Related
I have had a UK SII since launch (originally on O2) but rooted and now using CM9.
Ive noticed recently that my charger needed to be wiggled a bit in the port for the phone to start charging.
Now it seems to have gotten worse and now i have to have the plug tilted in the usb port at a certain angle and apply pressure to it for it to start charging. Ive tested with 4 different leads. Connected to my laptop and phone keeps on flicking to usb debugging message so i am presuming the connections in the usb port are faulty.
Ive also cleaned a load of fluff out from it and its still the same.
The phone is just under a year old... so im hoping its covered for a 2 year cover like my old Sony Erricson phone.
Do you think they will repair this fault or make me pay due to excessive wear n tear?
I charge once a day over night, and dont use the port for much else apart from probably undre 20times connected to laptop.
Thanks
did you try the cable with something else than your phone? It looks like it's probably some broken part of the cable inside, but try anyway.
If it works fine with everything else it's your phone, if doesn't work with other things it's the cable and i'm not sure if they would replace it, because it could be your fault if it's the cable.
Vincentmrl said:
did you try the cable with something else than your phone? It looks like it's probably some broken part of the cable inside, but try anyway.
If it works fine with everything else it's your phone, if doesn't work with other things it's the cable and i'm not sure if they would replace it, because it could be your fault if it's the cable.
Click to expand...
Click to collapse
As I described above... i have tested the phone with 4 different usb cables/chargers.
I'm just posting for brief warning/general info for you guys. When I got to work tonight I plugged in my USB OTG cable which I have been using w/ no issues on both my N7 and S3 since July and then plugged in a 64gb flash drive that I have also been using since launch. When I plugged in the flash drive, I heard a pop, the screen went blank and the phone is totally dead. A quick search showed while this isn't incredibly common, it has happened to several people. Most blamed the OTG cable, but I disceted mine and it had no broken wires and no shorts. I turned up a thread on root wikiz that basically said that it is the power management IC self destructing and there is nothing that can be done to repair it. So, just a heads up if you use OTG-- I am not sure I will use it again on this phone as it seems it is just a matter of time...
Later,
Jason
jacampb2 said:
I'm just posting for brief warning/general info for you guys. When I got to work tonight I plugged in my USB OTG cable which I have been using w/ no issues on both my N7 and S3 since July and then plugged in a 64gb flash drive that I have also been using since launch. When I plugged in the flash drive, I heard a pop, the screen went blank and the phone is totally dead. A quick search showed while this isn't incredibly common, it has happened to several people. Most blamed the OTG cable, but I disceted mine and it had no broken wires and no shorts. I turned up a thread on root wikiz that basically said that it is the power management IC self destructing and there is nothing that can be done to repair it. So, just a heads up if you use OTG-- I am not sure I will use it again on this phone as it seems it is just a matter of time...
Later,
Jason
Click to expand...
Click to collapse
From another forum...but saw your thread. Does this mean your phones is screwed or just the charger?
Jarmezrocks said:
From another forum...but saw your thread. Does this mean your phones is screwed or just the charger?
Click to expand...
Click to collapse
Phone
Sent from my Galaxy SIII
Which USB cable did u use?
Sent from my SGH-T999 using xda premium
jacampb2 said:
I'm just posting for brief warning/general info for you guys. When I got to work tonight I plugged in my USB OTG cable which I have been using w/ no issues on both my N7 and S3 since July and then plugged in a 64gb flash drive that I have also been using since launch. When I plugged in the flash drive, I heard a pop, the screen went blank and the phone is totally dead. A quick search showed while this isn't incredibly common, it has happened to several people. Most blamed the OTG cable, but I disceted mine and it had no broken wires and no shorts. I turned up a thread on root wikiz that basically said that it is the power management IC self destructing and there is nothing that can be done to repair it. So, just a heads up if you use OTG-- I am not sure I will use it again on this phone as it seems it is just a matter of time...
Later,
Jason
Click to expand...
