I followed this guide [GUIDE] MAC Rooting Nexus S (http://forum.xda-developers.com/nexus-s/general/guide-mac-rooting-nexus-s-t878446) until point
6) Open ROM Manager and choose "Flash ClockworkMod Recovery". At this point you are all set .
Click to expand...
Click to collapse
As Rom manager rebbot doesn't work, I installed Root checker and it told me thet the phone was not rooted properly. So I decided to follow another guide [HACK] Superboot Method for 2.3.2 (GRH78C) (http://forum.xda-developers.com/nexus-s/development/hack-superboot-method-2-3-2-grh78c-t927838).
Now the phone doesn't work! In other words when I press the power button the Google logo screen remains and Android doesn't start.
If i hold volume up and power button I gain the following:
Code:
Fastboot mode
Product name: Hearing
Hw version - rev 52
Bootloader version - I902XXLC2
Baseband version - I902XXKI1
Carrier info - EUR
Serial number - 3035...
Lock state - unlocked
and I can choose:
Code:
[LIST]
[*]Reboot bootloader
[*]Reboot
[*]Recovery
[*]Power off
[/LIST]
I think that the problem is that the phone is looking for the file "install-recovery.sh" that I renamed into "install-recovery.sh.old".
How can I reanimate my Nexus S?
Nicolaesse said:
I followed this guide [GUIDE] MAC Rooting Nexus S (http://forum.xda-developers.com/nexus-s/general/guide-mac-rooting-nexus-s-t878446) until point
As Rom manager rebbot doesn't work, I installed Root checker and it told me thet the phone was not rooted properly. So I decided to follow another guide [HACK] Superboot Method for 2.3.2 (GRH78C) (http://forum.xda-developers.com/nexus-s/development/hack-superboot-method-2-3-2-grh78c-t927838).
Now the phone doesn't work! In other words when I press the power button the Google logo screen remains and Android doesn't start.
If i hold volume up and power button I gain the following:
Code:
Fastboot mode
Product name: Hearing
Hw version - rev 52
Bootloader version - I902XXLC2
Baseband version - I902XXKI1
Carrier info - EUR
Serial number - 3035...
Lock state - unlocked
and I can choose:
Code:
[LIST]
[*]Reboot bootloader
[*]Reboot
[*]Recovery
[*]Power off
[/LIST]
I think that the problem is that the phone is looking for the file "install-recovery.sh" that I renamed into "install-recovery.sh.old".
How can I reanimate my Nexus S?
Click to expand...
Click to collapse
Find wuggs Nexus Root Toolkit... Read the thread and you'll have your phone back..
Sent from my OnePlus ONE
Setting.Out said:
Find wuggs Nexus Root Toolkit... Read the thread and you'll have your phone back..
Sent from my OnePlus ONE
Click to expand...
Click to collapse
Thanks, which is the option to choose?
I think 5 and then 3.
After reanimating the devide I'd like to install Kit Kat version of Android on it so I need a rooted smartphone.
1. Unlock the Bootloader
2. Flash ClockworkMod/TWRP Recovery
3. Root the Device
4. Lock the Bootloader
5. Flash Google Factory Image
6. Donate
0. Exit
Click to expand...
Click to collapse
Nicolaesse said:
Thanks, which is the option to choose?
I think 5 and then 3.
After reanimating the devide I'd like to install Kit Kat version of Android on it so I need a rooted smartphone.
Click to expand...
Click to collapse
I'm going to put it step by step using the Nexus root tool kit (NRTK)
1. download a flashable recovery of your choice (CWM 6.0.4.3 Philz 6.19.3 or TWRP 2.7.0 or higher on all these)
2. download the kitkat rom you want to install
3. download the Gapps that match the rom you chose ( if a 4.4.2 rom get a 4.4.2 gapps if 4.4.4 then 4.4.4)
4. boot your phone into bootloader / fastboot
5. connect your phone to your pc (it should recognize it)
6. open your NRTK and go to the advanced section and choose to temporarily boot custom recovery (this will be TWRP 2.6.3)
7. ON YOUR PHONE select mount usb
8. ON THE COMPUTER open the device/folder for your phone and create a new file on your SD card ( I called mine " !zip " this kept it ontop of the list of files) and copy the recovery, rom, and kernel to this folder.
