I've installed Bliss OS in VirtualBox. Most things run fine. WiFi is connected to 'VirtWiFi', and this gives me an Internet connection. However, when I try to access a Chromecast device in Google Home, it says, "Can't see [Chromecast device name] on this WiFi network". [Note: I tried to include screenshots of my WiFi settings and of the error message in Google Home. However, I didn't see a way to attach files, and since I'm a relatively new user, I'm not yet allowed to include hyperlinks.]
Is there another way to setup the network within VirtualBox, so that I can access Chromecast devices on my local network?
Thanks for any suggestions.
Related
Hello all:
(first of all, I apologize for the double post, I erred and replied to a thread in the diamond forum)
I'm having problems getting my remote desktop to work. Been trying to connect since I picked up my Fuze on the 11th.
I have three different computers that I can successfully administer via my desktop. I've tried using 3G to connect, no success. I've tried using Wi-fi to connect, no success. I've used local computer names, IP addresses, properly forwarded ports --
It has to be a setting I'm missing on the phone. Any ideas? TIA
What version of Windows are you trying to connect to? Do you have a Firewall? And have you done the port forwarding on the router?
But the only options you need is Computer: IP Address and the user name and password. Use a Domain if you are connecting to PCs on a domain. Also when I logged in not using 16bit color under options the PC was almost unusable.
My attempts
The things I have tried since my post:
1) attempting to connect to Windows Server 2003 machine, non-local. Used IP address with port, same IPort that works from my desktop. Left username/password blank -- filled them both in -- left the domain name blank -- filled it in. All failed. Get the error message with three possible causes listed. Connected to my home network via wifi, data connection disabled (sometimes causes problems with my internet browsing if they're both enabled)
2) attempted to connect to a local machine, running XP Pro. Again, tried all possible combinations of username/password completeness, no success. Using Wifi
My local router does have a firewall, and the remote router does as well. I can successfully navigate those using my desktop (or laptop, for that matter)
GTO: I appreciate the quick reply...thank you.
3daysaside said:
The things I have tried since my post:
1) attempting to connect to Windows Server 2003 machine, non-local. Used IP address with port, same IPort that works from my desktop. Left username/password blank -- filled them both in -- left the domain name blank -- filled it in. All failed. Get the error message with three possible causes listed. Connected to my home network via wifi, data connection disabled (sometimes causes problems with my internet browsing if they're both enabled)
2) attempted to connect to a local machine, running XP Pro. Again, tried all possible combinations of username/password completeness, no success. Using Wifi
My local router does have a firewall, and the remote router does as well. I can successfully navigate those using my desktop (or laptop, for that matter)
GTO: I appreciate the quick reply...thank you.
Click to expand...
Click to collapse
Okay its been awhile since I used 2k3 sever. Using 2k8 lately but are you trying to use Terminal Server? and if your using 2k3 and you have ISA enabled I know it can be a pain to do port forwarding with it. But let me get this stright. You have no issues using XPs Remote Desktop to log into the server machines Terminal Server/Remote Desktop? Here is an idea. Whatever port your running Terminal Server/Remote Desktop type the IP Address with a : and port. IE 192.168.0.1:3000
Also if you would like you can PM the IP address of one of the Machines and I will try from my phone that I know is working with my machine. I am pretty sure you don't need to end a user name or password and it will bring me up to the login screen or you can make a temp account. On also on the Win2k3 machine I am pretty sure you have to add the option to login with Terminal Server even if its the Administrator account.
I am able to connect to my local XP machine over wifi using the ip addy/no port. Hostname (DNS) connection attempt failed, though. My 2k3 server's power supply died or I would test that for you.
No special router config (port fwd) for my device had been done.
The fact that you can't get to your local box on your local network is where I'd start.
Local Network Issues
Thanks again to you both...
