[PORT][AUDIO] Samsung Audio Engine - Android Apps and Games

Short description:
The combined port of the audio engine of Samsung Galaxy S8 and Galaxy S9
The global influence on the sound device, whether it be the sound from the browser, polyphony, microphone recording and audio player
Increases the detail, clarity, volume and selection of instruments in the track being played.
Treated vocals become more lively, deep and saturated low frequencies.
With a long listening to music does not occur discomfort in the ears.
Loss quality audio fixes.
The ability to control proprietary SoundAlive audio effects such as:
- Clarity
- Bass Treble
- Vocal Instrumental
- Concert Hall
- Tube Amp Pro
- Sorround
- 9 band EQ with presets configured
- UHQ Upscaler
- Rehampler UHQ
- Dolby Atmos
Features:
- HiRes effects are ported and used, (list above), ie when listening to music 32/384 or 24/192 and so on, the processing will take place at the same bit rate and frequency
- Dolby Atmos has full support for androids 9.0 and below
Smart installer:
- Support installation via Magisk and determining whether it is embedded in the system
- Support installation directly in the system without disconnecting the device through the terminal emulator, if recovery is not available
- Automatic creation of backup, all replaceable and editable files
- Automatic selection of installation on 32 and 64 bit systems
- Fully deleted, the installer is also an uninstaller, to delete, you must reinstall the archive in the recovery or magic, then the removal process will go
Settings soundalive:
You don’t need the presence of root for the engine, but it is needed to manage its settings.
Settings are stored in /system/etc/soundalive/SoundAlive_Settings.xml
If this file does not appear, flash SoundAlive again.
To apply the settings you will need to restart or restart the interface, which is much faster
Enter the following commands in the terminal:
su
am restart
Effects designed for individual outputs speaker, bluetooth, headphones.
BT__ - Bluetooth Headset
SPK__ - phone speaker
EAR__ - headphones
1 enabled, 0 disabled
Example:
<int name = "BT__SA_GLOBAL_EFFECT_SURROUND" value = "0" /> Effect disabled
<int name = "BT__SA_GLOBAL_EFFECT_SURROUND" value = "1" /> Effect enabled
INSTRUMENTAL_VOCAL
Instrumental Vocal Regulator
Values ​​from -8 to 8, where 0 is disabled, to -8 more instrumental part is allocated, up to 8 vocals are allocated
BASS_TRABLE
Low and high frequency control
Values ​​from -8 to 8, where 0 is disabled, -8 bass is allocated, up to 8 high frequencies
EQ
Presets for 9 band EQ:
0 - Normal
1 - Pop
2 - Classic
3 - Jazz
4 - Rock
5 - Customizable (manual equalizer adjustment is available on this preset only)
SA_SQUARE_INDEX
Clarity
Makes the sound more lively and clear.
Values ​​36, 38, 40, 42
SA_GLOBAL_EFFECT_DOLBY
SA_GLOBAL_EFFECT_DOLBY_OLD
Dolby atmos
A playback system that provides incredibly surround sound and surround sound effect.
To activate the effect, you need to enable, for example, preset music.
DOLBY value = "3"
DOLBY_OLD value = "3"
To disable everywhere put 0
0 - disabled
1 - auto
2 - movies
3 - music
4 - voice
SA_GLOBAL_EFFECT_SURROUND
Sorround
Create a rich surround sound effect.
0 - disabled
1 - enabled
SA_GLOBAL_EFFECT_TUBE_AMP
Tube amp pro
Emulate the tone of a tube amp.
0 - disabled
1 - enabled
SA_GLOBAL_EFFECT_CONCERT_HALL
Concert hall
Sound effect in the concert hall.
0 - disabled
1 - enabled
SA_GLOBAL_EFFECT_UHQ
SA_GLOBAL_EFFECT_UHQ_OLD
UHQ Upscaler
Improve sound quality when playing music and videos for the best listening experience.
To enable, put 1 on both versions
UHQ value = "1"
UHQ_OLD value = "1"
0 - disabled
1 - enabled
SA_GLOBAL_EFFECT_PBM_UHQ_OLD
UHQ Re-sampler
For BT:
0 - off
1 - 96 KHz
For EAR:
0 - disabled
1 - 192 KHz
2 - 384 KHz
SA_LIST_INDEX
3D processing, 5 presets, each has its own sound
0 - disabled
1-5 included
SA_EQ_INDEX_0, frequency 63
SA_EQ_INDEX_1, frequency 125
SA_EQ_INDEX_2, frequency 250
SA_EQ_INDEX_3, frequency 500
SA_EQ_INDEX_4, frequency 1k
SA_EQ_INDEX_5, frequency 2k
SA_EQ_INDEX_6, frequency 4k
SA_EQ_INDEX_7, frequency 8k
SA_EQ_INDEX_8, frequency 16k
9 band equalizer
Values ​​from -10 to 10, where 0 is disabled, down to -10 lowers the amplitude of frequencies, increases to 10 to 10
Important for samsung phones:
Incompatible with official firmware and ports based on them
The list of supported firmware is possible and not all of them will work:
Lineage os
RR
Aosp
And all based on los and do not write about other ports (custom)!
Click to expand...
Click to collapse
Version 4.4:
- Updated installer for the new Magisk
- Updated audio engine
- Updated Sound Alive
- Alsa configuration port, qcom and exynos only
- Connected soundalive via alsa, only for qcom and exynos
- Setting up the audio engine based on the latest Galaxy S9 firmware using a disassembler
- Redesigned general sound panorama
- Added interface in the terminal emulator, for managing effects, in the test
Called by the command: sae
- Added automatic cleaning of the dalvik-cache and reboot
Changed the installation procedure for version 4.4:
1. After installing the engine, the dalvik cache will be automatically cleaned, then the phone should reboot, it will be necessary to wait ...
2. Set SA_Settings
3. Reboot
And enjoy the music
Uninstall:
Run the installer in recovery and the removal process will go
Android required: 5.0+
Recommended Android version: 7.0-9.0
Interface: No
System: 32/64/x86
Stable version: 4.4
Samsung Audio Engine V4.4: Download
SA Settings R8: Download
XDA:DevDB Information
[PORT][AUDIO] Samsung Audio Engine, App for all devices (see above for details)
Contributors
Roman_city
Version Information
Status: Stable
Current Stable Version: 4.3.1
Stable Release Date: 2020-01-09
Created 2019-02-25
Last Updated 2020-02-02

