Hello,
I have successfully installed TWRP and a custom ROM on a UHANS A101S. And now I want to share the files and instructions, because they come from Russian forum 4pda.ru (thanks and credits to them).
Warning: I do not take any responsibility for whatever outcome you have when trying this on your device. It worked for me, but everything you do is your own risk.
Now, here's how it worked for me:
(Instructions are for UHANS A101S only, NOT for A101)
Installation of TWRP:
1. Download TWRP recovery image for UHANS A101S. Check that you get the correct recovery.img for your firmware build. Also download the scatter file for the UHANS A101S.
2. Download SP Flash Tool and driver for UHANS A101S.
3. Install driver on your PC and reboot your PC.
4. Unpack SP Flash Tool. Unpack scatter file. Put scatter file in same folder as recovery.img file.
5. On your phone, enable USB debugging mode in developer settings. (To activate developer settings menu, tap 7 times on your build number in Settings > About).
6. Switch off phone. Remove battery. Wait for 10 seconds. Put battery back into your phone, but don't start it! Keep it switched off.
7. Start SP Flash Tool with Admin permission. Click "scatter-loading" and navigate to the folder where you unpacked the scatter file and select it. Make sure that "Download Only" is selected in drop-down menu on the left. Then click the "Download" button in SP Flash Tool.
8. Connect your phone to the USB port of your PC and press Volume Up on your phone, so SP Flash Tool will recognize it.
9. If everything goes fine, in SP Flash Tool a red progress bar at the bottom turns yellow, then green and finally you get a pop-up with a green check mark.
10. Now you can boot into TWRP. To do so, unplug phone from PC and press Power On and Volume Up simultaneously.
Download links for installing custom recovery TWRP for UHANS A101S:
Download from Mediafire
(For the recovery.img file, choose DRV.TEST version if you see this appendix in your firmware version. Otherwise, option v3.05 is correct).
If you want to restore stock recovery, recovery image from firmware version 3.05 is available too.
To install custom ROM, download your preferred ROM, copy it to your phone and flash from within TWRP.
Custom ROMs for UHANS A101S:
CLEAN MOD (Stock ROM without bloat)
MOKEE ROM (Gapps: no, root: no)
Resurrection Remix 5.7.4 (Gapps: no, root: yes)
To get Google Play store, flash Gapps package.
Download Gapps package here (choose ARM and Android 6.0):
http://opengapps.org
(Pico or Nano package recommended).
If you want root access and if it's not included in the ROM, you can flash SuperSU Zip using TWRP:
SR2-SuperSU-v2.79-SR2-20170103215521.zip
Stock ROM from UHANS (via SP Flash Tool):
https://mega.nz/#F!lX5BGKJS!pVksNANFfS2R8Jrpy6O1XQ
Source: http://www.uhans.cc/Service/index
A new custom rom
Hey guy! Thanks for your ROMs, I have Uhans A101S and they worked properly but I wanted to try something else with a google stock experience and so I wanna ask you if you can create another custom ROM (like lineage os) for this device.
Thanks a lot!
Related
Dear Friends,
Here is a new AOSP ROM with pure Lolipop Experience for our Lenovo A6000/Plus.
You need to be on official Lolipop, If you are still on Kitkat DONT FLASH IT.
First update your device toLolipop using Official OTA. Please explore XDA for "How to upgrade A6000/Plus to Lolipop"
Always a good Idea to take backup of device, including Modem, EFS, Radio etc if you may.
Downloads: :good::good::good:
ROM
GAPPS Use ARM 64 5.1.1 packages depending on your preference (Nano Gapps will do if you dnt want to install google apps as system apps)
TWRP Recovery TWRP-1 TWRP-2
Superuser
Steps to Install:
(If you are a noob PLEASE explore XDA before commenting here that this ROM bricks the phone, my phone is dead etc. If you are flashing ROM for the first time.. then it takes a lot of learning, Use YouTube, Google to learn about Custom Recovery, Super User etc)
Transfer ROM GAPPS and SuperUser Files to Your SD CARD.