9. ON YOUR PHONE unmount usb, return to the main menu screen and select install, find that folder you made and select the recovery zip that you copied and swype to install
10. after it installs (10seconds) return to the main menu, select reboot then reboot recovery ( you may get a warning about not having a rom or su, ignore both)
11. now you are on your KK compatible recovery (nearly there)
12. No matter which recovery you chose find the section to wipe or format your phone (DO NOT WIPE OR FORMAT YOUR SD CARD !!!! this will wipe everything off your phone and may make it hard / impossible to restore) and ONLY wipe or format system, cache, and dalvik partitions. On philz there is an option to wipe to install a new rom (this is a onestep version of the above)
13. return to the main menu page and select install, choose your rom and install, then your gapps and install ( if on TWRP you can select both by choosing the option to add a zip to flash)
14. the moment of truth, now that you have flashed both rom and gapps, you need to return to the main menu and select reboot and reboot system...
15. assuming you did all of this issue free, you are free to enjoy your phone..
*if you don't have your phone recognized by your computer / NRTK, you need to follow the instructions for NRTK to get the correct drivers for your computer
**if you are not clear on what you are doing, ask before you make a mistake
***Your custom rom will be pre-rooted, so no need to try to root it
KINDLY DISABLE LOCK SCREEN PATTERN OR PASSWORD BEFORE STARTING THE PROCESS!!!
This is official Chinese STOCK ROM provided by YCJESON and modded by MANOJ NAIR for indian variant(x526) of the LeEco Le 2
Step 1: * Click Here * and download all necessary files provided by that guy !!
Step 2: follow this if custom recovery is not installed or else skip this step to next
(This will encrypt all your data in internal memory with unknown password so do backup your data before doing anything)
go to settings ->then about phone ->then tap on the build number few times until you dont see *YOU ARE NOW DEVELOPER*
go back there will be new option above *about phone* which is *Developer Option*
now go into that setting and enable *OEM Unlocking* and *USB Debugging*
now power off the device and boot into *fastboot mode*
TO BOOT IN FASTBOOT MODE SWITCH OFF YOUR DEVICE & THEN PRESS POWER BUTTON & VOLUME DOWN BUTTON TOGETHER FOR FEW SECONDS!
Download 15 seconds ADB Installer v1.4.3 from * Here * and
Run it (Require administrator privileges)
Press Y/Yes to install ADB and Fastboot or N/No to skip
Press Y/Yes to install ADB system-wide or N/No for current user only
Press Y/Yes to install Drivers or N/No to skip
Continue Driver installation
finished!
now connect your phone to PC while you are in FASTBOOT MODE and
in PC open CMD in folder you have placed all those file you have downloaded in STEP 1
you can press and hold shift key and press right mouse button in the folder to get new Open Command Window Here option in right click options
Now type commands in cmd which is given below
to check if phone is detected by PC or not type command given below
fastboot devices
if not detected by pc then download and install drivers * click here * to download it
if device is detected then type this command to unlock your bootloader
fastboot oem unlock-go
type this command to check if device bootloader is unlocked or not
fastboot oem device-info
now its time for real fun flashing custom recovery then format data besides advance wipe to recover phone from encrypted data issue
?
Step 3: in fastboot mode press & hold power and volume up button together in fastboot mode to switch to recovery mode which we just flashed in Step 2
first do wipe the system to factory reset (dont know but may be you should better backup internal data & format it too, #justIncase)
here you will have to do full ROM backup for safety
now go to mount and press enable mtp so you can see internal storage in your PC now
copy X526_EUI5.9_20S.zip from download folder to your phone
now go to install and select zip you just copied (make sure you did factory reset before this procedure)
after flashing this ROM flash Lazy Flasher zip file for permanent fix for internal data loss issue [emoji14] * click here * to dowload
you can flash Supersu zip file from install to root this rom
?
