Related
Like the title says, I replaced the digitizer, but now my phone either isn't recognizing my SIM card, or somehow the antenna isn't working. I can connect to my home wifi network, I have full audio, full capacitive buttons and vibration....but signal bar just shows empty (i'm using CM10).
I've put my SIM into my other phone, everything works fine. I've checked all of the connectors on the motherboard, everything is connected and nothing is loose or pinched anywhere. Can someone give me a layout of which connections control what?
thanks.
Remember that there's actually two different antennas. My suggestion would be to recheck each connection and make sure there's a solid click when you connect it
Sent from my LG-P999 using xda premium
rtotheichie said:
Remember that there's actually two different antennas. My suggestion would be to recheck each connection and make sure there's a solid click when you connect it
Sent from my LG-P999 using xda premium
Click to expand...
Click to collapse
the top connector came off the wire when I snapped it from the motherboard. I crimped the wire back in place but maybe I sould solder.
Crimp should work if the center pin is still making contact with the wire. Soldering shouldn't hurt anything that I can think of
Sent from my LG-P999 using xda app-developers app
guitarist5122 said:
Crimp should work if the center pin is still making contact with the wire. Soldering shouldn't hurt anything that I can think of
Sent from my LG-P999 using xda app-developers app
Click to expand...
Click to collapse
Update, I've purchased a replacement micro-coax cable, that fits correctly, but still have no signal coming to my phone for whatever reason. Any ideas, maybe getting a crappy g2x for parts and using it's cable?
stevew84 said:
Update, I've purchased a replacement micro-coax cable, that fits correctly, but still have no signal coming to my phone for whatever reason. Any ideas, maybe getting a crappy g2x for parts and using it's cable?
Click to expand...
Click to collapse
Where did you get the cable from?
Did you test the continuity of the cable's wire?
Core Memory said:
Where did you get the cable from?
Did you test the continuity of the cable's wire?
Click to expand...
Click to collapse
This is what I ordered:
http://www.digikey.com/product-search/en?x=12&y=15&lang=en&site=us&KeyWords=A36224-ND
stevew84 said:
This is what I ordered:
http://www.digikey.com/product-search/en?x=12&y=15&lang=en&site=us&KeyWords=A36224-ND
Click to expand...
Click to collapse
That should work. Are all the other internal connectors fully seated?
Core Memory said:
That should work. Are all the other internal connectors fully seated?
Click to expand...
Click to collapse
Yup, not too sure what's happening. I literally did NOTHING else to the phone except accidentally rip off the connection on the lower end of the phone. I still get Wifi, so I know nothing internally is broken. I need to call tmo on the off chance this phone got locked due to previous owner payment or reported lost or stolen. It was an LG branded, g2x, though, which doesn't get sold throught tmo.
stevew84 said:
Yup, not too sure what's happening. I literally did NOTHING else to the phone except accidentally rip off the connection on the lower end of the phone. I still get Wifi, so I know nothing internally is broken. I need to call tmo on the off chance this phone got locked due to previous owner payment or reported lost or stolen. It was an LG branded, g2x, though, which doesn't get sold throught tmo.
Click to expand...
Click to collapse
The LG brand could mean that the digitizer was previously replaced. It sounds like a very peculiar situation you are in. Replacement parts idea is probably best if you have looked over everything very carefully and can't visually find anything wrong. Did you use a hair dryer or other heat source to get the digitizer off? Perhaps the radio portion received to much heat and fried. That the only thing I can think of.
guitarist5122 said:
The LG brand could mean that the digitizer was previously replaced. It sounds like a very peculiar situation you are in. Replacement parts idea is probably best if you have looked over everything very carefully and can't visually find anything wrong. Did you use a hair dryer or other heat source to get the digitizer off? Perhaps the radio portion received to much heat and fried. That the only thing I can think of.
Click to expand...
Click to collapse
When I first did the repair, I ripped the ribbon from mother board to digitizer, not realizing it was there in the first place. The screen separated from the digitizer pretty easily, no heat required.
The new piece I ordered had the digitizer and outside bezel all attached as one piece, which would normally be two pieces. While constructing everything, I forgot that little rubber/plastic piece that fits near the front facing camera, so I detached the mother board connections, then went down to the antenna area and disconnected the micro coax and the connector slipped off the cable altogether. I put the exposed wire back into the connector, restarted the phone, and there has been no signal ever sense.
The last thing I'm going to try is getting an OEM micro coax from either a P990 or P999. I feel kind of stupid for worrying about this, since it's an old phone with limited development at the moment, plus I have another phone already. But since I bought an entirely new shell, I want to fix this damn thing and probably just sell it.
stevew84 said:
Yup, not too sure what's happening. I literally did NOTHING else to the phone except accidentally rip off the connection on the lower end of the phone. I still get Wifi, so I know nothing internally is broken. I need to call tmo on the off chance this phone got locked due to previous owner payment or reported lost or stolen. It was an LG branded, g2x, though, which doesn't get sold throught tmo.
Click to expand...
Click to collapse
Canadian G2X/P999 are branded LG and are known as Optimus 2X even though they are not the P990 Optimus 2X which is/was also sold in Canada, each model sold by different service providers operating on different cell radio bands. At a point, T-Mobile was supplying LG branded G2X/P999 phones as replacements. You probably have one of those or, if you bought it from someone in Canada or who was in Canada that would also explain why yours is branded LG.
