Hello,
I bought this unit and almost everything works great... Except that it does not sleep or power when I turn off my car.
HU also does not have power menu in android options (original rom and malasysk rom)
From what I understand from other people, when you turn off your car HU goes to sleep. When you turn on HU wakes up Right?
Any possible solution?
Refer this thread: Cross-compatible MCUs - Latest MCU is HA v2.56 which could be applied to your unit to enable sleep menu. Be sure to thoroughly read the thread, document your factory settings and ensure you have your original MCU before starting.
What version MCU are you running?
My MCU is MTCD_KGL_V2.47_1.
With original MCU 2.36_1 also the unit does not turn off.
Even if I turn off unit in buttons, it looks like it only turn off the screen, because I left car parked 3 day and had no battery when arrive to car. Also after some time if I take out the HU, it is still hot!
mochoandre said:
My MCU is MTCD_KGL_V2.47_1.
With original MCU 2.36_1 also the unit does not turn off.
Even if I turn off unit in buttons, it looks like it only turn off the screen, because I left car parked 3 day and had no battery when arrive to car. Also after some time if I take out the HU, it is still hot!
Click to expand...
Click to collapse
Read above thread, suggest upgrading the firmware - MCU and Android. Your unit will then have sleep menu options.
Hi, thank you all for your support . Today I have unmounted my HU and see that the wires that say something like " disconect if have Can decoder" were connected.
I do not remember to have conected it.
I Disconected this cable and HU goes to sleep if I take out the key. NICE!!
Now I'm waiting to see if car can be parked for some days and do not loose battery. hoping so.
Thank you all again.
Interesting, I have a cable that is disconnected on my unit that goes to the CAN bus and wondered why. My unit does turn off after a while. I have the same thing that "Turning Off" just actually turns the screen off. My battery is fine even if I leave the car for 2-3 days.
Mtcd_kgl mcu: 2.54
https://fs08n1.sendspace.com/dl/a6acd7dd8d0ba2caf3b932efccfa4cd6/59602ad026c1e9ce/erfmtd/dmcu.img
Same problem for me..no turn off only sleep mode, disconneted power cable from canbus and only connect b+ to battery.
It's not the power connector from CanBus. You should have I think 3 wires that comes from canbus with a connector. Disconnect that small connector.
AIautobot said:
https://fs08n1.sendspace.com/dl/a6acd7dd8d0ba2caf3b932efccfa4cd6/59602ad026c1e9ce/erfmtd/dmcu.img
Click to expand...
Click to collapse
hi does it work for rk3188?
megamefta said:
hi does it work for rk3188?
Click to expand...
Click to collapse
I have the same version and my vw have canbus so you dont need that 2 connectors ( no canbus) disconnect that 2 cables . My problem is with vehicle app ..my doors are opened and he show me doors closed . The seller cant tell me . How can i update the rom and my android version? I have 6.0.1 and mcu is MTCD_KGL_V2.47_1
OneMisterios said:
I have the same version and my vw have canbus so you dont need that 2 connectors ( no canbus) disconnect that 2 cables . My problem is with vehicle app ..my doors are opened and he show me doors closed . The seller cant tell me . How can i update the rom and my android version? I have 6.0.1 and mcu is MTCD_KGL_V2.47_1
Click to expand...
Click to collapse
Updated MCU for KGL is 2.54 https://docviewer.yandex.com/view/0...pZnJhbWUiOmZhbHNlLCJ0cyI6MTUwMzgwNTMwMjg5Nn0=
but I have same unit and same MCU as you and door setting works fine just had to swap left/right. I think there is a setting in factory settings to edit the door function.
but I have same unit and same MCU as you and door setting works fine just had to swap left/right. I think there is a setting in factory settings to edit the door function.
I know about factory settings , i try it with normal and swap to ..... and nothing . In my dash work fine but on the radio nothing happend . Just the doors and trunk not working. The other like oil .water... working fine on the radio .
stefcio007 said:
Updated MCU for KGL is 2.54 https://docviewer.yandex.com/view/0...pZnJhbWUiOmZhbHNlLCJ0cyI6MTUwMzgwNTMwMjg5Nn0=
but I have same unit and same MCU as you and door setting works fine just had to swap left/right. I think there is a setting in factory settings to edit the door function.
Click to expand...
Click to collapse
What to you mean swap left/right? With kgl not working and now i use dasaita ha last mcu and android 6 . Much better but the doors are still with that problem.
Hi Everyone,
I'm reaching out because I'm facing a challenge with my android Radio in my car and maybe you guys can help me.
