Hi i've two problem with CanBus on Vw Golf 6.
1. If i open APP for steering weel config i can't see any button and i can't configure anything
2. Doors open/close don't work. I can see Temperature, Oil, RPM but doors doesn't work at all
I've this problem with my actual PX5 KGL and with my old RK3188 unit
Details of my actual unit:
Type KGL
MCU 2.47
ROM Malaysk PX5 2.0
capu81 said:
Hi i've two problem with CanBus on Vw Golf 6.
1. If i open APP for steering weel config i can't see any button and i can't configure anything
2. Doors open/close don't work. I can see Temperature, Oil, RPM but doors doesn't work at all
I've this problem with my actual PX5 KGL and with my old RK3188 unit
Details of my actual unit:
Type KGL
MCU 2.47
ROM Malaysk PX5 2.0
Click to expand...
Click to collapse
1) car specific headunits which Steering wheel buttons control are based on Canbus Box CAN NOT BE MAPPED by the Steering Wheel APP. They are hardcoded to specific Headunit functions. There is a tool MTCDTools from @f1x that could help you to assign new functionalities to your SWC buttons.
2) I don't know why do you report it as a problem. It was promised to you that Doors Opening/Closing shall be working with the canbus box supplied? Each Can-Bus Box is capable to decode specific features of the car. If that functionality was not present on PX3 or PX5 is due to your can-bus CAN'T DECODE (or has not been programmed to decode) the open/close door system.
The CarSettings app just receive which functions are being decoded by your can-bus and show the decoded information received.
Can you point me to the location of the CarSettings app? I can't find it in my newly installed headunit. I couldn't find any in the Google play store.
I found a fix for you problem, capu81, you need to go to factory settings, Canbus and try to change the can bus setting with some other value. The can bus box has the ability to decode some dozen car types, and it's probably not set for your car properly. When this setting is done right the apps that everyone is looking for, the Car info and Car settings are going to be available and should contain all the old settings that were available on your factory head unit. The default password for accessing factory settings is usually 126.
And if the canbus decoder is not supporting your vw golf 6, then go to roadnavi and buy their CAN-bus Decoder and select the right model. Eg: RN Model: C257 Golf 7
Thank you to all for the answer.
The doors signal is not a big problem, l leave it in this way.
Steering Well remapping: with MTCD Tools i can create custom action. For example: i've button for MUTE. If i remap button with MTCD Tools and assign Vocal Google Search to it the action is fine but MTCD became MUTE. There is a way to disable factory action and use only MTCD Action?
I have this problem too (no mapping option) but my steering wheel works on my Ford Focus. Check your CAN Bus box and make sure the model of it matches what's selected in Factory Settings. My CAN Bus box is a Raise 06, likewise it is selected in Factory Settings to match it.
@capu81 I am having this same issue with my doors on my Erisin ES6405V. Currently emailing with Erisin back and forth trying to get this fixed. If there is ever an outcome, I will let you know.
capu81 said:
Thank you to all for the answer.
The doors signal is not a big problem, l leave it in this way.
Steering Well remapping: with MTCD Tools i can create custom action. For example: i've button for MUTE. If i remap button with MTCD Tools and assign Vocal Google Search to it the action is fine but MTCD became MUTE. There is a way to disable factory action and use only MTCD Action?
Click to expand...
Click to collapse
I have same exact issue. Did you find a solution to it?
Hello, I have the exact same problem only the other way around, my steering wheel buttons are mapped and working, car is showing open/closed doors but for oil, rpm, speed battery nothing. I tryed messing with the canbus setup and change to other setting from VWto maybe get it to work but no luck. Any ideas on how I can solve this? I have a MTCD unit px3 2GB 7.1.2
I have also problem with CANBus decoder. The only problem is that when i drive and change shift activate rearview camera, all the other stuff (swc, door signals and also reverse enable the rear view camera) works fine. There is something like update or a settings that works fine. I have a FIAT Bravo model >2007 and in factory settings seems to be all ok
dirty_dty said:
Hello, I have the exact same problem only the other way around, my steering wheel buttons are mapped and working, car is showing open/closed doors but for oil, rpm, speed battery nothing. I tryed messing with the canbus setup and change to other setting from VWto maybe get it to work but no luck. Any ideas on how I can solve this? I have a MTCD unit px3 2GB 7.1.2
Click to expand...