If you shorted the antenna cable's internal wire to its shield that would short-circuit the cell radio's output which may have damaged the hardware if the phone transmitted while there was a short-circuit.
Core Memory said:
Canadian G2X/P999 are branded LG and are known as Optimus 2X even though they are not the P990 Optimus 2X which is/was also sold in Canada, each model sold by different service providers operating on different cell radio bands. At a point, T-Mobile was supplying LG branded G2X/P999 phones as replacements. You probably have one of those or, if you bought it from someone in Canada or who was in Canada that would also explain why yours is branded LG.
If you shorted the antenna cable's internal wire to its shield that would short-circuit the cell radio's output which may have damaged the hardware if the phone transmitted while there was a short-circuit.
Click to expand...
Click to collapse
I think what I need to do, if i wanted to keep this phone, is the buy a crappy g2x and use it's internal motherboard with antenna and coax cable.
Does anyone know what the board is called at the bottom of the phone, near the charging port? It's where one end of the micro coax cable connects. The other end is near the middle of the phone, on the main mother board.
I'm wondering since the board at the bottom had the problem, if I were to replace that.
Here's the repair manual:
http://www.scribd.com/doc/84937521/70/EXPLODED-VIEW
There is a way to test the cell phone radio to determine if it works but it involves installing some Qualcomm software, QPST and QXDM, which are professional tools for monitoring, testing and modifying the phone's Qualcomm cell radio characteristics. My post about how to fix the P999 IMEI has the download links and instructions for setting QPST up: http://forum.xda-developers.com/showthread.php?t=1942417 I'll find the QXDM link and installation instructions and post it in this thread too.
Here's QXDM 03.11.36 http://www.mediafire.com/?tmzmngemgmm
Install them both as Administrator.
Core Memory said:
There is a way to test the cell phone radio to determine if it works but it involves installing some Qualcomm software, QPST and QXDM, which are professional tools for monitoring, testing and modifying the phone's Qualcomm cell radio characteristics. My post about how to fix the P999 IMEI has the download links and instructions for setting QPST up: http://forum.xda-developers.com/showthread.php?t=1942417 I'll find the QXDM link and installation instructions and post it in this thread too.
Here's QXDM 03.11.36 http://www.mediafire.com/?tmzmngemgmm
Install them both as Administrator.
Click to expand...
Click to collapse
Awesome, I'll give it a shot when I get home, see what happens.
stevew84 said:
Awesome, I'll give it a shot when I get home, see what happens.
Click to expand...
Click to collapse
I've written up a procedure to determine if a phone's cell radio is working.
http://forum.xda-developers.com/showpost.php?p=33779273&postcount=1
Finally fixed the damn thing, adjusted the length on either side of the mico coax, the cable isn't being pinched anymore so it works fine. I have a slight problem, though, I have some bright light bleeding from the middle left, and top right of the screen. Maybe because the LED isn't seated flush against the digitizer? Is that what would cause this?
It's minimal, and I don't want to take it apart, but still curious.
Around the screen edge there should be attached to the digitizer a thin foam gasket. If it is missing a piece of the thin foam or if it somehow got disturbed or is not there it most likely is where the bleed is comming from.
Eddie
Sent from my AT100 using xda premium
I got a Nexus 5 off a friend for a decent price because he dropped it and bent it up a bit. After giving it a quick look, the only thing that seemed damaged was the black little coax wire that connects the main board to the board on the bottom (Assuming it goes to the antenna), The end simply got bent off. This was an easy fix, replace the cable no worries. The real problem is when I went to go test the phone after I fixed the cable, it doesn't get any cellular signal (Wifi/BT still works), draws a crazy amount of power and the 'Qualcomm WTR1605L' chip specifically gets extremely hot, to the point of overheating in like 30 mins. Rather than tossing a bunch of money into replacement components (or getting another nexus 5 with a bad screen or something) I'd prefer to narrow down the problem to one specific component. This leads to my question:
Does anybody have any ideas to how I can further troubleshoot and diagnose this problem, or knows what the problem exactly is?
I have tried a few things, like if I flash the LG G2 radio (A trick I learned I could do with my Nexus 4/LGOG, after backing up my EFS just in case), Wifi and Bluetooth still work while Cellular, GPS and most of the other sensors do not. This stops the big power draw and overheating issue, but doesn't really do anything to further identify the problem component. I noticed that the modem image could be mounted as vfat and you can mess around with the various parts of the image. I don't know which files do what, so I have thus far left it alone.
I know this seems like an odd question to ask here, half the time I see responses like "Send it into Google/LG and have them fix it for you" but that isn't really applicable in my situation
Also, I know that my SIM is good, it works in my Nexus 4, I know that my ROM isn't a issue, because I have multirom installed and tried many different roms. The Radio image shouldn't be an issue because I had updated the phone from 4.4 to 4.4.4/L Preview since I got it (Using the google images and flashall script). IMEI/Whatever the ESN equivalent shouldn't be bad, my friend had been using it before he dropped it.
Thanks in advanced for any ideas, and sorry for the long and comprehensive almost to a fault thread.
dtalley11 said:
After giving it a quick look, the only thing that seemed damaged was the black little coax wire that connects the main board to the board on the bottom (Assuming it goes to the antenna), The end simply got bent off.
Click to expand...