Click to collapse
This happened to me. Verizon will warranty the phone. I wondered what actually blew up in the hardware. I am surprised it hasn't happen to more people, seeing how you really don't have any control over whether it blows up or not.
RotaryXperiment7 said:
Which USB cable did u use?
Click to expand...
Click to collapse
This. I just ordered one lol.
jacampb2 said:
I'm just posting for brief warning/general info for you guys. When I got to work tonight I plugged in my USB OTG cable which I have been using w/ no issues on both my N7 and S3 since July and then plugged in a 64gb flash drive that I have also been using since launch. When I plugged in the flash drive, I heard a pop, the screen went blank and the phone is totally dead. A quick search showed while this isn't incredibly common, it has happened to several people. Most blamed the OTG cable, but I disceted mine and it had no broken wires and no shorts. I turned up a thread on root wikiz that basically said that it is the power management IC self destructing and there is nothing that can be done to repair it. So, just a heads up if you use OTG-- I am not sure I will use it again on this phone as it seems it is just a matter of time...
Later,
Jason
Click to expand...
Click to collapse
Sorry to here about your phone. I was jut about to go buy one of these cables.
This same thing happened to my phone a few weeks ago. It went totally dead out of nowhere, I was taking photos at the time.
You shouldn't have a problem getting a replacement even if you don't have insurance.
Good Luck
I have heard stories about that happening, though its not common, it is surprising that its so low considering its random and no one knows exactly what causes it
at least you don't have to factory restore before returning
Sorry guys, I just woke up. Was on graveyard shift last night. Anyhow, the cable was a generic ebay right angle otg cable, about 5" or so in length. I am 99% certain it had nothing to do with the cable though, just a hardware problem. As mentioned above I dissected the cable and it had no problems. I could still use it on my Nexus 7 with no issues. I had the cable plugged in before inserting the flash drive and it was fine until the flash drive was plugged it.
The Root Wikiz thread I mentioned said that someone had sent theirs in to be Jtag'ed thinking it was just hard bricked. The response from the people where he sent it was that they had seen a number of them with the PMIC damaged and that there was nothing that their services could do for them.
My guess is there are some marginal PMIC's out there and that when they switch the port from charge to host mode they just cant take the current and pop. The fact that I made it nearly 5 months using the same OTG cable on a regular basis kind of lends credence to this theory, but who knows. All I know is that it was totally dead, absolutely no signs of life regardless of what I tried.
FWIW I was rooted and running paranoid android, but I have found reports of this happening to bone stock phones as well as any variation of ROM. Verizon did warranty the device. Oddly, the tech told me "I have never heard of this happening" but didn't even ask me to try anything with the phone, he just said that they would ship me a new one for warranty replacement.
New device is here, I'm off to root and unlock! Good luck guys.
Later,
Jason
jacampb2 said:
Sorry guys, I just woke up. Was on graveyard shift last night. Anyhow, the cable was a generic ebay right angle otg cable, about 5" or so in length. I am 99% certain it had nothing to do with the cable though, just a hardware problem. As mentioned above I dissected the cable and it had no problems. I could still use it on my Nexus 7 with no issues. I had the cable plugged in before inserting the flash drive and it was fine until the flash drive was plugged it.
The Root Wikiz thread I mentioned said that someone had sent theirs in to be Jtag'ed thinking it was just hard bricked. The response from the people where he sent it was that they had seen a number of them with the PMIC damaged and that there was nothing that their services could do for them.
My guess is there are some marginal PMIC's out there and that when they switch the port from charge to host mode they just cant take the current and pop. The fact that I made it nearly 5 months using the same OTG cable on a regular basis kind of lends credence to this theory, but who knows. All I know is that it was totally dead, absolutely no signs of life regardless of what I tried.
FWIW I was rooted and running paranoid android, but I have found reports of this happening to bone stock phones as well as any variation of ROM. Verizon did warranty the device. Oddly, the tech told me "I have never heard of this happening" but didn't even ask me to try anything with the phone, he just said that they would ship me a new one for warranty replacement.
