Hi i've two problem with CanBus on Vw Golf 6.
1. If i open APP for steering weel config i can't see any button and i can't configure anything
2. Doors open/close don't work. I can see Temperature, Oil, RPM but doors doesn't work at all
I've this problem with my actual PX5 KGL and with my old RK3188 unit
Details of my actual unit:
Type KGL
MCU 2.47
ROM Malaysk PX5 2.0
capu81 said:
Hi i've two problem with CanBus on Vw Golf 6.
1. If i open APP for steering weel config i can't see any button and i can't configure anything
2. Doors open/close don't work. I can see Temperature, Oil, RPM but doors doesn't work at all
I've this problem with my actual PX5 KGL and with my old RK3188 unit
Details of my actual unit:
Type KGL
MCU 2.47
ROM Malaysk PX5 2.0
Click to expand...
Click to collapse
1) car specific headunits which Steering wheel buttons control are based on Canbus Box CAN NOT BE MAPPED by the Steering Wheel APP. They are hardcoded to specific Headunit functions. There is a tool MTCDTools from @f1x that could help you to assign new functionalities to your SWC buttons.
2) I don't know why do you report it as a problem. It was promised to you that Doors Opening/Closing shall be working with the canbus box supplied? Each Can-Bus Box is capable to decode specific features of the car. If that functionality was not present on PX3 or PX5 is due to your can-bus CAN'T DECODE (or has not been programmed to decode) the open/close door system.
The CarSettings app just receive which functions are being decoded by your can-bus and show the decoded information received.
Can you point me to the location of the CarSettings app? I can't find it in my newly installed headunit. I couldn't find any in the Google play store.
I found a fix for you problem, capu81, you need to go to factory settings, Canbus and try to change the can bus setting with some other value. The can bus box has the ability to decode some dozen car types, and it's probably not set for your car properly. When this setting is done right the apps that everyone is looking for, the Car info and Car settings are going to be available and should contain all the old settings that were available on your factory head unit. The default password for accessing factory settings is usually 126.
And if the canbus decoder is not supporting your vw golf 6, then go to roadnavi and buy their CAN-bus Decoder and select the right model. Eg: RN Model: C257 Golf 7
Thank you to all for the answer.
The doors signal is not a big problem, l leave it in this way.
Steering Well remapping: with MTCD Tools i can create custom action. For example: i've button for MUTE. If i remap button with MTCD Tools and assign Vocal Google Search to it the action is fine but MTCD became MUTE. There is a way to disable factory action and use only MTCD Action?
I have this problem too (no mapping option) but my steering wheel works on my Ford Focus. Check your CAN Bus box and make sure the model of it matches what's selected in Factory Settings. My CAN Bus box is a Raise 06, likewise it is selected in Factory Settings to match it.
@capu81 I am having this same issue with my doors on my Erisin ES6405V. Currently emailing with Erisin back and forth trying to get this fixed. If there is ever an outcome, I will let you know.
capu81 said:
Thank you to all for the answer.
The doors signal is not a big problem, l leave it in this way.
Steering Well remapping: with MTCD Tools i can create custom action. For example: i've button for MUTE. If i remap button with MTCD Tools and assign Vocal Google Search to it the action is fine but MTCD became MUTE. There is a way to disable factory action and use only MTCD Action?
Click to expand...
Click to collapse
I have same exact issue. Did you find a solution to it?
Hello, I have the exact same problem only the other way around, my steering wheel buttons are mapped and working, car is showing open/closed doors but for oil, rpm, speed battery nothing. I tryed messing with the canbus setup and change to other setting from VWto maybe get it to work but no luck. Any ideas on how I can solve this? I have a MTCD unit px3 2GB 7.1.2
I have also problem with CANBus decoder. The only problem is that when i drive and change shift activate rearview camera, all the other stuff (swc, door signals and also reverse enable the rear view camera) works fine. There is something like update or a settings that works fine. I have a FIAT Bravo model >2007 and in factory settings seems to be all ok
dirty_dty said:
Hello, I have the exact same problem only the other way around, my steering wheel buttons are mapped and working, car is showing open/closed doors but for oil, rpm, speed battery nothing. I tryed messing with the canbus setup and change to other setting from VWto maybe get it to work but no luck. Any ideas on how I can solve this? I have a MTCD unit px3 2GB 7.1.2
Click to expand...