Click to collapse
Dropping a phone can sometimes cause invisible damage (like BGA solder joints failing). Visual inspection can only tell you so much.
dtalley11 said:
This was an easy fix, replace the cable no worries. The real problem is when I went to go test the phone after I fixed the cable, it doesn't get any cellular signal (Wifi/BT still works), draws a crazy amount of power and the 'Qualcomm WTR1605L' chip specifically gets extremely hot, to the point of overheating in like 30 mins.
Click to expand...
Click to collapse
I used to build small electronic projects when I was a kid. When something overheated like that, 90% of the time it was a short or a the wrong value of component. It's possible the drop caused the antenna connector to short out. Try disconnecting the antenna cable and try again with the stock radio firmware and see if the radio continues to overheat.
(I'm not sure how flashing the radio would prevent overheating, unless the original firmware simply turned up the transmit power in an effort to contact the tower, but that's my first guess and should an easy thing to eliminate).
ScottyPcGuy_03 said:
I used to build small electronic projects when I was a kid. When something overheated like that, 90% of the time it was a short or a the wrong value of component. It's possible the drop caused the antenna connector to short out. Try disconnecting the antenna cable and try again with the stock radio firmware and see if the radio continues to overheat.
Click to expand...
Click to collapse
Thanks for replying! When I get home I will give it a shot and see if it still overheats, then update this with my findings.
If it is overheating then it must hardware issue. Worst case is that the PBC board has a crack somewhere because of the bent. Grab the service manual from the general forum and start mesuring the components to find out where is the problem.
bitdomo said:
If it is overheating then it must hardware issue. Worst case is that the PBC board has a crack somewhere because of the bent. Grab the service manual from the general forum and start mesuring the components to find out where is the problem.
Click to expand...
Click to collapse
Ah, thanks. Something like that should be a sticky. For future reference/making sure we're on the same page, I found the thread here: http://forum.xda-developers.com/google-nexus-5/general/service-manual-d821-t2791303
dtalley11 said:
Ah, thanks. Something like that should be a sticky. For future reference/making sure we're on the same page, I found the thread here: http://forum.xda-developers.com/google-nexus-5/general/service-manual-d821-t2791303
Click to expand...
Click to collapse
Yes that is it.
ScottyPcGuy_03 said:
I used to build small electronic projects when I was a kid. When something overheated like that, 90% of the time it was a short or a the wrong value of component. It's possible the drop caused the antenna connector to short out. Try disconnecting the antenna cable and try again with the stock radio firmware and see if the radio continues to overheat.
(I'm not sure how flashing the radio would prevent overheating, unless the original firmware simply turned up the transmit power in an effort to contact the tower, but that's my first guess and should an easy thing to eliminate).
Click to expand...
Click to collapse
It seems to overheat with our without the antenna cables on the stock radio. I noticed that it still gets warmer than it should with the G2 radio, it just takes a lot longer.
That service manual is really comprehensive but unfortunately, it is going to take me some time to actually get to looking it over closely.
[Q&A] WiFi stuck on turning on; MAC 02:00:00:00:00:00; G2 G3 G4 G5 Nexus5 Nexus 7 etc
Hi!
If you are reading this now, you are probably one of the unlucky fellows who's WiFi (and Bluetooth) stopped functioning, and if so, you are probably deperately searching for a solution/fix. I might have something for you, but first:
*** DISCLAIMER/WARNING ***
You yourself are exclusively responsible for whatever may (or may not) happen to your mobile device, to yourself or others. I am only giving hints/advices here that *MAY* help, but I will not take any responsability, nor will I provide any support, in absolutely *ANY CASE*, including, but not limited to: your problem not being solved or/and your mobile device becoming partially or completely broken. Let me be very clear: If you do anything to your device rendering it useless, destroying it, seriously or fataly injuring you or others, and then come blaming me or/and cry for help, I will point my index finger at you and laugh at you. Period.
If you are a impatient person and want to get straight to the point, jump right to section 6.
Table of Contents
0. Foreword
1. Description of the problem
2. Urgent advice
3. Things that didn't work
4. There is little hope
5. My most obvious advice
6. LET'S GET SERIOUS!
6.a Sellotape / Scotch tape
6.b Refrigerator / Freezer
6.c Oven
0. Foreword
Two or three months ago, one fine morning, the WiFi/BT of my LG G2 suddenly stopped working. Initially I thought this would be only one stupid annoying minor thingy, that I’d be able to solve it fast. I was wrong.