New device is here, I'm off to root and unlock! Good luck guys.
Later,
Jason
Click to expand...
Click to collapse
Wow, that sucks, but I am glad you got another S3. I have been using this one that I got from Amazon. It has a couple of usb ports and 2 card readers. I have been very happy with it. It is extremely useful when I am at family functions, and everyone has taken a lot of pictures and video. I can grab their cards and pull the pics and video onto my 64 Gig SD card on my phone. People are amazed I can do this with my phone! However, now I am a little worried about using it. I will keep this in mind, and only use it on the occasions that I really need it. Thanks for the heads up!
Rob
my s3 discharging immediately
hi everybody....
i have an issue with my s3....i make an OTG cable and plug it into my s3...and i just can get power from it,no data.
but i think the s3 is already wasting power and i must charging it after a day.
can anybody help me!!!!!
arminghm said:
hi everybody....
i have an issue with my s3....i make an OTG cable and plug it into my s3...and i just can get power from it,no data.
but i think the s3 is already wasting power and i must charging it after a day.
can anybody help me!!!!!
Click to expand...
Click to collapse
One day charge is normal if using phone. If gonna use OTG you are overusing and can expect 1/2 day. Buy good cable if want data.
I had something similar happen except, my usb sent a static spark from my oc to my phone. Didn't fry it completely, but messed up something that would no longer dock to pc, dock to car our go into deep sleep.
Wonder if the two issues are related.
Be sure to discharge any static in you usb called before plugging them into your phone.
Sent from my SCH-I535 using xda app-developers app
prdog1 said:
One day charge is normal if using phone. If gonna use OTG you are overusing and can expect 1/2 day. Buy good cable if want data.
Click to expand...
Click to collapse
your right..but its used for 3 days....i bought an otg cable and use it...thats amazing...i can use mouse,keyboard and other devices in my s3.
but i still have my problem...
my s3 is in flight mode and and doesnt do anything...but its discharging..and i dont know the problem is sent from my os or my hardware..
idont kno that the os is screwed up or is something wrong with battery.
is there any command that tell os to dont discharging???
i love my s3 so much
arminghm said:
your right..but its used for 3 days....i bought an otg cable and use it...thats amazing...i can use mouse,keyboard and other devices in my s3.
but i still have my problem...
my s3 is in flight mode and and doesnt do anything...but its discharging..and i dont know the problem is sent from my os or my hardware..
idont kno that the os is screwed up or is something wrong with battery.
is there any command that tell os to dont discharging???
i love my s3 so much
Click to expand...
Click to collapse
Discharging is what the battery always does when not plugged into A/C power and turned on, and even sometimes when it is plugged into A/C power (when you get in the top 10% of full it starts going through discharge/charge cycles to keep it within the top 10% of power but never totally full. This prevents overcharging and explosions)
That said:
A sudden reduction in the runtime for the battery under the same average load is almost always the battery going bad.
If you mean the battery doesn't last as long because you now use OTG - those things you plug into the phone need to get their power somewhere. The phone battery is it.
So now you are powering the phone + whatever other things you attach to it. Some of them can drain a lot more power then you might think. You just never noticed much (if at all before) because your total reserves weren't such a tiny amount.
If you stop using OTG devices and your battery capacity bounces right back up to where it was before, then you can reasonably infer the extra gadgets are the culprit.
(if you stop OTG stuff for a few days and the battery still sucks when before it didn't, probably need to buy a new battery because yours is most likely shot.)
Assuming it seems to work fine...
So two choices, right? No accessories and lots of battery life, or lots of accessories and no power to run them with.
well...not really:
It's probably not always possible - but how often do you use OTG near A/C power?
Whenever you are near somewhere you can plug in, the first thing you should plug into your OTG cable (besides the phone) is a USB hub with a power cord.