I think that might be the problem -- the local network setup. I can connect via wifi, and browse the web. However, I can't install a network printer using the WinMo app that's included, and I can't seem get to the local PC even when I use the local IP instead of the DNS name. I did check, I'm being issued an IP address by the router (obviously), but still no dice on anything relating to network based traffic.
Is there a way to ping using WinMo? I'd like to be able to use that start.
Cont..
Also, I've noticed that I don't get the same error each time. Depending on which machine I'm trying to connect to, it'll give me an error with either two or three options as to why it's not working. Trying to figure out what that's telling me.
As far as Terminal Services are concerned, when I connect from the desktop, I believe I'm using Remote Desktop there (honestly, I haven't been paying attention -- I just use whatever pops up when I type 'mstsc' from the Run dialog, lol), and I can connect to the 2003 server. However, I can't play with this anymore today, because apparently the server is down, and I won't be able to get to it till Monday.
I think I'm going to go play with the ATT proxy and see if that changes anything. I think mine is still enabled because I read that it might help with the GPS problems...
I have found some freeware app... pocketping 1.6 and microsoft has a network tool offering which I am not sure will work on WM6. I have no exp. with either tool on WM.
Can you get to your http/https router mgmt interface from the device? Check your router's client table? Does your router have any logging capabilities?
Sorry, more questions than answers.
Router
I am able to "dial" into the router from my phone -- it shows the HTCP4600 in the clients table with an IP of 192.168.2.108 ... all good.
My logging on the router was disabled, but now it is enabled. What should I be looking for?
I think i'll try the pocketping...
Now make sure inside of the router then you have all the correct ports forwarded.
It should be port 3999 to 3999 On UDP and TCP and then your PC ip behind the firewall.
Pocketping, JETCET Print 5, and success
Here's the update:
Discovered that by disabling the AT&T proxy on the Fuze, I was finally able to connect to my network printer -- the Fuze doesn't have the drivers for my printer, but that's another thread.
So I was able to make my first IN-Network contact. Installed pocketping 1.6, and it's a very useful tool. I'm able to successfully ping the computers on my network now that the proxy is disabled -- an voila...I can also connect to my laptop on my own network! The main trick was to use the network IP address and not the DNS name.
Thanks to both of you who helped out.
Hello This guide is made up from the knowledge i have build up from advice given on XDA and information on other sites.
I have found this very useful in my home and hope you do to.
First off, this guide explains everything you need to do to use your diamond as the access point to the internet at home for all devices. (PC's, PS3, XBOX360, Wii)
It is highly recommended that you have a unlimited data allowance!!!!! Otherwise you could have a hefty bill at the end of the month.
Right what you will need :
A WM6.1 Device (I used a Diamond) with an unlimited data allowance tariff,
A WiFi router (i have used an old router that was installed with Tiscali BB)
WMWifiRouter version 0.80 (please find this your self i will not provide it)
and some basic knowledge of networking on PC's and your devices.
Thats it. Please don't be put off by the networking side of things its really easy to do.
Right first off we need to get your diamond taking to your router.
switch on your router and let it do its thing for 2-4 mins
Connect your diamond to the wifi router by switching on your wifi in settings, communications on touchflow, when prompted, connect to your router and enter your network key.
THIS IS THE SAME PROCESS AS CONNECTING TO A WIFI HOTSPOT.
Its that simple.
Next switch off your wifi in settings, communications.
Install WMWifiRouter version 0.80 (Simple and stable)
once installed open WMWifiRouter and press connect.
This should then setup your phone to be used as a access point and connect to your wireless network all at once.
Once it says connected you can turn off your phones main screen by pressing the off switch at the top and put your phone where there is best signal! HSDPA is needed to get up 7.2mbps (little H in signal area)
Right now you need to setup your laptop or device to talk to the phone via your router!
So here are the settings you need to setup in either TCP/IP (manual connection) or a manual connection on your device (PS3, Wii, XBOX360).
I will use a laptops connection as a example because all you need to do is to copy the settings to another device using a different IP address.