Reserved
Changelog:
Version: 4.2 | 10.05.2019
- Added Magisk support
- Added Speex from S9 improves speech processing
- Fixed bug with hanging outgoing and incoming calls
- Fixed bootloop on mtk android 8.1
- Fixed errors in the engine
- Fixed bugs in UHQ resampler
- Cut conflict files
- Adjustment in sound
Version: 4.1 | 25.02.2019
- Fixed bugs
- Added and corrected system file permissions
- Rewritten installation process
- High resolution effects for androids 5-6 included
- Fixed partition mounting
- Fixed installation process via terminal
- Added option resampler UHQ Upscaler
Version: 4.0 | 03.02.2019
- Updated SoundAlive52 to version 54 from Galaxy S9 9.0
- Added support for high resolution effects.
- Included high-resolution effects, ported from Galaxy S9 9.0 for Android 7.0-9.0, for Android 5.0-6.0 the standard resolution is used
- Fixed Dolby, UHQ effects
- Added choice of quality UHQ Upscaler
Resampler UHQ support:
Bluetooth:
Normal 44.1 kHz
UHQ 96 kHz
Headphones:
Normal 48 kHz
UHQ 192 kHz
SUHQ 384 kHz
- Security update for the engine
- Combined Galaxy s8 engine with Galaxy s9
- Added support for audio pro, low latency if system supports
- Updated pro audio driver
- Removed installation of Google media effects on systems without gapps - this has a good effect on sound
- Improved compatibility with android 5.0-6.0, 9.0
- Updated soundalive settings
- Fixed installer errors
Version: 3.0 | 12.01.2019
- Bugs fixed
- Improved compatibility with android 9.0
- Migrated sound
Version: 2.2 | 31.12.2018
- Updated DolbyAtmos from the latest Galaxy S9 update android 9.0 Pie
- Effects fixes
- Minor installer changes
- Balanced sound
Version: 2.1 | 24.12.2018
- Fixed bootloop on android 9.0 Pie
Version: 2.0 | 23.12.2018
- Fully updated engine from the latest version of the firmware Galaxy S8
- Ported SoundAlive from Galaxy S9
- Ported DolbyAtmos from Galaxy S9
- Added the ability to manage SoundAlive settings and effects such as:
Dolby Atmos
Concert Hall
Tube Amp Pro
Sorround
UHQ Upscaler
3D
EQ
- Fixed compatibility issues with some devices.
- The function that from long listening to music does not cause discomfort in the ears
Version: 1.0 | 28.11.2018
- Ported audio engine from Samsung Galaxy S8
Click to expand...
Click to collapse
Click to expand...
Click to collapse

Interesting, got to try it.
Thanks Dev.

Nice! Thanks for that, now about the Mod
The App force close, is that normal? Are we supposed to edit the settings in the System Files?
Edit: Yes

Is there any apps SoundAlive? Cause I don't see it, but SoundAlive.xml is there.
For sure, my existing Dolby atmos crash.

teatea said:
Is there any apps SoundAlive? Cause I don't see it, but SoundAlive.xml is there.
For sure, my existing Dolby atmos crash.
Click to expand...
Click to collapse
Yes there is, it just does not show up on the Drawer, but you can see it on your Apps List

Guilhermex12 said:
Yes there is, it just does not show up on the Drawer, but you can see it on your Apps List
Click to expand...
Click to collapse
Well, somehow I can't open it. I try to use Sony Music - Setting - Sound Effect, doesn't show.
And most importantly, my Dolby atmos crash.

teatea said:
Well, somehow I can't open it. I try to use Sony Music - Setting - Sound Effect, doesn't show.
And most importantly, my Dolby atmos crash.
Click to expand...
Click to collapse
You actually can't use the app, at least for now, you must edit the settings via the Soundalive.xml file.
And what Dolby Atmos are you talking about? Are you on Oreo?

Guilhermex12 said:
You actually can't use the app, at least for now, you must edit the settings via the Soundalive.xml file.
And what Dolby Atmos are you talking about? Are you on Oreo?
Click to expand...
Click to collapse
I'm on Nougat. On my oreo and pie devices, atmos doesn't work. I keep my Nougat devices only for atmos.

No chance to install on official samsung j7 nougat rom ?

teatea said:
I'm on Nougat. On my oreo and pie devices, atmos doesn't work. I keep my Nougat devices only for atmos.
Click to expand...
Click to collapse
Ah, got it

The sound really got better.
But bootlup on the latest version. Previous worked.
Sharp aquos p1 device
OS: Android 6.0.1
Logcat can be provided if needed

This is an amazing mod. Using 4.2 on one plus 7 pro Android 10. The thread looks dead. I stumbled across it in Google search. Instructions need to be a bit clearer. It also won't install unless you install the sound alive APK. I chose the version closest to the date of 4.2 It really is night and day difference. Much better than the usual distorted sound of viper (for me). Using with digital plus. Sounds stronger than Atmos. Thanks.

Hello everyone, I didn’t go to this resource for a long time, as soon as free appeared, I solved many problems
Version 4.3.1:
- Fixed bootlap on android 9 and 8
- Fixed installation freezing
- Fixed installation failure due to Busybox in recovery and terminal
- Added automatic recovery in case of failure, if changes were made
- Optimized installer
- Optimized and tuned audio engine from captured Galaxy S9 dumps
- Edited SoundAlive settings
Added option to restore audio to a bt headset, a number of options have been removed and changed
https://forum.xda-developers.com/android/apps-games/audio-engine-samsung-galaxy-s8s9-t3904527

Rumin133 said:
The sound really got better.
But bootlup on the latest version. Previous worked.
Sharp aquos p1 device
OS: Android 6.0.1
Logcat can be provided if needed
Click to expand...
Click to collapse
Hello try the new version.

Roman_city said:
Hello everyone, I didn’t go to this resource for a long time, as soon as free appeared, I solved many problems
Version 4.3.1:
- Fixed bootlap on android 9 and 8
- Fixed installation freezing
- Fixed installation failure due to Busybox in recovery and terminal
- Added automatic recovery in case of failure, if changes were made
- Optimized installer
- Optimized and tuned audio engine from captured Galaxy S9 dumps
- Edited SoundAlive settings
Added option to restore audio to a bt headset, a number of options have been removed and changed
https://forum.xda-developers.com/android/apps-games/audio-engine-samsung-galaxy-s8s9-t3904527
Click to expand...
Click to collapse
Many thanks. Big fan. ?
Edit: removed 4.2 and installed 4.3.1. Much clearer sound. OnePlus 7 pro Android pie. Using together with ice sound profile 1 and Dolby digital from repeye. Sound is truly amazing. Thanks again.

tropical cactus said:
Many thanks. Big fan.
Edit: removed 4.2 and installed 4.3.1. Much clearer sound. OnePlus 7 pro Android pie. Using together with ice sound profile 1 and Dolby digital from repeye. Sound is truly amazing. Thanks again.
Click to expand...
Click to collapse
I'm glad you liked it)

Roman_city said:
I'm glad you liked it)
Click to expand...
Click to collapse
Please continue your great work. Hopefully, you could get it to work on Android 10 and more people will try it.

Thanks for this topic and very useful info...