...and really, if you want to use those power hungry USB hard drives and things like that, then you really can't without taking the stress off of the phone of supplying that power - that hard drive just half spins up like a car that cranks but won't start.
Every crank in that car wears the battery down and beats up the starter when it doesn't fire up the engine. Just like every spin up but not quite read of the hard drive puts incredible load on the S3 to try to throw enough current at it fast enough to keep it happy. Just beating it up for nothing.
Which brought me to what I wanted to bring up for some consideration:
Think about trying to use a powered hub whenever you can as the first thing off the OTG cable, should take an immense amount of stress off of the S3 in making it all work.
Bet at the least you reduce the risk of popping since the power spikes will be much less - that powered hub is a pretty solid buffer for that kind of stuff when you are constantly popping flash drives in and out.
I remember way back when for the Nook Color when some really sharp people made OTG happen out of the thin air - no way Barnes & Noble had that on even a remote list of possibilities when they were ready to throw the device to the masses and see what happened.
If you wanted to use more then the smallest of thumb drives you needed a powered hub. The device wasn't designed for it, and simply wasn't able to squeeze more then a paltry amount of power out in reverse. (but it was just enough to talk to a powered hub...)
Anywhere that you can plug in your powered buffer should contribute to avoiding the problem the OP posted about. The thought experiment (hopefully) growing from this post? How much truth does this theory exhibit?
Edit: Totally missed this post:
arminghm said:
hi everybody....
i have an issue with my s3....i make an OTG cable and plug it into my s3...and i just can get power from it,no data.
but i think the s3 is already wasting power and i must charging it after a day.
can anybody help me!!!!!
Click to expand...
Click to collapse
Here you say you made an OTG cable, the first post I quoted you in you said you bought one. If you made it, i'd say that is your problem.
The quality of the cable you use absolutely matters. Higher quality parts = higher quality results.
I have a bunch of micro USB cables (as i'm sure many of you do also - ) ... and from some of them I get an absolute night/day result in charging.
Some cables (mostly the ones from the dollar store or older cables) just plain suck. They can't bring enough power from the same A/C adapter as my OEM HTC/Samsung cables. (I have some motorolla OEM cables from around the time of the droid X launch - they are closer to the dollar store cables in quality - haven't tried recent motorolla OEm cables, hopefully they got better or I got a bad batch over a six month period)
Using the low quality cables I can absolutely lose power plugged in just being a wifi hotspot with the screen on, until it eventually goes critical and dies. (this I tend to notice when my pc banished to the corner of nowhere loses all network connectivity) - whereas with the HTC/Samsung cables from within the last two years keep me near full with that being the only difference.
I'd rather have a few good cables then a bag full of POS dollar store ones. That little bit better material, little bit tighter QC adds up to a big difference in the final outcome.
This same thing happened to me when I plugged the same type of cheap right elbow OTG cable from ebay into my brand new S3 (2 days old with about one hour of usage). The cable worked fine with USB drives, a mouse, or a keyboard used alone on the S3. The cable was plugged into a USB 4 port hub with multi-card reader. The screen was off when I plugged it in so it appeared to just be off. Any attempts to power it on were fruitless. I smelt the phone right afterward and there wasn't any burnt smell. Plugging in the phone resulted in it getting pretty warm but not to an extreme yet the battery remained cool. It appears to have burnt something between the battery and lines but leaving the components intact thus causing the excess of heat. BTW the hub/reader is fine. I won't be using that again on my new one but I will be attempting to use a different hub that has been working fine on my wife's RAZR MAXX HD. Just hope this is a very isolated incident and not a bad batch from the retailer.
Edit: The S3 is a blue 16G Verizon model. The S3 was on stock ROM when this happened (not like that would prevent death from inferior circuit protection components).
Were you using a powered hub, or passive hub?
Anyone tried a DAC off the OTG cable?
BowDown said:
Were you using a powered hub, or passive hub?
Anyone tried a DAC off the OTG cable?
