Related
[MOD SOUND] ViPER4Android FX & XHiFi ANDROID 2.3/4.0/4.1/4.2 (GB & ICS & JB)
ViPER4Android
FX 2.2.0.7 & XHiFi 2.1.0.0
2.3/4.0/4.1/4.2 (GB & ICS & JB)
Short description:
Equalizer with a variety of effects.
Description:
V4A FX version: Adds a variety of sound effects (visualization of sound).
V4A XHiFi version: Restores sound quality.
V4A FX and XHiFi together: More sound settings, the cat. make the sound quality is much nicer.
Specifications
Codename: (FX version) Beautiful / (XHiFi version) X-Factor
Supported OS: Android 2.3 / 4.0 / 4.1 / 4.2
Supported hardware: ARM (ARM15, Cortex A8/A9 or higher).
FX min. requirements (Convolver off): A8 300MHz or ARM11 500MHz.
FX min. requirements (Convolver included): A8 single-core 800MHz, recommended dual-core or quad-core 1.2GHz.
XHiFi min. requirements (all effects included): A8 dual-core 1GHz or higher, Tegra2 processor supported.
Supported languages: English (United States) / Simplified Chinese / Traditional Chinese.
Screenshots
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Download FX-version:View attachment ViPER4Android_FX_2207_en.zip
Download XHiFi-version:View attachment ViPER4Android_XHiFi_2100_en.zip
IRSamples for Convolver:View attachment IRSamples.rar
Recommended settings from the author
ViPER4Android_FX
<Headset>
1. Master Power: ✔
2. Playback Gain Control
(1) Enable checkbox: ✘
(2) Select Effect Strength: Slight
(3) Max Gain: 4x
(4) Max Output: -1.9dB
3. FIR Equalizer
(1) Enable checkbox: ✘
(2) Select Preset: Acoustic
(3) Linear Equalizer graphic: default
4. Convolver
(1) Enable checkbox: ✔
(2) Impulse Response: PopEQ // DBX 160SL Blue - Medium Ratio // JoeMeek SC2 Impulse
5. Field Surround
(1) Enable checkbox: ✘
(2) Select Field Surround Strength: Extreme
(3) Select Mid Image Strength: Extreme
6. Reverberation
(1) Enable checkbox: ✘
(2) Room Size: 25m2
(3) Sound Field: 5m
(4) Damping Factor: 0 Percent
(5) Wet Signal: 0 Percent
(6) Dry Signal: 50 Percent
7. Dynamic System
(1) Enable checkbox: ✘
(2) Select Listening Device: Common Earphone(v2)
(3) Select Dynamic Bass: 0 Percent
(4) Tube Simulator(6N1J): ✘
8. Master Gate(Limiter)
(1) Ouput Gain: 0dB
(2) Limit Threshold: 0dB
<Phone Speaker>
1. Master Power: ✔
2. FIR Equalizer
(1) Enable checkbox: ✘
(2) Select Preset: Acoustic
(3) Linear Equalizer graphic: default
3. Convolver
(1) Enable checkbox: ✔
(2) Impulse Response: Studer +1dB Updated
4. Reverberation
(1) Enable checkbox: ✘
(2) Room Size: 25m2
(3) Sound Field: 5m
(4) Damping Factor: 0 Percent
(5) Wet Signal: 0 Percent
(6) Dry Signal: 50 Percent
5. Extra Loud
(1) Enable checkbox: ✘
(2) Select Effect Strength: Slight
(3) Max Gain: 4x
(4) Max Output: 0dB
6. Master Gate(Limiter)
(1) Ouput Gain: 0dB
(2) Limit Threshold: 0dB
ViPER4Android_XHiFi
1. Master Power: ✔
2. Playback Gain Control
(1) Enable checkbox: ✔
(2) Select Effect Strength: Slight
(3) Max Gain: 4x
(4) Max Output: -1.9dB
3. FIR Equalizer
(1) Enable checkbox: ✔
(2) Select Preset: Acoustic
(3) Linear Equalizer graphic: default
4. Audio Reconstruction
(1) Enable checkbox: ✔
(2) Hi Clarity: 50
(3) Lo Contour: 70
5. Master Gate(Limiter)
(1) Limit Threshold: 0dB
installation
1) Download and unzip the IRSamples.rar the root of the SD-card (SD-card\Viper4Android\Kernel\*.irc)
2) Set the selected ank (FX or XHiFi) of acc. file - can be both, because they get along well together
3) apk run and follow the instructions appearing on the screen
And for other system Poweramp music players (e.g., MIUI music player, Apollo, etc.
From version: FX v2204, XHiFi v2007:
To make it work with V4A Poweramp correctly, you have to both applications (FX and XHiFi), switch to Compatible Mode and then reboot the phone.
CODEC CHOOSE WHAT?
NEW! Starting with version FX 2207:
ZTE U880 or same CPU (PXA920), choose - "PXA920 without VFP" (Convolver disabled)
Tegra2 or any CPU with freq equal / less than 800MHz, choose - "ARM with VPF"
Qualcomm of freq higher than 800MHz - single core, choose - "A8 with NEON"
ALL other Dual-core, Quad-core, Octa-core, choose - "A9/15 with NEON"
NEW! Starting with version: XHIFI 2100
Tegra2, choose - "NVIDIA Tegra2"
ALL others, choose - "CortexAx with NEON"
Homepage: Original theme author on XDA <-> Original theme author's Chinese website
IRS samples for convoluters (convolver)
IRS samples for convoluters (convolver) thanks tranceman111
So what is the convolver (Convolver), and what it eats? try to understand
Start by asking the concept - "Reverb"
"Reverb - a reflection of sound from the different items that surround it (walls, floor, ceiling, windows, bookshelves, trees, houses and even people.) Any sound that we hear in life, is not a pure signal, and contains themselves more and their reflections on the various surfaces. "
Convolution reverb or just convolver
It is also called convolution reverb and pulse. It uses impulse responses of the various processing facilities or equipment (other reverbs), repeats the distribution of fluctuations in the original.
More information can be read: here and here
IRS (Impulse Response) - is an impulse response in the form of short Wave files that are loaded into convoluter, through which he recreates a mathematical model of a room, reverb, devices, etc. from which recorded (shot) pulse! (ie the impulse response contains a linear response of your system (ie frequency response), and does not include the non-linear characteristics (ie distortion / color).
PULSES
Technics Vintage IRS
[Pulses with vintage equipment Technics (1978 issue) preamp and power amp.
Technics+Vintage+v4
Presets+Technics+Equ
Version for those who do not pull the processor (wheezing, stuttering, delay, etc.)