Version 4.4:
- Updated installer for the new Magisk
- Updated audio engine
- Updated Sound Alive
- Alsa configuration port, qcom and exynos only
- Connected soundalive via alsa, only for qcom and exynos
- Setting up the audio engine based on the latest Galaxy S9 firmware using a disassembler
- Redesigned general sound panorama
- Added interface in the terminal emulator, for managing effects, in the test
Called by the command: sae
- Added automatic cleaning of the dalvik-cache and reboot
Samsung Audio Engine

Related

[MOD SOUND] ViPER4Android FX & XHiFi ANDROID 2.3/4.0/4.1/4.2 (GB & ICS & JB)

[MOD SOUND] ViPER4Android FX & XHiFi ANDROID 2.3/4.0/4.1/4.2 (GB & ICS & JB)
ViPER4Android
FX 2.2.0.7 & XHiFi 2.1.0.0
2.3/4.0/4.1/4.2 (GB & ICS & JB)
Short description:
Equalizer with a variety of effects.
Description:
V4A FX version: Adds a variety of sound effects (visualization of sound).
V4A XHiFi version: Restores sound quality.
V4A FX and XHiFi together: More sound settings, the cat. make the sound quality is much nicer.
Specifications
Codename: (FX version) Beautiful / (XHiFi version) X-Factor
Supported OS: Android 2.3 / 4.0 / 4.1 / 4.2
Supported hardware: ARM (ARM15, Cortex A8/A9 or higher).
FX min. requirements (Convolver off): A8 300MHz or ARM11 500MHz.
FX min. requirements (Convolver included): A8 single-core 800MHz, recommended dual-core or quad-core 1.2GHz.
XHiFi min. requirements (all effects included): A8 dual-core 1GHz or higher, Tegra2 processor supported.
Supported languages​​: English (United States) / Simplified Chinese / Traditional Chinese.
Screenshots
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Download FX-version:View attachment ViPER4Android_FX_2207_en.zip
Download XHiFi-version:View attachment ViPER4Android_XHiFi_2100_en.zip
IRSamples for Convolver:View attachment IRSamples.rar
Recommended settings from the author
ViPER4Android_FX
<Headset>
1. Master Power: ✔
2. Playback Gain Control
(1) Enable checkbox: ✘
(2) Select Effect Strength: Slight
(3) Max Gain: 4x
(4) Max Output: -1.9dB
3. FIR Equalizer
(1) Enable checkbox: ✘
(2) Select Preset: Acoustic
(3) Linear Equalizer graphic: default
4. Convolver
(1) Enable checkbox: ✔
(2) Impulse Response: PopEQ // DBX 160SL Blue - Medium Ratio // JoeMeek SC2 Impulse
5. Field Surround
(1) Enable checkbox: ✘
(2) Select Field Surround Strength: Extreme
(3) Select Mid Image Strength: Extreme
6. Reverberation
(1) Enable checkbox: ✘
(2) Room Size: 25m2
(3) Sound Field: 5m
(4) Damping Factor: 0 Percent
(5) Wet Signal: 0 Percent
(6) Dry Signal: 50 Percent
7. Dynamic System
(1) Enable checkbox: ✘
(2) Select Listening Device: Common Earphone(v2)
(3) Select Dynamic Bass: 0 Percent
(4) Tube Simulator(6N1J): ✘
8. Master Gate(Limiter)
(1) Ouput Gain: 0dB
(2) Limit Threshold: 0dB
<Phone Speaker>
1. Master Power: ✔
2. FIR Equalizer
(1) Enable checkbox: ✘
(2) Select Preset: Acoustic
(3) Linear Equalizer graphic: default
3. Convolver
(1) Enable checkbox: ✔
(2) Impulse Response: Studer +1dB Updated
4. Reverberation
(1) Enable checkbox: ✘
(2) Room Size: 25m2
(3) Sound Field: 5m
(4) Damping Factor: 0 Percent
(5) Wet Signal: 0 Percent
(6) Dry Signal: 50 Percent
5. Extra Loud
(1) Enable checkbox: ✘
(2) Select Effect Strength: Slight
(3) Max Gain: 4x
(4) Max Output: 0dB
6. Master Gate(Limiter)
(1) Ouput Gain: 0dB
(2) Limit Threshold: 0dB
ViPER4Android_XHiFi
1. Master Power: ✔
2. Playback Gain Control
(1) Enable checkbox: ✔
(2) Select Effect Strength: Slight
(3) Max Gain: 4x
(4) Max Output: -1.9dB
3. FIR Equalizer
(1) Enable checkbox: ✔
(2) Select Preset: Acoustic
(3) Linear Equalizer graphic: default
4. Audio Reconstruction
(1) Enable checkbox: ✔
(2) Hi Clarity: 50
(3) Lo Contour: 70
5. Master Gate(Limiter)
(1) Limit Threshold: 0dB
installation
1) Download and unzip the IRSamples.rar the root of the SD-card (SD-card\Viper4Android\Kernel\*.irc)
2) Set the selected ank (FX or XHiFi) of acc. file - can be both, because they get along well together
3) apk run and follow the instructions appearing on the screen
And for other system Poweramp music players (e.g., MIUI music player, Apollo, etc.
From version: FX v2204, XHiFi v2007:
To make it work with V4A Poweramp correctly, you have to both applications (FX and XHiFi), switch to Compatible Mode and then reboot the phone.
CODEC CHOOSE WHAT?
NEW! Starting with version FX 2207:
ZTE U880 or same CPU (PXA920), choose - "PXA920 without VFP" (Convolver disabled)
Tegra2 or any CPU with freq equal / less than 800MHz, choose - "ARM with VPF"
Qualcomm of freq higher than 800MHz - single core, choose - "A8 with NEON"
ALL other Dual-core, Quad-core, Octa-core, choose - "A9/15 with NEON"
NEW! Starting with version: XHIFI 2100
Tegra2, choose - "NVIDIA Tegra2"
ALL others, choose - "CortexAx with NEON"
Homepage: Original theme author on XDA <-> Original theme author's Chinese website
IRS samples for convoluters (convolver)
IRS samples for convoluters (convolver) thanks tranceman111
So what is the convolver (Convolver), and what it eats? try to understand
Start by asking the concept - "Reverb"
"Reverb - a reflection of sound from the different items that surround it (walls, floor, ceiling, windows, bookshelves, trees, houses and even people.) Any sound that we hear in life, is not a pure signal, and contains themselves more and their reflections on the various surfaces. "
Convolution reverb or just convolver
It is also called convolution reverb and pulse. It uses impulse responses of the various processing facilities or equipment (other reverbs), repeats the distribution of fluctuations in the original.
More information can be read: here and here
IRS (Impulse Response) - is an impulse response in the form of short Wave files that are loaded into convoluter, through which he recreates a mathematical model of a room, reverb, devices, etc. from which recorded (shot) pulse! (ie the impulse response contains a linear response of your system (ie frequency response), and does not include the non-linear characteristics (ie distortion / color).
PULSES
Technics Vintage IRS
[Pulses with vintage equipment Technics (1978 issue) preamp and power amp.
Technics+Vintage+v4
Presets+Technics+Equ
Version for those who do not pull the processor (wheezing, stuttering, delay, etc.)
