I unlocked the bootloader through mi unlock tool. I flashed official twrp from their site, 3.3.1-0-violet.img but when I tried booting it into recovery, it got stuck at twrp logo. Then I learnt that it's necessary to wipe userdata using fastboot first so I did that. Then, when twrp started, it was unable to install/wipe/mount any partition. Tried installing magisk using sideload, did work but then device stopped booting.
Figured out a way on how to fix the mount issue, twrp working fine, but then I accidentally wiped /system. Now my device only opens in fastboot, even though I've tried installing, erasing and reinstalling that twrp recovery as well as a couple of others I found in pixel experience forums for my device.
I've got all the stuff needed to install pixel experience, fcrypto disabler, xiaomi latest firmware and the rom itself. Can anyone guide me on how to install it using fastboot?
Also whenever I try booting the recovery image straight from fastboot, it says that command failed, too many links.
I can't boot into recovery via vol up + power button, fastboot doesn't recognize command fastboot reboot recovery.
you need to install stock rom ,then flash twrp but newer unofficial twrp and orangefox twrp boots into recovery even if system partition is empty.
try installing unofficial twrp or orangefox.
orangefox is recommended .
Hi everyone,
I've been trying to get TWRP to stick for a while now, but still haven't been able to get it to install. A while ago I managed to flash Resurrection Remix using Lineage recovery which does work, but since Lineage recovery is quite limited, I really wanted to get TWRP to work. Since TWRP 3.5.0 released yesterday, I gave it another shot hoping that they fixed the issue, to no success.
I can get into TWRP just fine by temp booting it with fastboot, but after flashing the installer zip, any recovery that was previously installed gets wiped and the device will reboot when trying to get into recovery. I can still boot my phone otherwise.
The steps I took to get to this point:
Unlocked bootloader
fastboot boot twrp.img
Decrypt using screen pattern (successfully)
Flashed twrp installer zip (no error messages, process finishes successfully)
Reboot into recovery (both from twrp and bootloader at a later point)
Things I've tried:
Use a different TWRP version. Same problem as described above on both 3.4.x and 3.5.x, can't get it to decrypt on lower versions due to Android 10.
Install to recovery ramdisk, this just breaks things even more, probably because it's an A/B device?
Try a different recovery. Lineage recovery works just fine, but it's very very limited. Would really like to get TWRP working.
Trying to flash the zip results in no error messages, but any previously installed recovery gets wiped and magisk is uninstalled, which leads me to believe that it has done at least something to the boot img.
Thank you in advance.
EDIT 25.02.2021:
- Attached TWRP log
EDIT 12.03.2021:
- Log didn't want to attach, they can be found here: https://pastebin.com/awnhHDBU
Same question here. It seems that you can only boot from TWRP, not install it.
Tried installing again today, to no avail. However, I was smart enough to save the log this time. I have attached it to the main post, would be much appreciated if someone could check it out.
Hello everyone sorry i'm new here and also i don't know much about rooting my device Poco X 3 pro MIUI 13.0.3 Global and Andriod 12 .. sadly i messed up i had my boatloader unlocked fo my Poco x3 pro and i have installed custom recovery TWRP then i tried to install Magisk via the TWRP recovery but it won't work mainly because the data is encrypted and the TWRP can't acess in the internal storage so i used a OTG usb but gets error unable to mount /data/media/fox/.fox note that i tried both Orangefox and twrp still same error i assume its because the device is encrypted . also decrypt doesnt work it ask for password and i even removed all my accounts and disabled all lock screen but still not working at this point i thought that downgrading from MIUI 13 to 12 will fix this since i saw all videos who had it working used MIUI 12 and here where i messed up i used XiaoMiTool V2 then clicked custom ROM and used an offecial ROM from Xiaomi website ( miui_VAYUGlobal_V12.0.6.0.RJUMIXM_eccd7da42b_11.0.zip ) the phone booted into TWRP and started installing but ofcourse got the error first unable to mount /data/media/twrp then the process continued installing all the files then phone rebooted into TWRP LOOP now im stuck into TWRP and the USB debugging is turned off now as the phone appearntly did factory reset so i cant acess XiaoMiTool V2 again and when i try to wipe data from TWRP it says unable to wipe data ... please help im stuck on TWRP loop now
**UPDATE** i tried fastboot ROM using MiFlash tool but i get error since i'm stuck on twrp fastboot menue but after few restart it finally open the normal fastboot menue with the logo of the sitting rabbit which indecade this is miui 12 tried again to fash though Mifash tool and it worked (flashing the same version miui_VAYUGlobal_V12.0.6.0.RJUMIXM_eccd7da42b_11.0.zip but this time the fastboot version not the recovery one took few minutes then got error not catch checkpoint flash is not done then it reboot into the phone menue where i can click wipe data i click that and the phone (thankfully) opened into MIUI 12 LOGO screen
... theres an easier way to actually downgrade your MIUI using a trick through your phone only without root or pc or anything by changing the ROM file name before you click reboot wish i used that since its safer and official
omg finally Magisk installed successfully now didnt need to decrypt anything
now my last question is do i need custom ROM after rooting the device ? or does magisk mean its a custom root ? sorry first time rooting and i dont know if i need to install any apps or apply any setting or should i click update my MIUI now ?
