Hello I try to install with odin a new android version on my note 5 and it gave me fail . Now I have a blue screen on it saying to resolv the problem with Smart Switch , but when I connect the phone ,Smart Switch does not reconize my phone . I don't know what to do ,you might help me with some ideas .10x in advance.
PaulHoras said:
Hello I try to install with odin a new android version on my note 5 and it gave me fail . Now I have a blue screen on it saying to resolv the problem with Smart Switch , but when I connect the phone ,Smart Switch does not reconize my phone . I don't know what to do ,you might help me with some ideas .10x in advance.
Click to expand...
Click to collapse
Thread closed.
Duplicate:
http://forum.xda-developers.com/general/xda-assist/odin-flash-failure-t3429537
Do not create a thread or post more than once.
Hello Friends ,
While flashing CM13 and making some changes in sdcard0 to ext4 format , my phone suddenly went to hard brick or as it seems with following condition : No logo, no vibration , No LED except for one blink whenever it is connected to usb wall charge or laptop .
Cant detect via flashtool on system , only part is while connecting with Windows8 , it makes the usual windows ping as if you connect a flashdrive or any other hardrive .
I was using xperia TX CM12.1 unofficial version .
Attached 2 snapshots showing the errors , before it went to sleep .
Once the phone went blank and i connected with my laptop , it pops up with QHSUSB_Dload driver installing message .
Please help , as I couldnt find any proper resolution to this solution .
@Antiga Prime & @Adrian DC any view .
srd34 said:
Hello Friends ,
While flashing CM13 and making some changes in sdcard0 to ext4 format , my phone suddenly went to hard brick or as it seems with following condition : No logo, no vibration , No LED except for one blink whenever it is connected to usb wall charge or laptop .
Cant detect via flashtool on system , only part is while connecting with Windows8 , it makes the usual windows ping as if you connect a flashdrive or any other hardrive .
I was using xperia TX CM12.1 unofficial version .
Attached 2 snapshots showing the errors , before it went to sleep .
Once the phone went blank and i connected with my laptop , it pops up with QHSUSB_Dload driver installing message .
Please help , as I couldnt find any proper resolution to this solution .
@Antiga Prime & @Adrian DC any view .
Click to expand...
Click to collapse
Regardless of what you may or may not have done for that to happen, I would try following this guide.
You need to register an account in order to download the files, btw.
@Antiga Prime
Reached to a level where S1 tool works but shows Unknown SIN version . snapshot attached and again stuck ,
thanks added for your quick response and related link .
what else can be done
Antiga Prime said:
Regardless of what you may or may not have done for that to happen, I would try following this guide.
You need to register an account in order to download the files, btw.
Click to expand...
Click to collapse
srd34 said:
@Antiga Prime
tried using the steps shown except for opening the phone part for test point and got error attached .
Thanks for the link though . any other view ?
Click to expand...
Click to collapse
You're welcome. Any other view? No, but the entire point of that tutorial is that you have to use the testpoint, that's why you're getting that error. If you don't feel confident enough to do it yourself, I guess you'll have to take it to a repair shop.
@Antiga Prime There is an update now . need correct SIN file for xperia TX refer snapshot ..
Antiga Prime said:
You're welcome. Any other view? No, but the entire point of that tutorial is that you have to use the testpoint, that's why you're getting that error. If you don't feel confident enough to do it yourself, I guess you'll have to take it to a repair shop.
Click to expand...
Click to collapse
srd34 said:
@Antiga Prime There is an update now . need correct SIN file for xperia TX refer snapshot ..
Click to expand...
Click to collapse
I have never done this procedure, by the way, but what I can gather from your screenshot is that either the person who wrote the tutorial I linked to originally made a mistake and uploaded the wrong file, or you're using the wrong file. It seems that at some point you might have also downloaded the file found here, which is a forum post for Xperia SP. I do not know which one is the correct file, but just make sure you're using the correct one. If the one posted in the tutorial I linked to doesn't work, I guess you'd have to find one that does.
Thanks , but it seems this SIN file is also not compatible .
Seems the last resort is to reach service center .
Antiga Prime said:
I have never done this procedure, by the way, but what I can gather from your screenshot is that either the person who wrote the tutorial I linked to originally made a mistake and uploaded the wrong file, or you're using the wrong file. It seems that at some point you might have also downloaded the file found here, which is a forum post for Xperia SP. I do not know which one is the correct file, but just make sure you're using the correct one. If the one posted in the tutorial I linked to doesn't work, I guess you'd have to find one that does.
Click to expand...
Click to collapse
srd34 said:
Hello Friends ,
While flashing CM13 and making some changes in sdcard0 to ext4 format , my phone suddenly went to hard brick or as it seems with following condition : No logo, no vibration , No LED except for one blink whenever it is connected to usb wall charge or laptop .
Cant detect via flashtool on system , only part is while connecting with Windows8 , it makes the usual windows ping as if you connect a flashdrive or any other hardrive .
I was using xperia TX CM12.1 unofficial version .