If you use wifi or a hardwired connection, right click the telly with the wifi connection in the bottom right of the screen and click open network connections (XP only dont know for vista), Or if the telly is not displayed in the bottom righthand cornner of the task bar then click start, control panel, network connections.
Click on the connection you wish to use i.e local area connection or wireless network connection (you can setup both connections by repeating these steps on each connection)
this should bring up a general tab of this connection, click properties.
This will bring up another box with the network properties, all you need to do is manually enter your IP settings and DNS settings so double click on "internet protocol [TCP/IP]"
Another box appears.
Click "use the following IP address"
In IP address type "192.168.0.xxx" xxx being the unique 3 digit code of your choice, write this down for your firewall settings on other devices if you run a networked drive etc. Each new device will need its own unique 3 digit code ie PC = 192.168.0.100, XBOX360 = 192.168.0.200, Wii = 192.168.0.123 etc.
In Subnet mask type "255.255.255.0"
In Default gate way type "192.168.0.1
Now click "Use the following DNS server address"
In preferred DNS server type "192.168.0.1"
Thats it, press ok and ok on any other boxes still left open.
Your network device will rest your IP and DNS settings to the ones you have just entered, thus allowing you computer to access the mobiles phones internet connection via your router
On all your devices Manually setup all your connections using these settings and they will all use your mobile phone to connect to the internet.
Using DHCP to configure your network is not advised as its unreliable at finding your phones connection.
Now if you want to start using your phone as a phone again, open up WMWifiRouter again if its not already and click options Quit.
To get internet access on other devices via your phone again all you need to do is to start WMWifiRouter and press connect. Start using the internet!!!
If you wish to use your laptop on another hotspot, you will need to reset the TCP/IP settings back to automatic, otherwise it will not work.
Using this process sometimes causes the phone to disable its own internet connection, so a soft reset after exiting WMWifiRouter is recommended.
Have fun, im sorry if its all a little messy but i have never been very good at writing these guides.
If any modd wants to add or edit this post then please feel free. any persons wanting to add to this guide please do so.
Yes i know you can connect your phone to your laptop by USB, Bluetooth, but this method allows multiple devices to use the same phone to access the internet at the same time and via a access point at the highest possible speed, so games consoles can use it!!! Brilliant if you get a good HSDPA signal and live in the country.
Oh one last thing! if you are a youngster and wish to try this, please do so on other equipment, don't use your family's main router and laptop or PC unless its no longer in use!!!
Thank You
Hello. I am having a Sony Ericsson Xperia X1 WM6.1 Device. Recently, I've tried internet sharing via USB and it doesn't seem to work. My idea is to be able to have internet connection on my phone via USB that connects to my main computer that has ADSL connection.
After pressing 'Connect' is successfully connects but any internet usage I've made is via my EDGE connection, not ADSL.
According to Windows Vista Internet Sharing Center, my phone's network access is 'Local only' as apposed to my normal LAN connection which is 'Local and Internet'.
I've searched for a solution and I came to this http://support.microsoft.com/kb/928233 but it still does not work.
Apart from the problem of Internet Sharing, my WMWifiRouter can't seem to work also.
As far as I know, WMWifiRouter will need to have Internet Sharing to work first, so it's normal that it is not working. However, I found a rather interesting message whenever I connect the 'USB to WiFi' mode. A pop up box with the tile 'Pocket PC Networking' will say ' cannot obtain a server assigned ip address. try again later or enter an ip address in network settings'.
Can anyone share with me the proper IP address for WMWifiRouter on my PC and on my WM device?
Anyway, just to describe the problem I'm facing when I'm using WMWifiRouter.
1. I connect 'USB to WiFi', everything seems to work fine, the status is ready.
2. I can see my own network name on my laptop.
3. I click on it, and the message shows connected.
4. Tried to access the internet but it won't work.
So, the main problem now is...