Click to collapse
j0nnymoe said:
@capu81 I am having this same issue with my doors on my Erisin ES6405V. Currently emailing with Erisin back and forth trying to get this fixed. If there is ever an outcome, I will let you know.
Click to expand...
Click to collapse
These are not "problems" - CAN Bus support depends on your car model, the manufacturer of the CAN Bus box and whether MTC/HCT have written the software for these things. If youve played araound with all the CAN Bus settings and not every function works then there is nothing you can do . . . apart from get hold of the CAN Bus protocol for your vehicle,, the MTCD MCU protocl and then write and app for it. There are 1000s and 1000s of cars on the market (and 1000s no longer made) it would be far too costly to make full CAN Bus support for EVERY car on sale, so only the most popular cars are supported and even then not all models and/or all functionality.
@j0nnymoe - dont waste your time contacting Erisin, they are a seller not a manufacturer and theres nothing they will be able to do.
@typos1 do you think maybe it can be fixed if I update the MCU to the latest version? It just seam strage for it to work in open/closed doors but not for the rest, I'm thinking maybe a mismatch of canbus and software and maybe that is why it dose not work. (Just a wild guess)
dirty_dty said:
@typos1 do you think maybe it can be fixed if I update the MCU to the latest version? It just seam strage for it to work in open/closed doors but not for the rest, I'm thinking maybe a mismatch of canbus and software and maybe that is why it dose not work. (Just a wild guess)
Click to expand...
Click to collapse
Updating the MCU may certainly help.
@typos1 that is good to know, I can keep my hopes high for a bit longer but I am sceptic about the MCU update [email protected] gave me.. He did not test it and there is nobody else I could find that updated to the latest version of XRC to confirm it is the right one.
dirty_dty said:
@typos1 that is good to know, I can keep my hopes high for a bit longer but I am sceptic about the MCU update [email protected] gave me.. He did not test it and there is nobody else I could find that updated to the latest version of XRC to confirm it is the right one.
Click to expand...
Click to collapse
What do you mean "the right one" ?
If you remember on the other thread, he just attached a dmcu file of the latest MCU for my XRC unit and said he did not tested it.
dirty_dty said:
If you remember on the other thread, he just attached a dmcu file of the latest MCU for my XRC unit and said he did not tested it.
Click to expand...
Click to collapse
I cant see any reason to doubt him.
@j0nnymoe - dont waste your time contacting Erisin, they are a seller not a manufacturer and theres nothing they will be able to do.
Yea I gave up on that a while ago. I've had a couple of these units before from other sellers (xtrons/eonon) and the canbus on those units worked fine. I suspect the KGL unit's doesn't like my car for some reason. I toyed with the idea of getting another canbus decoder..maybe if I can get one cheap enough I might try it.
j0nnymoe said:
@j0nnymoe - dont waste your time contacting Erisin, they are a seller not a manufacturer and theres nothing they will be able to do.
Yea I gave up on that a while ago. I've had a couple of these units before from other sellers (xtrons/eonon) and the canbus on those units worked fine. I suspect the KGL unit's doesn't like my car for some reason. I toyed with the idea of getting another canbus decoder..maybe if I can get one cheap enough I might try it.
Click to expand...
Click to collapse
Did you try another canbus decoder?