Attached 2 snapshots showing the errors , before it went to sleep .
Once the phone went blank and i connected with my laptop , it pops up with QHSUSB_Dload driver installing message .
Please help , as I couldnt find any proper resolution to this solution .
@Antiga Prime & @Adrian DC any view .
Click to expand...
Click to collapse
Hello. Have you find the decision about QH SUSB on TX?
No solution yet . The device still with me and gets blinked when connected with charger , however . No solution to recover from hard brick I believe . Service centre also of no help since this model was a limited edition one and they dont have in their SKU list to do anything . keeping as fancy paper weight
dear all
i have installed firmware nxt-l29c185b580 , i decided to hard reset my phone and after hard reset finish i was asked for FPR , i actually know the email and password but i have no way to input them due to no keyboard only google voice
i spent nights trying to input but i could not by pass that through google voice only.
is there any way to install the keyboard from fastboot with computer connect and why did it disappear after hard reset ?
is there any way to remove this connected email from my device remotely from my computer or any web page ( i have access to this email from my chrome "
fast boot show " relocked bootloader " and " FRP locked
what can i do to get my phone back please help , what is the possible solution now
thank you guys , my issue has been resolved by roll back update and full firmware of marshlome and my keyboard came back and i resolved my issue
thank you
Hii, I am facing a problem in my huawei mate 8. After a hard reset the keypad disappeared from the mobile & I am not able to setup the mobile. Could anyone help with any suggestions......
My mobile is totally noy operational,while doing the factory reset,keypad not appearing for the password input.How to get the keypad back.....?
a year ago I had the same problem and I think it was solved by installing the rom again or using another rom.
No need to reflash or go back
Guys is simple .You cannot insert the credentials to your router and so on because the keyboard is missing ?First grab another phone and start a hotspot without any password.connect with mate on that hotspot,then spell pressing the circle clear and loud Fdroid.Install ,then on the search in fdroid say liud and clear keyboard .install the first keybord aviable on fdroid .have fun and remamber ,no need to flash enyhing .think twice!
Hello everyone , i'm Malick from Ivory Coast west Africa.
I purchased an S10e (SM-G970N) second handed to an unknow person on an ad website and i'm not able to use the device ! impossible to acces camera , to use sd card , to make a screenshot , even impossible to enable bluetooth.
There is a notification which i'm not able to get rid of it , even factory reseting it don't help. I'm starting to think that it is a stolen device ....
The notification is saying "Device Locked" and there's some korean writing after that , when i maintain the notification , it's saying that i cannot hide this notification , and the adress given is : com.sds.emm.emmagent.lite.samsung" , when i just click on this notificatin , it's starting to download something and suddenly stop downloading it and it state "Application not installed" , i tried to translate the korean statement into english (check the screenshot)
I was on Android 9.0 and i've downloaded the recent version Android 10 with OneUI 2.0 which i've installed via Odin , but same thing , i can't do anything , the seller blocked me on whatsapp and he's not even picking up when we call , even with another number.... so i just forgot about tracking him and make him refund me...
i just need some help to try to unlock the device , or if you guys can't help , at least tell me what is this kind of lock that i've never seen...
maybe it has something to do with mdm (Mobile device management)
Thing i actually tried :
-flashing via Odin latest firmware after wiping the old rom (FAIL)
- tried flashing via Odin global firmware , passing from SM-G970N to SM-G970F (FAIL)
-installing twrp recovery after unlocking the bootloader (SUCCESS)
-installing HadesOS via twrp recovery , installed succefully , but the error still persist so (FAIL)
-Tried to install LineageOS , not even willing to pass the bootscreen , stuck in a bootloop (FAIL)
Don't know what else i can try , if someone has more experience than , and/or we can flash something via Odin , you can tell me i'll give it a try... i have nothing to loose , except a very good looking phone....
Thanks in advance for any help
(PS : SORRY FOR THE ENGLISH MISTAKES ! I'm just a french guy )
Is it still relevant?
Exilion90 said:
Is it still relevant?
Click to expand...
Click to collapse
Hello , no , the problem has been solved awhile ago (about 2 months) , i solved this wirelessly , i paid 25$ paypal to a guy who resolved it in a blink of eye. now my phone is still working without any problems
hello everyone . sorry for my mistake because new here at this platform .
As watch started and it was in Chinese language so i do not which button i pressed and after restart its give black screen and show an error can not connect to your phone contact customer care center . As i tired to use wireless mode but AP mode is not working and then i tried to use cable to flash it after flash its start reset but same problem can not connect to phone . i downloaded many firmware but problem remain same . Just roll back firmware work and watch start but its in standalone status and cannot connect to WiFi or Bluetooth and its shows watch can not connect to phone you need to connect to previous phone and login to Samsung account . but as this watch have no lock and is removed from Samsung account . now please help me what to do . i am attaching one link where i uploaded pictures regarding my problem as i ma new user can post link please help me. Thank you
h.t.t.ps://w.w.w.flickr.com/cameraroll/
Click to expand...
Click to collapse