Question Usb Connector connecting/ connector disconnecting. - Samsung Galaxy A53 5G

Hi Everyone,
After 8 hours of unboxing my a53, in facingUsb Connector connecting/ connector disconnecting.
Any suggestions, is it serious problem?

Did you try a different usb cable? And maybe adapter with whatever you're using there.
Different usb port on the other end?
Different computer or whatever?
Its more likely to be with one of those.

Related

RJ11 to Mini USB

I have just purchased a holder for my XDA2 which has a mini USB port on it and I want to connect my TomTom GPS receiver RJ11 connector it.
Does anybody have the same problem or a lead which i can use?
Thanks
if the rj11 connector have all the same connections and signal protocol as usb and maybe even a normal usb connector in the other end then you can buy a normal usb to miniUsb converter
The TomTom reciever has a RJ11 connector and i can not seem to find a converter from RJ11 to anything i.e. USB, Mini USB, etc.
Do you know of any places?
Pratik
well rj11 is a phone connector right ?
and you are sure it's even usb compatible signals running in it ?
i mean if it's analog modem data stuff then converting that signal to something which usb can work with would be a pile of work and end up being more expensive then getting a new gps
True.
RJ11 is a phone connector, but the information from the gps reciever is just being passed to the PDA holder which has a Mini USB connector in it, so I don't think any data conversion is necessary.
The RJ11 has 4 wires in it and the Mini USB has 5, maybe i need to open it up and desolder the mini USB and put in a RJ11 female connector, this then brings me down to pin-out etc.
Do you have any information regarding hte pin-outs?
Pratik
you can get a cable with a mini usb in one end and normal usb in the other if you can get a cable with a mini usb in one end and a female usb in the other then you can connect the usb to xda connector cable that way
of cause that way is way too long but it should make it rather possible to connect the xda to the holder then that is unless
the pda holder and miniUSB connector's signaling require the pda to be a usb host which the xda1 and 2 is not able to be
Maybe we are getting the wires crossed.
The following is a link to the holder
http://www.pdamods.com/proddetail.asp?prod=SPKXDA2&cat=75
The XDA2 sits in the holder just fine and charges at the same time, as it has a connector on the holder, the problem is the GPS connector.
I don't understand your responce to the XDA being a host?
Pratik
RJ-11 to Mini USB Adaptor
I have a pocket, USB Modem at home, and it is RJ-11 on one end, and Mini USB on the other.
Have you tried looking into something like this for a solution?

I need a new retractable charger, any advice?

If I am to get a Galaxy S Phone - or any new phone for that matter - they require Micro USB. I have a bunch of Mini USB accessories. But for some reason, I am having trouble finding Micro USB products. Where can I find some good ones?
Questions include:
Mainly, where should I look to find a good micro USB to USB, for my car?
I occasionally plug my Touch Pro into my TV with my soon to be useless Mini USB to AV Out. What do I do now? I have seen some Headphone To AV Out, do they work?
Micro USB to HDMI? Is that supported across most phones?
What kind of charger does the phone (or most phones) come with? Is it one of those AC Adapters, with the USB plug plugging into the AC Adapter? But the USB Cord is like, one foot? Will I need a regular cable too?
Questions, questions!! So many!!

[Q] micro usb cable help (pinout++)

I bought some really cheap retractable cables of ebay. When I got them they didn't work at all. I opened and rewired the micro-usb connector - the cables were connected all wrong, but after a little soldering I think they're correct.
Now the cables are working fine with my Nokia N82, but when I connect them to my Desire and Desire HD my computer won't recognize it as USB devices, only charging.
I've looked at the pinout here http://www.kineteka.com/microusb-b.aspx - should pin 4 be connected to GND to use it with HTC?
Any tips?
I was curious of the pinout, thanks for the link.
As far as wether the pin should be grounded, well... if it's not working ATM ground it and see if it works? Since you're successfully charging the phone you know you connected the +5 correctly, grounding any other pins won't cause damage...
Cheers
P.S. Also sometimes good to check the obvious, did you enable the Mass-Storage option in Android?
I've had similar issues with USB 1.1 ports.
Are you connecting it to a USB 2 port??

USB-C problem

Charge fonction is working but it interrupts data transfer when I touch the USB-C connector.
Anyone have this problem?
Bad cable. Dirt, dust on C port pins or defective C port.
@blackhawk I tried with two cable which they are in good condition. There is no dust on C port that I clean often with air pressure. I think that possiblity of the defective C port is real but how? I try to care of this phone like my baby. I am disappointed. I will try to contact with Asus but I am sure that they will say this is about user issue.
Bad port on the PC maybe.
2 bad cable aren't unheard of.
Try a otg flashstick and see if it connects ok.
blackhawk said:
Bad port on the PC maybe.
2 bad cable aren't unheard of.
Try a otg flashstick and see if it connects ok.
Click to expand...
Click to collapse
I have tried with two good Usb-c cable on two pc and my car. It stops data transfer when I moved it softly from Usb-c connector (head). I am sure that C port is defective. Thanks for your advices.

Question Teyes cc3 usb problem

Hello,
I recently installed the unit.
Tried to connect usb stick to usb 1 and it didn't recognized it.
Tried port 2 and it burned the usb stick!
Did anyone had this problem?
Is it possible to connect the usb to the wrong place at the back of the unit?
Any help would be most appreciated.
What did seller suggest when contacted for support
I'm going to measure the usb voltage and then contact the seller
Problem solved!
It appears to be that the usb 2 and 3 cable can be connected to the canbus connector.
Replaced to the right connector and the problem solved.
Marik d said:
Problem solved!
It appears to be that the usb 2 and 3 cable can be connected to the canbus connector.
Replaced to the right connector and the problem solved.
Click to expand...
Click to collapse
I have the same problem... but what about USB1??? It still not recognizing the USB stick? And do you have photos of the installation?
From what I understand, the 8 pin (canbus) can be used with the 6 pin (USB 2 and 3) , leaving the right 2 pins alone(unconnected)...
That's because the problem I have is that USB1 does charge my phone but there's no data transfer or recognizing USB stick... debugging off and USB configuration is in TRANSFER DATA.... but USB 2 and 3... when I connect my phone it show the charging logo for about 2 seconds... then... it stops charging, also no data transfer or recognizing the USB stick

Categories

Resources