Proceed for Recovery Installation.
1. Install TWRP .img File. (TWRP is a custom recovery which replaces your stock recovery)
Steps to install TWRP Recovery
a) Install Minimum ADB and Fastboot on Your PC along with USB Drivers for your Phone. XDA Link for Help
b) Rename the recovery file to "recovery.img" (You will need the name to build command line.)
c) Copy recovery.img file to the same folder where ADB is installed.
d) Connect android to PC via USB and enable USB debugging from Developer Options, Authorize USB debigging.
e) Open ADB application as administrator, Give command "adb devices", this will ask for USB debugging authorization, give that.
f) run following commands:
adb reboot bootloader
fastboot flash recovery recovery.img
fastboot boot recovery.img
More Help
You will be now on TWRP screen
1. Select Install > SuperUser
2. Wipe Data and cache
3. Select Install > ROM ZIP File (Add More Zips) Select GAPPS ZIP File.
4. Swipe to Flash.
5. Wait till it completes
6. Reboot, Be patient first boot takes time.
7. Setup Your Phone and you are good to Go.
Bugs : None Known.
GPS Working, SIM Cards Working, FM Radio Working, Hindi and Indian languages Working, Camera Working, Performance Good, Gaming Smooth, Battery drain Normal.
If you face any bug, please report.
NOOBS : Please dont comment I am DEAD, I am Bricked blah blah.. That not because of ROM, thats because you have not done enough study and not learned how to flash ROMs.
Screenshots: :cyclops::cyclops::cyclops:
Duplicate of Pure AOSP 5.1.1. Stable Rom for Lenovo A6000/Plus 64 BIT Version (Step by step Guide)
closed.
In order to keep this thread clean, please use this one to discuss about Development, Support or Software Updates.
ROMs:
To avoid any possible issue, do not forget to backup your NVRAM so that you won't risk to lose your IMEI. How-to: http://www.anythingultimate.in/2015/11/how-to-backup-your-nvram-partition.html
Stock (Android 6.0)
- V3.03: https://mega.nz/#!TYMyTA5Y!humI30xK0HIz1y5WfnALlK72AAiOtb4NiRzn3y2Fgqs
DO NOT USE THE "Format All & Download" OPTION IF YOU CARE ABOUT YOUR IMEI! Choose "Download Only" instead.
Previous Releases:
- Not yet.
Flash Tool
- SP Flash Tool v5.1628 for Windows & Linux: https://mega.nz/#F!dYUm0TbB!SWeMLb5Wu1NbRzTPQ8-s_A
Recovery:
- TWRP 3.0.3: https://forum.xda-developers.com/showpost.php?p=70546519&postcount=5
Root:
Rooting Methods (if you are on Stock ROM)
- SuperSU (flashable using TWRP): http://forum.xda-developers.com/apps/supersu
Extras (Root-Only):
Customization
- Xposed Framework: http://forum.xda-developers.com/showthread.php?t=3034811
Useful Third-Party Apps:
Battery Life
- Amplify: https://play.google.com/store/apps/details?id=com.ryansteckler.nlpunbounce&hl=en
- Greenify: https://play.google.com/store/apps/details?id=com.oasisfeng.greenify&hl=en
Thanks Alberto, i managed to build a TWRP and a CTR recovery for U300.
Unfortunately TWRP have no working touch because of a kernel issue, but you can use OTG mouse to work on this... Later i will try with latest 3.03 rom and share with community. Regards
megthebest said:
Thanks Alberto, i managed to build a TWRP and a CTR recovery for U300.
Unfortunately TWRP have no working touch because of a kernel issue, but you can use OTG mouse to work on this... Later i will try with latest 3.03 rom and share with community. Regards
Click to expand...
Click to collapse
For @jemmini : another device with the same touch issue.
