[Guide] TWRP with Magisk on 10.0.4.0 Stock ROM - Xiaomi Mi A2 Lite Guides, News, & Discussion

GSI IS DONE CHECK THE LINK BELOW, IT'S CURRENTLY IN PROGRESS BELOW IS THE STATUS ME WORKING ON IT
THE GSI PIE TUTORIAL
Grab these two files (Big Thanks to @Zerovoid from 4PDA, @Seryioo, and @mac12m99)
Fixed SDCard Support TWRP Image File (Download this and put this on your SDCard and Computer)-
Original Fixed TWRP XDA Post
Fixed SDCard Support TWRP Installer Zip (Download and put this on your SDCard)-
Fixed TWRP .zip Installer
But I got TWRP on 10.0.4.0 with magisk, and Justice Kernel.
THIS WILL WIPE YOUR DEVICE I'M DEFINITELY NOT RESPONSIBLE FOR LOST DATA, SD CARDS, ETC
Start with the phone being on with USB Debugging enabled correctly and bootloader unlocked
Type: adb reboot bootloader
So flash the 10.0.4.0 ROM through MiFlash using the flash_all.bat, this process has to be done so backup your data before erasing.
After it is done flashing it restarts, go ahead and hold power and volume down right back to the Bootloader
Type: fastboot boot twrp-3.2.3-0-daisy_zero.img
It would boot into TWRP, if you see something about decryption hit cancel this may mean you haven't followed directions so far
Tap install and find your SD Card, find the fixed-twrp-installer-daisy.zip where ever you put it on your SD Card and install it, this process takes a few minutes when finished DO NOT HIT REBOOT SYSTEM!
Hit the home button back to TWRP home screen and tap reboot >>> bootloader
Download this to your computer -
aboot.img
Type: fastboot flash aboot aboot_9.6.4.img
Then type: fastboot reboot
Afterwards your phone shall boot up to Android if it does hold power and volume up and release power and keep hold volume up when the screen turns back on to go-to recovery, if TWRP boots up you have successfully completed the task.
Now flash Magisk zip (optional)
Hopefully this helped kind of my first tutorial, this was my process.

Reserved

Looks like I'll be updating and trying when I get home wish me luck..

rob420p said:
Looks like I'll be updating and trying when I get home wish me luck..
Click to expand...
Click to collapse
I'll have the GSI Tutorial up as soon as possible. Let me know if you run into any problems!

I am curious does the backup n restore work with this?

rob420p said:
I am curious does the backup n restore work with this?
Click to expand...
Click to collapse
Everything in TWRP works sir, it was already functional the only component missing in the original is the SD Card Support which is fixed in the TWRP above!

But why this tutorial when wifi isn't working than. I think everyone needs wifi.
Sent from my Phh-Treble vanilla using Tapatalk

cd492 said:
But why this tutorial when wifi isn't working than. I think everyone needs wifi.
Click to expand...
Click to collapse
From what I have read this is happening to allot of devices running pie not just our device

cd492 said:
But why this tutorial when wifi isn't working than. I think everyone needs wifi.
Sent from my Phh-Treble vanilla using Tapatalk
Click to expand...
Click to collapse
That's weird, I'm running Android Pie on A2L and Wi-Fi looks great.
Have you tried performing a full wipe and flashing the stock ROM?
I had other issues which were fixed by flashing the stock ROM with a full wipe.
Tbh I don't think the patch updates are 100% trustworthy, so I simply update it manually.

cd492 said:
But why this tutorial when wifi isn't working than. I think everyone needs wifi.
Sent from my Phh-Treble vanilla using Tapatalk
Click to expand...
Click to collapse
lbsilva said:
That's weird, I'm running Android Pie on A2L and Wi-Fi looks great.
Have you tried performing a full wipe and flashing the stock ROM?
I had other issues which were fixed by flashing the stock ROM with a full wipe.
Tbh I don't think the patch updates are 100% trustworthy, so I simply update it manually.
Click to expand...
Click to collapse
This does not relate to this tutorial, there is nothing wrong with WiFi from this tutorial
I was talking about the GSI Tutorial I am making in the cyan text above nothing it wrong with this tutorial, if there was why would I post it

rob420p said:
Looks like I'll be updating and trying when I get home wish me luck..
Click to expand...
Click to collapse
Have you tested it?

InfinityXDA said:
Have you tested it?
Click to expand...
Click to collapse
Not yet I'm useing a new laptop and had trouble sitting up my cdrive I'll try again tonight

rob420p said:
Not yet I'm useing a new laptop and had trouble sitting up my cdrive I'll try again tonight
Click to expand...
Click to collapse
If you need assistance just let me know!