Technics+SU-9011(Preamlifier)+&+SU-9021(PowerAmplifier)+LITE+IRS
Presets+Technics+Equ+Lite
SuperLight Technics Vintage v4
SuperLight Preset Technics Equ
later
WORK Beats Audio, SRS, Dolby mobile, xLOUD + ViPER4Android FX & XHiFi
To work sound effects Beats should be laid out in this thread I've found (system / etc / audio_effect.tsonf) before installation and after installation. I made ​​the necessary Changes to your firmware.
audio_effect.conf to put the replacement in
/ system / etc / audio_effect.conf
Restart the phone.
Full work
[ROM][Sense 4.1][20.01] Team Venom presents: ViperS 1.6.3 - welcome to the future.
View attachment audio_effects.rar
FAQ Reserv
Q: What makes this program?
A: This program is a conventional equalizer with a wide list of options, working with almost all the players.
Q: How do I install?
A: Set yourself ank, run and follow the instructions poyavivscheysya. If the default setting does not help, use FLASHABLE-version.
Q: Why the program needs ROOT?
A: Then, what driver (library) that are required to operate the program prescribed (set) in the section: system / lib /
Q: What kind of CPU to choose for my device?
A: Table of compliance processors, see the cap under the spoiler.
Q: Where to copy files (samples) for Convolver'a?
About: SDCard/ViPER4Android/Kernel / - Case of letters dlozhen be strictly adhered to!
Q: I downloaded a new impetus to the device for the convolver, and the device does not see them, why?
A: Advice to all who do not work convoluter, make sure that the files pulses *. Irs you have piled up in a heap in the folder ViPER4Android/Kernel rather than sorting into folders.
Q: What is the format (extension) to be in the sample?
A: Since version 2.2.0.3 (2.0.0.6) and further, the file extension "Nonlinear processing" (aka Convolver) with. Wav replaced by. Irs
Q: How to make the new drivers? After all, there is laid only apk.
A: Install the program and open it, it will offer to update the driver.
Q: How do I use different pulses are then laid out? I put a version XHiFi, but there is no any choice of these same effects ...
A: The pulses are designed to convoluter (convolver), cat. there is only a version of the FX! At the root of the memory card create a folder: / ViPER4Android/Kernel / and there throws impulses. Now, where in the program choose the right impetus.
Q: I have a program does not work with PowerAmp'om. What to do?
A: To get to work with V4A Poweramp correctly, you have to both applications (FX and XHiFi), switch to Compatible Mode and then reboot the phone.
In: Switch from Normal to Compatible and still with PowerAmp does not want to. Maybe something else to turn on or off in PowerAmp? Prompt?
A: PowerAmp need to go to Settings-> Sound-> Advanced Settings-> put a checkbox on musicfx. Then tab tone / volume set compulsory treatment by activating point musicfx (in this case in the system settings must be activated V4A), long press on musicfx otkryvaetsya equalizer that are currently using the system.
Q: When installed a program, and tried to find the driver Toli Toli update I wrote this: "please comfirm your phone has been rooted and busybox installed". What do I do?
A: First, the program will necessarily need ROOT-law, and secondly, we must also install Busy Box. It select the smart installer and reboot.
Q: What's the difference between versions XHiFi?
About: V4A XHiFi version is mainly to restore the sound quality and detail. This is the main feature of XHiFi, making detailed and high frequencies to restore losses to MP3 audio files.
In install the latest version of V4A through AIC. Install both the equalizer. On the second why you do not have the settings for the speaker. This is as it should be or cant install?
About: XHiFi intended only for the headset (headphones) / BT, but if you want to use XHiFi for the speaker, then simply activate the lock effect mode in XHiFi application.
Q: Can I use them both at the same time or just individually?
A: You can either - they get along well together and complement each other perfectly.
Q: I installed both versions, but activate only one of them, and in the process both hang. Why is that?
A: It does not matter which version you have activated - FX or XHiFi, they will still always be run together (provided that they are installed both).
Q: If fx is the driver, should be put hifi, whether or not the driver put it?
A: Yes, on the first run, the program will prompt you to update draver.
Q: There are significant differences from the DSP Manager is available?
About: V4Android partly based on the source code of the DSP Manager, that is, in fact, it is more advanced (improved) version of it.
Q: And now all in one file? Previously, there was also a manager. Explain.
A: Since version 2.2.0.4 (2.0.0.7) and further, manual installation is now - will not be as program itself will update the driver at startup.
Q: Unpacked impulses for convoluters, but the application of sound stutters. Tell me what's the problem?
A: The processor is unable to cope. Disconnect convoluter.
Q: How to use this non-linear processing? Which of this heap of files in the format. Irs stand for improvement?
A: Anyone, what you enjoy. They are all in their own way alter the sound, so only you can choose what you like.
Q: Can me more about the actual samples? Everything can be put right? And at some specified phone model, what is it?
A: Yes, you can throw all the samples in a single folder. If on a sample contains the model number, so this phone has some kind of his trademark uluchshayzer (such BeatsAudio from HTC), while the use of which was filmed sample (using the spec. Equipment).
Q: What is the mode of Safe Mode (Safe Mode), and what is it for?
A: If you V4A not work with any player, then try switching to Safe Mode, cat. and is designed to work with almost any music player with a cat. V4A does not work in Normal Mode (works only with the Android 4.X and above).
Q: What is the mode Compatible Mode (compatibility mode) and what is it for?
About: Compatible Mode supports a larger number of both system and third-party music players and players with their own sound effects or EQ (works only with the Android 4.X and above).
In: Switch to Compatible Mode, and I wrote that the Driver status: NO