Step 4: its that simple enjoy new ROM & ya thanks to LeEco for awesome ROM & YCJESON and also MANOJ NAIR for making this ROM available for our le2 x526
no need to flash gapps as playstore and google play service is installed by default so
just download google apps you require from play store
Click Here for Video Tutorial By DragonDROID
*(This is only how to install tutorial so for Custom Recovery pls follow step 2 first)
New Features:
1. Quick Ball- activate it from Accessibility by enabling intelligent assistant
2. Fingerprint Navigation eg. Tap FP to open control center, notifications,double tap FP screen lock ,swipe right - left for more function
3. Theme Store-In Personalize if you click online themes it opens Theme Store Now
4. Wallpaper Application
5. LeTouch Shutter - open camera directly while display is off & is in lockscreen mode
6. Battery Assistant - new smart mode & ultra mode for battery saving
7. Phone Manager - updated new version
8. Faster Fingerprint detection then eui 5.8.19s indian version
9. Battery Life seems improved, Screen On time is now 5 hour and around 15-16 min (max what i got was 5 hour 30min which was 4 hour 30min before in 5.8 ROM & thats what i have seen far )
FIX:
XPOSED INSTALLER Launcher Crash Fix:
1). boot to recovery
2). mount system
3). delete /system/priv-app/Launcher3/oat folder (or move to Internal Storage as Backup Plan just incase)
4). reboot
this should solve xposed installer issue !!
Greenify Auto-hibernation stopped Fix:
Greenify - Works Perfectly ! (but need to fix it to make it work perfect and blame is on EUI see below for why)
here is what you need to do for greenify to work perfectly
1). go to settings -> accessibility -> enable greenify service there
2). open phone manager app -> goto power saving management -> App Protection -> enable greenify there
3). go back to main screen of phone manager -> goto Security and Privacy -> Manage auto launch -> enable greenify there too
4). open Greenify -> Setting -> Trubleshooting -> Auto-hibernation -> enable Service Guardian
5). voila !! you are good to go with fully functional greenify app
Waiting for WiFi even after Data is turned on Fix:
1). go to download app in system tool
2). then go to setting and set it to *no limit* instead of *do not allow downloads*
3). this will fix your sim data download issue
btw its not bug its feature
19S Like Statusbar MOD:
x). click here for 19s like Status Bar mod by @tazzysingh1731
y). also added MOD to original mediafire link
Added Poll but i messedup with title as i typed Easy Twice just ignore *it Easy* lolzz :silly:
it was supposed to be *is this tutorial easy ??*
What about gapps ? Is it included in the ROM?
ajo81 said:
What about gapps ? Is it included in the ROM?
Click to expand...
Click to collapse
Just play store...
ajo81 said:
What about gapps ? Is it included in the ROM?
Click to expand...
Click to collapse
no need to flash gapps as playstore and google play service is installed by default so
just download google apps you require from play store
New
any 1 installing XPOSED FRAMEWORK on this rom make sore use any other launcher and make as defalt launcher before the xposed install and dont use eui launcher other wise its force close
hear is the fix http://mkgdroid.blogspot.in/2016/11/fix-launcher-stopped-working-issue-on.html
commgo said:
New
any 1 installing XPOSED FRAMEWORK on this rom make sore use any other launcher and make as defalt launcher before the xposed install and dont use eui launcher other wise its force close
Click to expand...
Click to collapse
FIX for this issue is added now :highfive:
Will this work for the Le S3 x522?
Tried on Le S3 x522. Did not wipe data. Just directly upgrade. Everything works fine except playstore failed to launch. Always displaying failed to retrieve information from server. Any ideas how to fix it?
myasus said:
Tried on Le S3 x522. Did not wipe data. Just directly upgrade. Everything works fine except playstore failed to launch. Always displaying failed to retrieve information from server. Any ideas how to fix it?
Click to expand...
Click to collapse
Have you tried clearing playstore data?
Posted using a calculator and delayed by AT&T.
myasus said:
Tried on Le S3 x522. Did not wipe data. Just directly upgrade. Everything works fine except playstore failed to launch. Always displaying failed to retrieve information from server. Any ideas how to fix it?
Click to expand...
Click to collapse
please do confirmation about this, if it is really working on your device
pls send screenshot as confirmation
and try clean install and see if playstore issue is fixed or not !! :fingers-crossed:
It is working after re-flash. No need to clear data. Everything works fine now. Had to re-flash xposed framework in recovery.