InfinityXDA said:
If you need assistance just let me know!
Click to expand...
Click to collapse
I main issue I was having was with mi flash for some reason when I check the Oreo Ron I can't find it in the files downloaded 5 times

rob420p said:
I main issue I was having was with mi flash for some reason when I check the Oreo Ron I can't find it in the files downloaded 5 times
Click to expand...
Click to collapse
You have to extract the file using WinZip, it's just like a .zip file. But after you extract the stock rom there should be another file in that extract that too and select the folder extracted folder with all of the .img in it in MiFlash.
You must have the Pie ROM to do this
Please make sure you have the latest ROM or latest patch from this link https://en.miui.com/getrom-354.html?

InfinityXDA said:
You have to extract the file using WinZip, it's just like a .zip file. But after you extract the stock rom there should be another file in that extract that too and select the folder extracted folder with all of the .img in it in MiFlash.
You must have the Pie ROM to do this
Please make sure you have the latest ROM or latest patch from this link https://en.miui.com/getrom-354.html?
Click to expand...
Click to collapse
Thanks this is a little different I'm used to Nexus or motorola devuces

rob420p said:
Thanks this is a little different I'm used to Nexus or motorola devuces
Click to expand...
Click to collapse
No problem I'm here to help!

Thanks for the nice Tutorial, the installation works fine.
Backup to the sd-card is now possible, but the restore doesn' work. It stops with this message:
Cannot restore System -- mounted read only

Linhx said:
Thanks for the nice Tutorial, the installation works fine.
Backup to the sd-card is now possible, but the restore doesn' work. It stops with this message:
Cannot restore System -- mounted read only
Click to expand...
Click to collapse
So it's not mounting right sounds like it can right but can't read

I found the solution here:
https://forum.hovatek.com/thread-15952.html
- Go to the TWRP Home Screen and select Mount
- Untick "Mount system partition read-only"
Restore was starting then, but after 99% this error appeared:
The extractTarFork() process ended with ERROR: 255
The device didn't start anymore and I had to set it up again.

Related

[Recovery][G925P] TWRP 2.8.7.0 Touch Recovery UPDATED FOR 5.1.1!!!! [2015-7-16]