Try the newest Unofficial TWRP from nebrassy (found in his thread here on XDA)
That supports decription.
I recommend arrowOS as custom ROM.
It's one of the oldest and works pretty well.
IMHO Stock ROM from Xiaomi is untrustworthy. Who knows what spyware they included.
Same for me now I have a question first I need a guide link how to install arrowOS or any better ROM also if I do that do I need to flash Magisk again or the device will be keep the Root ?
@Haldi4803 can you post the link of the TWRP as well ? There's many threads by nebrassy and they all seem old mine is the latest official and it doesn't work on miui 13 , I also heard of crdroid and derpfest ROMs for Poco x3 pro but I think they overheat much ? I didn't test so I'm just asking also what's the way to install a new ROM it seem little bit complicated but the ArrowOs thread doesn't explain all the steps in detail because I think it's for pro users I read on Google that there's way more steps to install a ROM
TWRP:
[RECOVERY] [12] [OFFICIAL] TeamWin Recovery Project
Introduction: Team Win Recovery Project or TWRP for short, is a custom recovery built with ease of use and customization in mind. We started from the ground up by taking AOSP recovery and loading it with the standard recovery options, then added...
forum.xda-developers.com
Unofficial Builds from pling with Decryption working:
https://www.pling.com/p/1833617/ (just take the newer one)
Installation guide for Arrow OS:
Instructions
FIRST INSTALL?:
Remove any fingerprint, PIN, or password in MIUI
Unlock the bootloader
Transfer ROM to internal storage
Install any suitable recovery
Flash ROM zip file
Do a data wipe in recovery (format data)
Reboot to the system, wait and enjoy
There are decent picture guides here on xda on how to unlock bootloader.
After bootloader is unlocked you can simply install TWRP via fastboot flash recovery recovery.img.
Detailed instructions here: https://twrp.me/xiaomi/xiaomipocox3pro.html
After you have installed a ROM. and gapps you can simply reboot and use the rom.
Whenever you need root you can reboot into recovery and install magisk.
Hi. I have unlocked Realme 5 pro eu version without os. Had RMX1971EX_11_A.17. I've got OrangeFox R11.0 recovery through fastboot mode and platform tools (first bablus twrp + vbmeta, then somehow was able to go to orangefox + vbmeta, got errors when tried to go straight to orangefox). It is possible to install rom through recovery or with pc but I need help with next steps to get working ROM, idk which one should I install. Tried to install some of the custom and stock but nothing worked. Any help appraciated.
I tried almost everything and was stuck in recovery loop. Last try: converted ozip to zip as in this guide https://www.droidwin.com/extract-ozip-realme-stock-firmware/ Zip flashed through OrangeFox, and I needed to delete all folders inside /data except media folder and it worked. Maybe it will be helpful for someone.
(Did everything once again as it worked and I wanted to be sure that everything is clean and... I got errors once again (no os, loops) but after few shots got it and it's working now... lmao never again messing with this phone.)
Unsure if this is the place since its also related to TWRP 3.7, any help is appreicated
Got stuck in a weird situation and wondering if anyone has ideas.
Current State:
Slot_A on OOS 11, can boot TWRP via Fastboot
Slot_B on OOS 12, can only boot into Fastboot
Originally on OOS 11, booted TWRP and made backups of all partitions (data, boot, system image, vendor image, etc.). Forgot to move this to computer so this is all still stored on device.
Proceeded with OOS 12 upgrade (into Slot B). Patched magisk, rebooted, then flashed TWRP 3.7 (FBEv1), direct installed magisk, rebooted. - Everything was functional, but decided to go back to OOS 11.
Thinking I could just use the TWRP backup made on OOS 11, I did the following:
Booted into 3.7 TWRP
Restored the backup for boot, system image, and vendor image
Set active slot to Slot A and reboot
It doesn't allow me to boot into the OS (Presumably because the data was re-encrypted for OOS 12?)