I've got an a3 and I'm using a kgl unit and nothing shows on my dis screen on the dash but when I've had a unit from xtrons before that did work.. I'm guessing kgl must use cheaper canbus decoders and I've been thinking like you and we're thinking of buying another decoder from xtrons to try
I can`t find a working SDVC app for my PX5 GS unit. It is my second unit because the first has had a fault and was exchanged. On the first unit I used Graser´s Dasaita tool for volume control. On the new unit that isn´t working anymore and also MyMTCService does not recognise the unit as MTCD and so the sound control is not working.
The only thing that is different to the old unit are the connectors. The GPS connector uses now a Fakra plug, but I don´t think that this is a problem since all other GPS apps are working normally.
Neither Malaysk, the original GS ROM nor a HA ROM is working. I've tried also different MCU's.
Here you can see the problem with Grasers Dasaita tool. I am not driving and not changing the volume level: https://youtu.be/aT0asijim5g @Graser maybe you can help me?
Hi there,
I buyed a xtrons px5 head unit for Opel, I installed malaysk firmware 2.0 for further customizations. Unit is running almost fine. Had some overheating issues after long driving with navigation. Dont want to open and add heatsink because losing warranty.
One big annoying problem is USB Permissions Message when using USB CAN Adapter with Torque. Every boot or wake-up from standby unit asking me again for USB persmission for canbus adapter, even if I tap use by default.
Does anyone know how to fix that?
Xtrons now selling units with Android 8.1, what the ****? New hardware? No update for existing px5 units?
My dashcam from xtrons (UCam china chipset) displays wrong speed and perhaps wrong position. My friend with stock firmware has same problem, any fix for that?
Greetings from Germany
Hi MTCD community.
Thanks to the time between the years (that's how we call December 27th to 31st in Germany), I had time to upgrade my HU. Up to now I had a RK3188 quad-A9 one (Erisin ES2508B, KGL) that had a proprietary power connector and a external canbus decoder box. (more information here: http://vi.vipr.ebaydesc.com/ws/eBay...descgauge=1&cspheader=1&oneClk=1&secureDesc=0 )
That external canbus decoder of the unit has a few dedicated output pins for illumination, reverse gear and a UART (?) style digital RX/TX connection to send wheel-button key commands. It's a perfect example for a Chinese product. This solution it easy and works - almost:
On Mercedes cars the wheel-buttons are used to steer the so called Kombi (KI). KI and HU are connected via canbus. Key commands are send in one specific can-message. The canbus decoder box is said being made specifically for Mercedes cars. While it correctly decodes button presses it fails to decode the current KI menu. As a result the HU will always interpret the "prev./next" buttons, even when you're not in the KI's Audio menu. As a result you either stop using your KI (bad option) or you disable some keys in the HU (that's what I did). The decoder box is also only reading the canbus and thus not able to send audio titles or the current radio frequency/station name to the KI.
Because of the decoder box sitting between HU and KI I never tried to enhance functionality because that would have ment either connecting another R/W canbus dongle to the HU or replacing the chinese decoder box and reverse engineering the RX/TX communication between decoder box and HU.
---
The newer PX5 unit that I now own (Erisin ES7689C, KGL?/LM?, http://www.ebay.co.uk/itm/Android-8...s-W203-W209-/123151147422?hash=item1cac61619e ) has a Quadlock connector (that's the correct name for the multi pin connector that became popular on HUs beginning in the early 2000th) and no external canbus decoder box (it is indeed perfectly plug'n'play). It is also able to identify itself to the KI as Radio which means it is also writing to the canbus. Compared to an original OEM HU, information is still extremely limited and it again fails to interpret only wheel-button commands send from the KI's Audio menu. - But, it is able to write to the canbus, so potentially this is a much better starting point for enhancements.
Now the key question: Does anyone know how the HU is communicating with the canbus? Is the decoder box just inside the HU's housing (and again being an extra translation module) or is it a proper canbus device controlled by an app or service from inside the HUs android?
Good piece of info mate. Thanks a lot
Unfortunately i am not able to answer the question due to limited knowledge.