U300 CTR and TWRP recoveries:
https://mega.nz/#!iUdTUb7D!PNZQSPwS3psOWxzBa79AB1qbJ2Si7Qh3aQTUwVmEsww
Download and Install correctly Mediatek Preloader drivers before using Flashtool
( Take care on Windows 8.1/10 drivers, you need to disable driver signature before install
https://www.youtube.com/watch?v=50pD0mONm44
http://laurentiumihet.ro/technology...-for-32-64-bit-drivers-installation-tutorial/
https://thebroodle.com/microsoft/windows/install-mediatek-mt65xx-usb-vcom-drivers-windows-8-8-1/
Pre Requisite: Unpack all files in a directory on desktop;
- Rename U300 Carliv CTR.img into Recovery.img (if you wanto to flash CTR recovery)
- Rename U300TWRP 3.02 No Touch.img into Recovery.img (if you wanto to flash TWRP recovery, but remember that you need OTG Mouse to use this recovery)
1- With flashtool load MT6750_Android_Scatter.txt
2- Select download and connect smartphone to pc (smartphone must be powered off)… in few seconds will start the process and the new CTR/TWRP will be flashed
P.S after flashing, enter immediately in CTR/TWRP at boot using POWER and VOL + keys at the same time until Logo; it will appear a text menu with 3 options, choose Recovery (first row) with vol- and wait the loading of Custom Recovery.
Please NOTE that CTR recovery could access internal memory that is named ExtraSD (so in install menu, choose zip from ExtraSD).
Move in CTR Recovery with Vol+ and Vol - and confirm with Power key.
Credits: [MENTION]carliv[/MENTION], @jemmini
TWRP 3.0.3 for UHANS U300
TWRP 3.0.3 for UHANS U300
Based on Android 6.0 firmware ver.DK9FA2FWTAG.HSA.UHANS.HB.F.SA.0105.V3.03 / Thu Jan 5 20:12:17 CST 2017
WARNING!! Strictly follow these installation instruction!
Install:
1. Flash the recovery.img using SP FlashTool
2. Enter into TWRP and Install the patch "SuperSU 2.79"
3. Reboot to the system
Thanks for sharing
Main Thread (with reviews and so on) has been replaced: https://forum.xda-developers.com/ge...ans-u300-information-reviews-5-5-fhd-t3555430
thanks
System.IMG Repack
In order to customized my UHANS U300, I already unpack and repack my System.IMG with various software, tools, script, Cygwin, android kitchen, Assayed Kitchen and also through Linux Mint and Lubuntu... but my phone stuck during boot. (Only display boot image from logo.bin). I believe my repack System.IMG's size was correct but the phone still stuck, and checksum failed. (I disable checksum by change switch from "1" to "0".
Can anybody help me, how to get rid of these?
Thanks in advance guys.
I bought it off ebay cheap (for £35) even though it's almost £200 on gearbest etc. I don't think people would want to clone this phone but wondered how it could be that cheap. My kernel version: 3.18.22 is this the latest update for the phone? I did a factory reset since when I got it it was already set up (even though sold as new) I could see an after-image of the Chinese seller so wanted to be safe rather than sorry. Hope someone can help in getting the most out of this phone/remove bloatware etc and how to check everything's ok?
Also any way to upgrade Android?
Ported TWRP recovery, only USB-OTG/adb/external SD card not working while inside TWRP. The rest is working fine.
Root obtained tested with all functions working with SuperSU 2.82 flashable zip.
TWRP: Flash this with SP Flashtool v5.1720 "Download only" mode
http://bit.ly/l551twrp
Messed it up and need the stock ROM?
http://bit.ly/l551stock
SP Flashtool 5.1720
http://bit.ly/spft51720
Latest Mediatek All in one USB Flash/ADB/CDC Driver package (Required to flash)
http://bit.ly/mtkdriveraio51632
Summary of instructions
Install drivers, extract flash tool, extract TWRP flash package zip, open flashtool.exe, point “Scatter-loading file” to file containing the word “scatter” located in TWRP flash package extracted folder. After scatter loads, you may uncheck all files except recovery inside SP Flashtool. Please make sure the mode is “Download only” from pull down menu. Press the green download arrow icon then plug in the unit from a completely off state.