Technics+SU-9011(Preamlifier)+&+SU-9021(PowerAmplifier)+LITE+IRS
Presets+Technics+Equ+Lite
SuperLight Technics Vintage v4
SuperLight Preset Technics Equ
later
WORK Beats Audio, SRS, Dolby mobile, xLOUD + ViPER4Android FX & XHiFi
To work sound effects Beats should be laid out in this thread I've found (system / etc / audio_effect.tsonf) before installation and after installation. I made the necessary Changes to your firmware.
audio_effect.conf to put the replacement in
/ system / etc / audio_effect.conf
Restart the phone.
Full work
[ROM][Sense 4.1][20.01] Team Venom presents: ViperS 1.6.3 - welcome to the future.
View attachment audio_effects.rar
FAQ Reserv
Q: What makes this program?
A: This program is a conventional equalizer with a wide list of options, working with almost all the players.
Q: How do I install?
A: Set yourself ank, run and follow the instructions poyavivscheysya. If the default setting does not help, use FLASHABLE-version.
Q: Why the program needs ROOT?
A: Then, what driver (library) that are required to operate the program prescribed (set) in the section: system / lib /
Q: What kind of CPU to choose for my device?
A: Table of compliance processors, see the cap under the spoiler.
Q: Where to copy files (samples) for Convolver'a?
About: SDCard/ViPER4Android/Kernel / - Case of letters dlozhen be strictly adhered to!
Q: I downloaded a new impetus to the device for the convolver, and the device does not see them, why?
A: Advice to all who do not work convoluter, make sure that the files pulses *. Irs you have piled up in a heap in the folder ViPER4Android/Kernel rather than sorting into folders.
Q: What is the format (extension) to be in the sample?
A: Since version 2.2.0.3 (2.0.0.6) and further, the file extension "Nonlinear processing" (aka Convolver) with. Wav replaced by. Irs
Q: How to make the new drivers? After all, there is laid only apk.
A: Install the program and open it, it will offer to update the driver.
Q: How do I use different pulses are then laid out? I put a version XHiFi, but there is no any choice of these same effects ...
A: The pulses are designed to convoluter (convolver), cat. there is only a version of the FX! At the root of the memory card create a folder: / ViPER4Android/Kernel / and there throws impulses. Now, where in the program choose the right impetus.
Q: I have a program does not work with PowerAmp'om. What to do?
A: To get to work with V4A Poweramp correctly, you have to both applications (FX and XHiFi), switch to Compatible Mode and then reboot the phone.
In: Switch from Normal to Compatible and still with PowerAmp does not want to. Maybe something else to turn on or off in PowerAmp? Prompt?
A: PowerAmp need to go to Settings-> Sound-> Advanced Settings-> put a checkbox on musicfx. Then tab tone / volume set compulsory treatment by activating point musicfx (in this case in the system settings must be activated V4A), long press on musicfx otkryvaetsya equalizer that are currently using the system.
Q: When installed a program, and tried to find the driver Toli Toli update I wrote this: "please comfirm your phone has been rooted and busybox installed". What do I do?
A: First, the program will necessarily need ROOT-law, and secondly, we must also install Busy Box. It select the smart installer and reboot.
Q: What's the difference between versions XHiFi?
About: V4A XHiFi version is mainly to restore the sound quality and detail. This is the main feature of XHiFi, making detailed and high frequencies to restore losses to MP3 audio files.
In install the latest version of V4A through AIC. Install both the equalizer. On the second why you do not have the settings for the speaker. This is as it should be or cant install?
About: XHiFi intended only for the headset (headphones) / BT, but if you want to use XHiFi for the speaker, then simply activate the lock effect mode in XHiFi application.
Q: Can I use them both at the same time or just individually?
A: You can either - they get along well together and complement each other perfectly.
Q: I installed both versions, but activate only one of them, and in the process both hang. Why is that?
A: It does not matter which version you have activated - FX or XHiFi, they will still always be run together (provided that they are installed both).
Q: If fx is the driver, should be put hifi, whether or not the driver put it?
A: Yes, on the first run, the program will prompt you to update draver.
Q: There are significant differences from the DSP Manager is available?
About: V4Android partly based on the source code of the DSP Manager, that is, in fact, it is more advanced (improved) version of it.
Q: And now all in one file? Previously, there was also a manager. Explain.
A: Since version 2.2.0.4 (2.0.0.7) and further, manual installation is now - will not be as program itself will update the driver at startup.
Q: Unpacked impulses for convoluters, but the application of sound stutters. Tell me what's the problem?
A: The processor is unable to cope. Disconnect convoluter.
Q: How to use this non-linear processing? Which of this heap of files in the format. Irs stand for improvement?
A: Anyone, what you enjoy. They are all in their own way alter the sound, so only you can choose what you like.
Q: Can me more about the actual samples? Everything can be put right? And at some specified phone model, what is it?
A: Yes, you can throw all the samples in a single folder. If on a sample contains the model number, so this phone has some kind of his trademark uluchshayzer (such BeatsAudio from HTC), while the use of which was filmed sample (using the spec. Equipment).
Q: What is the mode of Safe Mode (Safe Mode), and what is it for?
A: If you V4A not work with any player, then try switching to Safe Mode, cat. and is designed to work with almost any music player with a cat. V4A does not work in Normal Mode (works only with the Android 4.X and above).
Q: What is the mode Compatible Mode (compatibility mode) and what is it for?
About: Compatible Mode supports a larger number of both system and third-party music players and players with their own sound effects or EQ (works only with the Android 4.X and above).
In: Switch to Compatible Mode, and I wrote that the Driver status: NO
About: Driver status in V4A FX Compatible Mode will always show - NO. YES will show only in Normal Mode - this is a bug of the program.
In: Switch to Compatible Mode, reboot, but nothing changed ... (Option 1)
A: If you want to use Compatible Mode, then you need to switch to this mode, both applications (ie, both XHiFi and FX).
In: Switch to Compatible Mode, reboot, but nothing changed ... (Option 2)
A: For those who still remained a problem with effects in Compatible Mode, even after a reboot, do the following: Locate the file - / system / build.prop and change the line with: Ipa.decode = true on lpa.decode = false
Q: Why ViPER4Android FX always leads to FC when headphones?
A: Most likely you have not write to the partition / system / on the device, so the drivers were not installed. Allow entry to the system partition and reconfigure the automatic installation of drivers or install them manually.
Q: Why ViPER4Android FX creates unexpected sound effects, cat. not observed (or different) from other users?
A: First, try to clean the data ViPER4Android FX, and if that is unsuccessful, then make sure you do not stand the sound of the amplifier.
Q: Why ViPER4Android FX will not boot after boot device?
A: Check your antivirus, or else V4A was off the list of startup.
Q: Why do missing V4A effect after using task-killer'a?
A: Just add ViPER4Android FX to the list of excluded task-killer'a.
Q: Why V4A effect suddenly disappears?
A: Because the Android system kills some processes due to memory limitations. Just set ViPER4Android.apk as system application (move it to / system / data / and reboot the device.)
Q: Why there is background noise when using v4a effects?
