Good day gurus please help me out with this my infinix x551 16+1 the phone was on xui lollipop before i flashed a cm 13 custom rom, the phone started behaving abnormally, the phone went totally dead not charging not going to recovery just dead.
I tried to Flash the stock rom and it gave me boot error,
Error21002.00 pls help me out
I have used nck, spflashtool, cm2 mtk and miracle box all was to no avail.
Related
hi . i have an Allview x2soul ( a rebranded gionee elife s5.5) and since a week ago i am facing random reboot problems. when i am in recovery (twrp 2.8.6) the device is not rebooting , is working normaly but when it fully boots it is restarting imediatly or after few minutes . i"ve tried flashing another custom rom but no succes , i"ve used battery calibration but without succes. today i"ve flashed the stock rom from gionee s5.5 kk , and as üsual" it rebooted but i"ve seen something strange . the phone was plugged and the charging screen popped up showing low battery (it was the screen from the original rom) after that the battery screen from gionee popped up showing 68 % battery and after that it booted into system . now [email protected] flashed a custom rom ported by me ( pussyfap v4 beast edition mt 6592 ) and the reboots are a bit fewer than the reboots from the gionee rom . any advice ? i don"t think that the battery is dead because in twrp is doing just fine . thanks in advance
Hi,
Try posting your question here:
Android Q&A, Help & Troubleshooting
The experts there may be able to help.
Good luck!
Hi All,
This is my first post, so take it easy on me pls..
I need help flashing a hard bricked phone.
The phone wont turn on and when i flash a rom, after
20-55 seconds with a 100% red bar i get a brom error 4032.
I have a Jiayu S3 Advanced mtk6752 shipped with kitkat
And i flashed a android 5.0 stock rom with sp flash tool.
After not using for a while and replacing a cracked screen. My phone restarts itself and it was soft bricked.
Then i flashed the wrong rom it was a rom for Jiayu S3+ mtk6753 and now its hard bricked. I did everything i can find on the internet except making a jumper on the motherboard. Please help.
Let me explain what exactly happended.
I bought the china phone and on the first day that i got it i flashed a android lollipop 5.0 stock rom with sp flash tool. After that i used it for a month or so. Then i cracked the screen and the screen wasnt responding. After 3 months not using the phone i ordered a new screen with lcd and i replaced it.
I used the phone for 2 days and suddenly the phone restarts itself when i was playing music. After restart i was stuck on the logo. After restarting the phone again it was again stuck at the logo.
I tried to flash my phone again, but used the wrong rom.
It was a Jiayu S3+ mtk 6753 android 5.1 lollipop stock rom. I tried everything reinstalling drivers with usbdeview and device manager. Tried flashing different. Stock roms. Tried different key combinations. Sp flash works and can see the phone when flashing a rom but stops after 20-55 seconds with a 100% red bar and a brom error 4032 pops up. I saw on the interwebs that i make a jumper on my motherboard but i cant find lcolo or something like that. Please help..
Thank you in advance
Hi All,
This is my first post, so take it easy on me pls..
I need help flashing a hard bricked phone.
The phone wont turn on and when i flash a rom, after
20-55 seconds with a 100% red bar i get a brom error 4032.
I have a Jiayu S3 Advanced mtk6752 shipped with kitkat
And i flashed a android 5.0 stock rom with sp flash tool.
After not using for a while and replacing a cracked screen. My phone restarts itself and it was soft bricked.
Then i flashed the wrong rom it was a rom for Jiayu S3+ mtk6753 and now its hard bricked. I did everything i can find on the internet except making a jumper on the motherboard. Please help.
Let me explain what exactly happended.
I bought the china phone and on the first day that i got it i flashed a android lollipop 5.0 stock rom with sp flash tool. After that i used it for a month or so. Then i cracked the screen and the screen wasnt responding. After 3 months not using the phone i ordered a new screen with lcd and i replaced it.
I used the phone for 2 days and suddenly the phone restarts itself when i was playing music. After restart i was stuck on the logo. After restarting the phone again it was again stuck at the logo.
I tried to flash my phone again, but used the wrong rom.
It was a Jiayu S3+ mtk 6753 android 5.1 lollipop stock rom. I tried everything reinstalling drivers with usbdeview and device manager. Tried flashing different. Stock roms. Tried different key combinations. Sp flash works and can see the phone when flashing a rom but stops after 20-55 seconds with a 100% red bar and a brom error 4032 pops up. I saw on the interwebs that i make a jumper on my motherboard but i cant find lcolo or something like that. Please help..
Thank you in advance
rudycroes said:
Hi All,
This is my first post, so take it easy on me pls..
I need help flashing a hard bricked phone.
The phone wont turn on and when i flash a rom, after
20-55 seconds with a 100% red bar i get a brom error 4032.
I have a Jiayu S3 Advanced mtk6752 shipped with kitkat
And i flashed a android 5.0 stock rom with sp flash tool.
After not using for a while and replacing a cracked screen. My phone restarts itself and it was soft bricked.
Then i flashed the wrong rom it was a rom for Jiayu S3+ mtk6753 and now its hard bricked. I did everything i can find on the internet except making a jumper on the motherboard. Please help.
Let me explain what exactly happended.
I bought the china phone and on the first day that i got it i flashed a android lollipop 5.0 stock rom with sp flash tool. After that i used it for a month or so. Then i cracked the screen and the screen wasnt responding. After 3 months not using the phone i ordered a new screen with lcd and i replaced it.
I used the phone for 2 days and suddenly the phone restarts itself when i was playing music. After restart i was stuck on the logo. After restarting the phone again it was again stuck at the logo.
I tried to flash my phone again, but used the wrong rom.
It was a Jiayu S3+ mtk 6753 android 5.1 lollipop stock rom. I tried everything reinstalling drivers with usbdeview and device manager. Tried flashing different. Stock roms. Tried different key combinations. Sp flash works and can see the phone when flashing a rom but stops after 20-55 seconds with a 100% red bar and a brom error 4032 pops up. I saw on the interwebs that i make a jumper on my motherboard but i cant find lcolo or something like that. Please help..
Thank you in advance
Click to expand...
Click to collapse
Hello,
Please try posting your query here Ask any Query Newbie friendly with all relevant details, the experts there maybe able to assist you.
-Vatsal
I am trying to root my Infinix zero 2 running lollipop, I have tried almost every procedure buh I can't so need help
Me too
I need help i soft brick my phone and since then i have been unable to use it i have flash it with different rom it onlt display infinix logo and off again.
hello pls help me i bought a coolpad 8298-A01 working well with no issue so i tried to install gapps because it has none ..so i took google to get a twrp for it and i did not get any so i tried to port but got my device bricked after flashing device kept on rebooting ..now i search for the firmware online and i got it and try flashing it all Sp Flash Tool not working giving error ONLY v5.1532 that flashed it 100% but the device is not powering on nore even responding to charge only show red light when i connect to socket and system still detect it,,,please i need help
PHONE-COOLPAD_8298-A01
ANDROID VERSION - 5.1
CHIP -MT6735
RAM -2GB
ROM -8GB
THAKNS