About: Driver status in V4A FX Compatible Mode will always show - NO. YES will show only in Normal Mode - this is a bug of the program.
In: Switch to Compatible Mode, reboot, but nothing changed ... (Option 1)
A: If you want to use Compatible Mode, then you need to switch to this mode, both applications (ie, both XHiFi and FX).
In: Switch to Compatible Mode, reboot, but nothing changed ... (Option 2)
A: For those who still remained a problem with effects in Compatible Mode, even after a reboot, do the following: Locate the file - / system / build.prop and change the line with: Ipa.decode = true on lpa.decode = false
Q: Why ViPER4Android FX always leads to FC when headphones?
A: Most likely you have not write to the partition / system / on the device, so the drivers were not installed. Allow entry to the system partition and reconfigure the automatic installation of drivers or install them manually.
Q: Why ViPER4Android FX creates unexpected sound effects, cat. not observed (or different) from other users?
A: First, try to clean the data ViPER4Android FX, and if that is unsuccessful, then make sure you do not stand the sound of the amplifier.
Q: Why ViPER4Android FX will not boot after boot device?
A: Check your antivirus, or else V4A was off the list of startup.
Q: Why do missing V4A effect after using task-killer'a?
A: Just add ViPER4Android FX to the list of excluded task-killer'a.
Q: Why V4A effect suddenly disappears?
A: Because the Android system kills some processes due to memory limitations. Just set ViPER4Android.apk as system application (move it to / system / data / and reboot the device.)
Q: Why there is background noise when using v4a effects?
A: This error Android, cat. they will all sound modes (BeatsAudio, etc). Try to rename the file: / system / lib / SoundFX / libbundlewrapper.so in libbundlewrapper.so.bak, and reboot the device.
Q: I'm trying to install the program, wrote that the driver is not installed. Check for root and biziboks. Both are found in the catch, I do not understand ...
A: Perhaps you should not permit entry in the system, so the driver and did not put. Try to install the drivers manually for this instruction.
Q: Tell me, in the status of the driver, the value of treatment - no, it's that it does not work or does not work?
A: Status: Processing - NO (if the music is not playing); Processing - YES (if the music is playing).
Q: What is the Cure +?
A: When listening to music, with a normal audio system for more than three hours, you'll start to feel fatigue, dizziness, tinnitus, irritation and other ailments. This is a normal reaction of the body, as heavy bass and loud sound can cause permanent damage to the human auditory system. But from these symptoms can easily get rid of - just enough, just relax a bit. Viper is also the professional tool for listening to music, so we decided not to ignore the problem. We put a lot of effort to develop a more "innocent" technology listening to music, and have achieved little success. But think about how to give users the opportunity to experience it. It is this "little success" and is a technology - Cure +. But we are still working on how to better present this technology to the user.
Which music player that you recommended except Power AMP?
baronzelan said:
To work sound effects Beats should be laid out in this thread I've found (system / etc / audio_effect.tsonf) before installation and after installation. I made ​​the necessary Changes to your firmware.
audio_effect.conf to put the replacement in
/ system / etc / audio_effect.conf
Restart the phone.
Full work
[ROM][Sense 4.1][20.01] Team Venom presents: ViperS 1.6.3 - welcome to the future.
View attachment 1978979
Click to expand...
Click to collapse
thanks should i change permission after replacement in
/ system / etc / audio_effect.conf
Rvl7 said:
Which music player that you recommended except Power AMP?
Click to expand...
Click to collapse
I use HTC music player. You can use any player, only need to turn on in the settings ViPER4Android:
And for other system Poweramp music players (e.g., MIUI music player, Apollo, etc.
To make it work with V4A Poweramp correctly, you have to both applications (FX and XHiFi), switch to Compatible Mode and then reboot the phone.
mamdouhn said:
thanks should i change permission after replacement in
/ system / etc / audio_effect.conf
Click to expand...
Click to collapse
Yes
- Go to: / system / lib / soundfx / a RootExplorer
- Make this folder writable
Come-in: / system / etc / a RootExplorer
- Make this folder writable
- Manually put the file there - audio_effects.conf (from the archive below)
- Reboot the device.
baronzelan said:
Yes
- Go to: / system / lib / soundfx / a RootExplorer
- Make this folder writable
Come-in: / system / etc / a RootExplorer
- Make this folder writable
- Manually put the file there - audio_effects.conf (from the archive below)
- Reboot the device.
Click to expand...
Click to collapse
thanks
so / system / lib / soundfx will be rwxr-xr-x
and audio_effects.conf will be rw-r--r--
is it right ?
thx
Very nice thank you
This Mod works perfectly with ViperS 1.6.3 within Htc Music Player (better than any other mod). And please refer to @zhuhang original thread for latest updates.
is there any iinterference with Beats, or it works along with Beats?
DarkLP said:
is there any iinterference with Beats, or it works along with Beats?
Click to expand...
Click to collapse
Works with Beats
Pretty nice....thanks.
"I wanna be the apex of predators in my backyard"
Joe Rogan
Thanks, one question do we need to create folder on sd card ? to copy IRsample.rar there? I cant see any folder created by application after running it. can some one provide exact path with exact name of folders if we need to create manually.
Also how to use these IRsample?
Sent from my Micromax A116 using Tapatalk 2
Works perfect with vipers 3.0.2 along with beats audio. It's amazing, thanks
can i use this on xperia device?
khamim said:
can i use this on xperia device?
Click to expand...
Click to collapse
Yes but goto original thread for more info and latest version. Link in OP and in my Sig.
Sent from my HTC Sensation
How can I make this work on viper jb rom?
Sent from my HTC Sensation Z710e using xda app-developers app
Does it works on ViperS 5.1.0 sense 5 ???