I bought 6 Months ago this product:
Eunavi 2 din Android 7.1 8.1 car DVD player GPS for Toyota Corolla 2007 2008 2009 2010 2011 1024*600 screen 8'' car stereo radio.
Everything was fine until recently where when I'm driving and not using the radio, the radio is going to sleep mode, the screen becomes black and there are still some lights switched on around the power button.
The problem is that once this sleep mode is reached, I have no other ways than to switch off the car to reboot the radio unit to get it back to life.
I tried a lot of things including the reset button, Factory reset, but the issue always the same, once I'm on sleep mode for inactivity, I cannot switch it back on for proper normal use.
Is there anyone that has been facing this in the past and that overcome that issue?
Thanks for your help.
chaps_Dub said:
Hi Everyone,
I'm reaching out because I'm facing a challenge with my android Radio in my car and maybe you guys can help me.
I bought 6 Months ago this product:
Eunavi 2 din Android 7.1 8.1 car DVD player GPS for Toyota Corolla 2007 2008 2009 2010 2011 1024*600 screen 8'' car stereo radio.
Everything was fine until recently where when I'm driving and not using the radio, the radio is going to sleep mode, the screen becomes black and there are still some lights switched on around the power button.
The problem is that once this sleep mode is reached, I have no other ways than to switch off the car to reboot the radio unit to get it back to life.
I tried a lot of things including the reset button, Factory reset, but the issue always the same, once I'm on sleep mode for inactivity, I cannot switch it back on for proper normal use.
Is there anyone that has been facing this in the past and that overcome that issue?
Thanks for your help.
Click to expand...
Click to collapse
Anyone can help me?
Thanks Guys!
I recently tried to update the MCU in my Dasaita PX6 head unit. After the update the unit is entirely unresponsive. I looked at the MCU file after I installed it and realized I installed the MCU from another company, not Dasaita. (I realize I should have cheeked this before but I did not and is why I'm in this situation now. Is there anything I can do to fix it? I tried to enter recovery mode, however, the reset button does not work. The screen remains black and the buttons do not light up like they did before the update when the reset button was pressed. Fuses are in good condition. My exact unit is linked here: https://www.amazon.com/Dasaita-Android-Corolla-2014-2017-Carplay/dp/B07XQJH6V6 .
Runnitech said:
I recently tried to update the MCU in my Dasaita PX6 head unit. After the update the unit is entirely unresponsive. I looked at the MCU file after I installed it and realized I installed the MCU from another company, not Dasaita. (I realize I should have cheeked this before but I did not and is why I'm in this situation now. Is there anything I can do to fix it? I tried to enter recovery mode, however, the reset button does not work. The screen remains black and the buttons do not light up like they did before the update when the reset button was pressed. Fuses are in good condition. My exact unit is linked here: https://www.amazon.com/Dasaita-Android-Corolla-2014-2017-Carplay/dp/B07XQJH6V6
Click to expand...
Click to collapse
hi friend i am in same situation, but difference is that i have white screen and do not know what to do.
anybody can help?
saady002000 said:
hi friend i am in same situation, but difference is that i have white screen and do not know what to do.
anybody can help?
Click to expand...
Click to collapse
Hi guys i am in same situation with same Dasaita max10 px6 unit and have only white screen.
I need help to get back to factory settings or add new rom.
If anybody solved please share in details how.
I have messed up my head unit. I was having battery problems so went into car settings and set power default to OFF now I can not power on the head unit power button does not seem to work
Is it an MTCD type head unit.
yes
ra5ta said:
yes
Click to expand...
Click to collapse
Post MCU version or its not an MTCD
its mtcd_kld_v2.88 i tried to update the mcu to see if that would help but it has made no difference. im currently running hal9 android 8. Its a px5 it was originally and r388 but updated the daughter board to px5 also replaced the Bluetooth md750 board so i could run android 8
Hi everyone! Just got my PX6 MTCE android 11 radio (I think 800x640 or something? Misadvertised as 1080p lol) and I am pleased with it so far.
However it only works when the key is in the ignition... It goes into sleep when the key is removed and the power button does not wake it up. Same case when I turn off the engine, it goes straight into sleep mode unlike my OEM radio which would remain on until I pull my key out.
I spend a bit of time with the radio on when the car is off, so I need it to be able to be used when the key is out/car is off.
Is there any solution to this? I briefly checked factory settings and couldn't find much...Would I need to root it? Or should I try to put a relay in the harness? Surely it is software related? Thanks!
Also, the OEM one could be turned on anytime, regardless if the key was present.
The unit I bought was a drop in replacement which included the harness for my car, if that is important.