Hy ewerybody,
i have some charging problem, i fashed a new rom and i cant charge my uni with my travelcharger...prevously it worked with my motorla v3 charger to, but at the moument dont.
i can just charge on usb cabel during active sync, and with my old htc prophet charger....
what heappens, anyone can help me please?
The kind of problem you're describing doesn't seem related to your new Rom, the cables have the same pins (for charging purpouses) connected, chances are that you're travel charger have just gone to heaven just when you flashed your Uni, if you want to be sure (and you do have a multimeter) you can look out for the 5 volts at the mini USB end (be very careful with this procedure as pins are very close to each other), usually (i don't remember it quite well) the power pins are the opposite outer extremes, also the metallic guard is normally connected to ground.
Another thing to verify, is that the travel charger itself is in good working order.
My charger keeps breaking, to be specific the cable.
The cable is very, very poorly designed. It contains 1 wire which is covered by braided shielding. The wire is the positive and the braided shielding negative. At the point where the braided shielding comes together for connecting to the micro adapter the shielding keeps breaking. This means no charging. I have tried soldering couple times but the shielding and wires are so thin it´s just usable a couple of times, until it breaks again.
I tried to make a DIY cable, but i didn´t get it to work. Probably need to place a resistant over some pins, however on the acer micro usb i couldn´t found one on the board where the micro usb is soldered on. Acer didn´t follow the usb standard with this adapter, the wire inside the cable is white, normally this is data instead of positive.
So i´m waiting for the 2nd time for a new 50 euro charger.
Just curious if more people also experienced this problems.
Yeah, I'm on my third charger now. You can charge them through USB although the charging light doesn't show and it takes about two full days to charge from low to 100%.
I have heard, though that a USB 3.0 supplies enough power to charge the a700. Haven't tried it yet, though. It may be cheaper just buying yourself a USB 3.0 PCI card for your PC and charging to that way.
Sent from my A700 using xda app-developers app
I had similar issues where I thought my charger was broken, but it was a thermal problem. It seems, that if the charger keeps plugged into the socket for example over night, it can get so hot that it triggers some thermal protection and switches of. To reset the termal protection, It's not enough to let it cool down (which it does on it's own after shutting down anyway), but I had to unplug it for a couple of minutes, then replug it again - charger working!
I never had an issue with the cable though...
hey im having trouble with my moto g charging it wont charge or anything and ive tried another chager in the house im not sure why its happening
I wouldn't recommend this since it could damage the charger & the phone, but if you squeeze in the middle of the microUSB just enough and then plug it into the phone, it ends up making a connection again. I've tried it on my old S4 a few times; worked with all chargers that wouldn't charge initially.
Hi there !
It sounds like your phone needs RMA , is none of the classic troubleshooting works
Sorry man ,
Please click thumbs up
sticktornado said:
I wouldn't recommend this since it could damage the charger & the phone, but if you squeeze in the middle of the microUSB just enough and then plug it into the phone, it ends up making a connection again. I've tried it on my old S4 a few times; worked with all chargers that wouldn't charge initially.
Click to expand...
Click to collapse
I've done this a lot. I notice the cables just don't stay put after a few months, and squeezing just slightly with a pair of pliers will tighten the male end of the cable and it will grip the female end on the phone better.
Squeezing the charger will work as long as you don't squeeze it too much.
cheers for the suggestions but ive managed to get it charging it just had to be at a slight angle to get it connecting again its still loose in the hole but its charging now im glad cyaogen mod has a setting for the light on the screen to be on when its charging very helpfull
Hello,
For a while now I noticed that when my Xperia XZ phone was plugged in, the metal back of it had a somewhat different feel as if it was textured. Today I decided to test it with a meter to ground to see what the potential was. It delivers a 24 V AC charge when plugged in. It is always delivering 24v and the current is extremely low. This occurred with both the official charger and cable, and an anker charger with anker cable. Does anyone else get this? How on earth would a phone getting a DC charge put out 24V AC?
To test just plug your phone in and lightly drag your finger along the back. Do the same with it unplugged. If your phone is the same as mine you will feel a texture like feeling when it is plugged in, and none when it isn't. I can't see this being a defect as it would have to transform DC somehow to get the AC power. Strangely too my phone now always says that it is providing power as a USB device perhaps that is an issue.
That's common, it's the battery grounding itself via the back metal panel of the phone.
It happens in many phones and usually laptops or tablets, nothing dangerous or defect.
Happened to me once, I reconnected the charger to another socket & it was fixed. Never happend to me ever again.
This phenomenon is called Current leakage, although it might not be hazardous as the current is very low but any sort of leakage could be dangerous.
I would suggest changing the charging socket. If that doesn't work maybe you should try to change the wire & the charger and see if it happens again.
Are you using the original charger? It is likely to happen if the ground pin of the charger is actually not 0V.
Hi, I am a novice in phone repairs though I have successfuly replaced the screen and charging ports on a samsung s6 and note 4.
I am requiring some expert advice on this problem, I was given an XZ from my friend with a cracked screen and charging problem, the charging port became temperamental and failing (at least I think it was that) and eventually wouldn't charge at all. The charging port was handled a bit harshly toward the end, for example the charging cable lifted up and down to try to get a charging response.
Anyway I ordered a screen/digitizer and charging port flex for it, and fitted them, following a guide. Before this, the phone had around 2% charge. After the repair, I switched it back on and conncted the charger, the screen was fine, however there was no response from the charger. The phone then ran flat and eventually ran flat enough to not be able to show the "low charge" symbol when the phone is off. Then after plugging and unplugging the cable (via USB in the pc) it would charge for what seemed a second then stop, the red charging notification light was lighting up. The same happened with a wall charger. I then stripped it back down and back together again. This time there was no response if I remember right, then I connected it to the wall charger and left it for 3 hours or so. I went back to it and it had charged up to 15%.