[MOD][May 19] ICE CAVE 11.0 [4.2.2-5.0.2]

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
ICE CAVE 11.0
Why such name you might ask?
Nothing special, just an acronym of a modest description for this mod:
Intelligent Concept of Excellence
Complex Audible and Visual Enhancements​
ICE CAVE incorporates different enhancements for your HTC One's media functions.
It uses Xperia software, Dolby Digital and SRS technologies. Using the pack with other similar mods is not recommended, it can cause some unexpected results.
Make a nandroid backup before installing to be able to remove this mod.
Mod was tested mainly with Android Revolution HD ROM, but should work with other Sense ROMs as well. Probably on GPE too, but not on AOSP.
Installation
Just flash ICE CAVE mod from custom recovery of your choice. Follow instructions in toast notifications on first boot after flashing.
Along with the latest Xperia libs you can optionally install following apps:
DSP category
Sony Sound Enhancements (Equalizer, ClearAudio+, ClearBass, Clear Phase, Clear Stereo, xLOUD, S-Force Front Surround, Surround sound (VPT)) and Dolby Digital Plus
Without DSP (select this if you are using any other 3rd party DSP)
If you want to use Sony Sound Enhancements or Dolby Digital Plus as your DSP, select Ice Control module installation option during flashing. It also requires Xposed Framework to work.
Audio category
Walkman 9.1.4.A.0.3 with plugins
It is highly recommended to use Walkman together with Sony Sound Enhancements!
Graphics category
Album 7.4.A.1.22 with Photo Editor 5.0.A.0.16
Video 9.4.A.1.6
Podcast 2.1.A.0.12
Motiongraph 1.0.9
DLNA category
Devices 8.1.0.A.0.12 (adds DLNA capabilities to Walkman, Album and Video apps).
Changelog
11.0
- Frameworks, libraries and Sony Sound Enhancement were updated from Xperia Z5 Premium 5.1.1
- Added Experience Flow (Xperia live wallpaper)
- Music updated to 9.1.4.A.0.3
- Album updated to 7.4.A.1.22
- Photo Editor updated to 5.0.A.0.16
- Video updated to 9.4.A.1.6
- Podcast updated to 2.1.A.0.12
- Devices (DLNA) updated to 8.1.0.A.0.12
10.2
- Sense 7 ROMs support (full ports)
- Album updated to 7.2.A.0.18
- Music updated to 9.0.1.A.0.1
- Video updated to 9.2.A.0.6
10.1
- Enabled Sony SE effects: Clear Phase, Clear Stereo and xLOUD
- Video updated to 9.1.A.0.8
- Album updated to 7.2.A.0.8
- Photo Editor updated to 5.0.A.0.12
- Fixed Ice Control FC (still not compatible with Sense 7)
- New Xperia-styled icon for Ice Control app
10.0
- Brand new Sony Sound Enhancements with Material design, working S-Force Front Surround and Headphone selection
- Option in Walkman to edit track info (downloading from network is not working)
- Option in Ice Control to restore Walkman app name and icon
- Fixed Dolby crash
- Dual Dolby Digital Plus option (from Lenovo Tab S8 and Huawei Ascend P7)
- Music (Walkman) updated to 9.0.0.A.0.1
- Walkman Music Visualizer fixed and updated to 2.3.A.0.7
- Album updated to 7.1.A.0.22
- Photo Editor updated to 3.1.A.0.48
- DLNA updated to 8.0.0.A.0.8
- Video updated to 9.0.A.0.20
- Podcast updated to 1.1.A.1.8
- Updated services, frameworks and libs from Xperia Z3 5.0.2
- Support for Android 4.4 was dropped
8.1
- Walkman updated to 8.5.A.3.2
- Album updated to 7.0.A.0.24
8.0
- Android 5.0 compatibility
- Movies updated to 8.0.A.0.8
- Walkman updated to 8.5.A.2.10
7.1
- Walkman updated to 8.5.A.2.8
- Updated audio config and frameworks, mod cleaned up
- Material icons for some Sony apps
- Ice Control russian translation
7.0
- Added Dolby Digital Plus from Huawei Ascend P7 (slightly modified stock presets)
- Album updated to 6.6.A.0.6
- Photo Editor updated to 3.1.A.0.46
- Updated Ice Control app
- Support for Android below 4.4 and Sense below 6 was dropped
6.1
- Sketch app removed (available in Play Store)
- Walkman updated to 8.5.A.0.6
- Ice Control app with Sense 6 styled UI
6.0
- Fixed SRS TruMedia on 4.4.3+
- Walkman updated to 8.4.A.5.4
- Album updated to 6.5.A.0.10
- Movies updated to 8.0.A.0.6
- Movies converted to user app, otherwise video thumbnails are not working
5.9
- Walkman updated to 8.4.A.4.4
- Movies updated to 7.3.A.0.2
- Album updated to 6.3.A.0.12
5.8
- Libs updated from Xperia Z3
- Walkman updated to 8.4.A.3.2
- Walkman Music Visualizer updated to 2.2.A.4.1
- Walkman plugins updated to 5.0.A.0.8
- DLNA updated to 7.0.0.A.0.9
- Movies updated to 7.1.A.1.12
- Podcast updated to 1.1.A.0.26
- Album updated to 6.3.A.0.10
- Photo Editor updated to 3.1.A.0.42
- Sketch updated to 2.0.A.1.6
5.7
- Walkman updated to 8.4.A.1.4
- Album updated to 6.2.A.0.22
5.6
- Movies updated to 7.1.A.0.4
- Sketch updated to 2.0.A.1.1
- Fixed lib conflict for Album by installing it as an user app
5.5
- Walkman updated to 8.3.A.0.7
- Walkman visualizations should work now (at least on latest 4.4.2 ROMs)
- Album updated to 6.1.A.0.14
- Movies updated to 7.0.A.0.8
5.4
- Improved audio config and build.prop entries (enabled audio offloading and some other tweaks)
- Movies updated to 6.2.A.0.10
5.3
- Walkman updated to 8.3.A.0.5
- All frameworks were updated from latest Xperia Z2 firmware
- Option in Ice Control to enable ClearPhase and xLoud (please read warning there first!)
5.2
- Walkman updated to 8.3.A.0.2
- Album updated to 6.0.A.0.26
- New icon and name for audio settings app: Ice Control
- HTC One M8 compatibility (untested)
5.1
- Improved Sense 6 compatibility
- Removing navbar gaps is now an option in Ice Cube module
- Movies updated to 6.2.A.0.8
5.0
- Complete mod rebranding to ICE CAVE
- Ice Cube Xposed module (previously known as Xperia Pack Helper), can now be automatically installed on first boot after mod installation
- Noozxoide EIZO-rewire is no longer an option (you can still install it from Play Store and use with ICE CAVE)
- Devices (DLNA) updated to 6.0.0.A.0.12
- Google Lyrics Plugin updated to 5.0.A.0.6
- Wikipedia Plugin updated to 5.0.A.0.6
- YouTube Karaoke Plugin updated to 5.0.A.0.6
- YouTube Plugin updated to 5.0.A.0.6
- Fixed FC for Google Music Extension
- Improved init.d script
Previous mod incarnation as XperiaPack
4.9
- Experimental SRS TruMedia effects (Xperia Pack Helper is required)
- Walkman updated to 8.1.A.0.7
- Album updated to 5.4.A.0.24
- Movies updated to 6.1.A.0.18
4.8
- Added Podcast 1.1.A.0.6 plugin for Movies app
- Photo Editor updated to 3.1.A.0.34
- DLNA (Devices) updated to 6.0.0.A.0.11
- Sketch updated to 1.0.A.4.5
- Updated libs and frameworks
- Improved build.prop management
4.7
- Walkman updated to 8.1.A.0.6
- Movies updated to 6.1.A.0.16
- Album updated to 5.4.A.0.22
- Sketch updated to 1.0.A.4.2
4.6
- ClearPhase and xLOUD effects are forced to stay disabled to prevent high volume spikes (don't forget to update Xperia Pack Helper to 4.6)
- Fixed Small Apps crash on Viper One ROMs
- Walkman updated to 8.1.A.0.3
- Album updated to 5.4.A.0.20
- Removed unused libs
4.5
- Minor fixes in audio config
- Album updated to 5.3.A.0.24
- Sketch updated to 1.0.A.2.6
- Movies updated to 5.3.A.0.20
- AROMA Installer: new theme and 7z compression to reduce mod size
4.2
- Improved priorities script, it will display a toast when executed
- Minor libs/frameworks update
- Xperia Pack Helper 4.0 with Sony SE per app profiles support
4.1
- Sony Sound Enhancements is a preferred DSP now
- Improved Sony Sound Enhancements priority
- Smoother volume adjustment
- Sketch updated to 1.0.A.2.5
- Added Motiongraph for Xperia 1.0.9
4.0
- Compatibility with all recent android versions, one mod fits all
- Two different DSPs available: Noozxoide and Sony Sound Enhancements
- Walkman updated to 7.15.A.0.2
- Album updated to 5.2.A.1.26
- Movies updated to 5.3.A.0.18
3.2
- Stock HTC Music visualizer is working now!
- Scripts and configs update
