Database Info

[Completed] Moto e hanged in infinite boot loop.

Model: Moto e XT1022 (India)
Hi,
Sorry If this is not the right place or right question to ask here, I have done a lot of research and may be my question matches with the siliar questions already asked.BUT definitely my problems seems to be different. Please help me out of this.
I tried unlocking the bootloader successfully with (status code:3 and I am getting bootloader unlocked warning message instead of moto logo)
I tried flashing custom recovery TRPW and CWM but its not going well and I am getting error message
<bootloader> failed to erase partition,
<bootloader> failed to erase recovery partition
FAILED (remote failure)
my device ID is getting listed using "fastboot devices" but NOT using adb commands "adb devices"
Earlier I had updated my moto e kitkat 4.4.4 to lollipop 5.0.2 and I was facing lag issue and one day it went to infinite bootloop.
Now I am unable to flash any of the partition using below commands
ALL the commands below are giving error as "Unable to erase Partition......"
mfastboot oem lock begin
mfastboot flash partition gpt.bin
mfastboot flash motoboot motoboot.img
mfastboot flash logo logo.bin
mfastboot flash boot boot.img
mfastboot flash recovery recovery.img
mfastboot flash system system.img_sparsechunk.0
mfastboot flash system system.img_sparsechunk.1
mfastboot flash system system.img_sparsechunk.2
mfastboot flash modem NON-HLOS.bin
mfastboot erase modemst1
mfastboot erase modemst2
mfastboot flash fsg fsg.mbn
mfastboot erase cache
mfastboot erase userdata
Any help would be greatly appreciated.
Thanks in advance

Hi, thank you for using XDA Assist. The best palce to ask your question is here, http://forum.xda-developers.com/moto-e/help
Don't forget to register on XDA to post questions in the forum.

Thread closed.

motorola moto g lte lollipop problem

Mobile after the update to lollipop, will no longer work can not be connected to the network (O2 Germany) when I type * # 06 # - IMEI 0 .. What is?

Download XT1039 Retail Germany Radio Firmware from here: http://forum.xda-developers.com/moto-g/4g-development/rom-stock-motorola-4g-lollipop-rom-t3142816
Use only the following fastboot commands:
mfastboot flash modem NON-HLOS.bin
mfastboot erase modemst1
mfastboot erase modemst2
mfastboot flash fsg fsg.mbn​
Report back how it goes.

Is this still the recommended fix for GPS ?

Using cm13 .most recent nightly ?? Sorry I put this in the wrong forum
Just flash NON-HLOS.bin file of Stock ROM and GPS will be active on any Custom AOSP ROMs.
Code:
mfastboot.exe flash modem NON-HLOS.bin
mfastboot.exe erase modemst1
mfastboot.exe erase modemst2
pause
mfastboot.exe reboot

i fixed it by typing these commands
only without m (fastboot.exe erase modemst1 etc...)

You should just erase modemst1 and modemst2, as described here. Remember that this works for Moto G only and shouldn't be used on other phones!

For the latest CM 13 builds these commands are no longer necessary

Messaging not working on XT1033

Messaging (Incoming & Outgoing) both are not working.
Previously I flashed the CM14 Alpha V4 by @Eurofighter_ty
along with 'Networkfix' and 'forcess', it was working fine but after applying V5 everything sucked.
Calls were not working so I decided to switch to Official CM13 for falcon. Now Messaging is not working on my phone. Please someone help me and thanks in advance.

I faced the same thing couple of days back... here is the solution... you have to flash xt1033 modem via mfastboot... link: http://d-h.st/uJCr
if you don't know what is mfastboot than read this carefully http://forum.xda-developers.com/showthread.php?t=2700502
to flash the modem file use these command...
mfastboot.exe flash modem NON-HLOS.bin
mfastboot.exe erase modemst1
mfastboot.exe erase modemst2
mfastboot.exe flash fsg fsg.mbn

tutul2336 said:
I faced the same thing couple of days back... here is the solution... you have to flash xt1033 modem via mfastboot... link: http://d-h.st/uJCr
if you don't know what is mfastboot than read this carefully http://forum.xda-developers.com/showthread.php?t=2700502
to flash the modem file use these command...
mfastboot.exe flash modem NON-HLOS.bin
mfastboot.exe erase modemst1
mfastboot.exe erase modemst2
mfastboot.exe flash fsg fsg.mbn
Click to expand...
Click to collapse
Thanks it worked

Mi A1 modemst1 modemst2 .bin

Hello Community,
Backed up the QCN, working on the IMEI files.
Changed the QCN via HEX, double checked with NV view, and new IMEI is recognized.
Restroed it, however the old IMEI showed up.
Then erased the modemst1, 2 and fsg
of=/dev/block/mmcblk0p14 15 and 17 to be exact; the IMEI is now 0
Trying restore the QCN again, now IMEI s are 0. QCN doesnt seem to go through. Might be missing something.
PS: Would appreciate if anyone can post modemst1 modemst2 .img and fsg.mbn img files to double check and restore
Thanks