Click to collapse
j0nnymoe said:
@capu81 I am having this same issue with my doors on my Erisin ES6405V. Currently emailing with Erisin back and forth trying to get this fixed. If there is ever an outcome, I will let you know.
Click to expand...
Click to collapse
These are not "problems" - CAN Bus support depends on your car model, the manufacturer of the CAN Bus box and whether MTC/HCT have written the software for these things. If youve played araound with all the CAN Bus settings and not every function works then there is nothing you can do . . . apart from get hold of the CAN Bus protocol for your vehicle,, the MTCD MCU protocl and then write and app for it. There are 1000s and 1000s of cars on the market (and 1000s no longer made) it would be far too costly to make full CAN Bus support for EVERY car on sale, so only the most popular cars are supported and even then not all models and/or all functionality.
@j0nnymoe - dont waste your time contacting Erisin, they are a seller not a manufacturer and theres nothing they will be able to do.
@typos1 do you think maybe it can be fixed if I update the MCU to the latest version? It just seam strage for it to work in open/closed doors but not for the rest, I'm thinking maybe a mismatch of canbus and software and maybe that is why it dose not work. (Just a wild guess)
dirty_dty said:
@typos1 do you think maybe it can be fixed if I update the MCU to the latest version? It just seam strage for it to work in open/closed doors but not for the rest, I'm thinking maybe a mismatch of canbus and software and maybe that is why it dose not work. (Just a wild guess)
Click to expand...
Click to collapse
Updating the MCU may certainly help.
@typos1 that is good to know, I can keep my hopes high for a bit longer but I am sceptic about the MCU update [email protected] gave me.. He did not test it and there is nobody else I could find that updated to the latest version of XRC to confirm it is the right one.
dirty_dty said:
@typos1 that is good to know, I can keep my hopes high for a bit longer but I am sceptic about the MCU update [email protected] gave me.. He did not test it and there is nobody else I could find that updated to the latest version of XRC to confirm it is the right one.
Click to expand...
Click to collapse
What do you mean "the right one" ?
If you remember on the other thread, he just attached a dmcu file of the latest MCU for my XRC unit and said he did not tested it.
dirty_dty said:
If you remember on the other thread, he just attached a dmcu file of the latest MCU for my XRC unit and said he did not tested it.
Click to expand...
Click to collapse
I cant see any reason to doubt him.
@j0nnymoe - dont waste your time contacting Erisin, they are a seller not a manufacturer and theres nothing they will be able to do.
Yea I gave up on that a while ago. I've had a couple of these units before from other sellers (xtrons/eonon) and the canbus on those units worked fine. I suspect the KGL unit's doesn't like my car for some reason. I toyed with the idea of getting another canbus decoder..maybe if I can get one cheap enough I might try it.
j0nnymoe said:
@j0nnymoe - dont waste your time contacting Erisin, they are a seller not a manufacturer and theres nothing they will be able to do.
Yea I gave up on that a while ago. I've had a couple of these units before from other sellers (xtrons/eonon) and the canbus on those units worked fine. I suspect the KGL unit's doesn't like my car for some reason. I toyed with the idea of getting another canbus decoder..maybe if I can get one cheap enough I might try it.
Click to expand...
Click to collapse
Did you try another canbus decoder?
I've got an a3 and I'm using a kgl unit and nothing shows on my dis screen on the dash but when I've had a unit from xtrons before that did work.. I'm guessing kgl must use cheaper canbus decoders and I've been thinking like you and we're thinking of buying another decoder from xtrons to try
I can`t find a working SDVC app for my PX5 GS unit. It is my second unit because the first has had a fault and was exchanged. On the first unit I used Graser´s Dasaita tool for volume control. On the new unit that isn´t working anymore and also MyMTCService does not recognise the unit as MTCD and so the sound control is not working.
The only thing that is different to the old unit are the connectors. The GPS connector uses now a Fakra plug, but I don´t think that this is a problem since all other GPS apps are working normally.
Neither Malaysk, the original GS ROM nor a HA ROM is working. I've tried also different MCU's.