Good things for this rom is we can select which Sim for data in setting, not limited for Sim 1.
myasus said:
It is working after re-flash. No need to clear data. Everything works fine now. Had to re-flash xposed framework in recovery.
Good things for this rom is we can select which Sim for data in setting, not limited for Sim 1.
Click to expand...
Click to collapse
Great ! Can you just provide Screenshot of your about phone so i can officially add it to OP that it is also flashable to this device too :fingers-crossed:
TechGeekD said:
Great ! Can you just provide Screenshot of your about phone so i can officially add it to OP that it is also flashable to this device too :fingers-crossed:
Click to expand...
Click to collapse
Here u go:
download link not working!
ajo81 said:
download link not working!
Click to expand...
Click to collapse
Retry Now Download Link is updated
myasus said:
Here u go:
Click to expand...
Click to collapse
Awesome this means Le 2 x526 & Le S3 x522 shares almost same source code !! :highfive:
TechGeekD said:
Retry Now Download Link is updated
Click to expand...
Click to collapse
thank you ..but please update link in your xda post .
ajo81 said:
thank you ..but please update link in your xda post .
Click to expand...
Click to collapse
FIXED :fingers-crossed:
Will this work on x522 US version ?
Sent from my Le X522 using Tapatalk
rfresh said:
Will this work on x522 US version ?
Sent from my Le X522 using Tapatalk
Click to expand...
Click to collapse
as @myasus have already successfully flashed this rom to Le S3 may be yes you can too see above for his post with screenshot :fingers-crossed:
Hello, today I'll be guiding you to how to install LineageOS or other GSI ROMs on your A127F U7 device.
First, some precaution:
Rich (BB code):
/*
* knox_warranty_void: 0x01
*
* Your warranty is now void.
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or your getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
*/
Requirements:
Code:
* Unlocked bootloader
* Your device's firmware
* Android's platform tools.
* Magisk
* Odin
* U5, U6, U7 TWRP
* GSIs Image for the ROM you want to download
* physwizz's kernel
1) The first step you want to do is, unlock your bootloader. You can simply do that by enabling OEM Unlocking in Developer settings, (Can be unlocked by going to Settings > About Phone > Software Information > tapping "Build Number" 5 times then booting to download mode. (Connect to PC, shutdown your phone, then hold volume up and down buttons, then when you're on the download screen, hold volume up., then press volume up again) WARNING: THIS WILL ERASE YOUR DATA AND PERFORM A FACTORY RESET, SO BACKUP YOUR DATA WHEN NECESSARY.
2) Then, download the firmware you have for your firmware. How? Try visiting sites like samfw and find your firmware by searching A-127F and finding your country's baseband. Then download through your preferred method of downloading. Mine I login to Google, and downloaded through Google Drive, which is faster. (Though it will personally copy the firmware's file to you Google Drive and occupy space on it, so beware of that and delete the file afterwards, the file is in DRIVE > samfw_temporary_folder_dont_delete I assume it's safe to delete after download, so there's that.)
3) Extract the file, and adb push the AP_XXXXX file to your device. How? Download the Android platform tools to the above hyperlink, then extract it, go to the file and then type: e.g adb push [DIRECTORY WHERE YOU EXTRACTED YOUR FIRMWARE FILE]\AP_XXXXXX, [FILL IN THE FILE NAME] /sdcard/
4) Then boot up your device, set it up (minimally), download the magisk from below, (25.1-delta file) then install it. Then from the app, select Install Magisk > Patch from File then select the AP_XXXX file you've extracted from your firmware. Wait, for some minutes, and then see what is the file name.
5) Then pull the file and flash with Odin. (Download below) Use adb pull /sdcard/Download/magisk_patched-XXXX [See the magisk log for the file name] C:\Users\[your user]\Downloads\. Open Odin, select okay, when prompted, select AP, select the magisk_patched-XXXX file you've extracted from your phone, untick auto-reboot, then hit flash.