Click to expand...
Click to collapse
Don't do it. I've fried 2 GS3s with a UCA-220 DAC over otg.
First time with a regular OTG cable, the second time with a OTG/phone charging cable, the power came unplugged and zap. I'm lucky Verizon has replaced the phone two times.
I think the best solution is to completely isolate the DAC power from the phone power. A circuit to charge the phone with the otg/charge cable and a separate circuit to power the DAC.
uber_mike said:
Don't do it. I've fried 2 GS3s with a UCA-220 DAC over otg.
First time with a regular OTG cable, the second time with a OTG/phone charging cable, the power came unplugged and zap. I'm lucky Verizon has replaced the phone two times.
I think the best solution is to completely isolate the DAC power from the phone power. A circuit to charge the phone with the otg/charge cable and a separate circuit to power the DAC.
Click to expand...
Click to collapse
Wouldn't use of a powered usb hub remove any power issues? I purchased a OTG cable today.. I had planned to connect it to a powered hub, and run the DAC off that?
Hello, a lot of weird things have started happening to my device lately.
The first occurrence was screen burn in, like on plasma TVs. If I look closely on a white background, I can see that the letters on my keyboard have lightly burned into the screen! A week or so later, the top bar of the Android SMS app has burned in as well. Does warranty cover this or anything?
The second major problem is charging. Before, I could be plugged into the wall and use my phone without draining my battery, at all. Now things have changed, I am losing battery, while charging!
The last thing is that my PC no longer recognizes my device.. Yes, I do have the USB drivers, they have always been installed and have been working fine. Just in case, I tried reinstalling them, didn't help. I plug in my USB and the phone starts charging, but I don't get that notification that I used to that a connection has been established with my computer. I have tried all my USB ports, nothing changes. I am unable to browse my device's file system.
I am not too concerned about the screen, but I am very worried about the charging/connection issue; they seem to be related.
My question is, what do you think is wrong? Is there a problem with the battery? The charging port? The USB cable? Maybe CleanROM has been corrupted in some way?
I should also mention that when unplugging my phone from the charging source, it seems to think it is still charging for up to a minute later.
And, if you move the device in a certain way when it is charging, it seems to lose connection to the charging source - the screen lights up and says it's not charging until you revert it to its original position.
Any replies are greatly appreciated!
Do you guys think this is a problem with the cable? I'd like to try buying a new one if this is the case.
Does anyone have a link to a genuine data cable for the i535? (preferably on Amazon) I want to make sure I buy the right one!
What you describe is typical of a failing charge port. The only other thing that will give the symptoms you describe is a bad charger. Try a different charger and if the same thing happens then you need a new port. You can buy a repair service for this on eBay for $25
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
Kemotar said:
What you describe is typical of a failing charge port. The only other thing that will give the symptoms you describe is a bad charger. Try a different charger and if the same thing happens then you need a new port. You can buy a repair service for this on eBay for $25
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
Click to expand...
Click to collapse
Hi, I actually narrowed it down to the USB charging cable. I managed to dig up another one and it works just fine now.
That's the first USB cable I've ever had fail!
EatonZ said:
Hi, I actually narrowed it down to the USB charging cable. I managed to dig up another one and it works just fine now.
That's the first USB cable I've ever had fail!
Click to expand...
Click to collapse
Did that also fix the issue you had with the burn in? I'm just curious
dwibbles33 said:
Did that also fix the issue you had with the burn in? I'm just curious
Click to expand...
Click to collapse
Nope, that's probably there to stay.
I doubt the problems were related.
EatonZ said:
Nope, that's probably there to stay.
I doubt the problems were related.
Click to expand...
Click to collapse
I was thinking the same thing but I've seen chargers do some weird s**t if you're still under warranty that should be covered. Otherwise I would enable daydream in display settings. Its a fancy word for screensaver but obviously would benefit you.