Well it's here everyone TWRP for 5.1.1. Yes this works for 5.0.2 also. Works on OFE, OF7, OH1, OI1, OJ7 and OL1 5.1.1
TWRP for Marshmallow go Here
All credit goes to @ram9200 so be sure to thank him for the numerous hours of hard work to get this working
Instructions for 5.1.1:
In order for this to work on 5.1.1, first enable OEM unlocking under developer options, then you must head on over to @djvoleur thread and install his rooted kernel first.
Link: Here
then proceed to the next steps.
This is rare but if for some reason you get stuck in recovery or your recovery doesn't boot properly, then you may need to do a factory reset or wipe your internal partition.
How to Install:
Using odin:
Download and install the drivers
Download the tar file
Download Odin 3.10.6 or 3.10.7, extract then install
Leave Auto reboot and F. Reset Time checked
Absolutely do not check repartition
Click AP/PDA
Navigate to the recovery.tar
Hold down power + volume down + home on your phone to enter download mode and connect via USB cable
Click Start
Hold down the power, home, and volume up button when it reboots
Rinse and repeat if TWRP does not install
Using Flashify:
Download Flashify from Google Play
Download the img file
Under the FLASH tab using the Flashify app click Recovery Image.
Find the img file you just downloaded..
Click on the img file then you will be prompted with a Flash Recovery? screen.
Click YUP if you would like to continue with the flash or MAYBE NOT... if you chose the wrong file or have changed your mind.
If you chose to continue flashing you will see a working box which says Flashing...
A box which says Flash Completed will show after flash is complete.
Click Reboot Now.
Done!
Happy Flashing!!
Worked fine for me but:
FLASH AT YOUR OWN RISK
Download Links:
Tar File
img File
Next, if you need a custom Rom with support, you might want to check one of these out.
Renegade Rom Here
Joshwaa's Rom Here
Wicked One Rom Here
Uff it works perfectly thanks!!!!
Install a theme and the Chinese text is gone!
I grabbed one from HERE
Boots fine, touch screen works fine. Haven't tried backup and restore yet.
adb works just fine too. Can push and pull files while in recovery now !!!
fgr said:
Install a theme and the Chinese text is gone!
I grabbed one from HERE
Boots fine, touch screen works fine. Haven't tried backup and restore yet.
adb works just fine too. Can push and pull files while in recovery now !!!
Click to expand...
Click to collapse
Can you tell me which theme you used exactly? Having a hard time navigating that thread
fgr said:
Install a theme and the Chinese text is gone!
I grabbed one from HERE
Boots fine, touch screen works fine. Haven't tried backup and restore yet.
adb works just fine too. Can push and pull files while in recovery now !!!
Click to expand...
Click to collapse
Cool thanks, that fixed the text issue. I'll update the OP!
SantinoInc said:
Can you tell me which theme you used exactly? Having a hard time navigating that thread
Click to expand...
Click to collapse
Any.........I used the material black. Go to the very beginning of the thread and read the instructions on how to apply.
Basically just choose the proper resolution and change the name to ui.zip and create the appropriately named folder?
Also, I'm paranoid about the Chinese text on the first boot up. I know REBOOT option is bottom right. On the next screen where is the SYSTEM REBOOT button?
Thanks a million for posting this and thanks for the help!
SantinoInc said:
Basically just choose the proper resolution and change the name to ui.zip and create the appropriately named folder?
Also, I'm paranoid about the Chinese text on the first boot up. I know REBOOT option is bottom right. On the next screen where is the SYSTEM REBOOT button?
Thanks a million for posting this and thanks for the help!
Click to expand...
Click to collapse
lol no problem, on the next screen system is the top left button
Ok, so I got the TWRP flashed with Flashify, held my breath and it worked!
I created a folder called "theme" and placed a theme of my liking in the folder under the name "ui.zip" Will the theme automatically load when I boot into recovery or will I have to so some Chinese text navigating? Can you take me through the clicks if I have to go through the Chinese text?
Also, do you know if this TWRP will bring the deep sleep problems that plagued early rooted users?
Just picked up my edge today! Going to get this installed once I am home. Looking forward to a custom ROM in the near future (hopefully!).
SantinoInc said:
Ok, so I got the TWRP flashed with Flashify, held my breath and it worked!
I created a folder called "theme" and placed a theme of my liking in the folder under the name "ui.zip" Will the theme automatically load when I boot into recovery or will I have to so some Chinese text navigating? Can you take me through the clicks if I have to go through the Chinese text?
Also, do you know if this TWRP will bring the deep sleep problems that plagued early rooted users?
Click to expand...
Click to collapse
Once you create the folder and place the theme there, all you have to do is boot into recovery and all Chinese is gone. Not sure if the deep sleep issue is present. Hopefully someone will report back. I was able to successfully create a backup and was able to flash some themed apps.
Soooperstar said:
Not sure if the deep sleep issue is present.
Click to expand...
Click to collapse
Crap!!! No deep sleep!!!
Flashing stock back. Oh well, easy enough to swap back and forth between twrp and stock. I'll just flash twrp when I need to use it for some reason.
fgr said:
Crap!!! No deep sleep!!!
Flashing stock back. Oh well, easy enough to swap back and forth between twrp and stock. I'll just flash twrp when I need to use it for some reason.
Click to expand...
Click to collapse
You can give this zip fix a try.
http://zidroid.com/fix-battery-drain-and-deep-sleep-issue-on-galaxy-s6-and-s6-edge/
Soooperstar said:
You can give this zip fix a try.
http://zidroid.com/fix-battery-drain-and-deep-sleep-issue-on-galaxy-s6-and-s6-edge/
Click to expand...
Click to collapse
Flashed twrp, flashed deep sleep fix, deep sleep is back! Thanks for the tip!
if anyone wants to make a backup of twrp with the theme and deep sleep already flashed that would be amazing! for some reason from the op i cant get an img file from the dl link : (
im really interested if we can streamline the process and have a single img file we can get a stable working twrp
TookRDerbs said:
if anyone wants to make a backup of twrp with the theme and deep sleep already flashed that would be amazing! for some reason from the op i cant get an img file from the dl link : (
im really interested if we can streamline the process and have a single img file we can get a stable working twrp
Click to expand...
Click to collapse
My deep sleep always worked.
Try this one
https://www.dropbox.com/s/5tmpxzk2kh1pwtf/G9250-TWRP-2.8.6.0-CN(0421).zip?dl=0
I think my deep sleep was working as well but just in case I did a backup and flashed the fix. Thanks for reviving this phone!
How do I know if deep sleep is working or not?
Other than that this is awesome!
Sent from my SM-G925P
blacksantron said:
How do I know if deep sleep is working or not?
Other than that this is awesome!
Sent from my SM-G925P
Click to expand...
Click to collapse
Download CPU Spy from the Playstore, run the app, let your screen sleep for about 5-10 mins, wake your phone and open the app, if you see a percentage under deep sleep then you're good, if you see nothing, then you need the fix
finally got odin to work with me and got twrp up and running! thanks everyone for the help and resources.
NOW its time to make a backup and try to start adding some goodies : ) and to mess around and see if i can get my rotation back lol

[RECOVERY] [F1f-Spectrum] [TWRP-3.1.1-0] For Project Spectrum Bootloader ONLY!