6) Go to stock recovery, again by pressing Volume Down +Power, then while connected to the PC, press Volume Up + Power then navigate via volume buttons and then press with power button, Wipe data/factory Reset
7) Turn off the phone (while connected to the PC) by pressing Volume Down + Power, then when turned off immediately press Volume Up + Volume Down. Go back to Odin, download the TWRP image below, and put it in AP slot and untick auto reboot. Then flash
8) Boot to recovery, by again Volume Down + Power, when turned off, Volume Up + Power, whilst connected to PC. ( See 6.) Now you've booted to TWRP Recovery. Go to Advance > Terminal then type multidisabler twice. (Very important)
9) Then download the GSI ROM you want to flash, extract it, then adb push it to your /sdcard/, just as you did with 3. (Here is a list of GSI's you can download) (Optional) Either use MTP or adb push to get into your device physwizz's kernel, and GApps (the guide will be in the second post, yet to find a way how to install it)
10) In the recovery, select Install > Install Image > select the GSI ROM's .img file you have, and select System Partition. (Optional) Then select Install Zip Then install physwizz's kernel.
11) Then, reboot, WAILA! There you have it, your own GSI ROM on your A127F U7 device. Enjoy
Credits: @physwizz, for his recovery and kernel ports. Without his hardwork, it wouldn't even be possible to install GSI for U7
How to install GApps.
Method 1 (tested and worked):
Download the A/B Google Apps VNDK Secure variant of Lineage. (In AndyYan's sourceforge page it would be bgS-vndk-secure):
extract the file as usual, and then rename the file as system.img.
Download the attachment below.
adb push both files to your /sdcard/ or any folder you prefer within /sdcard. (Though the files must be in the same directory) i.e. adb push system.img ChonDoe_Flasher.zip /sdcard
Go to TWRP > Install then select the ChonDoe_Flasher.zip,
and WAILA, you have now a working LineageOS with Gapps, it might work with other ROMs too!
Method 2, will post when I have tested it.
Credits: @chondoe for his flasher
--- Theory for flashing twice (disproven, you only need to flash once, here for archive purposes, you don't need to read it if you're not interested):
Go to TWRP > Install then select the ChonDoe_Flasher.zip, TWICE. Do not reboot only doing it once, or else it might bootloop. After flashing once, go back and then do it again. (If you accidentally did it once, tell me if it worked and I'll post the results)
(EXPLAINED: This is a theory of mine, though, I didn't test doing it only once, I'll try to do it once if I ever go back to stock ROM and see if it only requires once, but as of now I tried doing it twice and it worked [the logic behind this is, if you install the .img alone, it will boot-loop due to lack of storage, but the flasher uses e2fsck and resize2fs so along the process, it expands the file system and thereby allowing more space for installation. I theorize doing this once will not work because the script first installs/flash the .img before using e2fsck and resize2fs and therefore still lacks the file system space that it needs to boot, but if you do it twice, you will have already executed the two binaries and thereby allow space for a proper installation of the .img, so it will now boot and not get stuck on an infinite bootloop.])
My phone keeps bootlooping, i followed the tutorial strp by step, can you help me?
MaybeFazat said:
My phone keeps bootlooping, i followed the tutorial strp by step, can you help me?
Click to expand...
Click to collapse
Can you remember what firmware you had? Are you sure it's the right one for your device? Also, this is for A127F U7, make sure your device is compatible. Consequently, what GSI ROM have you flashed? This method only worked with LineageOS 19.1. bvS (by AndyYan). If the bootloop doesn't show the lineage logo, it may be that the GSI file is too big for the system partition, I have yet to found a way to expand our device's /system partition. Try AOSP 12.1 first, or download LineageOS 19.1 bvS from AndyYan's page, and see if it works.
Here https://sourceforge.net/projects/an...20221011-UNOFFICIAL-arm64_bvS.img.xz/download
juliano-oh! said:
Can you remember what firmware you had? Are you sure it's the right one for your device? Also, this is for A127F U7, make sure your device is compatible. Consequently, what GSI ROM have you flashed? This method only worked with LineageOS 19.1. bvS (by AndyYan). If the bootloop doesn't show the lineage logo, it may be that the GSI file is too big for the system partition, I have yet to found a way to expand our device's /system partition. Try AOSP 12.1 first, or download LineageOS 19.1 bvS from AndyYan's page, and see if it works.