Now i'm at the point where the phone is working, it's on 90% now, but it charges very slowly, around 60-350 mA per hour on Ampere app. So a full charge is around 12+ hours. This is in the wall socket with a fast charger. Additionally, it takes 10 seconds for the phone to recognise the charger after is is plugged in and that is consistent each time I plug it in. The phone now isn't recognised by my PC via USB, and also won't charge that way also, it just doesn't do anything if I plug it in there. Other than that, the phone works and it holds its charge well.
Any ideas? Thank you.
2 Pics of battery app:
imgur.com/a/YnNtp
pick up an original sony charging cable - no idea why it makes such a difference, but.........
Hi, thanks for the reply, I bought a sony charger but it's still the same, drawing about 50-300 milliamps from wall charger, not recognised by PC and takes 10 secs exactly for the phone to recognise it's being charged. It's just odd how it stopped charging before the "fix", now the new flex lets it charge slowly. Can a battery problem cause this? It still holds its charge well. Maybe this problem is recognisable by some phone repair experts around here? any ideas?
Thanks
Noticed the phone only draws charge from a 3amp charger, anything less isn't recognized. And the power drawn from a 3amp can be 30-1000ma but averages around 300 ma. Can anybody point me to a hardware forum maybe? I can't find any, i guess it need taking to a phone expert but it's gonna end up costing more than its worth with the stuff i have done already.
Aukey Quickcharge 3.0 is working fine. It is cheap too.
I have just purchased a aukey charger, but my XZ seems to be taking longer to charge than the UH20 charger that came with my XZ. Any suggestions guys?
dibdin said:
I have just purchased a aukey charger, but my XZ seems to be taking longer to charge than the UH20 charger that came with my XZ. Any suggestions guys?
Click to expand...
Click to collapse
Buy a UCH20
Sent from my F5321 using XDA-Developers Legacy app
Have you tried cleaning/replacing the charging port itself? As i see, you replaced only the flex cable.
There's probably extremely weak contact somewhere in the charging hardware i think, because you need 3.0 A charger to get any kind of charging response. Weaker current probably gets lost at that 'weak contact'.
Buying new chargers won't fix that if you ask me
I have exactly same problem with you
I am about to buy a new charger, yet I saw your post
At first I thought it was the cable. Then my cable work normal with other phone. So does my charger, it connect perfectly with other phone (xperia xz premium and xiaomi mi5)
It seems that our phoneis the only one who can'y charge normally.
I am quite depressed, also looking for solution. Mind if you share if you have succedeed? Thanks before
---------- Post added at 01:44 AM ---------- Previous post was at 01:25 AM ----------
Try plug in and plug out. My phone sometimes charge a normaxl. But need a lot of effort
Solved
Use the the detect usb in the notification keys before connecting the charger,, this will solve the fast recharging issues
Did you solved problem? I have same issue. Changed battery, usb-flex, no luck
Hi,
I have bought an used XZ.
The owner sold me this phone because he need new battery. I have replaced the old one after a week of test. The old battery works only for 6/10h and drain totally during night even if the phone is turned off. The new one have the same problem. I try to solve with an other battery, and nothing same problem. 12h of standby, after is totally drained. The strange thing is that I have the same battery life even when the phone is turned off, but not only this. If the phone is in 0% he charge without problem. If we have any % of battery I need to connect and disconnect the charger from a wall plug many and many times before he start charging. Phone give me the charge icon for a second and after nothing until I disconnect the charger from a wall plug(I have tested different charger and cable). During my investigation I have found that this phone results every time a little bit hot even if turned off. I have try to disconnect all is possibile, but the heat is from CPU! Now I know that this is the cause of fast discharging in all conditions.
Now I need to know if anyone with a "normal" unit feel the phone heat while turned off and while is on wich temperature have. Mine is every time on 34/35° in standby. Let me know,
thanks
i have same problem . sony xperia xz and sony corp is very very Rubbish
Hi Guys,
I found a way to charge my Xperia XZ with the same loop problem.
Try to push upper volume pad together with power button and plug in the charging cable.
Hold the buttons for 3-5 minutes - you will feel vibrating signals like 3 short and 1 long.
so hold it and then simply leave it for a several minutes and it should start to accept the charge.
Alex Kutikhin
Yes - I had this problem...fixed it by holding in POWER UP and OFF button for 120 seconds.
Do not let go...you will feel vibration (1 short, 3 short). Keep holding for 120 seconds.
Device should now be powered down. Plug in charger cable and leave device off until 100% charged.
Still no fix for the original post’s problem? Having the exact issue with my xzs right now.
lstic said:
Have you tried cleaning/replacing the charging port itself? As i see, you replaced only the flex cable.
There's probably extremely weak contact somewhere in the charging hardware i think, because you need 3.0 A charger to get any kind of charging response. Weaker current probably gets lost at that 'weak contact'.
Buying new chargers won't fix that if you ask me
Click to expand...
Click to collapse
Thanks for the hint...
Old Thread, I know, but I encountered this issue today on an Sony X compact - F5321. Fixed it and want to report back for the next guy.
Same symptoms, noticed first a slow charge, phone was drawing low current and only responding to cable after 10 seconds of plugging in. I than checked for data connection, couldn’t get any. Opened it changed the USB port - BINGO - that fixed the issue, everything working nice.
TLTR: no Solution in Software, it’s a faulty USB-port. change it.
Have a nice day.