I just noticed that my charging port is extremely loose and any USB cable I stick in there has a lot of wiggle room. Because of this if I move my phone while charging it sometimes looses it's connection. I don't believe it ever did that before. Does anybody else notice a loose fit or is it just my phone?
Sent from my SM-N920V using Tapatalk
My charging port is pretty solid. But just to avoid this scenario, I got the samsung wireless fast charger pad
Sent from my SM-N920V using Tapatalk
Couple of things, if you have a case, try charging without it on. Otherwise try another cable. I thought mine was loose too but it ended up just being a cable that didn't fit well.
Thanks for the feedback guys. My case doesn't come into contact with the charging port or the cable when it's inserted. I use the original cable and a cheap chinese one intermittently. The Chinese one is quite long which is why I use it, but it wiggles much more than the original. I'm pretty sure there was no wiggle at all in the beginning so it must be from using the cheap cable. Note to self (and others): "Don't do that!"
Sent from my SM-N920V using Tapatalk
Hi there, I'm having the same issue. The thing is that I don't remember if it worked well from the start.
I always use an alternative charger and keep the original in the packaging.
One day noticed that at least 1/4 part of the plug remains out of the socket. This makes the plug wiggle and remain loose. Sometimes (a Tagwood cable) disconnects by the own weight.
I don't hear the common 'click' when plugging in or out.
Tried different cables, many including the original and every does the same.
I don't know if it is a design issue or a broken thing.
What I can see, I don't find any anomalies. Neither where is bottoming. It looks very sensitive parts so I don't want to touch it.
I only noticed that socket looks shorter than other micro USB plugs.
Sorry for my English.
If there's any suggestions I want to hear it.
hellcore said:
Hi there, I'm having the same issue. The thing is that I don't remember if it worked well from the start.
I always use an alternative charger and keep the original in the packaging.
One day noticed that at least 1/4 part of the plug remains out of the socket. This makes the plug wiggle and remain loose. Sometimes (a Tagwood cable) disconnects by the own weight.
I don't hear the common 'click' when plugging in or out.
Tried different cables, many including the original and every does the same.
I don't know if it is a design issue or a broken thing.
What I can see, I don't find any anomalies. Neither where is bottoming. It looks very sensitive parts so I don't want to touch it.
I only noticed that socket looks shorter than other micro USB plugs.
Sorry for my English.
If there's any suggestions I want to hear it.
Click to expand...
Click to collapse
Samsung phones have suffered from charging port issues for years. My Note 3 drove me crazy with it. You can try contacting Samsung, but I'm not sure what they would do.
Action123 said:
Samsung phones have suffered from charging port issues for years. My Note 3 drove me crazy with it. You can try contacting Samsung, but I'm not sure what they would do.
Click to expand...
Click to collapse
I had a Norte 3 and the plug was very strong and tighten.
Also 3.0 charged twice faster than other phones.
The phone is not buyed in my country. I can't contact Samsung
Guys, my brother had the exact same issue with his.
It ended up being lint that built up inside the port. Take a pin and clean the port out. I was shocked at how much lint (just from a normal pocket) got stuck in the port. Its definitely worth checking.
Worked for me!
CISGS said:
Guys, my brother had the exact same issue with his.
It ended up being lint that built up inside the port. Take a pin and clean the port out. I was shocked at how much lint (just from a normal pocket) got stuck in the port. Its definitely worth checking.
Click to expand...
Click to collapse
-------------------------------
At first my charging cable worked fine, but over time the connection became very touchy. Based on the post above, I opened up a paperclip and fished around the port area and was surprised by the lint that came out. Now my cable is connecting more securely and charging more reliably. Thanks for the tip!
Hi All,
I'm hoping someone here can share their opinions.
Recently I've been having charging issues with my XZ Premium. Started a few weeks ago, with the charger plugged in, it would randomly stop and start charging.