Set active-slot=b and reboot, but it's locked to fastboot.
I've attempted a few things, but I can't boot back into OOS. I would prefer to retrieve my TWRP backups first before doing an MSM reset.
When on Slot_A (older), I can only boot into TWRP 3.6.2 and 3.7. I'm guessing 3.6.2 can't decrypt since it's only configured for A11 and under, but not sure why 3.7 can't decrypt my data.
- It doesn't even ask for pin when TWRP launches; maybe it's reading the System for Slot_A and thinks i'm still on A11?
- running `twrp decrypt {pin}` doesn't seem to work. Unsure if there's something done to my lockscreen pin to be used as the encryption key/password?
When on Slot_A, attempting to boot into either the system or TWRP hangs.
Things I've tried:
Flashing A11 boot.img and magisk-patched boot.img to Slot_A -> Hangs on 1+ Spinning dots
Flashing A12 boot.img and magisk-patched boot.img to Slot_B -> Hangs on 1+ logo (Does show up on ADB though)
Booting Slot_B into TWRP 3.6.2 (Official, and Nebrassy unofficial for A12) and TWRP 3.7 -> Gets stuck on "Fastboot Mode" screen (fastboot cli still responds) or Hangs on snapdragon logo
Edit: Ended up using MSM. Needed device for work
I have a similiar problem to flash twrp to my phone ,
each time i try i get a fastboot loop too and i have to reset/unbrick it with the msm tool back to android 11
i use the OnePlus_7_Pro_Global_OxygenOS_11.0.5.1 package to unbrick the phone , i dont know how long and often i tried now to get twrp to work so that i can flash a custom fw ... i want root and a android 13 based cfw but i dont get it to work :/
I got it working with crdroid. heres some stuff
guacamole - Google Drive
drive.google.com
be carefull
¯\_(ツ)_/¯
------------------------------------
I got stable and decrypted fs RW working on crdroid 9.1 firmware other than some weird bugs
i put it in the 2023-twrp
MissAnthropin said:
I have a similiar problem to flash twrp to my phone ,
each time i try i get a fastboot loop too and i have to reset/unbrick it with the msm tool back to android 11
i use the OnePlus_7_Pro_Global_OxygenOS_11.0.5.1 package to unbrick the phone , i dont know how long and often i tried now to get twrp to work so that i can flash a custom fw ... i want root and a android 13 based cfw but i dont get it to work :/
Click to expand...
Click to collapse
I have the exact same problem! Have you found a fix yet? This seems to happen when I try to install Android 13 based roms, and when I install a rom like Lineage OS, using their recovery, it works just fine.
No, and I don't know why, maybe i do something wrong or it is the Modell that make this trouble.
I thinking to sell my OP7PRO and buy another one ( and then I have the same problem with the new phone )
No no let the jokes aside, it must work, i mailed with OnePlus Support Germany but they only helped me to install A11 w/root and recovery, i thought ok now I can update to A13 so I loaded A13, unpacked the boot.img, Patched the boot.img
Installed A13 w/out errors, rebooted - Fastboot loop
RIP
Started ranting instead
TWRP for guacamole development seems to be fairly scarce, last working recovery I tried was when they started using fastboot boot to enter it. It was pretty hacky even then, currently it seems that nebrassy is the maintainer for twrp for guacamole.
Github: https://github.com/nebrassy Android 12 thread: https://forum.xda-developers.com/t/recovery-12-official-teamwin-recovery-project.4269551/ Nebrassys Telegram has helpful info as well: https://t.me/NSSFB
last update I found was 2022:10:2 - https://www.pling.com/s/Phones/p/1835156
after a few days of torture I read a thread on here saying if you flashed twrp via magisk like you would if it was a magisk moule it would work normally. It worked on my device so I assume that its universal. I have filled my computer with guacamole related files Im uploading here before im forced to reinstall my os:
guacamole - Google Drive
drive.google.com
Just a fyi from what I have gathered from my experience you can get a stable twrp recovery with persistant / read write access and disabled encryption and basically use it with little error up until you try flashing a newer custom rom. My guess is when flashing a cfw the bootloader gets rewritten causing our boot image to become corrupted. Flashing twrp over / booting to twrp via fastboot or trying to install it via another custom recovery causes boot / recovery failures... meaning you cant really use it for flashing custom roms. I cant find the post with the install instructions I seen that helped me so here is what I think it was,
Found it: https://forum.xda-developers.com/t/how-to-make-twrp-work-in-your-stock-a12.4522667/#post-87985325
~ I have bricked this device constantly while ****ing around so unless youre prepared to go to war with the ****er, Id quit messing with it.
