Related
Hey Guys, bought my phone in Australia at retail. It's running 4.3 JB. I've already unlocked the bootloader and installed a recovery. Now I want to run KitKat. I checked and there's no OTA, it says I'm already up to date. I don't care about the dual sim at all as I only have one sim (it's actually quite annoying having two icons in the statusbar).
Can I just go and install any Moto G KitKat ROM onto the phone and it will work? Is it better to have the official OTA so that it updates the radios before installing a custom KitKat ROM? Do the radios matter? Will I brick my XT1033 if I install a ROM for XT1031, XT1032 etc. ?
Just asking before I kill the phone.
Thanks guys
Single SIM ROMs are not compatible with dual chip XT1033.
From what I have read there is only 2 options:
1. unlock the phone and load en.GB 4.3 ROM and wait for the 4.4 kitkat update on it
2. CM11 by dhacker29 - Read first post about the details about how to flash to XT1033 where you need to flash a modem as well. http://forum.xda-developers.com/showthread.php?t=2608377
Whatever you do, make sure you do a backup of the stock ROM as I don't see Australian ROM in the stock images thread yet. So if you need to go back you can safely restore. To Restore from CM11 you need to flash the old modem as well that is in the same thread.
There are no cases of bricking so far that I am aware of. Also you could try fastboot flashing* the en.GB 4.4.2 firmware.
http://forum.xda-developers.com/showpost.php?p=49861244&postcount=101
*mfastboot may be required.
EDIT: You should be aware that flashing the GB firmware also includes the GB Modem/Radio firmware. If you notice data/wifi/coverage issues after flashing, this may be the reason. There is currently on AU firmware image you can restore with.
Excluding the following commands should allow you to retain the AU Modem/Radio firmware:
flash modem NON-HLOS.bin
erase modemst1
erase modemst2
flash fsg fsg.mbn
syl0n said:
Single SIM ROMs are not compatible with dual chip XT1033.
From what I have read there is only 2 options:
1. unlock the phone and load en.GB 4.3 ROM and wait for the 4.4 kitkat update on it
2. CM11 by dhacker29 - Read first post about the details about how to flash to XT1033 where you need to flash a modem as well. http://forum.xda-developers.com/showthread.php?t=2608377
Whatever you do, make sure you do a backup of the stock ROM as I don't see Australian ROM in the stock images thread yet. So if you need to go back you can safely restore. To Restore from CM11 you need to flash the old modem as well that is in the same thread.
Click to expand...
Click to collapse
thats true, I flased cm11 and both sim signal not work,
then I flash modem xt1033 same not work again,
finally I restored my stock room and sit like a boss for waiting 4.4 officiall update,
my moto g from malaysia retailer. :angel:
invictussevenfold said:
thats true, I flased cm11 and both sim signal not work,
then I flash modem xt1033 same not work again,
finally I restored my stock room and sit like a boss for waiting 4.4 officiall update,
my moto g from malaysia retailer. :angel:
Click to expand...
Click to collapse
hi, do you manage to flash kitkat and get single sim to work?
devalian said:
hi, do you manage to flash kitkat and get single sim to work?
Click to expand...
Click to collapse
i did, with the following update OTA GB 4.4.2, but something wrong when flash using sideload or put zip file to sdcar, so it cant be done.
n today I want to change my moto to single sim, because I dont need dual sim acctually. keep calm developer
invictussevenfold said:
i did, with the following update OTA GB 4.4.2, but something wrong when flash using sideload or put zip file to sdcar, so it cant be done.
n today I want to change my moto to single sim, because I dont need dual sim acctually. keep calm developer
Click to expand...
Click to collapse
cool. i did tried a several methods, but i couldnt get the radio signal at all. so was wondering what did i did wrongly.
mind to elaborate more on your steps?
juzza87 said:
Hey Guys, bought my phone in Australia at retail. It's running 4.3 JB. I've already unlocked the bootloader and installed a recovery. Now I want to run KitKat. I checked and there's no OTA, it says I'm already up to date. I don't care about the dual sim at all as I only have one sim (it's actually quite annoying having two icons in the statusbar).