This is an unofficial port of TWRP Recovery for the Oppo F1F on Project Spectrum Bootloader. Much Thanks and credit goes to the TWRP team, Lineage team, and brinleyaus for making this possible. This will allow flashing of modification zips (eg. supersu, magisk, xposed, etc) over the top of Project Spectrum or flashing spectrum based ROMS.
Instructions:
Already running Project Spectrum
- If you haven't already unlocked you bootloader you will need to go into SETTINGS > ABOUT PHONE and tap BUILD NUMBER 7 times to unlock DEVELOPER OPTIONS, Then go into SETTINGS > DEVELOPER OPTIONS and enable them, also enable ADB DEBUGGING and OEM UNLOCK. Now reboot into fastboot (adb reboot bootloader) and run fastboot oem unlock.
- Install this image file through fastboot (If you are unsure of this step follow one of the many tutorials about installing TWRP through fastboot)
On ColourOs with TWRP
- Do a full wipe first or the install will fail. (In TWRP hit WIPE then swipe to factory reset.) Do a backup first as you will lose data.
- Flash this zip file through twrp and then hit "wipe dalvic and cache", then hit HOME then REBOOT then RECOVERY. (rebooting to the new recovery will ensure the recovery sticks) then Flash any Spectrum based rom or restore any Spectrum based backup. NOTE the ColorOs system and boot.img will still be there but wont boot so you MUST flash or restore a Spectrum based rom before you reboot to system.
Reserved.
MiniBlu said:
Reserved.
Click to expand...
Click to collapse
Battery can't charge full!! Help ?
Added file and instructions to OP to flash Spectum bootloader,firmware and twrp From ColorOs TWRP.
Thank.link from androidfilehost is slowly. I using wifi
Sent from my F1w using XDA-Developers Legacy app
MiniBlu said:
Added file and instructions to OP to flash Spectum bootloader,firmware and twrp From ColorOs TWRP.
Click to expand...
Click to collapse
The TWRP is not the 3.1.1
It is the 3.0.1
khannz7 said:
The TWRP is not the 3.1.1
It is the 3.0.1
Click to expand...
Click to collapse
Which file are you talking about, I just checked the links and the flashable zip was actually pointing to the full ROM which defiantly has the 3.1.1-0 version. (I just fixed the link to point at the bootloader, firmware and twrp zip.) Are you rebooting to recovery after flashing to make it stick?
MiniBlu said:
Which file are you talking about, I just checked the links and the flashable zip was actually pointing to the full ROM which defiantly has the 3.1.1-0 version. (I just fixed the link to point at the bootloader, firmware and twrp zip.) Are you rebooting to recovery after flashing to make it stick?
Click to expand...
Click to collapse
The PS 1
Yeah doing it right....But it is the same old twrp 3.0.1 mentioned somewhere in the G+ forums....
Never mind ....did you get the port to work
khannz7 said:
Yeah doing it right....But it is the same old twrp 3.0.1 mentioned somewhere in the G+ forums....
Never mind ....did you get the port to work
Click to expand...
Click to collapse
Which ps1 g or zip?
I have just checked. None of the files I have posted are the old version. They are all the newest 3.1.1-0 version.
No not yet.
MiniBlu said:
I have just checked. None of the files I have posted are the old version. They are all the newest 3.1.1-0 version.
No not yet.
Click to expand...
Click to collapse
I have installed the full ps rom with twrp but what I got is not 3.1.1 it is the 3.0.1
+
Maybe I could help you somewhere with the port
I have to remove the sd card and then re-insert it then it received. who can solve it? The battery will charge too long to fill up
khannz7 said:
I have installed the full ps rom with twrp but what I got is not 3.1.1 it is the 3.0.1
Click to expand...
Click to collapse
OK, I'll download it and check, maybe I uploaded from the old folder. Hope not 6.5 hours to upload it.
MiniBlu said:
OK, I'll download it and check, maybe I uploaded from the old folder. Hope not 6.5 hours to upload it.
Click to expand...
Click to collapse
I would love to help you with the port and maybe I could get something new to learn:fingers-crossed:
Phucan2017 said:
I have to remove the sd card and then re-insert it then it received. who can solve it? The battery will charge too long to fill up
Click to expand...
Click to collapse
No one. If you don't like it stick with ColorOs or Lineage.
khannz7 said:
I would love to help you with the port and maybe I could get something new to learn:fingers-crossed:
Click to expand...
Click to collapse
Not just yet, just got to work out the ramdisk changes needed to get ported roms to boot properly with spectrum kernel, then I'll share the info with you and then let the porting begin.
MiniBlu said:
No one. If you don't like it stick with ColorOs or Lineage.
Not just yet, just got to work out the ramdisk changes needed to get ported roms to boot properly with spectrum kernel, then I'll share the info with you and then let the porting begin.
Click to expand...
Click to collapse
Cool
I did that. But for oppo f1 this rom is not finished yet but there are still many bugs. I return coloros
Just used the spectrum zip and worked flawlessly.(from other thread oops) Thanks alot.
How to go back to coloros ? Do i need to flash stock recovery ?
Sent from my F1f using XDA Labs
the_reds2000 said:
How to go back to coloros ? Do i need to flash stock recovery ?
Sent from my F1f using XDA Labs
Click to expand...
Click to collapse
No, Read the OP of this thread. There is a zip (and instructions) to return to ColorOs Bootloader,firmware and TWRP. From there you can flash any TWRP flashable ColourOs based Rom (ColorOs or LineageOS) or restore backups from them.
Which root method will be used for this?