Click to expand...
Click to collapse
Alright thanks for the info
Good work
juliano-oh! said:
Can you remember what firmware you had? Are you sure it's the right one for your device? Also, this is for A127F U7, make sure your device is compatible. Consequently, what GSI ROM have you flashed? This method only worked with LineageOS 19.1. bvS (by AndyYan). If the bootloop doesn't show the lineage logo, it may be that the GSI file is too big for the system partition, I have yet to found a way to expand our device's /system partition. Try AOSP 12.1 first, or download LineageOS 19.1 bvS from AndyYan's page, and see if it works.
Click to expand...
Click to collapse
And also, what gapps i need to use?
MaybeFazat said:
And also, what gapps i need to use?
Click to expand...
Click to collapse
That's what I'm currently struggling with, I can't find a GApps that work with any GSI since the /system partition is too small to even install GApps. There are critical and hard to follow tutorials out there that helps with increasing the /system parition but I have yet to try them since it, as I am informed, can hard brick your device. So I'm very cautious about that. @physwizz just recommends installing a ROM with GApps already installed in it (such as Pixel Experience) but I have yet to try that either.
MaybeFazat said:
And also, what gapps i need to use?
Click to expand...
Click to collapse
I accidentally duplicated my reply, sorry
juliano-oh! said:
That's what I'm currently struggling with, I can't find a GApps that work with any GSI since the /system partition is too small to even install GApps. There are critical and hard to follow tutorials out there that helps with increasing the /system parition but I have yet to try them since it, as I am informed, can hard brick your device. So I'm very cautious about that. @physwizz just recommends installing a ROM with GApps already installed in it (such as Pixel Experience) but I have yet to try that either.
Click to expand...
Click to collapse
Can you try magisk gapps?
juliano-oh! said:
Hello, today I'll be guiding you to how to install LineageOS or other GSI ROMs on your A127F U7 device.
First, some precaution:
Rich (BB code):
/*
* knox_warranty_void: 0x01
*
* Your warranty is now void.
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or your getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
*/
Requirements:
Code:
* Unlocked bootloader
* Your device's firmware
* Android's platform tools.
* Magisk
* Odin
* U5, U6, U7 TWRP
* GSIs Image for the ROM you want to download
* physwizz's kernel
1) The first step you want to do is, unlock your bootloader. You can simply do that by enabling
Code:
OEM Unlocking
in Developer settings, (Can be unlocked by going to
Code:
Settings > About Phone > Software Information > tapping "Build Number" 5 times[\CODE] then booting to download mode. (Connect to PC, shutdown your phone, then hold volume up and down buttons, then when you're on the download screen, hold volume up., then press volume up again) WARNING: THIS WILL ERASE YOUR DATA AND PERFORM A FACTORY RESET, SO BACKUP YOUR DATA WHEN NECESSARY.
2) Then, download the firmware you have for your firmware. How? Try visiting sites like samfw and find your firmware by searching [CODE]A-127F
and finding your country's baseband. Then download through your preferred method of downloading. Mine I login to Google, and downloaded through Google Drive, which is faster. (Though it will personally copy the firmware's file to you Google Drive and occupy space on it, so beware of that and delete the file afterwards, the file is in
Code:
DRIVE > samfw_temporary_folder_dont_delete
I assume it's safe to delete after download, so there's that.)
3) Extract the file, and
Code:
adb push
the
Code:
AP_XXXXX
file to your device. How? Download the Android platform tools to the above hyperlink, then extract it, go to the file and then type: e.g
Code:
adb push [DIRECTORY WHERE YOU EXTRACTED YOUR FIRMWARE FILE]\AP_XXXXXX, [FILL IN THE FILE NAME] /sdcard/
4) Then boot up your device, set it up (minimally), download the magisk from below, (25.1-delta file) then install it. Then from the app, select
Code:
Install Magisk > Patch from File
then select the AP_XXXX file you've extracted from your firmware. Wait, for some minutes, and then see what is the file name.
