Screen just broken. I need to access photos, etc.. How can I do it? Also phone is not mine. How can I boot to recovery? And I can't shutdown the phone because I can't touch the screen.
If the screen works little in upper corner screen, try enable bluetooth and connect BT mouse... This helped me one day.... or maybe usb mouse?
If the whole screen is kaput, only way is to change LCD and screen.
Related
Hello,
My phone was waterdamged and stop working completly.
I opened the case and tried to dry it.
after 48 hours of trying various stuff, there is blank screen, but:
1. The phone is booting fine, charging led is working.
2. Using Wondershare-Mobilego, i can backup all the content.
3.The touch interface seems to be working fine, i can see the menus via mobilego duplicate screen (can open the sms box or whatsapp and etc.)
4.Incoming messages keep coming...
I`m so frustrated that i`m using the phone blindly or like remote desktop.
Is it software of hardware fault?
THANKS
Tamir245 said:
Hello,
My phone was waterdamged and stop working completly.
I opened the case and tried to dry it.
after 48 hours of trying various stuff, there is blank screen, but:
1. The phone is booting fine, charging led is working.
2. Using Wondershare-Mobilego, i can backup all the content.
3.The touch interface seems to be working fine, i can see the menus via mobilego duplicate screen (can open the sms box or whatsapp and etc.)
4.Incoming messages keep coming...
I`m so frustrated that i`m using the phone blindly or like remote desktop.
Is it software of hardware fault?
THANKS
Click to expand...
Click to collapse
After water damage you can only expect hardware damage. to verify - when turning on the device, do you see anything on the screen? you can also reboot to bootloader (via the key combination or via the command adb reboot bootloader (and to reboot back to android use fastboot reboot).
If the bootloader shows nothing, 100% hardware (although there is really no need to check, probably is). You can try changing screen, but the problem could also be in the socket (but I think if it were the socket the phone would not even boot). Worth a try.
Thanks, but no good...still blank screen - no display.
As i mentioned, the phone is functioning well (as seen at duplicate screen).
When you offering to change screen, you mean the lcd touch digitizer only?
I don`t need to buy the screen itself, right?
(I can`t parse outside links yet from ebay)
Tamir245 said:
Thanks, but no good...still blank screen - no display.
As i mentioned, the phone is functioning well (as seen at duplicate screen).
When you offering to change screen, you mean the lcd touch digitizer only?
I don`t need to buy the screen itself, right?
(I can`t parse outside links yet from ebay)
Click to expand...
Click to collapse
I mean the LCD itself. If touch is working, the problem is the LCD itself, not the digitizer.
You right, it seems that the touch working fine.
You think that a LCD display screen replacement would be the best try? can you paste a link from ebay please?
My screen is cracked since few mounths. After the drop the touch screen didn't work for half of the screen, the half, in orhizzontal, where the screen is cracked. Tonight I tried here (Sony eSupport - Electronics - Drivers & Software) panel calibration tool, now the touch screen works everywhere and now it's the situazion is worst then before. The cracked screen press itself and I can't use the tablet. Now I disabled touch screen in device manager, but my SP3 without touch is very sad I want to ask if there is the possibility to disable only part of the touch screen, the screen is cracked only for a few cm, I could use it completely even without that portion of the screen. Thanks.
I doubt you woudl be able to disable part of it, it would be a case of just disabling it full stop as it'll get worse..
Hi,
my name is Josemari, from Spain.
I have a TF101 with dock (and original rom from Asus) that does not display anything on screen since a soft fall from 10cm (daughter in a very very small chair).
When i plug the charger, it works (and beeps -charge-). When i plug the dock, also beeps. When i connect through hdmi output to my tv, it also works. I can use the tablet perfectly with my fingers.
What can i do?
I disassembled the tablet and i checked all conectors, but i do not see anything wrong.
Thanks.
I had the exact same problem. Even though it has fallen before without a problem, in my last 2 cases it was a loose connection for the video screen. I had to open up the tablet and simply push the video connection back on all the way. It's rather easy if you're familiar with taking things like this apart. Make sure you are careful when you re install the side trim that holds the buttons. It's easy to break the red tabs that press against the buttons. It may be helpful to you to look up a disassembly guide. I believe if you google the specific issue you will find pictures. Again it's been a long time. Hope this helps
I have the same issue since a few days.
Difference here, when I boot up (holding power button until reboot) the screen is on (Asus logo and boot animation)
The display goes balck / disappears (backlight off) when the lock screen comes up.
Checked the inner display cable and connector with no success.
Did a factory reset and it was working again, until I changed the brightness to a higher level. Then the screen was dark again.
I managed to change brightness to a lower level using the working HDMI interface. After that I switched the tablet off and on and the screen was lit up again.
Another effect: when power adapter is plugged in, I can go to a higher brightness level until the backlight turns itself off.
It looks like a hardware defekt of the backlight electronic to me. Couldn't find any spare parts, such as backlight inverter, though.
Can anybody confirm this or knows how to repair?
I will use it at 30-50% brightness now and see if it gets worse over time.
My screen is no longer working. Initially a sliver of the very top right corner worked, and I was able to cast to my tv and start backing up some things but casting stopped. Now even that corner is out. The touch part of the screen works, just not the display so I don't know what I am clicking.
Anyone have any ideas?
I tried a USB-C to HDMI adapter, but that did not work.
I apparently do not have USB Debugging flipped on
Hey, so my phone's screen recently broke, and it was still working perfectly in Samsung DeX mode. However, I made the mistake of disabling it because something I wanted to do required normal screen mirroring. Now, when I plug the phone through HDMI, I see a padlock on the screen, which normally requires me to enter my pattern to unlock the phone and have the screen mirror normally (but the screen and seemingly touch aswell are broken).
- Samsung S20 FE
- USB Debugging is disabled, so i cant use scrcpy
- I am able to feel vibrations when using a mouse, so maybe there would be a way to enter it blindly, but the pattern is too complex for me to do that
- I don't think I have a normal PIN but I don't recall, some people said pressing space twice on a keyboard then entering it could help, no luck
- I'm was able to see the device once in sideload mode, probably through recovery mode? (screenshot below)
- I currently see the device as unauthorized (2nd screenshot)
I'm pretty much open to any way of doing this, even disabling the pin would be okay.
Thanks in advance!
Managed to fix this using a windows drawing pen, finding where the dots for the patterns are located with vibration, and mapping them on a piece of paper.
another way would be connect TV or monitor with HDMI adapter and connect usb mouse / keyboard
aIecxs said:
another way would be connect TV or monitor with HDMI adapter and connect usb mouse / keyboard
Click to expand...
Click to collapse
The thing is, the pattern doesn't show on the external display.
All you see is a grey screen with a padlock and the time.
If you have a PIN though, that does work cause you just have to hit space twice, type it in then hit enter. Easy even if you can't see.