Can I just go and install any Moto G KitKat ROM onto the phone and it will work? Is it better to have the official OTA so that it updates the radios before installing a custom KitKat ROM? Do the radios matter? Will I brick my XT1033 if I install a ROM for XT1031, XT1032 etc. ?
Just asking before I kill the phone.
Thanks guys
Click to expand...
Click to collapse
I downloaded and uncompressed android 4.3 firmware - Blur_Version.14.71.8.falcon_umts.Retail.en.GB from http://sbf.droid-developers.org/phone.php?device=14
then ran the "flash-all.bat" script. Rebooted and then did the OTA update. A single (primary) sim works no issues, and my model number now says XT1032 instead of XT1033.
I'm sure you'd get the same result by just flashing straight Android 4.4.2 for Great Britain - Blur_Version.174.44.9.falcon_umts.Retail.en.GB
I only need one sim anyway, so it works well for me. then I make lots of modifications with Xposed.
gregneal said:
I downloaded and uncompressed android 4.3 firmware - Blur_Version.14.71.8.falcon_umts.Retail.en.GB from http://sbf.droid-developers.org/phone.php?device=14
then ran the "flash-all.bat" script. Rebooted and then did the OTA update. A single (primary) sim works no issues, and my model number now says XT1032 instead of XT1033.
I'm sure you'd get the same result by just flashing straight Android 4.4.2 for Great Britain - Blur_Version.174.44.9.falcon_umts.Retail.en.GB
I only need one sim anyway, so it works well for me. then I make lots of modifications with Xposed.
Click to expand...
Click to collapse
I am really curious so I'll try this. Downloading "Blur_Version.174.44.9.falcon_umts.Retail.en.GB" and will report back, worst case I just run the stock flash all again (Blur_Version.14.85.4.falcon_umtsds.AsiaRetail.en.03) now that I know there's no risk
juzza87 said:
I am really curious so I'll try this. Downloading "Blur_Version.174.44.9.falcon_umts.Retail.en.GB" and will report back, worst case I just run the stock flash all again (Blur_Version.14.85.4.falcon_umtsds.AsiaRetail.en.03) now that I know there's no risk
Click to expand...
Click to collapse
I used this guide http://forum.xda-developers.com/showthread.php?t=2542219
Changed the filenames for these commands to reflect the files in the folder:
mfastboot flash system system.img_sparsechunk1
to
mfastboot flash system system.img_sparsechunk.0
It is rebooting now.
Boot animations works [OK]
"Preparing Device - Please Wait..." [OK]
Choose Language (KK style!) [OK]
So far I only have one SIM card working with only one set of icons at the top and it has successfully connected to Vodafone AU (YES!)
Wifi network detected [OK]
OK everything is running! WiFi is working, phone is now running 4.4.2 KitKat! Just called myself and it worked!
THANKS GUYS
I will follow up later on. First thing I'll try is recovery, root, xposed framework and see if I can change the battery icon to show percentage (this wasn't possible on the JB ROM but I suspected because of the dual sim and likely a different SystemUI.apk
I had trouble rooting but then just used this flashable zip http://forum.xda-developers.com/showthread.php?t=2585755 and it got there.
I installed Xposed and everything worked as expected, using gravity box I changed the battery to one with a percentage and reduced the navigation bars to 70% (gives more screen real estate). Using the Google Experience Launcher, Google Keyboard and enabling ART has made this device a bit closer to my Nexus 4 which the screen broke on, so I'm very happy with this device.
Now I just need to work out how to get rid of the carrier name in the status bar (VODAFONE AU takes up a lot of room :silly
EDIT: Thanks Moto X community http://repo.xposed.info/module/com.penree.android.xposed.hidecarriermotox now it's gone
devalian said:
cool. i did tried a several methods, but i couldnt get the radio signal at all. so was wondering what did i did wrongly.
mind to elaborate more on your steps?