Lately it's been getting much worse. I have tried different chargers, cables, adapters etc. The original Sony USB cable plugged into a wall charger, and my laptop. My Dell laptop USB-C (thunderbolt) wall charger, as well as my Dell external battery charger, as well as MicroUSB cables with a USB-C adapter.
Without touching the cables or moving anything, sometimes it'll start or stop charging randomly.
I personally think it's the phone's USB-C connector. I've tried to clean it using a damp wooden toothpick and got some dust out, but it didn't make any difference.
The phone is rooted, and is out of warranty anyways. I also have a lot of security features installed which would make it hard for a tech to troubleshoot (needs passwords etc to be shut down or rebooted) and I store some cryptocurrencies in wallets on my phone.
Is it worth taking it to a tech (I live in Japan, and don't speak much Japanese) or should I be looking at an upgrade? If so, what is the recommended phone from Sony currently? I honestly really like the XZ Premium, so I'm tempted just to buy another one if mine can't be easily fixed.
Thanks!
Bit of an update.
I managed to get my phone to charge using the original Sony USB -> USB-C cable, with an adapter plugged into the thunderbolt port on my laptop. Charging is still incredibly slow though. Also, I noticed when it hit 30% charge, it stopped accepting charge unless the phone is unlocked. If I hit the lock button, the charge light switches off. It switches on again when I unlock it.
*Small edit* It stopped charging again at 31%, despite being unlocked.
Wiggling the cable in the phone socket doesn't seem to effect whether it charges or not, which should rule out the connector in the phone. It has also not registered as a device on my laptop, despite being connected via the USB cable, which would mean it's not specifically a battery issue either, as there's no data connection being made.
So I'm starting to think it's a hardware issue.
I've ordered a new Xperia XZ Premium, because I really do love this phone, and the new XZ2 Premium doesn't seem like much of an upgrade to me apart from the camera, and slightly faster performance. And as much as I'd love to have wireless charging, moving the finger print sensor, and no 3.5mm audio output is a massive dealbreaker for me.
mine died like this, was on charge, started to say charghing/discharghing until he turned off and never came back.. under warranty they changed MoBo/2 stickers/components (??)/ 2 screw and now is back like new
Long term bump.
I bought a new replacement 8142 and have been using that successfully, and I decided to try and fix the charging issues on my old one.
I've just installed a brand new genuine battery, charging port, and power/vol/camera button connections.
The phone booted up fine, but it's STILL not charging at all. Any ideas? Motherboard maybe?
tombow said:
Long term bump.
I bought a new replacement 8142 and have been using that successfully, and I decided to try and fix the charging issues on my old one.
I've just installed a brand new genuine battery, charging port, and power/vol/camera button connections.
The phone booted up fine, but it's STILL not charging at all. Any ideas? Motherboard maybe?
Click to expand...
Click to collapse
Maybe the flex cable isn't working
have only just started having this issue yesterday, have tried different charger and usbc cable combinations, cant even get my pc to recognise it as a plugged in turned off xzp and it wont turn on only show the battery icon with low level indicator in the red.
I have a similar issue.
When I connect my XZP to the pc using a Rampower cable USB-C to USB (sold as 5Gbps and 5V/3A power, thus an USB3.0 with fast charge of 15W) I suffer of the same issue exposed above: randomly the connection get interrupted.
While, charging the phone, yet with the above-mentioned cable and original Sony charger, I get no problem at all!
NB: I have never tried with the original USB cable...
Common fault with the xzp.
The actual connector from the logic board that the usb c module connects to burns out. Require a new logic board or connector to be replaced/soldered on and new usb c module.
kw0n2k said:
Common fault with the xzp.
The actual connector from the logic board that the usb c module connects to burns out. Require a new logic board or connector to be replaced/soldered on and new usb c module.
Click to expand...
Click to collapse
This is good news, because sourcing a mainboard is half the price of the phone, and I've already spent money on a new battery and charging port etc.
My 2nd G8142 phone has just started displaying the same symptoms, and I can't afford a complete replacement.
