I recently bought a Poco X3 NFC and after installing a Glass screen protector I found out that the Touch does not work properly on the top of the screen and this only happens when I lay down the phone on a soft ground like bed (vertically holding in the hand causes no issue!).
I even changed the Glass but the problem persists. Without a Glass there is no issue and Touch functions just smoothly.
I would like to know if anyone has experienced the same issue or this is just an issue with my phone.
Your replies are highly appreciated.
Related
Hello guys,
I've been using DHD for quite a long time and I never experienced any problems with this phone until I noticed the digitizer is cracked. I just took the phone out of my pocket and realised that it doesn't react when I touch the screen - there is a small crack in the corner. I think this is just the digitizer because the image is displayed correctly and there are also no scratches on Gorilla Glass (i also used screen protector). I have not dropped the phone recently (neither hit it with a hammer) and I'm wondering if it is possible that the digitizer has a factory defect and what about the warranty in such a case because when I heard what is the cost of repair...
Any clues guys? This is very important...
I had a similar problem with my screen.
The upper part of my screen was devastated with pieces of glass coming out regularly.Yet,the touchscreen worked.
Your case is pretty weird.I think you should take it to HTC and try to persuade them that its a defect if you're sure you haven't damaged it!
GoodLuck :good:
(There's plenty of guides to help you replace your screens out there...so I would redo one of those.)
Ive replaced a few of these S3 screens with new glass and the double sided tape method and the only issue that always happens is that the glass will touch the digitizer in the middle once in awhile. This registers a touch that is stuck on and locks up the rest of the touch screen. The only work around is pressing on the glass around the outside of the lcd to release the unwanted touch. Tonight I discovered a great method for curing that problem. I removed the glass and cleaned up very well. Then applied a cut down screen protector for a LG spectrum to underside of the glass to bridge the gap between the glass and the digitzer. (The spectrum protectors was big enough to trim down to the right size) Retaped and assembled. This has worked perfect to correct and the screen looks great! Make sure to buy a screen protector that is clear. A protector that is anti-glare would dim the display. With the clear you cant tell its there. The touch screen acts like new. Very happy with the results!!
Dan
Hogan1975 said:
(There's plenty of guides to help you replace your screens out there...so I would redo one of those.)
Ive replaced a few of these S3 screens with new glass and the double sided tape method and the only issue that always happens is that the glass will touch the digitizer in the middle once in awhile. This registers a touch that is stuck on and locks up the rest of the touch screen. The only work around is pressing on the glass around the outside of the lcd to release the unwanted touch. Tonight I discovered a great method for curing that problem. I removed the glass and cleaned up very well. Then applied a cut down screen protector for a LG spectrum to underside of the glass to bridge the gap between the glass and the digitzer. (The spectrum protectors was big enough to trim down to the right size) Retaped and assembled. This has worked perfect to correct and the screen looks great! Make sure to buy a screen protector that is clear. A protector that is anti-glare would dim the display. With the clear you cant tell its there. The touch screen acts like new. Very happy with the results!!
Dan
Click to expand...
Click to collapse
interesting. i have recently replaced my S3 with the prokit from amazon, but had occasional touch issues like you described. i might try this. to be clear, with the screen protector, do you still need to apply any adhesive between screen and digitizer?
cowboybebop98 said:
interesting. i have recently replaced my S3 with the prokit from amazon, but had occasional touch issues like you described. i might try this. to be clear, with the screen protector, do you still need to apply any adhesive between screen and digitizer?
Click to expand...
Click to collapse
No you do not need adhesive/loca between ur screen and digitizer. BTW I've went down that road with using the adhesive...not very fun. The UV glue method is tough to apply correctly. That is why I was experimenting with the under glass screen protector method.
One more add on to my description of adding the screen protector between glass and digitizer is doubling up on the double sided tape around the perimeter. I wanted to make sure I got the tape high enough to bridge the slightly larger gap between the glass/digitizer due to the screen protector. Hope this helps.
maybe not the perfect solution....
The wifes phone that I tried this fix on is working awesome. She said it hasnt had one issue since. But I've tried this method on two other S3 without the same sucess. Both were the US Cellular verisons of the phone (wifes is Verizon), and both still had touch screen lockups. So had to redo with the LOCA replacement method to cure issues. Just FYI...
so i finally bought a screen protector. i dont get it. bought a zagg which has always been good. my tablet is unusable with that screen protector on. nothing but ghost touches and i cant even use it so many touches and things opening up. i remove it its fine again. anyone have this experience?
Hi all
My moto Maxx has gone through a lot, but the strangest problem yet started yesterday.
As you can see on the attached video, half of the screen is constantly scrolling. This happens in fastboot and recovery mode as well, so I'm pretty sure it's a hardware problem.
The digitizer still works perfectly, and registers touch where the icon or button should be positioned on the screen. The moving screen also does show everything correctly, just in this crazy scrolling way.
I'm not very hopeful in fixing it, but was wondering if anyone has ever seen this, and if you guys think this is a broken display(and any way to test this?) or a broken GPU. If it is in fact the display, I might consider replacing it.
Some background on all the terrible things I did to this phone:
- Dropped it and cracked screen in September.
- Replaced the glass myself, slightly burned display when removing glass without any consequences (just a tiny mark on the top right, the side that actually still works).
- Dropped again, broke glass again, never bothered to fix it, some small pieces are missing so dust, sweat,.. could've gotten int.
Video:
Most likely the display being broken.
Even when my tempered glass protector is missing chunks the screen starts to funk up. Only worse being the real screen especially the digitizer.
You might be right pjd, or at least screen related.
I opened it up yesterday evening, and I think it might be the cable connecting the screen. Depending on how I positioned the screen and thus the angle at which the cable was bent, it was fixed, the same, or just completely black.
The only thing I have to try to find out now is if it's the kabel, or the connector on the motherboard. Any suggestions on how I could test that are welcome!
hi guys ive noticed that when typing on the display without much pressure i get a rainbow affect only for the time im applying pressure just wondering does anyone else have this problem or am i developing a hardware problem
its a bit like applying pressure on my laptop display with not much force
Are you using a screen protector? If you are, is it possible the protector is not sitting right against the screen?
I have had two idol 3 phones and I didn't notice any rainbow affect on either phone.
audit13 said:
Are you using a screen protector? If you are, is it possible the protector is not sitting right against the screen?
I have had two idol 3 phones and I didn't notice any rainbow affect on either phone.
Click to expand...
Click to collapse
ya i had a glass one installed removed it and still the same so thinking it maybe faulty
I used both phones with a glass protector and not problems with or without the protector.
Sounds like the top glass is not fully bonded to the lcd.
audit13 said:
I used both phones with a glass protector and not problems with or without the protector.
Sounds like the top glass is not fully bonded to the lcd.
Click to expand...
Click to collapse
didnt notice it when i got it new so think its a newish fault lol do you think its worth trying to get a repair or will it not really cause any future problems
I would get it checked out asap. Who knows, it may be a sign of future problems.
Looks like screen problem