3.1
- Album updated to 5.2.A.1.20
- Walkman and Noozxoide are given higher priority to prevent their unloading or restarting
- More options for separate app install
- Couple of frameworks updated
3.0.2
- Fix for reboots on some ROMs (no need to update if you don't have them)
3.0.1
- Removed ability to edit music info in Walkman (consumes a lot of battery due to service compatibility problems)
3.0
- 4.4 Kit Kat compatibility
- Walkman updated to 7.15.A.0.0 (you can remove software keys gap by installing Xperia Pack Helper Xposed module)
- Added ability to edit music info in Walkman
- Redundant files were removed
2.2
- Version for android 4.3 and lower was updated with changes from 3.x branch
2.1.1
- Zipaligned all APKs
- Added and updated some libs
2.1
- Album updated to 5.2.A.0.6, SensMe™ SlideShow and PlayMemories Online added
- PhotoEditor updated to 2.1.A.0.36
- DLNA updated to 6.1.D.0.1
- Sketch 1.0.A.1.11 added to Graphics category
- Minor sound and image quality tweaks
2.0
- Higher speaker volume
- Aroma installer with selection of what apps to install
1.0.1
- Noozxoide updated to 2.0.1.18
Known problems
Sony SE/SRS effects have a delay before they are applied after system start, wait a minute until your device is fully booted.
SenseMe is broken on 4.4+
Ice Cotrol settings will FC on Sense 7​
Download
Current version (5.0 Sense 6 and 7)
ICE CAVE 11.0
Mirror
MD5: 63C4BCC47E687758392EBA3EDE9DC3FC
SHA-1: B93DB2256B01B6BF429A7CF830708DEAC1B9A160
Last version that supports Kit Kat (4.4-5.0 Sense 6)
ICE CAVE 8.1
Mirror
MD5: 2115968A040FC81160E00C18AF4D3135
SHA-1: 21F4BCC1DFF7F05355F023D6C89755AC017E07EA
Last version that supports Jelly Bean (4.3-4.4)
ICE CAVE 6.1
Mirror
MD5: 5F78E735EE71CA91345A7EEAE7A70393
SHA-1: FCAA30D3379B857C4AD5FA5D0C1FFAD0124B3EC9
Last version of the outdated Xperia Pack mod
Xperia Pack 4.9
Mirror
Ice Control
This Xposed module is required for Sony Sound Enhancements, Dolby Digital Plus and SRS TruMedia to work!
Additional functionality:
Sony SE audio effects log (shows what apps use Android's MediaPlayer and have effects applied).
Dolby Digital Plus sound presets
SRS TruMedia sound presets
Remove softkey gaps from Walkman, Album, Video and restore Walkman app name and icon
Hide foreground service notifications for apps in this mod on android 4.3+
Current version (5.0 Sense 6 and 7)
Ice Control 11.0
Module is included in ICE CAVE and can be installed during flashing.
Last version that supports Kit Kat (4.4-5.0 Sense 6)
Ice Control 8.1
Last version that supports Jelly Bean (4.3-4.4)
Ice Cube 6.1 Sense 6 UI
Ice Cube 6.1 Holo UI
Outdated version
Xperia Pack Helper 4.9
XDA:DevDB Information
ICE CAVE, Tool/Utility for the HTC One (m7)
Contributors
Mikanoshi
Version Information
Status: Stable
Current Stable Version: 11.0
Stable Release Date: 2016-02-08
Created 2014-03-12
Last Updated 2016-02-13
FAQ
I keep seeing notifications that Album and Movies were installed
Remove SemcAlbum.apk and SemcVideo.apk manually from /system/etc/
Ice Control and/or Album crashes on boot
Such behavior is expected if it's your first boot after flashing, (soft) reboot again to complete installation.
Maybe a stupid question, but ARHD 31.5 come with pureXaudio 8.0
Is you're mod compatible with that?
9600pro87 said:
Maybe a stupid question, but ARHD 31.5 come with pureXaudio 8.0
Is you're mod compatible with that?
Click to expand...
Click to collapse
Mods replace the same files so they cannot be fully compatible, sound quality will be lower and Noozxoide presets will have less effect if this pack is used together with PureXAudio.
Mikanoshi said:
Mods replace the same files so they cannot be fully compatible, sound quality will be lower and Noozxoide presets will have less effect if this pack is used together with PureXAudio.
Click to expand...
Click to collapse
Good. Tomorrow i flash new rom and then you're mod
Thanks for information!
I am on ARHD 31.5 with PXA. I'd like to test this out so would you recommend I do clean install to leave PXA out or will a dirty install be ok?
Perfect
Just a heads up for anyone with InsertCoin ROM.
Working great on InsertCoin 6.0-5 :good:
Kahbrohn said:
I am on ARHD 31.5 with PXA. I'd like to test this out so would you recommend I do clean install to leave PXA out or will a dirty install be ok?
Click to expand...
Click to collapse
It will be a lot better to dirty reflash ROM without PXA and then install this mod.
Mikanoshi said:
It will be a lot better to dirty reflash ROM without PXA and then install this mod.
Click to expand...
Click to collapse
EXACTLY what I hoped to hear. Thanks and thanks fotr your work/efforts!
Does this walkman has working xloud like the one from 4.2.2 made by Ravi ?
Sent from my HTC One using XDA Premium 4 mobile app
Shan89 said:
Does this walkman has working xloud like the one from 4.2.2 made by Ravi ?
Click to expand...
Click to collapse
Link to that mod please) There is no separate option for xloud like on xperia devices, but xloud engine and libs are there. With this mod sound is reasonably loud in speakers (and deafening in headphones on volume 80%+, at least with my AKG).
Sound enhancements Do work?
Gesendet von meinem HTC One mit Tapatalk
flooi said:
Sound enhancements Do work?
Click to expand...
Click to collapse
DSP is Noozxoide in this mod, not DSP Manager, Sound Enhancer or any other and I didn't test with them.
You can always install and try
MotoXoom said:
Just a heads up for anyone with InsertCoin ROM.
Working great on InsertCoin 6.0-5 :good:
Click to expand...
Click to collapse
Thanks for the info.
Just one question, did you install it over V4A or did you remove V4A before installing this mod?
lee901 said:
Thanks for the info.
Just one question, did you install it over V4A or did you remove V4A before installing this mod?
Click to expand...
Click to collapse
Removed V4A before install!!!
Hi! Installed this mod over Elegancia v21 and it work very good. I love walkman player and album so much. Sound quality is good too. Thank you so muck man!
This is great. Sony media apps really are the best and its great to have them back in Sense 55.
I assume that beats needs to be disabled as well as any third party EQ apps, correct?
Any chance of seeing X-Reality? Is X-Reality actually any noticeable improvement on image quality?
hypocritelecteur said:
I assume that beats needs to be disabled as well as any third party EQ apps, correct?
Any chance of seeing X-Reality? Is X-Reality actually any noticeable improvement on image quality?
Click to expand...
Click to collapse
I use it with Beats on, sound in headphones stays almost the same with it, but with speakers sound it makes wonders.
Don't know what is X-Reality Quick googling shows that it is based on bravia 2 engine with some sharpening and filmgrain effects, I'll see whether it can be ported.
P.S. Checked several Bravia and X-Reality mods for other devices, it seems all files for them are already in Xperia Pack But I didn't compare image quality with stock, the difference should not be that big. Maybe it is already working?)
Without -> Bravia -> X-Reality:
That's actually a lot more pronounced than I expected. Bravia was 99% puff and 1% exaggeration. Barely any difference to my eye. But stock:xreality is quite noticeable.
Any chance of porting Honami keyboard ? You can find it in Auras76 pack which works on 4.2.2 but no one so far i found has honami keyboard on 4.3 , all claim it's Honami keyboard but it's not , it's XZ keyboard lol.
Maybe you could throw some of your magic in it?
Here hes topic http://forum.xda-developers.com/showthread.php?t=2353147
It also had working xLoud in walkman.
It'd be nice if you could port it over to 4.3 since he doesn't care anymore.