Here you can see the problem with Grasers Dasaita tool. I am not driving and not changing the volume level: https://youtu.be/aT0asijim5g @Graser maybe you can help me?
Hi there:
Car is 2016 Nissan Qashqai J11 TS. I have installed a Wanqi HU Android 8 and after installing my steering wheels buttons stopped working. I changed the Canbus protocol to Xtrail/Qashqai but still unable to make the buttons working. Can anyone recommends me a way to solve this problem?
Best Regards
You should talk to the seller and have him confirm if the canbus is the one that corresponds to your Nissan model...
upload a photo with the code of the can bus, maybe some Nissan user can confirm whether it is correct or not, and in turn that protocol has worked well.
Try this:
https://www.youtube.com/watch?v=jM-VKUhaGUs
If it doesn't work, then probably you have something with can bus reading.
Hello ...
I have a problem with my eonon (klyde) px3 unit. Ever since I bought it, I have had a problem with usb ports.
When I use the USB dashcam and activate it, or when I use the USB flash disks from the speakers to listen to an electronic hiss, like electronic processing noise.. :crying:
If I turn the volume down to 0 the noise ends.
I tried to solve it like this:
- I replaced with new mtcd / mtce,
- I updated to the latest mcu version
- I flash mcu modified by wadzio( the audio sound is better, but the problem remains.)
- Eonon obviously tells me that it is normal to lower AMP to - 20 but the problem remains the same.
- I connected the chassis of the unit to the ground of the machine.
- I connected a 12v filter that is used in the car units of a good audio brand, to eliminate the hiss of the engine and alternator
Neither of these things solved the problems
Do you know if it is possible to install resistors, capacitors, or solve the problem with me or try to find it? Thanks
You are correct that the problem is a hardware issue and not software.
I dont own this variant, but willing to help - if I can get a unit sent to me, I could attempt to find root cause and develop a fix that could then be shared with the community.
marchnz said:
You are correct that the problem is a hardware issue and not software.
I dont own this variant, but willing to help - if I can get a unit sent to me, I could attempt to find root cause and develop a fix that could then be shared with the community.
Click to expand...
Click to collapse
Thanks ...
I have already changed the mtcd cardboard but nothing ..
- The problem is I have the px3 coreboard,
- Display management motherboard that interferes mtcd board,
- Mtcd motherboard badly designed
Hi everyone
I have a facelift 2010 Lexus IS250 F Sport, I've had some large success installing this XTRONS head unit for it and I am largely satisfied with it. I am however having an issue with getting Steering Wheel Controls to work with the head unit.
Lexus | Various | Android 10 | Octa Core | 4GB RAM & 64GB ROM | Integrated 4G Solution | PMA10ISLS
XTRONS PMA10ISLS is a 10.1" large screen car stereo with customized face panel and optimized CANbus Decoding for Lexus. It supports CarAutoPlay, built-in DSP, PIP mode enabled ,Dual Theme, Instant Rear Vision and so on.
xtrons.co.uk
Lexus| Various | ISO Wiring Harness | MOST
This ISO Wiring Harness is compatible with XTRONS custom fit units PSP10ISL,PMA10ISL etc. If your car is Lexus IS250/IS300/IS350 Convertible (2-door)with original navigation or fibre amplfier system,you need this cable to aid for the installation.
xtrons.co.uk
This is the unit I purchased, alongside a special wiring harness so that I could use it with my vehicle as its a facelift Navi.
With the default CANbus setting on my head unit, only Volume control seems to work and the phone call buttons and voice command buttons are mapped to functions like Radio and Hey Google but I cannot programme these on the app. With an alternative CANbus setting I get skip track functionality but I get different AC Controls and lose access to my factory amp settings.
The original wiring harness I got for the headhunt has not been used at all as I was instructed to usr the special harness, and that original harness had a CANBUS decoder. XTRONS claim that I am unable to programme the SWC due to the CANBUS needing to decode it, although I have played around with the settings and selected various different CANBUS settings.
Would anyone be able to advise me on how I can get the SWC working, would it involve plugging the CANbus decoder into the head unit? There is a 12 pin connection spare at the back but I am unsure if that would make the difference or not.