[Tool][Unbrick][Reset][Fix for bad Signal] Stock Firmware

Unbrick tool by One-Team - EypCnn
First: This tool seems to be from EypCnn, One-Team. All credits to them!
EDIT2: I no longer own this device, so i will leave this thread here for people to use. But don't expect any direct support from me .
What can this tool do?:
Restore phone to Stock(International) Firmware (S048) Marshmallow (Locked & Unlocked bootloader)
Fix Lost or bad Signal / IMEI any software Problem
For who does this work?
Pretty much any Lenovo P2 Variant (Chinese and International)
Phones which can access bootloader(you have to boot into it)
Works on Locked & Unlocked Bootloader
Installation aka. Flashing-Steps
Put your phone into bootloader (which is also fastboot) mode.
Download the folder and unzip it.
Connect your phone to your pc.
Go into the unzipped folder and open "flashall - stock reco.bat"
Wait, for the process to end, your phone will reboot on its own.! A stock lenovo bootlogo will show up !
You can disconnect your phone cable from pc and plug into a wall charger, just to be safe. Once the lockscreen is showing up, you're done.
If you want to flash Custom Roms:
look below:
WHEN MOVING TO CUSTOM ROMS NOW:
1. Boot to twrp. (Make sure it is pietwrp from telegram or the official 3.2.3 or later version)
2. Select WIPE menu option
3. Select data partition
4. Change file format to f2fs or anyother.
5. Go back to Start Menu of TWRP, choose Reboot Menu Option
6.Reboot to Recovery
7. Repeat Steps 2 and 3
8. This time select EXT4 when changing file format
9. Do Step 5 and 6
10. Wipe System,Cache and Dalvik-Cache partitions
( for older twrp versions: 10.1 If you're on official twrp 3.2.3 or lower, you have to flash pietwrp or latest twrp now !)
11. Flash your Custom Rom, Gapps (optional) and latest Magisk(optional)
12. Wipe Cache and Dalvik-Cache
13. Reboot. First Boot might take a few minutes but never longer than 7minutes.
If it takes longer, you're encounter a so called bootloop.
Comment hear if that happens, containing information on your twrp-version, rom, gapps, magisk and mods(if present) you're using.
When you corrupt your internal Storage or geht TWRP Error 1001, Error 7:
1. Repeat steps 2-6
2. Repeat steps 7-8
Download(Official Link)
2nd Link(reuploaded because some couldn't download it from androidfilehost): https://drive.google.com/open?id=1wUOZiTwW8mo0IheAGONyj9-QnjimnY2M
I will help if questions arise.
Credits to One-Team & EypCnn.
Thanks a lot. You literally saved my life!
Works like Magic
Thanks a lot for saving my ass . simplest way to downgrade to mm too. Thanks again
Wait.... downgrade to MM? Does this mean you can regain your signal or did @krishnakoonala get it wrong?
I have a spare P2 lying around that I never used because the IMEI got corrupted and I couldn't flash the bootloader files since I was unlocked.
I assume this wouldn't solve my issue?
eried1 said:
Wait.... downgrade to MM? Does this mean you can regain your signal or did @krishnakoonala get it wrong?
I have a spare P2 lying around that I never used because the IMEI got corrupted and I couldn't flash the bootloader files since I was unlocked.
I assume this wouldn't solve my issue?
Click to expand...
Click to collapse
My p2 was bricked and , stuck in boot loop. I followed the above instructions, 10 mins into it , it booted with mm version, the same version when i bought and booted for 1st time. It was like a new phone to me.
So i assume if one has upgraded to noughat and want to downgrade but is worried he might brick his device, one can take a back up and try this tool. It works flawless.
No harm in trying this one if ur p2 can boot up mate. Give it a shot. Good luck
Cheers
This tool has saved my device from multiple over a span of two years soft bricks. Can confirm it to do wonders.
eried1 said:
Wait.... downgrade to MM? Does this mean you can regain your signal or did @krishnakoonala get it wrong?
I have a spare P2 lying around that I never used because the IMEI got corrupted and I couldn't flash the bootloader files since I was unlocked.
I assume this wouldn't solve my issue?
Click to expand...
Click to collapse
THis will solve your problem , Cheers.
I tried but cannot download it - do you where to find it?
can i flash this without pc?? if yes please tell how
@sm00th4f3 bro, i wanna know, does this tool flashes full ROM including modem files etc, even on unlocked bootloader?
What is the state of bootloader after using this tool?
amansehdav said:
@sm00th4f3 bro, i wanna know, does this tool flashes full ROM including modem files etc, even on unlocked bootloader?
What is the state of bootloader after using this tool?
Click to expand...
Click to collapse
It flashed everything you have when you buy a new phone. And no, it doesn't lock your bootloader.
So you can either :
- keep using MM Stock Rom S048
- Update via ota in System like you normally would do.
- Update till latest Firmware, then flash twrp- and then Custom Rom of your Choice.
Bootloader is in the same state it was before you used this tool.
sm00th4f3 said:
It flashed everything you have when you buy a new phone. And no, it doesn't lock your bootloader.
So you can either :
- keep using MM Stock Rom S048
- Update via ota in System like you normally would do.
- Update till latest Firmware, then flash twrp- and then Custom Rom of your Choice.
Bootloader is in the same state it was before you used this tool.
Click to expand...
Click to collapse
So how does it fixes corrupted modems? it cannot be flashed on unlocked P2 right?
amansehdav said:
So how does it fixes corrupted modems? it cannot be flashed on unlocked P2 right?
Click to expand...
Click to collapse
I literally just answered it above somewhere.
(Literally in thread description)
You can flash it on unlocked bootloader or locked as well.
So many thanks for bringing up tis tool for us!
This thread should be stick as the "New user" thread is, they definitely belong together.
Download source
Thanks guys, if this works I can now revive my phone. But can someone please upload the tool to another place like google drive. From android filehost it will take an eternity to download!
HkQc said:
So many thanks for bringing up tis tool for us!
This thread should be stick as the "New user" thread is, they definitely belong together.
Click to expand...
Click to collapse
I didn't bring it up, i just linked it . All Credits belong to ONE TEAM and EypCnn.
ryd3r89 said:
Thanks guys, if this works I can now revive my phone. But can someone please upload the tool to another place like google drive. From android filehost it will take an eternity to download!
Click to expand...
Click to collapse
Link updated, Cheers
Lavesh05 said:
can i flash this without pc?? if yes please tell how
Click to expand...
Click to collapse
Nah you need a Computer for this.
no signal after using "flashall - stock reco.bat", it finished successfully, but after rom setup still no signal
GPSSlovakia said:
no signal after using "flashall - stock reco.bat", it finished successfully, but after rom setup still no signal
Click to expand...
Click to collapse
If you used some other tool for imei. You are pretty much done for.
Using this tool i can go to MM version and can upgrade to S251. However after installing twrp and flashing custom rom, it goes to bootloader

