It's an improvement on the LiveView. It stays connected to my Note N7000, when I disconnect the Bluetooth it functions as a watch, I can also go into other rooms and the Bluetooth connection stays connected.
Sent from my Nexus 7 using Tapatalk 2
Hi guys,
can I connect my SW2 and Miband or any other fitness band at he same time, so it didn't disconnect from the Bluetooth?
Yeah. Simple lol
I've simultaneously connected SW2, Smartband, Headset (partly CarHifi) without any disconnects...
Von meinem Sony Xperia Z1 gesendet. Mit Hirn.
I use BT in my car on every drive, and am planning on getting a Gear S2 Classic (non-3G). I use an S7 Edge.
Are there any issues w/the S2 staying connected to my S7E when I'm in my car and connect to my car's BT system? Can my phone support both connections at the same time, or will I have to disconnect the Gear S2 to be able to connect to my car BT for music/phone?
Thanks!
There is no issue. Works fine for me.
Gesendet von meinem BLN-L21 mit Tapatalk
Redflea said:
I use BT in my car on every drive, and am planning on getting a Gear S2 Classic (non-3G). I use an S7 Edge.
Are there any issues w/the S2 staying connected to my S7E when I'm in my car and connect to my car's BT system? Can my phone support both connections at the same time, or will I have to disconnect the Gear S2 to be able to connect to my car BT for music/phone?
Thanks!
Click to expand...
Click to collapse
I haven't had any problems connecting both. My Note 4, Note 7 and S7E have all worked with my gear s2 and both cars and motorcycle helmet.
Sent from my SM-G935T using Tapatalk
They work but sometimes they hiccup and I might unpair the car and repair it, then they work fine
Since I have had my android device in the car,I have had troubles with my dab module. Now I received my second module. Connected it and the first impressions were fine. Then I stick the aerial to the windshield and it seems the problems aren't over.[emoji29] [emoji27] . Now I was just in my car and found out that the 12 v connection might be part of the problem, I connected it to a wire from the cigarette lighter and that's a switched 12v connection. I had the radio on with the key on acc (no running engine and no 12v on the lighter) reception was 3 bars. Then I switched the car on and reception was gone and the radio needed to reconnect to the usb module.... Maybe this is the source of the problem ?
Any ideas? I want to have it working all the time
Verstuurd vanaf mijn Z2 Pro met Tapatalk
Hi Guys. I have a problem with my bmw e46 and with the Erisin 5062 px5, when the radio is in operation, the sound goes off in the back right and front left after 10-15 minutes. Does anyone have any idea of what it can do? The other two speakers work without problems. Sorry for the Bad English
Gesendet von meinem SM-G950F mit Tapatalk
Sounds heat related, possibly dry solder joints at the amplifier chip? Does it come back on after a reset or when its cooled down?
Yes, exactly when the radio cools down then it works again for a while. But it would be worse today, it starts shortly after the radio start to beep and the sound falls completely off. How can I find out if it is on a solder joint on the chip?
Gesendet von meinem SM-G950F mit Tapatalk
You will need to visually inspect the main board, the amplifier chip will be soldered to the board and screwed the radio's chassis or heatsink.
Google dry joint so you know what to look for.
I removed the radio and looked at everything, it's nothing to see. Have the radio then about 30min on the 12V charger to run without problems. As soon as it was installed in the car, the beeping sounded again.
Gesendet von meinem SM-G950F mit Tapatalk
Small update, I have soldered the solder joints but it brings no improvement. The chip gets extremely hot and Dan goes away the sound. I think it's up to the chip but can not tell which is installed that is not a number or the like on it
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Gesendet von meinem SM-G950F mit Tapatalk
Should be fine to replace with tda7851
Mickygnt said:
Should be fine to replace with tda7851
Click to expand...
Click to collapse
In the radio is not the tda7851 but the tda7388 installed
Gesendet von meinem SM-G950F mit Tapatalk
Have now installed in the radio a new amplifier. The problem is still there. Does anyone have any idea what I could do?
Gesendet von meinem SM-G950F mit Tapatalk
bughubi said:
Have now installed in the radio a new amplifier. The problem is still there. Does anyone have any idea what I could do?
Gesendet von meinem rotary dial phone mit Tapatalk
Click to expand...
Click to collapse
See a professional installer to resolve the wiring problem, could that be something you do?
A friend of mine is a computer specialist and knows so very well, he could not notice anything. The chip gets too hot, if I cool down the chip with spray the sound works normally again until it gets hot again
Gesendet von meinem SM-G950F mit Tapatalk
I have the same problem , i still trying to find the solution. Please check my post. What is your device and MCU version?
bughubi said:
I removed the radio and looked at everything, it's nothing to see. Have the radio then about 30min on the 12V charger to run without problems. As soon as it was installed in the car, the beeping sounded again.
Gesendet von meinem SM-G950F mit Tapatalk
Click to expand...
Click to collapse
So the problem is probably not in the radio, possibly one (or more) of your speakers (or the wires to it) is broken.
Use a ohm meter to measure for a shortcut in the speaker wires. Or disconnect all speakers and try, after this try to connect the speakers one by one (difficult with the ISO connector, best to do with an intermediate wire with two ISO plugs) this way you can find the defective speaker / wires.