I own a Mercedes w164 and have the same issues and i am keen to find a solution. Open a thread for that too here > https://forum.xda-developers.com/an...t/adapter-help-mercedes-t3903165#post79005544
My MTCD idetails are :
Unit: MTCD PX5
MCU: MTCE_GS_V3.00_3
ROM: Halk9 Mod 3.1 (Android 8)
Can Adapter : GS 10280514 / HW:V2 SW:V3
Can adapter Setting: 23 Benz_B200(simple)
On another thread more HW related you can find pleanty of info >
https://forum.xda-developers.com/an...elopment/mercedes-benz-class-comfort-t3680320
Also this guy did some work on canbus : http://honeysw.com/canproject.php
and here another piece of info : https://forum.xda-developers.com/an...-units-qa/how-bus-messages-make-unit-t3352343
Hi I also have a MB lol, a w203.
I have been through several head units of types makes etc, so know exactly what you mean. Although I never heard of 'ki' before.
My latest unit I have is def very good (best was a pioneer with separate car-pi can decoder) and that is also an erisin.
Great minds an all that eh!
The unit I have is a 4/32gb android 8. MTCE. It was working very well until I developed a problem with my reverse camera signal not getting picked up. Was switching OK but no image??
Anyway I bit the bullet and installed the custom rom by Malaysk which helps the camera but no steering control (for me) on 3rd party apps.
There is some talk about mtce files etc but I couldnt get anything to work until I installed a brilliant prog called mtcdtools (free from github).
Very techy to understand / use but with the info and help from others managed to replicate enough to get the two up/down left buttons working perfectly on all apps. It starts up by itself and stays in background. I'm very pleased with result and sure it could do much more if i only knew how. Def give it a go.
Also the up/downs only while in the audio sub menu and they operate whichever music app is running even while in the background if that makes sense. The right volume buttons always worked anyway, and with the phone.
I think the real challenge now will be getting info in the dash display to correspond with what ever app is on top. Currently mine just says audio off when using dab, but displays station number in radio and time elapsed from music player., but nothing from nav.
Hi All,
I need to find some info for the Can adapter so i can fix my issue and help other people with similar problems too .Owner of an MTCD PX5 unit, specific for Mercedes ML (W164) that came with the Can adapter.
From day one the steer wheel buttons worked (vol up/down, phone) and reverse camera out of the box BUT i had no vehicle info at all (door opened, fuel level, temperature, parking sensors etc) as many of the users especially on VW units have. The car is a 2010 model therefore the canbus info should be plenty. Tried all the combinations of CanBus under the extra settings with no luck.
One think i noticed is that i had NO Vehicle.apk or microntek apk and MTCCanbus.apk installed on the unit. I tried to install but installation was failing for both. Even copying to system/app/** didn't worked.
Any idea ?
BTW Anyone knows what is the Knob Mode under extra settings ? Mine is set to : 2 10k/20K ADC Ports
Details:
Unit: MTCD PX5
MCU: MTCE_GS_V3.00_3
ROM: Halk9 Mod 3.1 (Android 8)
Can Adapter : GS 10280514 / HW:V2 SW:V3
Can adapter Setting: 23 Benz_B200(simple)
Hi, i have the same car the same headunit and the same problem.
All is fine but i want to have more can-informations/functions.
zollaki said:
Hi, i have the same car the same headunit and the same problem.
All is fine but i want to have more can-informations/functions.
Click to expand...
Click to collapse
Good to know that this is a generic issue and not specific to my unit and car. It seems a lot of people with Mercedes cars have similar problems. I wonder if this is related with the cheap implementation of the Chinese Can adapters or related with the car.
Will keep searching
Another thread is open with more technical details for similar issue, more HW oriented though here > https://forum.xda-developers.com/android-auto/mtcd-discussion-questions-development
I have the same car w164 and px5 android 8
The same problem.
No I have more problems the canbas stop working no reverse camera no Wheel key vol working and no led light on unit key, I think my canbus dead ?