[hisense a6] custom reupload - R 02 (HLTE700T-L1488.6.09.02.00)

I made hisense a6 custom rom with yklaxds 's qpst package.
I merge system.img and modified rawprogram
i install gapps manually.
set security label and permission.
most function work very well.
ota update impossible. because of hisense's update is bonding partition
qualcomm package open now.
R02 HLTE700T-L1488.6.09.02.00.joygram
https://drive.google.com/file/d/1mgpOIClF0fgIkPc5rMth6VtNa0mJKG9z/view?usp=drivesdk
link may be block because heavy traffic by onedrive.
backup and share please.
R01 HLTE700T_L1488.6.04.01.00.joygram
https://1drv.ms/u/s!As0qoPp2K9MuaQeKFk-6PrnqfZ4
(onedrive blocked because heavy traffic, backup and share, please)
flashing method
https://1drv.ms/b/s!As0qoPp2K9MuaHBVpNnNPGkKl2M
nitice:
please use
rawprogram_30060000_joygram.xml only.
notice:
if appear password screen after flashing.
enter recover mode and factory reset
recovery mode :
power off : power button about 20 seconds over
volume_down + power : about 5 seconds and remove your fingers^^
notice:
WIP custom with L1488.6.09.02.00
if you brick, use TF recovery ROM
Link: https://pan.baidu.com/s/1Mkjvb9q_0oGuXZ0KLprJog extraction
code: j8qi
you can recover.
this instruction from official hisense forumn
2) Preparation before the T card upgrade:
1. Prepare a TF card and format the TF card into FAT format first;
2. Decompress the downloaded product software version (generally a compressed package and divide it into multiple compressed sub-packets) and copy the obtained folder named "HLTE700T_TF" to the root directory of the TF card.
3. Insert the TF card into your phone and put the battery in your phone. Make sure the battery is more than 50% charged. If the battery is low, please charge it first.
(three) T card upgrade process
1. Press and hold the “Volume+” and “Volume-” side buttons at the same time, then press the power button, the phone will automatically enter the T card upgrade mode for upgrade. If the phone does not enter the T card upgrade mode, please shut down. Repeat this operation.
2. Wait for about 5 minutes to complete the upgrade and a prompt for the upgrade to be successful.
3. Restart according to the prompt after successful upgrade. If there is no such prompt, press and hold the power button for more than 20 seconds to restart. After the upgrade, the first boot time is longer, which is several times of the normal boot time. Please be patient.
**
I am not chinese but korean
Thanks very much,
root the phone did you have method?
Maybe you can share your ways that how do you make it to let more people to discuss it. Thanks.
I will upload latest version QPST ROM, also from taobao.com. Please wait for me.
------------------------------------------------------------------------------------------------------------------
2019 5.16 version L1488.6.09.02.00 official ROM QPST:
https://drive.google.com/file/d/1IOxo79igLjPoldLmbP7eEM0W7UQpS3P-/view?usp=sharing
sdwshlsdx said:
Thanks very much,
root the phone did you have method?
Click to expand...
Click to collapse
Just add su file or root app like SuperSU? I dont know. Maybe have a try. You can just extract my ROM file(system.img files).
yklaxds said:
Maybe you can share your ways that how do you make it to let more people to discuss it. Thanks.
I will upload latest version QPST ROM, also from taobao.com. Please wait for me.
------------------------------------------------------------------------------------------------------------------
2019 5.16 version L1488.6.09.02.00 official ROM QPST:
https://drive.google.com/file/d/1IOxo79igLjPoldLmbP7eEM0W7UQpS3P-/view?usp=sharing
Click to expand...
Click to collapse
I will research more.
Thank you.
I flashed it according to your method. But now it's asking for password. How to proceed?
danjl said:
I flashed it according to your method. But now it's asking for password. How to proceed?
Click to expand...
Click to collapse
may be all partition not flashed.
check rawprogramming _joygeam.xml
if comment any partition with <!-- -->
remove this
i will check firmware and release soon
i am sorry for inconvenience
pengboby126 said:
Thanks a lot for this rom?
Is it possible to enable camera 2 api by modifying build.prop, which functions Gcam Port?
Click to expand...
Click to collapse
i tried but no gapps cam working.
if you know gcam for hisense a6