MSM flashing with windows is the only way to recover from the void.
Click to expand...
Click to collapse
using Linux systems for EDL is a bit more difficult to figure out but can be done > EDL https://github.com/bkerler/edl/blob/master/edl | https://github.com/andersson/qdl
Click to expand...
Click to collapse
~If you do brick I created a fastboot flashable A13 Oxygen os recovery rom and uploaded it to my google drive found under recovery_brick_fastboot.zip ~
Click to expand...
Click to collapse
lastly be mindful of a/b partition configuration or youll find yourself lost or bricked
Installation:
1. Obviously unlock the bootloader - OEM Unlock
2. Flash custom recovery (lineage/crdroid/etc)
3. (Personally I root here and again on the active slot so) flash magisk.zip
4. Reboot into installed ROM and install magisk android app and complete setup, reboot system
5. (another thing I like to do before flashing twrp) setup magisk enable all the basic options like prophide, deny list then set root userspace option to global.
6. Flash TWRP .zip (https://dl.twrp.me/guacamolev2/twrp-installer-3.7.0_12-0-guacamolev2.zip) via magisk
Alright! After all that you should be able to reboot into recovery via adb reboot recovery / fastboot or power menu and you find a working twrp recovery installed.
If you need help or want to **** around with the device you can @ me anytime and ill do my best to halp
2600 IRC (cornelius.scuttled.net >Nick captain >channel #guac)
Telegram https://t.me/+pxvpKToFo6pkMGYx
Discord https://discord.gg/MhvWgEfY
Pics
RolandStoner said:
Pics
Click to expand...
Click to collapse
You Confussing me a lot with your Posts before ...
i´m unsure what you mean exactly,
my bootloader is unlocked, with magisk i got a working root but after that i fail
what you mean with flash twrp with magisk ?
after unlocking the bootloader and get root, i tryd to flash twrp like before on other devices but that seems not working because i get then the fastboot loop
on another thread i found here on xda too, the guy wrote dont forget to activate the fastboot loop fix in the advanced options
but i not tried it yet again , so what should i do now ?
for now , i´m back on android11 , with stock oxygen os firmware
i have to do now the things like i did before again , unpack boot.img from the firmware that is installed on the device
patch it with magisk, flash it with "fastboot flash boot boot-patched.img" or is this step senseless ?
i mean you only wrote unlock bootloader and flash a cfw , but i don´t have a chance to flash a custom fw without a custom recovery ??
my recovery on my op7pro have no options for "install zip" or something else
addendum:
like i said you confused me a lot
addendum two:
or i do what i said before .. i sell my op7pro and buy me a one where i havent so much trouble installing twrp and root
i never had a phone before that made so much trouble in installing simple twrp ...
but i don´t found a phone yet that is compatible with kali and the pentest tools or wardriving tools like the oneplus , so i have a problem ,... i think i should drink now my selfmade blackberry liquor ( or blackberry booze ? ) and let the smartphone be a smartphone for now and power off my brain for a while
Yes, you need to patch your boot image via magisk and flash it with fastboot.
After you let magisk do its first time setup and then once it reboots you go to Magisk > Modules and flash the twrp recovery .zip file you got from twrp. link:https://twrp.me/oneplus/oneplus7pro.html just like you would if it was a magisk module.
the password for twrp decryption is your pin. Here are simpler instructions
https://forum.xda-developers.com/t/how-to-make-twrp-work-in-your-stock-a12.4522667/#post-87985325
****... I forgot a step.
after flashing twrp as a module in magisk you dont reboot, you go back to the main screen hit the install button and choose direct install
Now I understand it more, i had before rooted the phone successful with magisk, but then I made a wrong decision and booted into Fastboot and flashed TWRP in Fastboot Mode as I did it before with all my Smarties i had before, coz those way with Fastboot worked before all the time so I never thought that this is the error in the procedure
I give the twrp flashing with magisk a try.
Thx for the help
MissAnthropin said:
Now I understand it more, i had before rooted the phone successful with magisk, but then I made a wrong decision and booted into Fastboot and flashed TWRP in Fastboot Mode as I did it before with all my Smarties i had before, coz those way with Fastboot worked before all the time so I never thought that this is the error in the procedure
I give the twrp flashing with magisk a try.
Thx for the help
Click to expand...
Click to collapse
Thank @yassine2217 because I would never have done so either.... Still many bugs but twrp is twrp