1. There's something wrong with Vista causing any device that wants Internet Sharing to only connect to 'Local'
2. There's something wrong with my IP configuration.
Thank you all very, very much in advance for helping me out.
unless chainfire beats you to it and posts the answer here.. you can PM him
Alright, thank you very much for your suggestion!
There are a lot of WiFi server apps in the market, e.g. Swiftp (swift ftp).
The app should be run on either the TF or your android phone (some of these things work on iphones too i think) and then you either type in an http192.168.1.3:8080 or similar into the web browser to connect to the other device as a file manager OR,
you get given an FTP:// address by the app which you need an FTP client for on your device (again there are plenty in the market e.g AndFtp).
This should allow you to use WIFI to browse the other device's files and transfer things between them.
I have my phone and TF connected to my home router, one is 192.168.1.3 the other is 192.168.1.6 for the IP's but whatever apps i try or anything I do I cannot get them to connect to each other. I just get "host not found" or "connection error".
How can I get this to work?????
I want to connect my android device (nexus 7 2013) to an openvpn server which is not administrated by me, meaning I have no access on the configuration.
On my windows7-pc, I do this with the windows version of openvpn, the provided settings file for the openvpn server and the also provided pem-certificate.
Since the server uses the tap device of openvpn, alternative clients like openvpn for android by arne schwabe[1] don't work (this app doesn't support tap).
Since I don't have a private key file (*.key), I cannot generate a p12-file[2] which could be imported by the official openvpn app[3].
The pem-fileformat is compatible to *.cer and *.crt, meaning, I can simply change the file extension to "convert" them. The crt-file can be imported by the android systems (security -> import), but this doesn't help openvpn as it seems to only use it's own certificates.
Any suggestions on how to achieve a successful connection?
[1]: play.google.com/store/apps/details?id=de.blinkt.openvpn
[2]: blog.max.berger.name/2010/01/pem-fromto-p12.html
[3]: play.google.com/store/apps/details?id=net.openvpn.openvpn
wifi
i think if you have ICS_P740AV1.0.0B07 + you can't find open hot spot and if you can see you can't connect.
Try to make one hostop secured with wpa2 and try it.
k0tsompakos said:
i think if you have ICS_P740AV1.0.0B07 + you can't find open hot spot and if you can see you can't connect.
Try to make one hostop secured with wpa2 and try it.
Click to expand...
Click to collapse
Whoa, i only understand half of it
I have android 4.3 JSS15Q rooted with flo (?). I have superSU and Busybox installed. I followed the default instructions of the nexus root toolkit. My wifi is connected for sure, but it has blocked ports (which is the reason for all this). However, since I'm failing at an earlier stage, and, since it works from my pc from the same network with the same openvpn on the same ports I suppose the error is not in the network settings...
The wifi i'm connected to has wpa2+pkip etc. but I'm not sure how this is relevant...
rom
you have installed a custom rom?
you have try to enable and disable airplane mode?
you have data conenction?
k0tsompakos said:
you have installed a custom rom?
you have try to enable and disable airplane mode?
you have data conenction?
Click to expand...
Click to collapse
I have stock android rooted. I only have wifi and the connection works perfectly, I tried rebooting the device, I consider this counts as "dis/enable airplane mode". I have good wifi signal strength.
I have no issues accessing websites over port 80/443, only the blocked ports don't work. The openvpn server is reachable on port 443 (it works from my pc).
Hello,
did you ever manage to solve this? I'm looking to configure my nexus 7 2013 to connect to an OpenVPN server using TAP and it doesn't seem to be working. I'm using OpenVPN settings with certificate-based authentification. I'm able to connect to my server, however I don't get a local IP address assigned and when I browse the internet, my IP is still showing up as from the original connection instead of the VPN endpoint. Computers with windows 7 can connect to the server no-problem and all their traffic is directed to the tunnel. Any ideas for guides and walkthroughs?
Thanks. Any help is very much appreciated.