let me know.
joygram said:
may be all partition not flashed.
check rawprogramming _joygeam.xml
if comment any partition with <!-- -->
remove this
i will check firmware and release soon
i am sorry for inconvenience
Click to expand...
Click to collapse
How can I reset phone? It's not detected through usb anymore
danjl said:
How can I reset phone? It's not detected through usb anymore
Click to expand...
Click to collapse
dont worry.
you can recover with hisense TF Rom from fans.hisense.com ( hisense forum)
download tf rom and flashing.
I have files but can release next weekend.
sdwshlsdx said:
Thanks very much,
root the phone did you have method?
Click to expand...
Click to collapse
i am researching method with recovery.
joygram said:
may be all partition not flashed.
check rawprogramming _joygeam.xml
if comment any partition with <!-- -->
remove this
i will check firmware and release soon
i am sorry for inconvenience
Click to expand...
Click to collapse
joygram said:
dont worry.
you can recover with hisense TF Rom from fans.hisense.com ( hisense forum)
download tf rom and flashing.
I have files but can release next weekend.
Click to expand...
Click to collapse
EDIT: Yipee! It was asking for password. I booted to recovery by Hodling volume down+power. Then select an option to erase data, confirm by pressing volume up. It took a few minutes.
Then it booted with the custom rom!
So, anyone who comes across password can just erase their phone by booting into recovery.
Thanks to joygram! This works, so looking forward to having gapps on my phone now! Good luck to everybody.
danjl said:
How can I reset phone? It's not detected through usb anymore
Click to expand...
Click to collapse
Please try my hisense official flashing ROM.
https://drive.google.com/file/d/1IOxo79igLjPoldLmbP7eEM0W7UQpS3P-/view
---------- Post added at 05:06 PM ---------- Previous post was at 05:03 PM ----------
joygram said:
i am researching method with recovery.
Click to expand...
Click to collapse
Yep, we need twrp so that we can root or flasing GAPPS.
danjl said:
EDIT: Yipee! It was asking for password. I booted to recovery by Hodling volume down+power. Then select an option to erase data, confirm by pressing volume up. It took a few minutes.
Then it booted with the custom rom!
So, anyone who comes across password can just erase their phone by booting into recovery.
Thanks to joygram! This works, so looking forward to having gapps on my phone now! Good luck to everybody.
Click to expand...
Click to collapse
enjoy !!
So to summarize... If we get chinese version of A6 we can now flash this custom rom to have both :
- gapp (not available on chinese version)
- Widgets and full eink function (not available on russian version)
?
Yep, we need twrp so that we can root or flasing GAPPS.[/QUOTE]
->
I can not make twrp
I just merge system.img and install gapps manually.
so I can not root
but I will try
I used Magisk and patched boot.img in joygram's ROM. Then I replaced the original boot.img with partched one, and then used the same method with QFIL. It works!
But when you boot it reminds you device state is locked. However, Magisk is fully operational and I have used many modules already.
danjl said:
I used Magisk and patched boot.img in joygram's ROM. Then I replaced the original boot.img with partched one, and then used the same method with QFIL. It works!
But when you boot it reminds you device state is locked. However, Magisk is fully operational and I have used many modules already.
Click to expand...
Click to collapse
How do you change it? I also want root. Just like this way?
https://juejin.im/post/5b1bb43b5188257d5903045b
I want to make twrp but I don't know how to do it. Here no ways to teache me.
And can we unlock bootloader by ROM?
danjl said:
I used Magisk and patched boot.img in joygram's ROM. Then I replaced the original boot.img with partched one, and then used the same method with QFIL. It works!
But when you boot it reminds you device state is locked. However, Magisk is fully operational and I have used many modules already.
Click to expand...
Click to collapse
could you please boot.img release?
joygram said:
could you please boot.img release?
Click to expand...
Click to collapse
I'll upload it soon. Having some troubles with internet connection.
Thanks for the roms you uploaded.