It works good, thanks.
Help my plz
I want a rout to phone posh l551
******TWRP 3.1.0 FOR M10 CHINAPHONE******
---------------------------------------------------------------------------
DISCLAIMER : this is an unnoficial build created by myself Tested and confirmed working
NOT WORKING : MTP
THIS IS FOR EXT4 ONLY IF YOU NEED UBIFS OR YAFFS2 RECOVERY COMMENT HERE I WILL BUILD YOU ONE AGAIN EXT4 ONLY...
_______________________________________________
NOTICE : take a firmware backup before flashing
Anything to your device though this recovery is
Confirmed working you should always back your original firmware up, This recovery does NOT come with a Scatter.file included to stop bricking with incompatible device partitions
--------------------------------------------------------------------------
1. Unzip the recovery from the .zip.
2. Open SP Flash tool.
3.set your DA AGENT to all in one MTK DA.
4.load your scatter.file into the Flash tool.
5.wait for your scatter to load your files.
6.unselect all files for flash but recovery.
7.load twrp_3.1 into recovery slot.
7.1 flash my patched boot.img below also.
8.MAKE SURE DOWNLOAD ONLY is set DO NOT use format all + download.
9. Click start button
10. Connect to pc with usb cord.
12. wait for flash to complete.
13. Unplug & take out & insert your battery.
14. Hold power & volume up until the first screen appears and release, TWRP will now load.
15. Swipe to allow modifications.
Thats it Happy Flashing dont forget the thanks button & enjoy
---------------------------------------------------------------------------
If you need help please dont be afraid to ask here im here to help, if it does not boot on your device your board is different in which case you will need to attach your boot.img & recovery.img in a post so i can download and create a compatible twrp for your device.
_____________________________________________
LINKS :
TWRP 3.1.0
https://drive.google.com/file/d/1yhFWmbTUQLFvJCGZnUX20oF-f6TTEBaX/view?usp=drivesdk
Patched Boot.img : will be up later
Removed the following.
*SB.CHK
*Encrypted footers on userdata from :
*fstab
*fstab.fat
* fstab.fat.nand,
*adjusted kernel slightly this will not affect the operation of the system or operation of it.
[ROOT] Galaxy J810x Methods Magisk And Twrp
[ROOT Normaly]
1. Download Stock ROM 9.x or upgrade normaly
2. Start your ROM enter configuration, developer options and set Unlock by OEM
3. Download Odin 3.14 and drivers
4. Download Magisk and TWRP 3.3.0 and no-verity-opt-encrypt-6.1.zip
5. Install drivers for J7
6. Copy Magisk and no-verity-opt-encrypt-6.1.zip to SD Card
7. Enter in Stock Recovery and Factory reset
[Download MODE]
8. After this enter in download mode imediatly or your system encrypt
9. no start your stock rom or your system encrypt
10. Open Odin 3.14 flash Stock Bootloader and Modem Only If necessary
11. Flash TWRP with Odin or upgrade via img
12. Reboot imediatly in Recovery
13. Flash Magisk 20
14. Flash no-verity-opt-encrypt-6.1.zip
15. iNTALL your prefered Custom ROM
16. Install Magisk Manager 7.5
17. Press Thanks please
18. in this moment install Havoc or Lineage 17.1
[mAgisk mEthod]
You will need the stock Rom files from Sammobile for your phone model(BL, AP, CP, HOME CSC) and Odin on your PC.
1. Install Magisk manager on your phone.
2 Copy the AP file on your Download folder of your phone.
3 Open Magisk and tap Install Magisk then Select and patch a file. Go on Download folder and select the AP file to patch. After is done it will create a file in your Download folder named magisk_patched.tar. Copy this file back on your PC.
4 Run Odin and put your phone on Download mode. To get in Download mode shut your phone off, Hold pressed VOLUME UP + POWER, select Reboot to bootloader.