1. Description of the problem
When turning on the WiFi, it would just stay in "Turning on..." forever. Similar thing for Bluetooth: It would stay on for a few seconds and then turn itself off again after. (But then, who needs Bluetooth anyway, WiFi ist probably 100 times more important...). I have thoroughly searched the internet, and I found quite some videos with exactly the same problem (remove the two blanks from the links to watch):
h ttps://w ww.youtube.com/watch?v=fRGnQz1zUmw
h ttps://w ww.youtube.com/watch?v=4W8YJMDFM88
h ttp://w ww.dailymotion.com/video/x2cuyjt_nexus-5-turning-wifi-on-frozen-problem_tech
2. Urgent advice
I want to prevent you from wasting countless hours searching for a solution - I wasted so much of my time already, no need for you to repeat that. Therefore: *Please* be aware that there is a VERY HIGH PROBABILITY that this issue is being caused by a hardware defect. I can not speak for all devices of course, but keep in mind that the main reason I wasted so much time, was me beliving it was some software issue! See the next section for a glimpse of stuff I have tried without any success:
3. Things that *DIDN'T* work
01. Restarting WiFi/Bluetooth several times
02. Rebooting the phone
03. Turning airplane mode on/off several times
04. Slapping/hitting the phone (this was indeed suggested in a forum)
05. Using WiFi-Fixer apps
06. Resetting to factory settings
07. Upgrading to newest Android version
08. Fully drained the battery and left it uncharged for several hours
(Rooted the phone)
09. Deleting the /data/misc/wifi/wpa_supplicant.conf
10. Deleting the whole /data/misc/wifi folder
11. Creating a file named ".bdaddr" in /persist/bluetooth containing a MAC-Address in hexadecimal format
12. Creating a file named ".macaddr" in /persist/wifi containing a MAC-Address in hexadecimal format
13. Flashing several custom ROMs to it (CyanogenMod, ParanoidAndroid, ...)
14. Going back to stock ROM
15. etc. etc. etc.
16. Several combinations and permutations of the above
4. There is little hope
Again, as the cause of the problem is most likely a hardware issue, I don't recommend going through all the steps as described in the previous section; however, though none of the steps worked for me, this doesn't mean that none won't work for you neither; you might be luckier than I was. In that case, enjoy your restored WiFi and be happy.
5. My most obvious advice
You need to replace the motherboard (main board) of your device.
Honestly, if you can afford it and it doesn't cause too many inconveniences to you, you'll be better off by simply buying a new device. If you don't want to buy a new device, send it in for repairs. If you don't want to do that as well, you'll have to fallback to a DIY solution:
I. Buy a new main board for your device. Be careful to get exactly the right component for your specific model. If you dont find any shop selling those, there are plenty of individuals out there that own devices with broken displays. You dont need the displays, you need the motherboard. Buy one such broken device, and you'll have your main board replacement.
II. Replace your main board or let someone else do it for you
Continues below.
continuation
6. LET'S GET SERIOUS!
If you are reading this, you either didn't read or you decided not to follow my most obvious advice in section 5. So be it. If you want to carry on from here, be sure to re-read my disclaimer at the top of my post.
There are 3 DIY possible fixes for the WiFi problem - none is guaranteed. I will describe them from the most harmless to the most kamikaze/deadliest. All of them will require you to open your device; if you are not careful and damage any of the components inside, you will end up with a worse device than before - but hey, don't say I didn't warn you.
At this point we assume that the cause of the problem is a faulty solder joint of your WiFi IC. The goal is to try to restore that solder joint. To do that, you will have to:
I. Open your device
II. Find your main board and separate it from all connected plugs
III. Find / identify the WiFi IC chip on the main board. I recommend searching for a service manual for your device, or/and searching for a disassembly video for your device; you need to know which one of the chips on the main board is the WiFi one.
Once you have identified your WiFi chip, you have 3 options, which you may combine with each other, but I recommend to try them out one-by-one as follows:
6.a Sellotape / Scotch tape
You need to make sure that your WiFi chip is pressed against the main board (ideally, this ensures the broken contacts touch each other, solving the problem). The best way to achieve this, is to attach a series of tape strips on the top of the WiFi chip, causing it to be pressed against the main board by the surrounding cover/hull once you reassemble/close the device. The tape strips are just a suggestion, do whatever you find convenient as long as you ensure that the chip is pushed against the board at all times.
This method may solve the WiFi problem already. When you turn your device back on, give it some time (5-10 minutes) and reboot it a few times if the problem still persists. My own WiFi didn't function right away, but after a while it finally recovered - hurray!
6.b Refrigerator / Freezer
Instead of using the tape as described in 6.a, you may first try to put your motherboard in a fridge for a few hours/days. But make sure to put it there in a plastic bag, and avoid moisture as much as you can, specially when taking it out of the fridge. Make sure its completely dry before reassembling your device!
By the way, try the refrigerator option BEFORE you try the freezer option!
6.c Oven
If everything else fails, the oven might be your last chance. This is not a joke, but as you probably can assume, it is "All-In" i.e. highly risky. The theory behind this is that high temperature will cause defective solder joints to reflow, reconnecting and thus fixing the problem.
You should only try this as a matter of last ressort. Be warned that you may fully destroy your main board, and there is a high chance that you will. Also, you may cause serious injury to yourself or others. Make sure you make backups of your data first. DO NOT BAKE THE WHOLE DEVICE, ONLY THE MAIN BOARD. DO NOT BAKE THE BATTERY!!
If you are still reading:
I. pre-heat your oven to 385° Fahrenheit (196° Celsius)
II. put your main board in the oven, bake it there for 7 minutes
III. remove from the oven, let it cool down until every component of the board has room temperature
Finally, here is a video of a guy doing a similar thing, but with a heat gun:
h ttps://w ww.youtube.com/watch?v=A4n0j3uaS7E
Ok, this is all, I hope I could help you.
Good luck!