Click to expand...
Click to collapse
I think you should be waiting for general thread for moto G dual sim, and also they will create another rom for it.
I use Q10 now, bored with android :victory:
I flashed Google Play edition 4.4.2 ROM on my XT1033 + added Xposed GravityMod. Gives me 90% of what Cyanogenmod does so I am pretty happy.
syl0n said:
I flashed Google Play edition 4.4.2 ROM on my XT1033 + added Xposed GravityMod. Gives me 90% of what Cyanogenmod does so I am pretty happy.
Click to expand...
Click to collapse
Can you share some step by step instructions and links please?
Sent from my XT1033 using Tapatalk
occtec said:
Can you share some step by step instructions and links please?
Sent from my XT1033 using Tapatalk
Click to expand...
Click to collapse
try this.
http://forum.xda-developers.com/showthread.php?t=2635706
it works for me, changing XT1033 to single sim and kitkat.
1) download the file in the link
2) run the program and flash image with outside usa
3) flash cwm recovery
4) push superSU
5) install xposed framework with framework installer.
devalian said:
try this.
http://forum.xda-developers.com/showthread.php?t=2635706
it works for me, changing XT1033 to single sim and kitkat.
1) download the file in the link
2) run the program and flash image with outside usa
3) flash cwm recovery
4) push superSU
5) install xposed framework with framework installer.
Click to expand...
Click to collapse
Will give it a shot later, cheers mate. Just flat out with work atm. :banghead:
Sent from my XT1033 using Tapatalk
occtec said:
Can you share some step by step instructions and links please?
Sent from my XT1033 using Tapatalk
Click to expand...
Click to collapse
I used this: http://forum.xda-developers.com/showthread.php?t=2633272
Follow step by step instructions for International. Flash it all using fastboot. After the last step, before reboot, flash this GPE recovery: http://forum.xda-developers.com/showthread.php?t=2634008 (unzip it and run this command: fastboot flash recovery CWM6046-falcon_gpe.img)
Then I rebooted into the CWM recovery and used adb sideload to load to root it - follow this post exactly: http://forum.xda-developers.com/showpost.php?p=49996027&postcount=19
Once rooted installed Xposed and customise
syl0n said:
I used this: http://forum.xda-developers.com/showthread.php?t=2633272
Follow step by step instructions for International. Flash it all using fastboot. After the last step, before reboot, flash this GPE recovery: http://forum.xda-developers.com/showthread.php?t=2634008 (unzip it and run this command: fastboot flash recovery CWM6046-falcon_gpe.img)
Then I rebooted into the CWM recovery and used adb sideload to load to root it - follow this post exactly: http://forum.xda-developers.com/showpost.php?p=49996027&postcount=19
Once rooted installed Xposed and customise
Click to expand...
Click to collapse
How do you find the Play Edition compared to the Motorola version of KitKat? Pretty much the same thing just without the Motorola apps, settings, sounds and wallpaper?
I'm really happy with the Motorola software but wouldn't mind putting the Play edition on if it's much better
juzza87 said:
How do you find the Play Edition compared to the Motorola version of KitKat? Pretty much the same thing just without the Motorola apps, settings, sounds and wallpaper?
I'm really happy with the Motorola software but wouldn't mind putting the Play edition on if it's much better
Click to expand...
Click to collapse
Its not that much different.
The main issues i have with moto edition is that there is no internet calling in dialer (This is for VOIP accounts - Moto removed it from the Moto G for some reason and most 3rd party apps suck compared to native VOIP calling)
Minor issues (Nothing that can't be fixed with root)
- hidious career label in status bar (in en.GB 4.2.2)
- ugly dual SIM 2 signal bars wasting space on the status bar + 3G/H+ icon
- No useless Motorola apps that I don't need
Whats better in Moto ROM
- Camera App (GPE has no HDR)
- FM Radio (not in GPE)
- Faster file system (but this is barely noticable, GPE feels the same speed for me)
Is it ok to update to kitkat from 4.3? Ive only just tried it and says update available
Okay so here's the info to the best of my knowledge,
Phone Model : Moto G 3rd Gen (XT1550, dual sim, 2gb RAM, 16gb ROM, India)
Bootloader Status : Unlocked
Root Status : Rooted
Recovery : Stock
ROM : Stock ROM 5.1.1
I've been running the stock Recovery & ROM with high hopes of getting an official OTA Marshamallow update.
To truly customize the device to my liking I flashed the xposed framework (the arm version) , it worked fine and all the modules I installed worked perfectly.
I also had Device Control, Xposed Gels, and some other apps to bring my Stock ROM experience close to that of Cyanogen MOD.
When the OTA Marshmallow update started rolling in , I was unable to install the update even after successfully downloading the file numerous times. But i was so comfortable with my device and all the customization I had on my device that I decided to keep using my customized Stock ROM.
4 months later (now) the lack of a gyro in this device and my eagerness to get into VR headsets has left me with no choice but to sell it and get another phone. So i needed it in a sale worthy condition, without the customization and with the Marshmallow update installed.
I uninstalled the xposed framework and all the modules but was still unable to install the OTA update.
So i figured i'd install CyanogenMOD with TWRP custom recovery.
I have done this for quiet a lot of my friends and am fairly used to the steps involved. I use the " minimalADB fastboot " kit and my device on fastboot to flash recovery. For some reason i was not able to flash the lastest TWRP image (twrp-osprey-3.0.0-r2.img ) for the device nor was i able to boot from it :crying:. The fastboot command prompt on my PC would show success but the devices would not restart into the custom recovery like it is supposed to, but the device would stay at the fastboot mode and kept restarting everytime i selected the recovery mode option.
I had an older image (twrp-osprey-2.8.7-r3.img ) which i couldn't flash either but i was able to boot into TWRP with this image. From here i tried installing the latest CM12.1 nightly available (cm-12.1-20160227-NIGHTLY-osprey.zip) as soon as i swiped the device would just reboot, i tried this numerous times and with other nightly builds as well.
In haste and frustration i wiped the cache/dalvik , internal storage and system through TWRP , thinking that changes made in the quest of customizing my device were causing this hindrance. I had no OS now. I went over trying to flash TWRP and CM12.1 many times again with the same issues.
I came about a thread on How to " Fastboot Flash Moto G (3rd Gen) Factory Firmware Images " (http://forum.xda-developers.com/2015-moto-g/general/guide-fastboot-flashing-factory-t3187750) & used this firmware image " Retail Asia | India (2GB) - XT1550_OSPREY_RETASIA_DS_2GB_6.0_MPI24.65-25_cid7 ". Still no progress.
The bootloader unlocked warning has come back (i flashed a stock MOTO logo there earlier) which keeps flashing on my screen again and again , no booting into OS or anything else. Not even an error. As if there is no OS installed.
I have gone about the procedure in the above thread a couple of times, with no success and the same problem.
Is there any reason why i'm unable to flash a custom recovery or ROM ??? What am i missing???
Please help i'm stuck, pulling my hair out with no phone and completely frustrated.
Thanks in advance.
Did you check your build no for stock ROM?
samirza692 said:
Did you check your build no for stock ROM?
Click to expand...
Click to collapse
Nope. Too late for that now.
If you're asking in regard to the stock firmware I tried to flash, it didnt depend on the build number. Just the model number and the RAM.
ashrith.s said:
Nope. Too late for that now.
If you're asking in regard to the stock firmware I tried to flash, it didnt depend on the build number. Just the model number and the RAM.
Click to expand...
Click to collapse
okay i am not a developer nor a noop but trying to help you
try to flash stock rom from here http://forum.xda-developers.com/2015-moto-g/general/index-moto-g-factory-firmware-images-t3169639 but dont mistake this time double check your model with build number using carefuly the steps from here http://forum.xda-developers.com/2015-moto-g/general/index-moto-g-factory-firmware-images-t3169639
You will not brick the phone if you use the latest firmware and do a factory reset before flashing.
Good luck.
but do at your own risk i am not responsible for anything
samirza692 said:
okay i am not a developer nor a noop but trying to help you
try to flash stock rom from here http://forum.xda-developers.com/2015-moto-g/general/index-moto-g-factory-firmware-images-t3169639 but dont mistake this time double check your model with build number using carefuly the steps from here http://forum.xda-developers.com/2015-moto-g/general/index-moto-g-factory-firmware-images-t3169639
You will not brick the phone if you use the latest firmware and do a factory reset before flashing.
Good luck.
but do at your own risk i am not responsible for anything
Click to expand...
Click to collapse
the link provided is the exact same link from where I flashed a stock rom before.
build number for stock rom??? am i missing something???
all i see is the model variant (xt1550 is my phone)
RAM specification (mine is 2gb)
and the region (mine is retails asia | india )
so i went with the following firmware
Retail Asia | India (2GB) - XT1550_OSPREY_RETASIA_DS_2GB_6.0_MPI24.65-25_cid7
where does the build number come into the equation???
Please lemme know if im doing something wrong. Thanks for the replies.
So I've successfully flashed twrp-osprey-2.8.7-r3.img to my device and I've been able to boot into twrp. The touchscreen doesn't seem to respond though. It asks to swipe to begin and I'm stuck again.
I had the screen replaced a couple of days ago.
Could it be a faulty screen or a software issue?
P.S. I have not been able to flash any version of twrp after the above mentioned version (v 3.0.0 is the latest stable version) but the ones prior are flashable.
Hey, contact me via PM and il do my best to help you in this.
therealduff1 said:
Hey, contact me via PM and il do my best to help you in this.
Click to expand...
Click to collapse
Is not big issue
Is it still possible to boot back into the OS? If it is, check if you have OEM unlocking enabled, since you're on stock ROM, it might be gotten unchecked after unlocking your bootloader because that's what happened with me. If you do t wether or not that was checked, you're at a dead end and there's nothing you can do. You can try paying someone to fix it, i.e., Motorola.
I came from android nougat on my galaxy s8+, however, I wanted to update to oreo, so I flashed it through odin with all the necessary firmware files. I configured it all once after. However, OEM Unlock is missing from the developer options. I've read that you have to wait 7 days for it to appear but I don't have the time to wait as I have some projects to deal with. I'm wondering if I can dirty flash an old rom over stock rom to enable oem unlock through odin since I can't flash through twrp . Once I get the regular rom loaded, I'm going to flash twrp and find a custom rom based off oreo instead. Would be great if someone knows any work around for this.
TheFinalHawk said:
I came from android nougat on my galaxy s8+, however, I wanted to update to oreo, so I flashed it through odin with all the necessary firmware files. I configured it all once after. However, OEM Unlock is missing from the developer options. I've read that you have to wait 7 days for it to appear but I don't have the time to wait as I have some projects to deal with. I'm wondering if I can dirty flash an old rom over stock rom to enable oem unlock through odin since I can't flash through twrp . Once I get the regular rom loaded, I'm going to flash twrp and find a custom rom based off oreo instead. Would be great if someone knows any work around for this.
Click to expand...
Click to collapse
Did you get a valid answer? Tx
I am looking to completely flash back to stock, recovery included in order to receive OTA updates again and hopefully update to 9.0.
I am in the US region using the H3223 variant of the Xperia XA2 Ultra, running 8.0.0 with the March 1st, 2018 security update, rooted with the bootloaded unlocked and I have used an alternate recovery on the device before (TWPR).
Would someone be able to let me know what tools I'd need to properly flash the device, and where I could locate stock recovery images, as well as clean images of the stock firmware that I can safely flash to?
Thank you.
ThomasBags said:
I am looking to completely flash back to stock, recovery included in order to receive OTA updates again and hopefully update to 9.0.
I am in the US region using the H3223 variant of the Xperia XA2 Ultra, running 8.0.0 with the March 1st, 2018 security update, rooted with the bootloaded unlocked and I have used an alternate recovery on the device before (TWPR).
Would someone be able to let me know what tools I'd need to properly flash the device, and where I could locate stock recovery images, as well as clean images of the stock firmware that I can safely flash to?
Thank you.
Click to expand...
Click to collapse
I'm sure you probably found the answer by now, but you can go here:
https://forum.xda-developers.com/xa2-ultra/help/how-flash-to-stock-h3223-t3959331
Or you can try the great pie ROMs already made before you flash stock.... There is Lineage, RR, and AOKP under the development threads, just a thought. :laugh:
AlaskaLinuxUser said:
I'm sure you probably found the answer by now, but you can go here:
https://forum.xda-developers.com/xa2-ultra/help/how-flash-to-stock-h3223-t3959331
Or you can try the great pie ROMs already made before you flash stock.... There is Lineage, RR, and AOKP under the development threads, just a thought. :laugh:
Click to expand...
Click to collapse
I haven't found the answer by now, and when clicking that link, it just links back to this thread?
ThomasBags said:
I haven't found the answer by now, and when clicking that link, it just links back to this thread?
Click to expand...
Click to collapse
:laugh: Oops! Here is the link I intended to share:
https://forum.xda-developers.com/xa2-ultra/how-to/extracted-stock-h3223-rom-images-t3807548
Will flashtool relock bootloader?
Hey I was experiencing some display issues so I flashed a custom ROM to test / narrow the problem (hardware issue sadly).
—Now I'm not sure how to revert back to completely stock as I've never unlocked the bootloader and worked much with fastboot.
On Samsung's you just download the official stock file, get Odin and put the file into AP, flash, done.
On one plus this is a bit different, first of all there's barely any mentioning of GM-1910 in the MSMDownloaderTool thread(s), I also don't want to have Hydrogen OS.
—My OP7Pro came with Oxygen OS pre-installed, GM1910 "international version" ← def. Chinese with oxygen flashed over it.
*What have you altered so far?*
Unlocked Bootloader/OEM
Flashed TWRP with fastboot
Flashed Havoc 3.0 OS, Magisk, OpenGapps
My perspective on the nature of special relativity.
*What do I want to reset?*
EVERYTHING, ROM, recovery, bootloader, you name it, I don't care about apps and pictures. worth noting I have a One plus Switch Backup, does that help?
Look for the MSM tool... that can reset the phone completely back to stock.
UpdateYourBrowser said:
Hey I was experiencing some display issues so I flashed a custom ROM to test / narrow the problem (hardware issue sadly).
—Now I'm not sure how to revert back to completely stock as I've never unlocked the bootloader and worked much with fastboot.
On Samsung's you just download the official stock file, get Odin and put the file into AP, flash, done.
On one plus this is a bit different, first of all there's barely any mentioning of GM-1910 in the MSMDownloaderTool thread(s), I also don't want to have Hydrogen OS.
—My OP7Pro came with Oxygen OS pre-installed, GM1910 "international version" ← def. Chinese with oxygen flashed over it.
*What have you altered so far?*
Unlocked Bootloader/OEM
Flashed TWRP with fastboot
Flashed Havoc 3.0 OS, Magisk, OpenGapps
My perspective on the nature of special relativity.
*What do I want to reset?*
EVERYTHING, ROM, recovery, bootloader, you name it, I don't care about apps and pictures. worth noting I have a One plus Switch Backup, does that help?
Click to expand...
Click to collapse
You can use the fastboot ROM or Guac (MSM tool for oxygen OS). Links below:
https://forum.xda-developers.com/oneplus-7-pro/how-to/msm-tool-guac-t3934691
or
https://forum.xda-developers.com/oneplus-7-pro/how-to/rom-stock-fastboot-roms-oneplus-7-pro-t3931424
Good luck!!
Gr8man001 said:
You can use the fastboot ROM or Guac (MSM tool for oxygen OS). Links below:
https://forum.xda-developers.com/oneplus-7-pro/how-to/msm-tool-guac-t3934691
or
https://forum.xda-developers.com/oneplus-7-pro/how-to/rom-stock-fastboot-roms-oneplus-7-pro-t3931424
Good luck!!
Click to expand...
Click to collapse
excuse my stupidity but given that I want to get rid of my custom ROM and back to stock oxygen which tool do I have to use?
secondly all images (androidfilehost) for the second link are for GM1911,17,13,15 but mine is 1910 which is not listed, what do I do now?
UpdateYourBrowser said:
excuse my stupidity but given that I want to get rid of my custom ROM and back to stock oxygen which tool do I have to use?
secondly all images (androidfilehost) for the second link are for GM1911,17,13,15 but mine is 1910 which is not listed, what do I do now?
Click to expand...
Click to collapse
I am sorry but I am not familiar with Chinese stock ROMs. For some reason, I got the impression that you wanted to restore it to an international version and not the Chinese/HK version. You may want to post a question in the OnePlus community forum or check out their download section for your specific model.
https://forums.oneplus.com/forums/oneplus-7pro-support/
Gr8man001 said:
I am sorry but I am not familiar with Chinese stock ROMs. For some reason, I got the impression that you wanted to restore it to an international version and not the Chinese/HK version. You may want to post a question in the OnePlus community forum or check out their download section for your specific model.
https://forums.oneplus.com/forums/oneplus-7pro-support/
Click to expand...
Click to collapse
no no I want to restore it to international version, the phone itself is GM1910. should I flash GM21AA file or the global file?
I think I will go with the global file, makes most sense in this moment
UpdateYourBrowser said:
no no I want to restore it to international version, the phone itself is GM1910. should I flash GM21AA file or the global file?
I think I will go with the global file, makes most sense in this moment
Click to expand...
Click to collapse
GM21AA should be fine. If you decided to use the MSM tool (the one in the first link), hardest part is to get the L2/qualcomm drivers installed on your PC with the method described. Alternatively you can download and install the drivers yourself which will make the job easier. This will LOCK your bootloader and wipe off everything on your phone. You will get a brand new phone running 10.0.3 OS
Easiet way would be to go fastboot ROM route. It will also wipe your phone but won't lock the bootloader. Once installation is complete you could use the adb command to lock the bootloader. It's one extra step but may be much easier IMO. Download the zip file on PC>unzip it>Hit flash all bat file while the phone is connected in the fastboot mode. You may get some error messages regarding header parsing, ignore them and sit tight until your phone boots.
Good luck!!
WORKS NOW! Can confirm this reverts all back to stock (it will revert back to Oxygen OS (OOS) 9.5 so you'll have to update to Android 10 via OTA if you want)
For anyone wondering, I had Android 10 installed before / Havoc 3.0 and the MSMTool will revert you back to Oxygen OS 9.5. Widevine jumped back to L1 so everything should be stock.
If you have any questions, don't wait, I am sure someone out there had the same questions/issue as me and I hope this will help you.
https://forum.xda-developers.com/oneplus-7-pro/how-to/msm-tool-guac-t3934691
UpdateYourBrowser said:
WORKS NOW! Can confirm this reverts all back to stock (it will revert back to Oxygen OS (OOS) 9.5 so you'll have to update to Android 10 via OTA if you want)
For anyone wondering, I had Android 10 installed before / Havoc 3.0 and the MSMTool will revert you back to Oxygen OS 9.5. Widevine jumped back to L1 so everything should be stock.
If you have any questions, don't wait, I am sure someone out there had the same questions/issue as me and I hope this will help you.
https://forum.xda-developers.com/oneplus-7-pro/how-to/msm-tool-guac-t3934691
Click to expand...
Click to collapse
Hey, I have a problem, I re-locked the bootloader, it is currently blocked, but my Widevine status is still L3, can you tell me if you used MsmTool first and then you did relock, or did you block the bootloader first?