General [ROM] BlissfulROM

Downloads for Google Pixel 6a (bluejay)
downloads.blissroms.org
The official blissrom
How to flash?
Via fastboot clearly doesn't work,but i don't know where to find a working custom recovery for this phone
xUltramarco said:
How to flash?
Via fastboot clearly doesn't work,but i don't know where to find a working custom recovery for this phone
Click to expand...
Click to collapse
I used the recovery from Paranoid, the Pixel Flasher desktop app should work too.
ROM works great tho, my daily driver until QPR2 came out..
QPR2?
none of the recovery i tried worked,but i solved the problem extracting the payload.bin and after that created a zip with all the .imgs + a text file called "android-info.txt" with "require board=bluejay" inside,and then i flashed the zip via fastboot using "fastboot update -w NAMEOFTHEZIP.zip"
Anyone tryied this rom? Is working well?
charly30 said:
Anyone tryied this rom? Is working well?
Click to expand...
Click to collapse
I haven't even tried it yet. Been having internet problems where I live
xUltramarco said:
none of the recovery i tried worked,but i solved the problem extracting the payload.bin and after that created a zip with all the .imgs + a text file called "android-info.txt" with "require board=bluejay" inside,and then i flashed the zip via fastboot using "fastboot update -w NAMEOFTHEZIP.zip"
Click to expand...
Click to collapse
I'm about to try this. Will post what happens.
Download the crDroid ROM, pull recovery.img out of it, flash recovery, reboot recovery, then adb sideload this
There's a custom recovery in crdroid's zip
this is what I'm about to try
TechX1991 said:
Download the crDroid ROM, pull recovery.img out of it, flash recovery, reboot recovery, then adb sideload this
There's a custom recovery in crdroid's zip
this is what I'm about to try
Click to expand...
Click to collapse
Let me know if this works for you. I'm going to try all the ways people have explained to see which is easier and will make a post with directions later tonight or tomorrow. I will list user names for giving credit.
Theripper91 said:
Let me know if this works for you. I'm going to try all the ways people have explained to see which is easier and will make a post with directions later tonight or tomorrow. I will list user names for giving credit.
Click to expand...
Click to collapse
did not work for me with my idea above
I've always enjoyed blissrom, so i hope something works. i don't have time right now to try other ideas
TechX1991 said:
did not work for me with my idea above
I've always enjoyed blissrom, so i hope something works. i don't have time right now to try other ideas
Click to expand...
Click to collapse
I understand, tonight will be my time to try
charly30 said:
Anyone tryied this rom? Is working well?
Click to expand...
Click to collapse
It works just fine like stock,I know this is unrelated with Bliss but sadly viper4android on this device even with a custom ROM doesn't work (probably because of 32bit drivers of v4a) jamesdsp and Dolby Atmos works
xUltramarco said:
It works just fine like stock,I know this is unrelated with Bliss but sadly viper4android on this device even with a custom ROM doesn't work (probably because of 32bit drivers of v4a) jamesdsp and Dolby Atmos works
Click to expand...
Click to collapse
with the method i explained before
Follow the instructions on XDA for Raven. You will need the first time install zip. From my good drive. Profit.
stebomurkn420 said:
Follow the instructions on XDA for Raven. You will need the first time install zip. From my good drive. Profit.
Click to expand...
Click to collapse
Glad you could help with this. Time management has been crazy due to Christmas shopping. I'll mention you in the credits when I rewrite this post
xUltramarco said:
It works just fine like stock,I know this is unrelated with Bliss but sadly viper4android on this device even with a custom ROM doesn't work (probably because of 32bit drivers of v4a) jamesdsp and Dolby Atmos works
Click to expand...
Click to collapse
it has te same google camera? Can I enable motion mode? thank you
No,it doesn't include the stock google camera,and if you try to install the camera from the playstore it will crash when you try to open it.
Theripper91 said:
QPR2?
Click to expand...
Click to collapse
Android 13 QPR2 Beta 1

Categories

Resources