Can you confirm that this is the part I need? https://www.aliexpress.com/item/4000160901916.html
If so, I'll grab 2, and install into my old phone first to confirm the fix, before then installing one in my newer phone.
tombow said:
This is good news, because sourcing a mainboard is half the price of the phone, and I've already spent money on a new battery and charging port etc.
My 2nd G8142 phone has just started displaying the same symptoms, and I can't afford a complete replacement.
Can you confirm that this is the part I need? https://www.aliexpress.com/item/4000160901916.html
If so, I'll grab 2, and install into my old phone first to confirm the fix, before then installing one in my newer phone.
Click to expand...
Click to collapse
Im onto my second xzp and never had a charging issue
Beetle84 said:
Im onto my second xzp and never had a charging issue
Click to expand...
Click to collapse
Lucky you!
I'm onto my 2nd one, and have had the same charging issues with both.
Both phones have been rooted with a custom ROM, and I use my Dell smart-powerbank to charge them fairly often. So perhaps that is the cause of the early failures on both.
tombow said:
Lucky you!
I'm onto my 2nd one, and have had the same charging issues with both.
Both phones have been rooted with a custom ROM, and I use my Dell smart-powerbank to charge them fairly often. So perhaps that is the cause of the early failures on both.
Click to expand...
Click to collapse
I have unlocked both on day one :laugh:
I have never used a powerbank, could be a factor. Or just bad luck
My first xzp, i cracked the screen trying to replace the screen adhesive, so i bought a rosso red one from ebay.
tombow said:
This is good news, because sourcing a mainboard is half the price of the phone, and I've already spent money on a new battery and charging port etc.
My 2nd G8142 phone has just started displaying the same symptoms, and I can't afford a complete replacement.
Can you confirm that this is the part I need? https://www.aliexpress.com/item/4000160901916.html
If so, I'll grab 2, and install into my old phone first to confirm the fix, before then installing one in my newer phone.
Click to expand...
Click to collapse
Unfortunately I can't confirm if that is the exact part you need as I don't do repairs. All I can confirm is that my repairer has stated that he has seen XZP's with the same recurring issue with the connector burning out.
My guess is, that is the part as he had to micro solder a new connector to the logicboard.
kw0n2k said:
Unfortunately I can't confirm if that is the exact part you need as I don't do repairs. All I can confirm is that my repairer has stated that he has seen XZP's with the same recurring issue with the connector burning out.
My guess is, that is the part as he had to micro solder a new connector to the logicboard.
Click to expand...
Click to collapse
That's good enough for me! I'll grab a couple of them and see if it fixed my older phone first (because I've already tried the battery and the USB-C socket etc) Will update once I've done the repair.
Hope you can fix that problem and share some experience on this issue. Mine has a similar problem. The difference is that it can be charged to 100% but very slow and randomly stop.
sala499 said:
Hope you can fix that problem and share some experience on this issue. Mine has a similar problem. The difference is that it can be charged to 100% but very slow and randomly stop.
Click to expand...
Click to collapse
Yep, that's how my issue started too. It'll progressively get worse.
I've just bought a Google Pixel 3 XL as my 2nd XZP has ceased accepting any charge at all. I'll see if these motherboard sockets fix the issues, then keep one and sell one. Otherwise I'll just sell them both off as parts.
tombow said:
Yep, that's how my issue started too. It'll progressively get worse.
I've just bought a Google Pixel 3 XL as my 2nd XZP has ceased accepting any charge at all. I'll see if these motherboard sockets fix the issues, then keep one and sell one. Otherwise I'll just sell them both off as parts.
Click to expand...
Click to collapse
I talked to some tech on Alibaba (A Chinese shopping website) and they said it can be fixed by replacing that socket. But the replacement requires professional welding equipment and skills. Or the motherboard can be damaged. That's why I am looking for other people's experience before I take step myself. If you succeed, please update this thread. I think there are more people like me who is looking for successful experience from others. Thank you for your sharing.:good: