Database Info

Cherry mobile Omega HD (i-mobile IQ6)

Omega HD root
Disclaimer: I will not be liable for bricked devices. Follow these instructions at your own risk. ROOTING VOIDS WARRANTY, as per Cherry Mobile. Please be guided accordingly.
This tutorial is not recommended for newbies. Knowledge of basic adb and fastboot commands is helpful. Better if you have previously installed ADB drivers.
Downloads (http://www.mediafire.com/?ar2ccya8395d1):
SuperSU zip
TWRP
SP Flash Tool
MTK Drivers
MTK 6577 scatter file
if the driver didn't work download this http://www.4shared.com/zip/YXlLFoLm/6577driver_install_3_steps.html
install folder step 1 to 3
Place the scatter file and TWRP recovery in the SAME FOLDER.
rename twrp recovery to recovery.img
1. While the phone is still on, enable USB debugging (Settings > Developer options) then plug into PC. Allow drivers to install. Install the MTK drivers as well.
2. Mount phone as USB storage. Copy SuperSU zip to internal or external SD card. Unmount USB storage, then unplug phone from PC.
2. Turn off phone. Remove the battery.
3. Start SP Flash Tool. Under "Scatter-loading," choose the MT6577_Android_scatter_emmc.txt. You will see that RECOVERY has a check beside it. Click on "Download." A warning will appear, proceed anyway.
4. With your phone still off and the battery out, plug it in to the PC. Flashing should start. It will only take a few seconds. You'll see a green circle when it's done.
5. Unplug USB cable and put the battery back.
6. Enter recovery mode by Power and Volume + button. Release both buttons when you see the boot menu. Use Volume + to highlight "recovery." Then use Volume - to confirm.
7. Click "Install." Choose the appropriate tab (internal or external SD card).
8. Select UPDATE-SuperSU-1.25 zip. Swipe to confirm the update. It will flash. Go back to main menu of TWRP.
9. Click "Reboot system." Wait until you are fully booted into your homesceen.
10. Once booted, you should see SuperSU in your app drawer.
credits to ish gridote
OmegaXtremeHD
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
s3 bootanimation n sound
s3 boot logo
Jelly bean icons
iphone ringtones
google play music
dolphin browser
apex launcher
deodexed
busybox
rooted
init.d
signal tweaks
3g tweaks
battery tweaks
gpu rendering
dns tweaks
media tweaks
v6 supercharger
kickasskernel
crossbreeder
reorganized build.prop file
uploading
http://www.4shared.com/folder/dJXI2ODd/_online.html
try open first in case of corrupt file
remove crossbreeder for much better battery
flash uninstall zip http://forum.xda-developers.com/showthread.php?t=2113150
and underclock for much longer battery download setcpu or no frillcpu or anything u want i dnt care..
save rom in SD card
reboot to CWM/TWRP
install rom via SD card
reboot
I'm not responsible for any loss of data or brick....
i think this only works on iq6A

do you already own this phone?

Cherry mobile Omega HD info states that its a dual core phone while all info about i-mobile IQ6 states its a single core phone. does anyone know which mediatek chipset the Omega HD uses? It's GPU?

yes i had it

How?
How can we flash the CWM to the Omega HD if you don't even give us a flashtool? Is this Rooting process tested? is it working?

Please help me
Wil53664 said:
yes i had it
Click to expand...
Click to collapse
Sir, can I have a copy of the Setting.apk of your Cherry Mobile HD? i've accidentally forgot to have a backup of it and now, i've accidentally just erased it. please help me. thankyou very much

Pretty Please?
Wil53664 said:
yes i had it
Click to expand...
Click to collapse
please post the Settings.apk of the Cherry Mobile Omega HD sir. I really need it it would be appreciated if you post it here.

How to Backup the phone
just bought the phone yesterday
do yo guys know how to back up this jellybean phone?

Hey guys, if you have FB we have a group with most of oHD users. Just search "CherryMobileOmegaHD" in FB (can't post links yet. sorry)
There are custom roms in the group, the usual rom cooked from dsdixda's kitchen (zipalign, deodexed, rm bloatwares)
@cyzarine
What do you mean with backup? We have the stock rom in the group, you might want to check it out.

Bummer! I'm stuck at step 3!
You will see that RECOVERY has a check beside it. Click on "Download." A warning will appear, proceed anyway.
Click to expand...
Click to collapse
-- umm... NO, I DON'T!! There must be a step that's missing... :-S
edit:
nevermind. I forgot to rename TWRP file to "recovery"
Thanks for this!

anyone have a kernel that have oc"?