5) Then pull the file and flash with Odin. (Download below) Use
Code:
adb pull /sdcard/Download/magisk_patched-XXXX [See the magisk log for the file name] C:\Users\[your user]\Downloads\
. Open Odin, select okay, when prompted, select AP, select the magisk_patched-XXXX file you've extracted from your phone, untick auto-reboot, then hit flash.
6) Go to stock recovery, again by pressing Volume Down +Power, then while connected to the PC, press Volume Up + Power then navigate via volume buttons and then press with power button,
Code:
Wipe data/factory Reset
7) Turn off the phone (while connected to the PC) by pressing Volume Down + Power, then when turned off immediately press Volume Up + Volume Down. Go back to Odin, download the TWRP image below, and put it in AP slot and untick auto reboot. Then flash
8) Boot to recovery, by again Volume Down + Power, when turned off, Volume Up + Power, whilst connected to PC. ( See 6.) Now you've booted to TWRP Recovery. Go to
Code:
Advance > Terminal
then type
Code:
multidisabler
twice. (Very important)
9) Then download the GSI ROM you want to flash. Here is a list, then
Code:
adb push
then to your /sdcard/, just as you did with 3. (Optional) Either use MTP or
Code:
adb push
to get into your device physwizz's kernel, and GApps (the guide will be in the second post, yet to find a way how to install it)
10) In the recovery, select
Code:
Install > Install Image > select the GSI ROM's .img file you have, and select System Partition.
(Optional) Then select
Code:
Install Zip
Then install physwizz's kernel.
11) Then, reboot, WAILA! There you have it, your own GSI ROM on your A127F U7 device. Enjoy
Credits: @physwizz, for his recovery and kernel ports. Without his hardwork, it wouldn't even be possible to install GSI for U7
Click to expand...
Click to collapse
How it performs? Does it run smoother than OneUI? & Do you have screenshots?
MaybeFazat said:
Can you try magisk gapps?
Click to expand...
Click to collapse
I haven't tried it yet.
MaybeFazat said:
How it performs? Does it run smoother than OneUI? & Do you have screenshots?
Click to expand...
Click to collapse
It performs well, I haven't done any benchmark to see if it performs better than OneUI, but they are pretty different. Although, it performs pretty well in my opinion, and it boots very quickly (as in, the animation only has to run once and it boots already). Unfortunately, I don't have any screenshots, as I reverted back to stock since I need my Google account and Play Store, but you can try and search for "Lineage OS 19. X Screenshots" on Google and I doubt it will give you any different results.
juliano-oh! said:
I haven't tried it yet.
It performs well, I haven't done any benchmark to see if it performs better than OneUI, but they are pretty different. Although, it performs pretty well in my opinion, and it boots very quickly (as in, the animation only has to run once and it boots already). Unfortunately, I don't have any screenshots, as I reverted back to stock since I need my Google account and Play Store, but you can try and search for "Lineage OS 19. X Screenshots" on Google and I doubt it will give you any different results.
Click to expand...
Click to collapse
So i tried for the second time, with Lineage BgS (not BvS since i need gapps) but its bootlooping again, can you help me?
I can't, I tried that too but I haven't found a way to workaround this, sorry to disappoint. I'm guessing that the image is too big for the system that it won't boot. I only find the BvS to be working, and have not yet tried others, except for BgS, which gave me a bootloop too...
it will work for A127F/DSN?
smj320fn-galaxy said:
it will work for A127F/DSN?
Click to expand...
Click to collapse
Yes, but only for LineageOS vanilla, there's yet to find a way to install GApps. If you can live without GApps you can install this then. https://sourceforge.net/projects/an...20221011-UNOFFICIAL-arm64_bvS.img.xz/download
and if i have one ui 4.1 and u7 brinary i still can install it, and in the downloads it says twrp-a127f-u5 brinary?
smj320fn-galaxy said:
and if i have one ui 4.1 and u7 brinary i still can install it, and in the downloads it says twrp-a127f-u5 brinary?
Click to expand...
Click to collapse
yes, the U5 binary TWRP is compatible with U6 and U7
@MaybeFazat I updated the second post. You may now enjoy LineageOS with Gapps. Please tell me what has happened after you install. Feedback will be appreciated.