[APP][Audio]JamesDSPManager 8 Band Equalizer[ROOT]

JamesDSPManager (Audio Effect Digital Signal Processing library for Android)
This is a REFORMED audio effect for Android. Source code and main app release available on Github:https://github.com/james34602/JamesDSPManager
The GUI is copy from Omnirom DSPManager, but the internal audio engine is enhanced and reformed!
Features:
1. Pro dynamic range compression
2. Bass Boost
--> 2048/4096 order FIR linear phase low shelf bass boost
3. Reverberation (Dual engine reverb)
--> GVerb
--> Progenitor 2
4. 15 bands cubic spline interpolated FIR Equalizer
5. Stereo Widen
6. Triode dual stage vacuum tube simulation
--> Simulate with real mathematical model of 12AX7 tube
6. Auto partitioning high efficient convolution engine
--> Support mono / stereo / full stereo(LL, LR, RL, RR) impulse response
--> Samples per channels should less than 1000000* for stereo
--> Samples per channels should less than 400000* for full stereo
--> Impulse response file support: V4A IRS, FLAC, WAV
Notes:
Convolver have been tested working even in stereo impulse response with 16121304 samples per channels on Snapdragon 820
Supported platform:
1. It should support from KitKat to Nougat.
2. Tested on arm or x86 architecture devices.
Release/Download: https://github.com/james34602/JamesDSPManager/releases
If you look at the source code from Java part, you will find some are similar with Viper4Android, but this is not true.
Viper4Android only open source it's interface, their core drivers source code have never been released.
For convenient sake, I copy some interface code to accelerate my development.
How to compile the source code?
Use eclipse && Android NDK will do the job.
Previous post: https://forum.xda-developers.com/android/apps-games/app-omnirom-dsp-manager-rom-extra-t3185961
Screenshot:
Click me!
This guy are cool! They have tested to use JDSP with v4a! https://forum.xda-developers.com/apps/magisk/module-jamesdspmanager-2017-10-15-v1-1-t3689390
I reach my milestone and made 14 Band Equalizer works @ 32, 64, 126, 200, 317, 502, 796, 1260, 2000, 3170, 5020, 7960, 13500 and 15000 Hz
And more nice bass filters
I have done more on optimize the audio engine, it use less and less CPU usage than before.
So far I have update:
Pure stereo widening.
Reduce band number to 12 bands.
great! this is purely cpu based? can it be hardware accelerated for less CPU utilization?
also a flashable zip would be nice
Tunnel player?
james3460297 , looks very promising. would this bypass the tunnel player that most Samsung phones use allowing for audio visualizers to work?
@james3460297 ... any plan to support magisk module for this ... seems promising. thanks for the works :good:
adewisman said:
@james3460297 ... any plan to support magisk module for this ... seems promising. thanks for the works :good:
Click to expand...
Click to collapse
Currently, I don't have plan to do so, because I don't have magisk framework development experience...
james3460297 said:
Currently, I don't have plan to do so, because I don't have magisk framework development experience...
Click to expand...
Click to collapse
You can check out this module:
https://forum.xda-developers.com/apps/magisk/module-jamesdspmanager-2017-10-15-v1-1-t3689390
If you want to take over development/maintenance of this module I am happy to give you repo ownership, otherwise I don't mind keeping it updated too.
s8m said:
You can check out this module:
https://forum.xda-developers.com/apps/magisk/module-jamesdspmanager-2017-10-15-v1-1-t3689390
If you want to take over development/maintenance of this module I am happy to give you repo ownership, otherwise I don't mind keeping it updated too.
Click to expand...
Click to collapse
I don't have extra time maintain, you could help keeping update if you like to
Before this latest update, I did a lot of test on high efficiency convolution engine, it's CPU consumption are much less than b4
Arm64 support? And do i have to uninstall any sound modifier before install jsdp?
toji12 said:
Arm64 support? And do i have to uninstall any sound modifier before install jsdp?
Click to expand...
Click to collapse
It looks like it works fine on my phone (MT6755, ARM64, Android 7.0) without any additional steps. I just flashed JamesDSPManager-v1.5-HQ-Auto.zip via TWRP recovery. I didn't remove anything or do other things.
James, would it be possible to add a parametric EQ where users can add custom frequencies and Q factor.
There is no parametric EQ on Android that works systemwide, i hope yours will.

[GUIDE] [SOUND MOD] Viper4Arise ***Best sound experience on Android***

After trying out a lot of different sound mods and apps and patches I always came back to Viper4Arise. Simple to use, great sound quality and a lot of customization.
There are many Arise editions but I find the attached one simplest to use.
Steps:
1. Flash the attached file (ARISE Sound Systems Deuteronomy 2.2.3 Mac 'n Cheese Edition FINAL) through TWRP
**For Android Oreo flash the included (ViPER4Android_2.5.0.4_Wonder_Wicked_Witch_12-Jan-2018.zip) file through TWRP instead.**
2. Reboot to OS
3. Install Busybox (https://play.google.com/store/apps/details?id=ru.meefik.busybox) from Play Store
4. Open the Busybox app and install busybox
5. Enter the Viper4Arise app
Done!
Next, you need to set up the sound mod.
*I only use Viper4Arise for my headphones so I will cover only that part but you could test out different settings for other audio outputs*
In the Viper4Arise's menu go to UI setting and set it to expert.
Go to Headset and click Enable, I suggest you put on your headphones now so you can hear the changes in the sounds yourself and tweak them to your liking.
My settings on Redmi 4X are:
Spectrum Extension (enabled): Strength: 0,5
FIREqualizer (enabled): Preset: Acoustic
Convolver (enabled); Impulse Response: BBE2.irs (extract the attached BBE 2.rar into Viper4Android/Kernel); Cross Channel: 30%
Dynamic System (enabled); Listening Device: High-end headphone v2; Dynamic Bass:5%
Viper Bass (enabled); Bass mode: Natural bass; Bass Frequency: 100 Hz; Bass Boost: 3,5 dB
Viper Clarity (enabled); Clarity mode:Natural; Clarity:6 dB
wow your profile settings and irs file make the sound on my headset amazing ??? thx ?
How much sound difference between viper and a dedicated dac say dragonfly black?
Del 10char

[Magisk] [Module] STEREO-HIFI-PREMIUM to AOSP 9.0

STEREO-HIFI-PREMIUM only for AOSP 9.0.
Author Big_Brazer , I just tested and made it a module for Magisk.
This is not a port , the mod is made entirely on the aosp 9.0 files of our device.
Not to be confused with the stereo mod for two speakers, this is not about it.
*
v1.4
The sampling frequency of the audio is increased to 862000hz
Audio frequency up to 32bit
The Bluetooth A2DP driver now has support for 128bit 768000hz.
Improved effects surround_sound the back of the stage and improved audio depth.
===
v1.5
Activated Auro 11.1
*
It is recommended to install on a clean system without any audio modifications in the form of Dolby, ViPER4Android and others because they still cut the quality of the signal under its configuration.
P.S. perhaps they you more not will need.
How to check if it's working ???
v1.5
Activated Auro 11.1
For what is this mod ? I just edit mixer paths to 92 lvl instead of 72 and sounds wonderful .
noskojv said:
v1.5
Activated Auro 11.1
Click to expand...
Click to collapse
Well you changed the mp3 decoder's channel-count from 2 to 11.1, it's really make sense?
Developer. said:
Well you changed the mp3 decoder's channel-count from 2 to 11.1, it's really make sense?
Click to expand...
Click to collapse
I'm not the author. Try and find out.

Categories

Resources