5 In Odin select BL, CP and Home_CSC from your stock ROM folder. In AP select the magisk_patched.tar file. Go on Optons and uncheck Auto Reboot. Hit START and let him finish. IMPORTANT, READ FIRST : After is done you have to restart the phone by pressing VOLUME DOWN + POWER and when the screen is black immediately press VOLUME UP + POWER. Dont let go until you are in Recovery mode, even if restarts.
5 select Wipe data/ factory reset and then Reboot system now. Might take a while to boot.
6 Set up your phone and install Magisk Manager again. It will ask you to complete the rooting will need to install few more files. Press OK.
WELL DONE. You have root now.
[RECOVERY][UNOFFICIAL]TWRP 3.3.1-0 Galaxy J8 J810M/F/FN/G/DS
https://forum.xda-developers.com/an...overy-twrp-3-3-1-0-galaxy-j8-j810m-f-t3962423
[Magisk 20.4] Primary option
https://github.com/topjohnwu/Magisk/releases/download/v20.4/Magisk-v20.4.zip
[Manager 7.5.2]
https://www.apkmirror.com/apk/topjohnwu/magisk-manager/magisk-manager-7-5-2-1e2de1bb-release/
[no-verity-opt-encrypt-6.1.zip]
https://build.nethunter.com/android-tools/no-verity-opt-encrypt/
[Official]
Magisk Official Post
https://forum.xda-developers.com/apps/magisk/official-magisk-v7-universal-systemless-t3473445
[RMM State Fix] Miracle box
https://forum.xda-developers.com/ga...-rmm-fix-oreo-8-1-oem-unlock-fix-dez-t3877764
The Secret Of My Seccess is Jesus
Since you mentioned custom ROMs in the first guide, have you found any that are compatible with the J8? If so, could you link them?
Edit: Found a port of LineageOS 16 (Android 9.0) by the developer Bad Guy. However I couldn't get TWRP to flash it as it always resulted in error 7, despite modifying the file to remove the assert section. The no-verity-opt-encrypt-6.1.zip would not flash either due to error 1.
Someonerandom said:
Since you mentioned custom ROMs in the first guide, have you found any that are compatible with the J8? If so, could you link them?
Edit: Found a port of LineageOS 16 (Android 9.0) by the developer Bad Guy. However I couldn't get TWRP to flash it as it always resulted in error 7, despite modifying the file to remove the assert section. The no-verity-opt-encrypt-6.1.zip would not flash either due to error 1.
Click to expand...
Click to collapse
Hello my friend
technically j8 has a native treble and means that any treble ROM can be installed on the j8 with a custom kernel
If You have time test this ROM
https://forum.xda-developers.com/ga...om-crdroid-6-3-android-q-10-0-galaxy-t4048917
You need Kernel Android 10
Remember backup your files
Unlock oem and USB debugg
hacker812c said:
Hello my friend
technically j8 has a native treble and means that any treble ROM can be installed on the j8 with a custom kernel
If You have time test this ROM
https://forum.xda-developers.com/ga...om-crdroid-6-3-android-q-10-0-galaxy-t4048917
You need Kernel Android 10
Remember backup your files
Unlock oem and USB debugg
Click to expand...
Click to collapse
I have taken a look at your ROM, however I don't think it would work.
The ROM is ARM64, and the Galaxy J8 is an ARM device with a 64-bit binder. This means that the ROM needs to have that architecture to work.
It also requires Spaget X which is built for Exynos, and the J8 is a Snapdragon device.
And on another note, do you happen to know the fix for error 1 on the disable forced encryption zip?
Someonerandom said:
I have taken a look at your ROM, however I don't think it would work.
The ROM is ARM64, and the Galaxy J8 is an ARM device with a 64-bit binder. This means that the ROM needs to have that architecture to work.
It also requires Spaget X which is built for Exynos, and the J8 is a Snapdragon device.
And on another note, do you happen to know the fix for error 1 on the disable forced encryption zip?
Click to expand...
Click to collapse
Yes
If j8 use custom kernel 10
You install any release treble
I have release arm and arm64
Can i do that with android 8?
J810F android 8 or 10 working ???