A: This error Android, cat. they will all sound modes (BeatsAudio, etc). Try to rename the file: / system / lib / SoundFX / libbundlewrapper.so in libbundlewrapper.so.bak, and reboot the device.
Q: I'm trying to install the program, wrote that the driver is not installed. Check for root and biziboks. Both are found in the catch, I do not understand ...
A: Perhaps you should not permit entry in the system, so the driver and did not put. Try to install the drivers manually for this instruction.
Q: Tell me, in the status of the driver, the value of treatment - no, it's that it does not work or does not work?
A: Status: Processing - NO (if the music is not playing); Processing - YES (if the music is playing).
Q: What is the Cure +?
A: When listening to music, with a normal audio system for more than three hours, you'll start to feel fatigue, dizziness, tinnitus, irritation and other ailments. This is a normal reaction of the body, as heavy bass and loud sound can cause permanent damage to the human auditory system. But from these symptoms can easily get rid of - just enough, just relax a bit. Viper is also the professional tool for listening to music, so we decided not to ignore the problem. We put a lot of effort to develop a more "innocent" technology listening to music, and have achieved little success. But think about how to give users the opportunity to experience it. It is this "little success" and is a technology - Cure +. But we are still working on how to better present this technology to the user.
Which music player that you recommended except Power AMP?
baronzelan said:
To work sound effects Beats should be laid out in this thread I've found (system / etc / audio_effect.tsonf) before installation and after installation. I made the necessary Changes to your firmware.
audio_effect.conf to put the replacement in
/ system / etc / audio_effect.conf
Restart the phone.
Full work
[ROM][Sense 4.1][20.01] Team Venom presents: ViperS 1.6.3 - welcome to the future.
View attachment 1978979
Click to expand...
Click to collapse
thanks should i change permission after replacement in
/ system / etc / audio_effect.conf
Rvl7 said:
Which music player that you recommended except Power AMP?
Click to expand...
Click to collapse
I use HTC music player. You can use any player, only need to turn on in the settings ViPER4Android:
And for other system Poweramp music players (e.g., MIUI music player, Apollo, etc.
To make it work with V4A Poweramp correctly, you have to both applications (FX and XHiFi), switch to Compatible Mode and then reboot the phone.
mamdouhn said:
thanks should i change permission after replacement in
/ system / etc / audio_effect.conf
Click to expand...
Click to collapse
Yes
- Go to: / system / lib / soundfx / a RootExplorer
- Make this folder writable
Come-in: / system / etc / a RootExplorer
- Make this folder writable
- Manually put the file there - audio_effects.conf (from the archive below)
- Reboot the device.
baronzelan said:
Yes
- Go to: / system / lib / soundfx / a RootExplorer
- Make this folder writable
Come-in: / system / etc / a RootExplorer
- Make this folder writable
- Manually put the file there - audio_effects.conf (from the archive below)
- Reboot the device.
Click to expand...
Click to collapse
thanks
so / system / lib / soundfx will be rwxr-xr-x
and audio_effects.conf will be rw-r--r--
is it right ?
thx
Very nice thank you
This Mod works perfectly with ViperS 1.6.3 within Htc Music Player (better than any other mod). And please refer to @zhuhang original thread for latest updates.
is there any iinterference with Beats, or it works along with Beats?
DarkLP said:
is there any iinterference with Beats, or it works along with Beats?
Click to expand...
Click to collapse
Works with Beats
Pretty nice....thanks.
"I wanna be the apex of predators in my backyard"
Joe Rogan
Thanks, one question do we need to create folder on sd card ? to copy IRsample.rar there? I cant see any folder created by application after running it. can some one provide exact path with exact name of folders if we need to create manually.
Also how to use these IRsample?
Sent from my Micromax A116 using Tapatalk 2
Works perfect with vipers 3.0.2 along with beats audio. It's amazing, thanks
can i use this on xperia device?
khamim said:
can i use this on xperia device?
Click to expand...
Click to collapse
Yes but goto original thread for more info and latest version. Link in OP and in my Sig.
Sent from my HTC Sensation
How can I make this work on viper jb rom?
Sent from my HTC Sensation Z710e using xda app-developers app
Does it works on ViperS 5.1.0 sense 5 ???
Here is the audio effects that i ever feel the greatest.
It is
ViPER4Android [V4A]
Here is official page http://forum.xda-developers.com/showthread.php?t=2191223
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Version: FX version 2.2.1. 1/ XHiFi Merged
Operating environment: Android 2.3 / 4.0 / 4.1 / 4.2 / 4.3
★ Android 4.3 Support ★
ViPER4Android supports Android 2.3 Ginger bread, 4.0 Ice Cream Sandwich and 4.1 upto 4.3 Jelly bean firmwares.
★ NEW Channel Pan ★
Controls left/right channel output. Its not very useful unless your headphone is imbalance or faulty one side. It will be a cure for you.
★ NEW Differential Surround / Haas Effect ★
This is an old feature which ViPER520 had removed from FX in early days.
But after many users requesting it, ViPER520 bring it back to FX
More info on Haas Effect: http://www.mixcoach.com/creating-dep...haas-effect-2/
★ NEW ViPER Fidelity Control ★
★ ViPER Bass ★
With 2 bass mode, you can have greater bass experience than before! This requires a little bit better headphone.
★ ViPER Clarity ★
With the latest Clarity mode selection, you can balance up heavy bass with high clarity audio that you can never imagine before!
★ NEW Headphone Surround Engine+ ★
★ NEW Cure Tech+ ★:
With normal audio system, listening for more than three hours will feel fatigue, dizzy, tinnitus, irritated and other symptoms. This is a normal reaction, heavy bass and high volume could cause permanent damage to the human auditory system, but other phenomena can restore through resting.
Viper as a listening experience professional will not ignore this problem. Therefore put a lot of effort to study how to make a "Healing" sound technology, just a small success. But thinking on how to let users experience it.
★ NEW In-App Installation ★:
With this in-app installation, users just have to follow the instructions when first run V4A app and the app will install everything for you.
In order to use this feature successfully, full Busybox must be installed.
★ NEW Compatible Mode (Only in 4.x) ★:
Compatible Mode supports large variety of music players and the players' own EQ/sound effects (system-provided/third party)
Therefore, you don't have to select V4A in Sound Settings > Music Effects, choose anything other than V4A. Just run V4A app and the effects will be working with anything else.
1. In option, switch to Compatible Mode. Reboot, done.
2. In Sound Settings > Music Effects, choose other than V4A.
3. Run V4A app and configure the settings then the effects will work together with the one you chose in Sound Settings.
★ NEW Safe Mode (Only in 4.x) ★:
If V4A dont work on many players, try switching to Safe Mode to work with almost any music player.
1. In option, switch to Safe Mode. Reboot, done.
Bugs/Issues:
1. Driver status in FX Compatible Mode always NO. Driver status will show YES in normal mode.
Latest Version Changelogs
FX version: v2.2.1.1
1.Add differential surround (Haas effect).
2.Add channel pan setting.
3.More settings for field surround.
4.Support android 4.3.
FX version: v2.2.1.0
1.Added XHiFi Clarity mode.
2.V4A XHiFi stopped development.
For your information:
XHIFI Hi Clarity = FX Viper Clarity > XHiFi Clarity Mode.
XHIFI Lo Contour = FX Viper Bass > Natural Bass Mode.
FX version: v2.2.0.9
1.Add fidelity control system.
2.Optimize Headphone Surround Engine+ for VFP platform.
3.Fix some bugs.
4.Add update check.
FX version: v2.2.0.8
1.Add Headphone Surround Engine+.
2.Fix some bugs.
XHiFi version: v2.1.0.2
1.Support speaker effects.
2.Fix some bugs.
Click to expand...
Click to collapse
DOWNLOADS
FX version v2.2.1.1 : http://www.mediafire.com/download/7t1c73wsz4qiygu/ViPER4Android_FX_2211_en.zip
XHiFi version v2.1.0.2 : http://d-h.st/4WM
Sony Xperia New S.Enhance IR Samples Rev2: http://forum.xda-developers.com/showthread.php?p=41320703
Creative ZEN X-Fi IR Samples: http://forum.xda-developers.com/show....php?t=2308239
IRSamples for Convolver(Updated 15Apr) : http://www.mediafire.com/download/9am1sogfq9lm31d/en_IRSamples_331+IR.zip
For more IR samples, visit V4A IR Sample Index Thread with Official Mirror, all new IR samples were uploaded here : IRSamples
HighDefinition Impulse Responses Samples (IRS) - (stereo, 24bit, bitrate: 2823 kb/s, 44100 Hz, 2 channels)
BBE 1-5
Unofficial V4A Tool by a vipersaudio member - Fix FX not working for many players below 4.3:
http://d-h.st/c4Z
Click to expand...
Click to collapse
INSTALLATION
Require Rooted,BusyBox
Which to install? FX or XHiFi or Both?
A: FX has many audio effects, where as XHiFi restores audio quality. If you like many effects(reverb, bass, surround) then choose FX, if you like clear audio/vocal and you have a good headset, choose XHiFi. You can also install both, more CPU usage, that's all.
[FX/XHiFi version]
1. Extract zip
2.Choose correct android version & Install ViPER4Android.apk
2. Run app, when prompt, choose Yes to "install/update".
3. Choose correct CPU Type. (Instructions include in your downloaded zip)
4. Reboot device.
Option1. Choose V4A(either fx or xhifi) in sound settings > music effects (Don't worry, both fx and xhifi wil run together)
Option2. Dont touch sound settings, open up both(fx and xhifi), in option, switch to FX Compatible Mode, reboot.
Update To Latest Version
1. Download latest FX and XHIFI apks
2. Copy to system/app to overwrite // OR // Install like normal and replace previous version.
3. Open up FX and XHIFI, Choose "Install/Update"
4. Reboot, done.
UNINSTALLATION
1. In both FX and XHiFi app, go option and choose uninstall driver.
2. After that, uninstall the apk itself.
3. Reboot.
Click to expand...
Click to collapse
For IR Samples (Impulse Response)
1.Download it and extract to sdcard/Vi4PERAndroid/kernel (if folder does not there,jump to step 2 and then step 1)
2.Open Vi4PERAndroid,check box "impulse response"
3.Select desire samples
Changed Driver List (Corrected 20/May)
For Galaxy S Advance,Choose Cortex A9/15 with NEON
NEW FX 2208+
ZTE U880 or same CPU(PXA920), choose "Without VFP (PXA920)" (Convolver and Surround+ disabled)
Tegra2, ARM or any CPU with freq equal/less than 800MHz, choose "With VFP"
All Qualcomm/Snapdragon of freq higher than 800MHz, regardless of cores, choose "CortexA8 with NEON"
All other Dual-core,Quad-core,Octa-core, choose "CortexA9/15 with NEON"
NEW XHIFI 2101+
ZTE U880 or same CPU(PXA920), choose "Without VFP (PXA920)"
Tegra2, ARM, choose "With VFP"
ALL others, choose "CortexAx with NEON"
Click to expand...
Click to collapse
★★★For those having problems with effects in compatible mode even after rebooting. Try this:
1.Open up /system/build.prop (If you can't find this line, you have to solve in other way)
2.Change the line Ipa.decode=true to lpa.decode=false
Trouble Shooting
When V4A is not working for you. (Really No effect for all options, NOT BY CHECKING driver status)
0. MAKE SURE YOU HAVE CHOSE THE CORRECT DRIVER. Refer OP.
1. MAKE SURE YOU HAVE BUSYBOX INSTALLED
2. Uninstall, reboot. Reinstall, Choose correct driver, reboot.
3. Don't use compatible mode yet, go to sound settings>music effects> and choose v4a(either fx or xhifi). Test.
4. If not working, switch to compatible mode, reboot, go to sound settings>music effects> and select previous effect. Test.
5. If not working, activate safe mode, reboot. Test.
Click to expand...
Click to collapse
CREDIT
ViPER520(creator) and zhuhang
FX & XHiFi Settings Explained & Recommended Value
FX Settings
V4A FX version mainly for rendering audio effects, by controlling various parameters to achieve the purpose of audio effect adjustment.
<Headset>
1. Master Power. This option defines whether to enable V4A headset sound effects, also known as main switch.
2. Playback Gain Control :
It is mainly used to dynamically control the audio volume, to amplify or to attenuate.
(1) Enable checkbox : Whether the effect is enabled.
(2) Select Effect Strength : Effect Strength is the speed of amplification or attenuation, the stronger the faster the speed and the higher the final volume, the weaker the slower the speed, the closer to the original volume. Recommended medium.
(3) Max Gain : When the volume of the note is too small, in order to uplevel the sound, there may be very large magnification. The higher the value, the louder the volume. But too large will also amplify the noise within the song. Recommended 4 times.
(4) Max Output : This value defines the maximum volume of the PlaybackAGC sound in decibel value, the greater the value the greater the volume, 0 db is the maximum. In order to make the sound softer recommended -1.9 dB.
3. FIR Equalizer
511-order 10 bands FIR linear equalizer.
(1) Enable checkbox : Whether the effect is enabled.
(2) Select Preset : Here you can select default equalizer presets. When choosing custom, it will follow the user-defined lines drawn.
(3) Linear Equalizer graphic : Will pop up when you touch the graphic equalizer, you can manually adjust the levels of amplification and attenuation of the 10 bands.
4. Convolver
When an impulse response(IR) sample is loaded, music will show the same characteristics of the loaded sample, for example equalizer, surround, reverberation, tube etc.
Make sure SD Card has /ViPER4Android/Kernel/ folder, IR samples will be located there. If folder not exists, you can download latest V4A FX and extract SDCard_V4A.zip.
(1) Enable checkbox : Whether the effect is enabled.
(2) Impulse Response : Here you can select and load IR Samples inside /ViPER4Android/Kernel/ folder.
5. Field Surround
It is mainly used to create sound field surround effects. The sound field can be understood as mono field or stereo field.
(1) Enable checkbox : Whether the effect is enabled.
(2) Select Field Surround Strength : This value defines the strength of the field surround effects. The stronger, the stereo effect will be more obvious, the sound will come from left and right sides. Recommended medium.
(3) Select Mid Image Strength :This value defines the central vocal intensity. More strongman sound more clear, the weaker the more ethereal sound.
6. Reverberation
It uses mathematical methods to simulate the environmental feeling sensation. Example a song can be felt playing inside the auditorium, living room, bathroom, and so on.
(1) Enable checkbox : Whether the effect is enabled.
(2) Room Size : This value defines the virtual environment area size. The larger the value, the sound is wider and more echoes.
(3) Sound Field : This value defines the width of the room above, in meters. Assumed that the above room size is 100 square meters, here to set a width of 14 meters, then the length of the room will be 7.14 m.
Therefore, the room size and width defines the aspect ratio of the virtual environment.
The larger the value, the sound coming from both sides will felt more obvious.
(4) Damping Factor : This value defines the humidity of air in the above virtual environment, the moisture vapor in the air will easily absorb the echoes.
So the bigger this value, the less echoes heard.
(5) Wet Signal : This value defines the volume of the simulated environment effect.
(6) Dry Signal : This value defines the volume of the original sound.
For environments with low air humidity such as living room, auditorium and other indoor environment, you can use room size and sound field to define the area of the virtual environment, water vapor content values from 0 to 20, the reverb signal values 20 to 50, the proportion of the original signal to take value of about 50.
For environments with high air humidity such as bathroom and other indoor environment that contains a lot of moisture, you can use room size and sound field to define the area of the virtual environment, water vapor content values of 50 to 100, the reverb signal values 40 to 80, the proportion of the original signal value of about 50.
7. Dynamic System
It handles the dynamic range of the sound. In other words the bass, treble, and limiting.
(1) Enable checkbox : Whether the effect is enabled.
(2) Select Listening Device : This value defines the headset type connected to the audio jack. If you cannot get the right device for good bass tone, then select Common earphone. Common earphone is a common choice. Recommend Common earphone.
(3) Select Dynamic Bass : This value defines the average dynamic bass, the greater the stronger bass. Recommend 33%.
(4) Tube Simulator(6N1J) :This option defines whether to enable tube simulator effect. V4A tube simulator uses a simplified mathematical simulation of tube effect.
If turned on, will greatly reduce high-frequency odd harmonic distortions, while increases even-order harmonic distortions of tube simulator.
8. Master Gate(Limiter)
This option is V4A output limiter, its used to prevent overloud clipping distortion.
(1) Ouput Gain : This value defines the main output volume. Its something like a volume control.
(2) Limit Threshold : This value defines the limits of waveform amplitude by the limitor, 0 dB is the maximum value.
The smaller the value, the easier to experience audio frequency compression(the smaller the volume), will lose sound details, but can effectively control the final output volume. Recommend 0 db.
<Phone Speaker>
1. Master Power : This option defines whether to enable V4A speaker sound effects, also known as main switch
2. FIR Equalizer : Same as headset equalizer.
3. Convolver : Same as headset convolver.
4. Reverberation : Same as headset reverberation
5. Extra Loud
eXtra-Loud further amplifies the sound, but is controlled to protect the speaker, will not overload.
(1) Enable checkbox : Whether the effect is enabled.
(2) Select Effect Strength : Effect Strength is the speed of amplification or attenuation, the stronger the faster the speed and the higher the final volume, the weaker the slower the speed, the closer to the original volume. Recommended medium.
(3) Max Gain : When the volume of the note is too small, in order to uplevel the sound, there may be very large magnification. The higher the value, the louder the volume. Recommend infinity.
(4) Max Output : This value defines the maximum volume of the EL sound in decibel value, the greater the value the greater the volume, 0 db is the maximum. Recommend 0db.
6. Master Gate(Limiter)
Same as headset limiter.
XHiFi Settings
V4A XHiFi version mainly for restoring audio quality and details.
1. Master Power
This option defines whether to enable V4A headset/bluetooth sound effects, also known as main switch.
2. Playback Gain Control : Same as FX version's PlaybackAGC.
3. FIR Equalizer : 2047-order 10 bands, quality much better than FX version. Method of adjusting same as FX version.
4. Audio Reconstruction
It is XHiFi's core feature, it does the detailing and treble restoring for lossy mp3 audio files. (Currently in adjustment phase, different device may have different experience.)
(1) Enable checkbox : Whether the effect is enabled.
(2) Hi Clarity : This value defines the detailing and treble restoration percentage, the larger the value, the more details of the sound and stronger treble.
For low-end/common earphones, this is not recommended as you may experience high frequency shrills.
For better earphones such as Monster,Philips,Zombie,Sennheiser, recommended value = 30 ~ 50.
For high-end headphones, value depands on headphone cable length. Start with value = 40, value +10 for every 80cm cable length.
For preamp/amp connect to phone. Start with value = 60, value +10 for every 80cm cable length.
For tube amplifier, directly use value = 100.
(3) Lo Contour : The value defines the percentage of bass contour reconstruction over total band. The larger the value, the stronger the bass, but midrange and details will slightly lost.
For earphones recommend value = 50 ~ 70.
For headphones recommend value = 20 ~ 30.
5. Master Gate(Limiter)
This option is V4A output limiter, its used to prevent overloud clipping distortion.
(1) Ouput Gain : This value defines the main output volume. Its something like a volume control.
(2) Limit Threshold : This value defines the limits of waveform amplitude by the limitor, 0 dB is the maximum value.
The smaller the value, the easier to experience audio frequency compression(the smaller the volume), will lose sound details, but can effectively control the final output volume. Recommend 0 db.
Recommended FX Settings (will differ with official post)
<Headset>
1. Master Power: ✔
2. Playback Gain Control
(1) Enable checkbox: ✔
(2) Select Effect Strength: Slight//Moderate
(3) Max Gain: 4x//8x
(4) Max Output: -1.9dB
3. FIR Equalizer
(1) Enable checkbox: ✔
(2) Select Preset: Acoustic
4. Convolver
(1) Enable checkbox: ✔
(2) Impulse Response: PopEQ // DBX 160SL Blue - Medium Ratio // JoeMeek SC2 Impulse
5. Field Surround
(1) Enable checkbox: ✘
(2) Select Field Surround Strength: Extreme
(3) Select Mid Image Strength: Extreme
6.Headphone Surround +
(1) VHS+ : ✘
(2) Select Effect Quality: Normal
7. Reverberation
(1) Enable checkbox: ✘
(2) Room Size: 25m2
(3) Sound Field: 5m
(4) Damping Factor: 0 Percent
(5) Wet Signal: 0 Percent
(6) Dry Signal: 50 Percent
8. Dynamic System
(1) Enable checkbox: ✔
(2) Select Listening Device: Common Earphone(v2)
(3) Select Dynamic Bass: 30 Percent
(4) Tube Simulator(6N1J): ✘
9.Auditory System Protection
(1) Cure Tech+ : ✔
(2) Select Binaural Level : Slight
10. Master Gate(Limiter)
(1) Ouput Gain: 0dB
(2) Limit Threshold: 0dB
<Phone Speaker>
1. Master Power: ✔
2. FIR Equalizer
(1) Enable checkbox: ✔
(2) Select Preset: Acoustic
3. Convolver
(1) Enable checkbox: ✔
(2) Impulse Response: Studer +1dB Updated
4. Reverberation
(1) Enable checkbox: ✘
(2) Room Size: 25m2
(3) Sound Field: 5m
(4) Damping Factor: 0 Percent
(5) Wet Signal: 0 Percent
(6) Dry Signal: 50 Percent
5. Extra Loud
(1) Enable checkbox: ✔
(2) Select Effect Strength: Slight
(3) Max Gain: 4x
(4) Max Output: 0dB
6. Master Gate(Limiter)
(1) Output Gain: 0dB
(2) Limit Threshold: 0dB
Recommended XHIFI Settings
1. Master Power: ✔
2. Playback Gain Control
(1) Enable checkbox: ✔
(2) Select Effect Strength: Slight
(3) Max Gain: 4x
(4) Max Output: -1.9dB
3. FIR Equalizer
(1) Enable checkbox: ✘
(2) Select Preset: Acoustic
4. Audio Reconstruction
(1) Enable checkbox: ✔
(2) Hi Clarity: 80
(3) Lo Contour: 70
5. Master Gate(Limiter)
(1) Output Gain: 0dB
(2) Limit Threshold: 0dB
Click to expand...
Click to collapse
Development Progress (Updated 5-Jun-2013)
FX version: v2.2.0.9 (Estimated date: )
1. Optimise Surround Engine+ for VFP CPUs.
XHiFi version: v2.1.0.3 (Estimated date: )
-
TODO List:
1. ViPER4Android driver auto install/update [Done]
2. Increase compatibility for Android 4.x [Done]
3. EQ user-defined slot [Deprecated, use Sound Effect Profile]
4. Sound Effect Profile [Done]
5. XHiFi support Tegra2 [Done]
6. Convolver support ARMv5TE CPU [Done]
7. Improve Convolver process [Done]
8. Convolver support IR Sample of any length [Done]
9. FX Field Surround Upgraded [Done]
10. FX Virtual Headphone Technology added [Done]
11. Fix the sound delay caused by convolver. [Done]
12. Import IR samples from external storage. [WIP]
13. Optimize audio reconstruction module. [Done]
14. Upgrade the bass effect of audio reconstruction module. [Done]
15. Use RootTools to install driver. [Done]
16. Cure Tech+[Done]
17. Add Natural Bass to FX [WIP]
18. Add clarity settings [WIP]
19. Combine FX and XHIFI [WIP]
20. Add Effect Calibration to suit one's ear [WIP]
Effect Calibration:
Every human's auditory systems are not the same, some people experience Left-Right asymmetries, while some with high-frequency phobia. Each individual has a different concept of the sound field. Therefore "Hearing Calibration" was introduced.
Through a simple calibration wizard, V4A system benchmark will be adjusted according to the calibrating result. "Hearing Calibration" feature will make sure every V4A user experience its ultimate effects up to par.
Of course, due to huge "Hearing Calibration" variety, its impossible to cook all the features at once, allow ViPER520 to experiment slowly, as the first edition could only achieve Left-Right symmetric and high frequency calibration.
Click to expand...
Click to collapse
V4A FX GUI Design (Not ready)
thanks:good:
What improvements make this more precise?
Is this better than AC!D Sound Engine?
Sent from my phone, because I'm away from my PC right now
Sami Kabir said:
Is this better than AC!D Sound Engine?
Sent from my phone, because I'm away from my PC right now
Click to expand...
Click to collapse
I've tried both and AC!D sounds better for me.
Sami Kabir said:
Is this better than AC!D Sound Engine?
Sent from my phone, because I'm away from my PC right now
Click to expand...
Click to collapse
For me "YES". I tried almost all song engines such as Acid,DSP,Awesome Beat,Pure Audio& this.I love this more.
Try using different convolvers
I'm sorry for such silly question
But what is IRSamples?
Do i need them?
fongandy said:
I'm sorry for such silly question
But what is IRSamples?
Do i need them?
Click to expand...
Click to collapse
It is Impulse Response.It is optional
1.Download it and extract to sdcard/Vi4PERAndroid/kernel (if folder does not there,jump to step 2 and then step 1)
2.Open Vi4PERAndroid,check box "impulse response"
3.Select desire samples
hermeshhn said:
thanks:good:
Click to expand...
Click to collapse
Please press "THANKS":smile:
Grady22 said:
What improvements make this more precise?
Click to expand...
Click to collapse
OP updated for detail
More IR Samples added:good:
Yeah ! I'm using this mod really cool ! Best working with Google Play Music.. choose setting -> equlizer to viper4android
edit -> I faced some problem with that I think this help to others.
When Activate Mod Sound not wotking with poweramp and some apps (Headset also). for get sound back need to disable Viper4android .
quality sound but need more fixes i think.
Yes,that's right dude
Rom : Umbrella Corporation V2
Kernel : CoCoE 6.2
4cylturbo scripts + CrossBreeder
imcoolsj said:
Yeah ! I'm using this mod really cool ! Best working with Google Play Music.. choose setting -> equlizer to viper4android
edit -> I faced some problem with that I think this help to others.
When Activate Mod Sound not wotking with poweramp and some apps (Headset also). for get sound back need to disable Viper4android .
quality sound but need more fixes i think.
Click to expand...
Click to collapse
To use Viper4android with Poweramp, you must :
- go to settings (of Poweramp)
- go to Audio Engine
- go to Advanced Tweaks
- uncheck "Direct Volume Control"
Envoyé depuis mon GT-I9070 avec Tapatalk
Letin69 said:
To use Viper4android with Poweramp, you must :
- go to settings (of Poweramp)
- go to Audio Engine
- go to Advanced Tweaks
- uncheck "Direct Volume Control"
Envoyé depuis mon GT-I9070 avec Tapatalk
Click to expand...
Click to collapse
yep but i also got ringing problem aswell
Edit - ok working nicely no problem.. I dont know wht happen
imcoolsj said:
yep but i also got ringing problem aswell
Click to expand...
Click to collapse
I never get any problems since the 1st time i used.
WOW! View count nearly 1,000 in my first post. Thank you all
anyone using jetaudio try this out yet?
FX Version 2.2.0.9 update :laugh:
What audio driver un first start i need install ?
Enviado desde mi GT-I9070 usando Tapatalk 4 Beta
[SHARE][PREMIUM SOUND] Noozxoide EIZO-rewire™ PRO (2.0.1.18) & E (1.0.0.12) - Noozy l
http://i.imgur.com/WFVtWdA.jpg
Get the most from your Core Dous sound!!
https://play.google.com/store/apps/details?id=com.noozxoidelabs.eizo.rewirepro
https://play.google.com/store/apps/details?id=com.noozxoidelabs.eizo.rewirep
https://play.google.com/store/apps/details?id=com.dogsbark.noozy
copyright(c)dogsbark.net
https://www.paypal.com/my/cgi-bin/w...63663d3faee8d5348ead9d61c709ee8c979deef3ea735
CLICK HERE TO DONATE TO THE DEVELOPER....
This also work perfectly with ALL ANDROID PHONE AS WELL.
You wouldn't believe your ear,this is pure AUDIOPHILE EARGASM!!
Install this (just updated) and follow this modelling:
>>Go to Settings > Sound > Music Effect > Noozxoide EIZO-rewire™ PRO/E > OK.
>>Open Noozxoide EIZO-rewire™ PRO/E and configure it according to guide below.
ATTENTION: Please don't flash your phone with any audio mods before using this, it's not necessary, just install this one and forget the other audio mods. This apk already include every sound libs needed. If you install/flash any other sound mods, the sound will be terrible!
------------------------------------------------------------------------------------------------------------------------------------
DESCRIPTION of PRO Series
A professional audio modeling processor allows you to reproduce surround sound and high-quality content on movies, music or games. Creates non-channeling virtual surround sound from any audio source, including stereo and mono.
Noozxoide EIZO-rewire™ PRO takes stereo/mono content and uses a virtualizer to create place phantom speakers around the headphone/room, providing a realistic and enjoyable virtual surround sound experience. This equipment is carefully tweaked under "Noozxoide Workbench", the audio research and design laboratory up to 1/24 octave high precision instruments.
Sound images dialog or vocal is tad narrowed, designed to sounds soft in the other words, less aggressive. When master volume is leveling up also increase the aggressiveness dramatically and you got an expensive audio on-the-Go.
This is the latest release with EIZO-SYNC compatible with the future EIZO VSP supports ICS/JB. We deliver you the new [FOCUS] room size, a close-range firing virtual surround sound experience. Sound images are coming from everywhere at a close distance is about 1 meter velocity, makes your contents more exciting and fastpace...Every bit is amazing.
※PLEASE USE PROFESSIONAL HEADPHONE OR PRACTICAL SPEAKERS TO EXPERIENCE IT. RECOMMENDED TO USE HEADPHONE AMPLIFIER. KEEPS AWAY MULTIPLE FILTERS, DO NOT USE 3RD PARTY FILTERS WHICH WILL CAUSED DISTORTION AND MISUNDERSTOOD THE TECHNOLOGIES※
▼ SETUP AS DEFAULT FILTER
-----------------------------------------------------------------------------------------
Settings > Sound > Music Effects > Choose “Noozxoide EIZO-rewire™ PRO Series”
▼ ADVANCED MODELING for MUSIC
-----------------------------------------------------------------------------------------
TURN ON Noozxoide Balanced X-EQ™, Choose “UNIQUE III” from Digital Presets.
TURN ON Noozxoide LogicSurround ES™, set your VSUR room size “Focus/Studio”.
▼ ADVANCED MODELING for MOVIE/GAME
-----------------------------------------------------------------------------------------
TURN ON Noozxoide Psychoacoustic™ II, set the effect strength “Large”.
TURN ON Noozxoide Balanced X-EQ™, Choose “Cinema/Game” from Digital Presets.
TURN ON Noozxoide LogicSurround ES™, set your VSUR room size “Focus/LIVE I/II”.
CHANGELOG
++ Slight UI adjustments.
++ New HD UIs, EIZO-SYNC 1.2 for noozy DFX Switcher.
-- Added VE-Engine, compensate response at -8db to 0db.
-- Added native platform lib “noozxoide_WN_HDMI-a.pmo” HDMI-audio.
-- Handles MKV ultra-high res sampling data streams.
-- Added more (VSUR), (PSYC) effect levels.
-- 100% (zero artifact) Virtualizer (Noozxoide LogicSurround™ ES)
-- Added EIZO-SYNC works with upcoming N Series VSP.
-- 1 octave bassline (Noozxoide MaxxBass™)
------------------------------------------------------------------------------------------------------------------------------------
DESCRIPTION of E Series
A VSP virtual-sound-processor delivers elemental premium sound, whether you are playing favorite (games, watching movie) or listening various genres of musics. The experience allows you to configure more than 4 sound elements (Deep, Warm, Bright, Clear) on your headphones or practical speakers with immersive VSUR, or set it to aggressive and powerful sound on your content...
This time we blended it with a powerful and sophisticated True Voice processor (Noozxoide NogicQ™), is an Q-free true voice processor. It allows you to change sound profiles for your headphone and typically music enthusiast has one or more headphones for listening differ musics. E Series has slightly less Limiter response compare to PRO Series which allows more aggressive sound.
Overall, delivers higher definition True Voice results audible signals with low latency, low noise, extremely low harmonics, tumble-crystal-clear high signal, unique-ty drive out high-driver equipment, pump-in 16k 16Bit/24Bit sampler beating result.
This is a full processor-based modeling series without any parametric filter. Be ready for the natural sound on your music, create heart-pumping. Every bit is amazing...
※PLEASE USE PROFESSIONAL HEADPHONE OR PRACTICAL SPEAKERS TO EXPERIENCE IT. RECOMMENDED TO USE HEADPHONE AMPLIFIER. KEEPS AWAY MULTIPLE FILTERS, DO NOT USE 3RD PARTY FILTERS WHICH WILL CAUSED DISTORTION AND MISUNDERSTOOD THE TECHNOLOGIES※
▼ SETUP AS DEFAULT FILTER
-----------------------------------------------------------------------------------------
Settings > Sound > Music Effects > Choose “Noozxoide EIZO-rewire™ E Series”
▼ ADVANCED MODELING for MUSIC
-----------------------------------------------------------------------------------------
TURN ON Noozxoide NogicQ™, Choose a "Digital Elements" according to your taste..
TURN ON Noozxoide LogicSurround ES™, set your VSUR room size “Focus/Studio”.
CHANGELOG
++ Fix incorrect typos.
++ New HD UIs, EIZO-SYNC 1.2 for noozy DFX Switcher.
-- Fixed forced close on DSP networks (1.0.0.8).
-- Added native platform lib "noozxoide_NogicQ.pmo" an elemental FX.
-- Added native platform lib "noozxoide_WN_HDMI-a.pmo" HDMI-audio.
-- 1.8 octave bassline (Noozxoide MaxxBass™)
------------------------------------------------------------------------------------------------------------------------------------
@All: The entire credit of this superb sound mod goes to the real developer......I am simply sharing the great thing from the Note 2 Forum...
A special thanks to @Crescendo Xenomorph for sharing this awesome thing on xda....
Pro one...
http://forum.xda-developers.com/attachment.php?attachmentid=2347338&d=1382626735
Simple one ...
http://forum.xda-developers.com/attachment.php?attachmentid=2347339&d=1382626735
Always press the THANKS button if helped...
Some awesome Ss....
Dont forget to Press THANKS if helped....
Sent from my Fast and Super Powerful Note 2.... 》《
I've just created this thread for everyone to share their favourite profiles. I've seen similar threads to this but they have been for viper4android and aren't very active. I was hoping people could share what they use for it. I'm personally looking for a rap profile especially for music like Eminem. If someone can share a good profile for that I would really appreciate it.
This is what I'm using currently but looking for something better for rap/hip hop music.
_gemini_ said:
Hi There Guys, Running V4A 2.5.0.5 On The Redmi 2 And Combined My V4A Setup With Mi Sound Enhancer And Custom EQ With Only 6khz and 14khz slightly kicked up and 14khz a bit higher than 6khz frequency. As for the viper settings this is my setup.
Playback Gain Control: Off
FET Compressor: Off
Viper DDCn(Ice Sound Test) Incl In Viper4Arise
Spectrum Extension: Off
Equaliser: Off
Convolver: On (XHR Master Audio) From Vinardos IRS Samples.
Field Surround: Off
Differential Surround: On (Delay Time 8ms)
Headphone Surround: Off
Reverberation: Off
Dynamic System: Off
Tube Sound Simulator: Off
Viper Bass: On (Mode-Subwoofer, Frequency-40hz, Boost-13db)
Viper Clarity: On (Mode-Natural, Boost-10db)
And That's About It, Produces A Hard To Go A Minute Without Listening To Something For A Minute Kinda Sound On My Cheap Volkano Circuit In Ear Buds
Tested Across Different Genres From House, Jazz, Rock And Hip Hop. Hope It'll Give You The Sound You're Looking For
Click to expand...
Click to collapse
//Best profile for headset users//
Just paste both folders (kernel and profile) on Viper4android directory, then open viper4android app and select the respective profile, then look for Convolver options button and select the IRS file that you wish. Enjoy
My Current settings: 22/02/2018
-Headphone/set HyperX Cloud Stinger
-Viper settings
-Spectrum Extension ON: Strength: 0,5
-FIREequalizer ON: Preset: 3,5/6/3/0/0/0/0/0/0/-0,5
-Convolver ON: Impulse Response: BBE2.irs (extract the attached BBE 2.rar into Viper4Android/Kernel): Cross Channel: 30%
-Dynamic System ON: Listening Device: High-end headphone v2; Dynamic Bass:5%
-Viper Bass ON: Bass mode: Natural bass; Bass Frequency: 100 Hz; Bass Boost: 3,5 dB
-Viper Clarity ON: Clarity mode:Natural; Clarity:6 dB
-------------- -------------- --------------
Updated settings: 08/09/2018
-Headphone/set HyperX Cloud Stinger
-Viper settings
-Playback gain control ON: Strength: slight; Max Gain: 2x; Max Output: -1.9dB
-FIREequalizer ON: Preset: 6,5/8/6/1/0/0/0,5/0/
-Convolver ON: Impulse Response: Select the prefered IRS file that you want - Cross Channel: 25%
-Dynamic System ON: Listening Device: Common Headphondv2; Dynamic Bass: 8%
-Viper Bass ON: Bass mode: Natural bass; Bass Frequency: 50 Hz; Bass Boost: 13dB
-Viper Clarity ON: Clarity mode: OZone+; Clarity: 3,5 dB
-Auditory System Protection ON: Extreme
Updated IRS and profile files MEGA: https://mega.nz/#F!c6AXiYqI!7DEcO6cYO6u0iF2KbfF99w
Outdated settings:
-Headphone/set HyperX Cloud Stinger
-Viper settings
-Spectrum Extension ON: Strength: 0,5
-FIREequalizer ON: Preset: 3,5/6/3/0/0/0/0/0/0/-0,5
-Convolver ON: Impulse Response: BBE2.irs (extract the attached BBE 2.rar into Viper4Android/Kernel): Cross Channel: 30%
-Dynamic System ON: Listening Device: High-end headphone v2; Dynamic Bass:5%
-Viper Bass ON: Bass mode: Natural bass; Bass Frequency: 100 Hz; Bass Boost: 3,5 dB
-Viper Clarity ON: Clarity mode:Natural; Clarity:6 dB
BBE_2.rar is empty
Spaceboy60 said:
BBE_2.rar is empty
Click to expand...
Click to collapse
Im using another profile rn tho. do you want to try ?
Mayr1k said:
Im using another profile rn tho. do you want to try ?
Click to expand...
Click to collapse
Sure. Thanks
Spaceboy60 said:
Sure. Thanks
Click to expand...
Click to collapse
In the folder below you can find the IRS files and the profile settings. just paste both folders (Kernel and Profile) on the viper4android folder then from viper4android app select the profile; and from convolver option go to impulse response and select the 50% bass file or whatever you like. comment here if you like my config. (the experience will be amazing if you use headset)
https://mega.nz/#F!c6AXiYqI!7DEcO6cYO6u0iF2KbfF99w
(Thanks to ZhuHang's for the awesome IRS Samples)
Mayr1k said:
In the folder below you can find the IRS files and the profile settings. just paste both folders (Kernel and Profile) on the viper4android folder then from viper4android app select the profile; and from convolver option go to impulse response and select the 50% bass file or whatever you like. comment here if you like my config. (the experience will be amazing if you use headset)
https://mega.nz/#F!Z6hRSKiQ!EyoyGXue-UI1epLwegEIgQ
(Thanks to ZhuHang's for the awesome IRS Samples)
Click to expand...
Click to collapse
Thanks, sounds excellent, maybe gonna turn bass down slightly but that's about it.
Spaceboy60 said:
Thanks, sounds excellent, maybe gonna turn bass down slightly but that's about it.
Click to expand...
Click to collapse
Yeah idk. i use the HyperX Cloud Stinger headset so the sound quality its amazing with those settings
edit: re download the Viper4android folder from MEGA again please (i forgot to update the profile files)