iphone and it stays connected to 5GHz in the same place and N2U reverts to 2.4. I have band steering and have been really well on all other devices. Issue lies only with N2U.
Snowleopard1900 said:
Buy a new router where you can separate them and then disable or turn off the 5ghz connection
Click to expand...
Click to collapse
Mine can separate them but since it is only affecting my phone, I hope the change can be on the phone instead. By separating them, I will need to configure all those devices that can only connect to 2.4ghz. e.g. ring peephole
Did you solve issue? Same problem here :/
Eagle 3 said:
I only have 1 ssid. Like I said, I turned off Auto Connect for 2.4ghz so it always stays on 5ghz.
Click to expand...
Click to collapse
Errr...you actually DON'T have one SSID but 2. The band is appended on the name and they are actually 2 different WiFi networks with different names so you could turn off auto-connect on the 2.4GHz one
I use the Wireless Mac Filter on my router to block 2.4Ghz Band for my phone mac address, so the phone can only connect to 5Ghz
If you are using a Samsung phone in the advanced settings for wifi, turn off use randomised MAC address and use the phones actual MAC. This fix has been tested on Netgear routers and works, phone will join the faster 5ghz and still be able to switch to 2.4 if you are at a distance from the router
SenatorDC said:
If you are using a Samsung phone in the advanced settings for wifi, turn off use randomised MAC address and use the phones actual MAC. This fix has been tested on Netgear routers and works, phone will join the faster 5ghz and still be able to switch to 2.4 if you are at a distance from the router
Click to expand...
Click to collapse
Thanks, this worked with Pixel 4a on ruckus WiFi as well!
angka8 said:
i am using a router which broadcast both 2.4ghz and 5ghz band using single SSID. how do i force my phone to only allow to connect to the 5Ghz wifi network. i cannot turn off the 2.4ghz band as there are other devices in my house that only support 2.4ghz or do i want to split the bands into 2 SSID.
Thank you.
Click to expand...
Click to collapse
This is what i did .
(It might give you an very easy option /idea .)
My current setup is a Nokia fibre router that has 2.4 ghz and 5 ghz bands
I bought a reasonable priced wifi mesh 'TP DECO M4 "then
connected it to my fibre router ( ethernet cable )
The TP wifi mesh comes with an Android app fo configure it (settings )
All i did was swicth off the 2.4 ghz band in app, for my TP decom 4 model .
So if i wand to use only 5ghz i connect to my TP DecoM4 ( which is connected to my Nokia fibre router)
My othe devices( that only use 2.4 ghz bands ) i connect dirrectly to my Nokia fibre router, that has 2.4ghz band active ...and also the 5ghz ,
So fo me its a matter of to switch 2.4 ghz on and off in the Android TPlink app .
Hope this give you an very straightforward option ?
good luck
see screenshots below
Hi...
I don't if you already solved you problem but, probably, if you have router which broadcast both band with the same SSID you have option, in router settings, called SMART CONNECT set to the "ON"...
I found a solution that worked for me, i am using a xiaomi router and a s21
Samsung S21 Ultra 5G not connecting to 5Ghz wifi channel
Hi folks . I have a Samsung s21 ultra 5g. I can connect to the 2.4ghz WiFi but more than often I can't seem to connect to the 5ghz wifi channels .I'll have my laptop right infront of me onnected to the 5ghz wifi channel , yet my phone won't be able to the same. My router is netgear nighthawk...
eu.community.samsung.com
"in the settings of your phone / Connections / Wifi / settings of your network put:
IP-DHCP Settings
Phone MAC-MAC address type"
The wife's p7p arrived yesterday. I set it up for her, but I couldn't get it to connect to any of my home networks. The phone tries connecting and then says "Ip configuration failure" under the network name in the network settings. I had to get it setup by hotspotting it to my work iPhone. It connected to that hotspot just fine. I've had other devices like a work laptop not want to connect to my home wifi at times either, so I'm led to believe there is a network issue that different devices don't like at times. The issue comes and goes without any intervention. One day a device won't connect, the next day it will, and I don't have the issue for months.
The 2.4GHz and 5GHz networks all use WPA2 personal security settings. I just changed the 2.4GHz channel to "auto" and the channel width to 20MHz. The 5GHz networks are set to auto with an auto channel width. She left with her phone, so I'll have to see if changing the channel widths mattered, but I'm guessing it still won't connect. I don't know what is wrong or why I'm getting the IP configuration failure error on the p7p. Have you guys seen this with a p7p or other android? What was the remedy? The internet lists all the basic, obvious stuff like reset the router and restart the phone. Not sure what else to do. Will setting a static IP matter?
It's hard to say exactly what could be the issue. But since you mentioned that other devices have had a hard time connecting to your WIFI tells me it's not the phone but something wrong with your router.
Make sure your wireless router(s) have the latest firmware update. Whether your routers need a firmware update or not DO A BACKUP of all the routers settings and do a factory reset of the router...after the reset restore the backed up settings, otherwise you will have to redo all the router settings.
Do a "network" reset on the phone and try to reconnect to the WIFI router after all the router updates/config are finished. Unless you really need it turn OFF 2.4 GHz. Only "older" WIFI items use 2.4. Make sure DHCP is turned on in the router. You can use a static IP but that shouldn't be necessary.
Also, make sure you have an adequate number of free IP's available for dynamic distribution. Check all your DHCP settings on the router. There's no need to reserve, or keep IP's for certain devices UNLESS you are doing something unusual with a device.
jaseman said:
It's hard to say exactly what could be the issue. But since you mentioned that other devices have had a hard time connecting to your WIFI tells me it's not the phone but something wrong with your router.
Make sure your wireless router(s) have the latest firmware update. Whether your routers need a firmware update or not DO A BACKUP of all the routers settings and do a factory reset of the router...after the reset restore the backed up settings, otherwise you will have to redo all the router settings.
Do a "network" reset on the phone and try to reconnect to the WIFI router after all the router updates/config are finished. Unless you really need it turn OFF 2.4 GHz. Only "older" WIFI items use 2.4. Make sure DHCP is turned on in the router. You can use a static IP but that shouldn't be necessary.
Click to expand...
Click to collapse
Older use 2.4? I thought 5GHz is limited in range.
Schroeder09 said:
Older use 2.4? I thought 5GHz is limited in range.
Click to expand...
Click to collapse
Well it depends on how much "range" you need? Your P7P uses 5 GHz.
5GHz should be able to extend everywhere in your house unless you live in a concrete bunker or a palatial estate. 2.4 will penetrate better and farther but you may not have anything that even uses 2.4...so turn it off. Do you need to go out into your (corn field, or the back forty) to receive WIFI? If not, then turn off 2.4
Also, make sure you have an adequate number of free IP's available for dynamic distribution. Check all your DHCP settings on the router. There's no need to reserve, or keep IP's for certain devices UNLESS you are doing something unusual with a device.
Not sure if changing the bands to 20MHz and auto for 2.4GHZ and 5GHz respectively did it or if something "just clicked" but the p7p connects to both now.
Schroeder09 said:
Not sure if changing the bands to 20MHz and auto for 2.4GHZ and 5GHz respectively did it or if something "just clicked" but the p7p connects to both now.
Click to expand...
Click to collapse
Glad to hear you figured it out.