Summary
Hello all,
first of all, I want to thank brysclar and xbing6 for their valuable feedback! Thanks a lot guys! :good:
Now, in an effort to update this thread and in an effort of trying to summarize it in fewer words (my disclaimer above applies!):
- The described problem seems to affect mainly (all kinds of) LG devices
- The issue seems to be caused by a defective soldering of the Wi-Fi chip on the main board
- The defect seems to be induced by dropping or/and overheating the device; recharging the battery, big/long app or android updates or the flashing of custom roms could cause excessive heating
- brysclar pointed out that replacing the battery might solve the problem (I haven't tried this out myself, so I can neither deny nor confirm this)
- My recommended solution is 6.a - applying pressure on the Wi-Fi chip, pushing it against the main board, using tape stripes
- There is a video of a brasilean guy doing some similar, but using pieces of an old credit card instead of tape strips: https://www.youtube.com/watch?v=OJkdva2iOag BUT PLEASE NOTE THAT HE IS APPLYING THE PRESSURE ON A RANDOM SPOT, NOT DIRECTLY TO THE WIFI CHIP! It *may* work for you, but if it doesn't, find/identify your Wi-Fi chip and apply the pressure there
- If everything else fails, and only as a matter of last ressort, you may try what I have written in 6.c
So... this thread has over 500 views, but not one single reply.
Guys... what has your experience been? Have you tried anything out from the posts above, and if so, what was the result? Did it help you? Do you recommend anything? Has something else, not written here, worked for you?
There are a lot of people out there having the same problem. It would be great if you could give any feedback, share anything that helps the community.
Click to expand...
Click to collapse
I honestly didn't see this post before. You really covered every detail very well. So far, returning my G3 to stock and replacing the battery has fixed it for me. Weird. I know. I did try 90% of the things on your "things that don't work" list and you are correct. They don't work.
wlanmac 02/00/00/00/00, Bluetooth is OK
Hey, i just got an LG LS990 with same Wifi issue and i'm ready to try so WITNESS ME!
Thanks for an amazing and detailed post lml
Simply awesome.
I have similar issue with my Nexus 5x. It is QCA6174 hw 3.2 chip, lspci does not detect this chip any more. I am going to do a little bit investigation from device driver (cnss) perspective. It enables one GPIO to provide power to this WiFi chip, I will try read back this GPIO status to see if it is enabled. I do not have the schematics, I do not know how to check if power is supplied to this wifi chip.
lspci used to show below:
$ ./lspci
00:00.0 PCI bridge: Airgo Networks Inc Device 0300 (rev ff)
01:00.0 Network controller: Atheros Communications Inc. Device 003e (rev ff) (this is qca6174)
If kernel driver investigation does not reveal anything helpful, I will ask other guys to replace the chip.
I thought it is because of vendor partition is accidentally wiped out, maybe it is unlikely.
---------- Post added at 08:49 PM ---------- Previous post was at 08:40 PM ----------
As Bluetooth can not be turned either, I am tending to think this is hardware related as well. As described previously, I will see if I can check that gpio status.
investigating
xbing6 said:
I have similar issue with my Nexus 5x.
(...)
I am going to do a little bit investigation
Click to expand...
Click to collapse
Hi xbing, and thank you for your feedback! :good:
I am really curious and looking forward to hear the results of your investigation! I believe that in your case, too, the Wi-Fi/BT chip is not being supplied correctly due to a defective soldering. Note that I don't think that the chip itself is defective, only the contacts between the chip and the main board. So, before replacing the chip, I'd recommend to first try what I've written in 6.a (or check my update/summary above).
Keep us posted about everything you find out!
Sprint declined to fix my LS990 due to "water damage" being the reason for it not working, and wanted to charge me a $150 deductible for a $100 phone. Shimming the WiFi chip against the metal covering with some thermal pad I had lying around and adding a bit of sticky foam on top of the ribbon cable for the camera worked great! Much thanks!
Tomcat5 said:
Sprint declined to fix my LS990 due to "water damage" being the reason for it not working, and wanted to charge me a $150 deductible for a $100 phone. Shimming the WiFi chip against the metal covering with some thermal pad I had lying around and adding a bit of sticky foam on top of the ribbon cable for the camera worked great! Much thanks!
Click to expand...
Click to collapse
Any idea if thermal paste/grease could work?
unlikely
NavHur said:
Any idea if thermal paste/grease could work?
Click to expand...
Click to collapse
Hi NavHur,
since the problem is mostly caused by a loose Wi-Fi chip, respectively a defective solder joint, using thermal paste or grease is unlikely to help; again, what you need to do is to have your Wi-Fi chip pushed against your main board. You can use your imagination on how to accomplish this; what Tomcat5 described he did ultimately led to exactly having his chip being pressed against the board.
Of course you are free to try whatever you want - if you find new solutions please post some feedback.
Good luck.
NimbleWeasel said:
Hi NavHur,
since the problem is mostly caused by a loose Wi-Fi chip, respectively a defective solder joint, using thermal paste or grease is unlikely to help; again, what you need to do is to have your Wi-Fi chip pushed against your main board. You can use your imagination on how to accomplish this; what Tomcat5 described he did ultimately led to exactly having his chip being pressed against the board.
Of course you are free to try whatever you want - if you find new solutions please post some feedback.
Good luck.
Click to expand...
Click to collapse
Thanks you so much, I placed a small piece of plastic above the wifi chip and one next to the camera lens. Now the wifi works fine. However my screen was pushed up so it bended a little. The faulty thing was my battery, not the added plastic. I compared mine with the one of a friend, mine was 1 mm bigger. (also with the battery of my friend's g3 the screen was fine)
I'll be changing it soon.
same problem as u but sometimes wifi works(mainly fully charged) and sometimes dont
i have lg g2 D802 model. It had a wifi problem as u shown in your videos,my phone also behaves same like yours but sometimes it works normally like while charging,works like 2 or 3 times a day(for 5-10 min).please tell me whether my phone got ic problem or software issue
Pratap94 said:
i have lg g2 D802 model. It had a wifi problem as u shown in your videos,my phone also behaves same like yours but sometimes it works normally like while charging,works like 2 or 3 times a day(for 5-10 min).please tell me whether my phone got ic problem or software issue
Click to expand...
Click to collapse
Hi Pratap94,
nobody, neither here in this forum nor elsewhere in the internet, will be able to give you a reliable answer without having a *physical* look at your phone. Nobody.
However, I can give you my opinion, based on the stuff you wrote: The fact that it works normally sometimes, specially while charging (probably it heats up in the process?), indeed seems to indicate a hardware issue. I believe you have a loose Wi-Fi chip i.e. a defective solder joint, like I had on my LG G2 D802 as well. I solved my problem by doing the stuff I described in 6.a.
Good luck.
Thank you so much
NimbleWeasel said:
Hello all,
first of all, I want to thank brysclar and xbing6 for their valuable feedback! Thanks a lot guys! :good:
Problem solved good bless you!! the problem is fix in that youtube video XD
Click to expand...
Click to collapse
Sadly step 6.a did not help me. Well, it worked for first 5-10 minutes and then back again.
Olzhas18 said:
Sadly step 6.a did not help me. Well, it worked for first 5-10 minutes and then back again.
Click to expand...
Click to collapse
Hi Olzhas18,
that might be an indication that your WiFi chip is still a bit loose and is not sitting tight enough on the main board. On LG G2, it is difficult to push the chip against the board because it's covered by a metal cover...
Also, did you check out this video: https://www.youtube.com/watch?v=OJkdva2iOag ?
Good luck!
NimbleWeasel said:
Hi Olzhas18,
that might be an indication that your WiFi chip is still a bit loose and is not sitting tight enough on the main board. On LG G2, it is difficult to push the chip against the board because it's covered by a metal cover...
Also, did you check out this video: https://www.youtube.com/watch?v=OJkdva2iOag ?
Good luck!
Click to expand...
Click to collapse
Thank you this tip and this whole thread. I have seen this video, but still the same effect. 5-10 minutes, I can rean some news and back to flashing. I'm going to buy Huawei Honor 8 soon, it was the last chance to recover my G4. I doubt I will purchase any other phone from LG.
Same boat
But bluetooth working
In cm roms also wifi tethring can be onn
But u cnt turn onn wifi
I had the same issue, can't turn on Wifi after factory reset.
I turn off my device off after one hour and reboot wifi was OK but when I want to upgrade some apps iwifi turn of again and my phone reboot with no SIM card.
I do "6.a Sellotape / Scotch tape" + a creedit card cut with this video https://www.youtube.com/watch?v=6_0jzp65eLY#t=73.319872
My LG G2 works fine
I have a problem with my s7 G930F, wifi and moble hotspot are not working at all, when i turn on wifi or hotspot it just showing turning on ..
and when i turn on bluetooth it works for 5 seconds and then keeps switching off and on after every 5 seconds
i tried to wipe cache, factory reset, return to stock rom, install custom roms, install latest modem and bootloader but that did not fix the problem.
please help !!!
Does your gps works ?
NeoDJW said:
Does your gps works ?
Click to expand...
Click to collapse
Yes it's.
NeoDJW said:
Does your gps works ?
Click to expand...
Click to collapse
Yes it works.
Check water sticker on botton of sim slot
I had the same issue with a board i fitted to G930F bluetooth wasnt working nor wifi for no apparent reason i went through absolute everything firmware wise and system wise and couldnt figure out what the problem was i then removed everything once again looking for a loose connection it turns out the board i fitted in the top right hand corner there is a silver chip that controls wifi and bluetooth under the antenna there was a small black spot i noticed once carefully cleaned up i found the culprit there are 2 tiny fuses that blew conecting to the wifi chip this chip must also control bluetooth and NFC as that no longer works also.
Martty
Do you find a solution
daliyoos said:
Martty
Do you find a solution
Click to expand...
Click to collapse
I did find the solution unfortunately it requires the wifi ic chip to be replaced along with the fuses accompanied to the chip on the logic board but that means micro soldering the new chip on the other solution is change the board out when you take the antenna at the top off at the top right is the silver chip look at the circuitry and you should find a black burnt out spot also check the aerial for plastic burn where the chip sits
Thats the only solution available that ive found, not even the factory binary found the issue with the hardware though
That one chip though controls the wifi/bluetooth/android hostspot/NFC funnily enough though even though its blown visually the wifi toggles on still and will every now and then pick a network up for a second, the bluetooth toggles on but will not find any other device and other devices cannot find it either, the android hotspot turns on and broadcasts a signal but when trying to connect to it it will not connect, the NFC toggle is also set to on with the writing and toggle greyed out and NFC apps asking to turn on the chip but it cannot be toggled these are symptoms of the error,
If you would like to inspect your device,
If you dont know what your doing order a new backing i can successfully remove them without cracking them with a hair dryer, screen puller the cheap ****ty ring ones, and a guitar pick,
To start heat the backing of the phone up with hair dryer until its warm/hot next step is my secret trick to pop the watertight seal take the sim tray out and no **** blow into it youll hear the seal break get the ring puller pull it up enough to get the guitar pick in and just slide it all the way round,
Once the backs off theres 3 screws at top on antenna your gonna wanna use a phillips #00 for them once the screws are out get a pair of tweezers and slide them into the slot on the left side of the antenna where the vibrator is and pull up it will probably go flying if you use to much force but it wont break, the circuit and wifi module are now exposed on the top right diagnose the board for burnt spots if there is there, take the NFC chip off below the antenna and then the speaker to expose the charging port check the bottom right hand corner for circuitry burning also.
Matty1993 said:
I did find the solution unfortunately it requires the wifi ic chip to be replaced .
Click to expand...
Click to collapse
Hi, I have same problem for long, I tried all software options: factory reset, network reset, hard reset, wipe, firmware upgrade, downgrade,,
I can use NFC without problem but WiFI and Bluetooth are greyed out or stucking on turn on without finding anything.
Could you confirm what is the right IC for it ? I found two different IC number one on Ebay another on Part4reparirs , not sure which one is legit as both claim to be G930 wifi-IC (can't add link as I am new user)
also I would be interested to know where to buy fuse for it
I really miss my phone for few month using spare xiaomi now
aminkian said:
Hi, I have same problem for long, I tried all software options: factory reset, network reset, hard reset, wipe, firmware upgrade, downgrade,,
I can use NFC without problem but WiFI and Bluetooth are greyed out or stucking on turn on without finding anything.
Could you confirm what is the right IC for it ? I found two different IC number one on Ebay another on Part4reparirs , not sure which one is legit as both claim to be G930 wifi-IC (can't add link as I am new user)
also I would be interested to know where to buy fuse for it
I really miss my phone for few month using spare xiaomi now
Click to expand...
Click to collapse
Hey mate im a phone technician,
Ive got a few boards qnd broken S7 laying around ill pull one down and take a picture and label it and what not & will post it here for you,
The ic chip isn't actually a fuse its an actual chip which controls the wifi and bluetooth functions of the phone NFC is locted on 2 different part of the board aswell as wireless charging coil etc, so if that stuffed best of getting a new board, but however there is a small thermistor (ThermalTransistor) just before the wifi bluetooth ic hopefully for you its blown that and stopped current before getting to the wifi ic, i will also label this in the diagram
Hopefully in your case its the thermistor youll know anyway if it is will be blown with black or white residue everywhere and your antenna may be partially burnt out in that case, you will also need to check the daughter board for black or white burn residues also in the bottom right hand corner ill take a picture and label again also,
If i cant get the pics up straight away for you its because xda app is being a pain in the ass still and wont let me upload being playing up for a week now
Matty1993 said:
Hey mate im a phone technician,
Click to expand...
Click to collapse
Thanks for reply,, based on your explanation still other thing like antenna fuse thermistor could be damaged and ordering them one by one + shipping is not good idea.. I may better find cheap broken LCD S7 and ask technician to swap the board for me.
still looking forward to the pics... my Insta Gram acc is [at]kian.moments :fingers-crossed:
Hey everyone,
recently my SC-02h (Jap Docomo version) hard-bricked and has no way to recover besides JTAG or motherboard replacement.
This made me think of an experiment.
Can you replace any motherboard (which includes all chips and the storage) with another.
I ordered the g935FD dual sim version with the Exynos chip, this compared to my QC single sim version which is currently bricked.
Hopefully within the next few days I'll receive the motherboard and start the replacement process (I will probable film it) to see if it works.
If so, anyone could replace their motherboard by a new one that is unlocked or has a different chipset.
Please discuss here if you're also interested in changing your own mobo with another.
Can't see why it won't work as the motherboard is what determines the model. Just make sure you order up a dual SIM tray too.
Motherboards from different chipsets *may* have different connections on how things wire up. I'm not saying they do, I'm just thinking out loud. I'd only buy a replacement motherboard from the same variant.
And good luck finding a new motherboard. At the price they sell for, you'd be better off buying a whole new phone.
Would like to see how this goes. Please record the process.
Sent from my SM-G935T using Tapatalk
lyriquidperfection said:
Can't see why it won't work as the motherboard is what determines the model. Just make sure you order up a dual SIM tray too.
Click to expand...
Click to collapse
Yea I ordered that one, although I thought the tray looks the same (bottom part), so until my new one arrives I'll use the older one.
the_scotsman said:
Motherboards from different chipsets *may* have different connections on how things wire up. I'm not saying they do, I'm just thinking out loud. I'd only buy a replacement motherboard from the same variant.
And good luck finding a new motherboard. At the price they sell for, you'd be better off buying a whole new phone.
Click to expand...
Click to collapse
I checked the connections and they are the same, the only thing that differs is the sim holder and the chipset.
Also a new phone (unlocked) costs at least 2,5times more (live in Japan).
dogredwing1 said:
Would like to see how this goes. Please record the process.
Sent from my SM-G935T using Tapatalk
Click to expand...
Click to collapse
I'll record it on video as soon as it arrives, also the process of taking it out and replacing it completely. So if it ends up in failure you can all see it.
In what way is it bricked? The S7 is almost impossible to brick.
CuBz90 said:
In what way is it bricked? The S7 is almost impossible to brick.
Click to expand...
Click to collapse
Hmm I flashed a rom with TWRP, (lineage, but wrong build) after that I rebooted and the phone stopped responding completely.
So black screen, no led when charging, no response at all when pressing buttons.
Even disconnecting battery and reconnecting didn't work.
Also no recognition in windows when connected to USB
totalvamp said:
Hmm I flashed a rom with TWRP, (lineage, but wrong build) after that I rebooted and the phone stopped responding completely.
So black screen, no led when charging, no response at all when pressing buttons.
Even disconnecting battery and reconnecting didn't work.
Click to expand...
Click to collapse
Can't get to download mode?
CuBz90 said:
Can't get to download mode?
Click to expand...
Click to collapse
Well if I could I wouldn't be ordering a new MoBo
Even made a USB JIG
Another thing you might lose is waterproofness. I cracked my screen badly and instead of repairing it at a 3rd party shop, I sold it and got a new one. Coz it won't be waterproof anymore..
thedisturbedone said:
Another thing you might lose is waterproofness. I cracked my screen badly and instead of repairing it at a 3rd party shop, I sold it and got a new one. Coz it won't be waterproof anymore..
Click to expand...
Click to collapse
i should be fine, just get it glued back together properly.
besides i don't really care about it.
Unless the other components (camera, vibrator motor, various sensors, OLED Panel etc.) don't differ in the way they talk to the mainboard, I don't see why it shouldn't work. As others have said, I'd really love to see how it'll work out for you. So, thanks for sharing =)
Well it didn't work out, I put in the new motherboard but the phone didn't power on at all. There is also no led when trying to charge it. I'll be sending it back to the supplier and buy another version instead.
https://www.youtube.com/watch?v=jym2aNwRmkc
Made a video of the process and failure
totalvamp said:
https://www.youtube.com/watch?v=jym2aNwRmkc
Made a video of the process and failure
Click to expand...
Click to collapse
Was interesting to watch, however you only tried powering on twice and quit?
Connecting a charger had no effect?
Unless the board your received was dead to begin with.
totalvamp said:
https://www.youtube.com/watch?v=jym2aNwRmkc
Made a video of the process and failure
Click to expand...
Click to collapse
Can you share the link of where you bought the motherboard? It might be that you bought a blank motherboard. In that case you want it to be flashed with the correct IMEI and partition (table?). AFAIK the IMEI has to be that of your previous phone since you can't just "create" a new IMEI. Don't even want to get into the legal repercussions but here's a sneak peak; in some countries it's a criminal offence to alter an IMEI or even have tools to alter IMEI. Don't quote me on this and I'm asking the community to correct me. If the motherboard comes from a previously active device, it should have its own IMEI and none of what I said before matters.
Whatever, none of that necessarily explain why it didn't boot up. Have you tried charging and plugging it to a PC? If it isn't dead, your PC should at least detect A device.
murtaza02 said:
Was interesting to watch, however you only tried powering on twice and quit?
Connecting a charger had no effect?
Unless the board your received was dead to begin with.
Click to expand...
Click to collapse
Well I tried a few times after that and after letting it on a charger, still no response.
nitrous² said:
Can you share the link of where you bought the motherboard? It might be that you bought a blank motherboard. In that case you want it to be flashed with the correct IMEI and partition (table?). AFAIK the IMEI has to be that of your previous phone since you can't just "create" a new IMEI. Don't even want to get into the legal repercussions but here's a sneak peak; in some countries it's a criminal offence to alter an IMEI or even have tools to alter IMEI. Don't quote me on this and I'm asking the community to correct me. If the motherboard comes from a previously active device, it should have its own IMEI and none of what I said before matters.
Whatever, none of that necessarily explain why it didn't boot up. Have you tried charging and plugging it to a PC? If it isn't dead, your PC should at least detect A device.
Click to expand...
Click to collapse
http://www.ebay.com/itm/MAIN-MOTHER.../182310990269?ssPageName=ADME:X:RRNTB:NL:3160
It should be one with an IMEI how else can it be unlocked.
I tried plugging it in as well, but my PC doesn't recognise it at all.
I've ordered a different one this time, this motherboard was also slightly different from the one I had (2 cables instead of 3) so it might be incompatible.
I ordered this one now: https://www.aliexpress.com/snapshot/0.html?orderId=82116420384467&productId=32737224430
Did you end up having any luck with the second motherboard?
Or has anyone else attempted this before?
I'm looking to swap my qc chip for the exynos.
How was the operation??
Hello i'm interested to know how was the experiment becouse i wanna try almost the same thing, i have a s7 sm935fd and i wanna change the motherboard for a sm935f model. Please answer me!
I am also going to try swapping motherboards. How did yours work out?
Hi @totalvamp,
I am going to try swapping out a good motherboard from a banged up sprint G930P phone with a clean IMEI into a clean, whole, G930X demo model that I picked up cheap on Ebay.
The "X" demo phones work on WIFI only. I understand that the "X" motherboards are missing the cellular radios, which is why I am trying this swap -- it should be far easier and less costly than doing a full screen&LCD replacement, which requires tearing down the entire phone, and costs about $150. Hopefullly, I will just have to remove the back, the QI receiver and I think the camera, and I'll get access to the motherboard.
My hope is that all the rest of the parts are present -- we'll see how it goes.
I look forward to hearing from you.
Philip