In need...
Woke up to a drained Omega HD today.
Plugged it in to have it charged.
Switched it on afterwards.
"OmegaHD" flashed before my eyes, followed by a blank screen with the familiar Cherry Mobile tune playing on the background. And then nothing! NO DISPLAY! I touch the screen and there are sounds playing to confirm each press, which means I am pressing on the right places -- only that there is NO DISPLAY APPEARING.
I switch it on and off, still the same results.
Wiped cache. Nothing... Since it's practically new, I go ahead and factory-restore the thing... still the same results. NO DISPLAY! :-S
What else can I do to this device to have it work properly?!

Have you installed any custom rom or any other zip files with your phone?

xMinistro said:
Have you installed any custom rom or any other zip files with your phone?
Click to expand...
Click to collapse
do have stock rom can you give plsss......

---------- Post added at 11:02 PM ---------- Previous post was at 10:41 PM ----------
[/COLOR]
Wil53664 said:
Omega HD root
Disclaimer: I will not be liable for bricked devices. Follow these instructions at your own risk. ROOTING VOIDS WARRANTY, as per Cherry Mobile. Please be guided accordingly.
This tutorial is not recommended for newbies. Knowledge of basic adb and fastboot commands is helpful. Better if you have previously installed ADB drivers.
Downloads (http://www.mediafire.com/?ar2ccya8395d1):
SuperSU zip
TWRP ported by me
SP Flash Tool
MTK Drivers
MTK 6577 scatter file
if the driver didn't work download this http://www.4shared.com/zip/YXlLFoLm/6577driver_install_3_steps.html
install folder step 1 to 3
Place the scatter file and TWRP recovery in the SAME FOLDER.
rename twrp recovery to recovery.img
1. While the phone is still on, enable USB debugging (Settings > Developer options) then plug into PC. Allow drivers to install. Install the MTK drivers as well.
2. Mount phone as USB storage. Copy SuperSU zip to internal or external SD card. Unmount USB storage, then unplug phone from PC.
2. Turn off phone. Remove the battery.
3. Start SP Flash Tool. Under "Scatter-loading," choose the MT6577_Android_scatter_emmc.txt. You will see that RECOVERY has a check beside it. Click on "Download." A warning will appear, proceed anyway.
4. With your phone still off and the battery out, plug it in to the PC. Flashing should start. It will only take a few seconds. You'll see a green circle when it's done.
5. Unplug USB cable and put the battery back.
6. Enter recovery mode by Power and Volume + button. Release both buttons when you see the boot menu. Use Volume + to highlight "recovery." Then use Volume - to confirm.
7. Click "Install." Choose the appropriate tab (internal or external SD card).
8. Select UPDATE-SuperSU-1.25 zip. Swipe to confirm the update. It will flash. Go back to main menu of TWRP.
9. Click "Reboot system." Wait until you are fully booted into your homesceen.
10. Once booted, you should see SuperSU in your app drawer.
credits to ish gridote
Click to expand...
Click to collapse
Hi. Can you please post a mirror on the twrp-omegahd.img file? All of the other files have been downloaded except for the img file. Error comes up.

bakes5981 said:
Bummer! I'm stuck at step 3!
-- umm... NO, I DON'T!! There must be a step that's missing... :-S
edit:
nevermind. I forgot to rename TWRP file to "recovery"
Thanks for this!
Click to expand...
Click to collapse
please hit thanks if this helps

OmegaXtremeHD link issues
OmegaXtremeHD link is not working .... 509 error .... any mirror or alternative links?

Wil53664 said:
Omega HD root
Disclaimer: I will not be liable for bricked devices. Follow these instructions at your own risk. ROOTING VOIDS WARRANTY, as per Cherry Mobile. Please be guided accordingly.
This tutorial is not recommended for newbies. Knowledge of basic adb and fastboot commands is helpful. Better if you have previously installed ADB drivers.
Downloads (http://www.mediafire.com/?ar2ccya8395d1):
SuperSU zip
TWRP ported by me
SP Flash Tool
MTK Drivers
MTK 6577 scatter file
if the driver didn't work download this http://www.4shared.com/zip/YXlLFoLm/6577driver_install_3_steps.html
install folder step 1 to 3
Place the scatter file and TWRP recovery in the SAME FOLDER.
rename twrp recovery to recovery.img
1. While the phone is still on, enable USB debugging (Settings > Developer options) then plug into PC. Allow drivers to install. Install the MTK drivers as well.
2. Mount phone as USB storage. Copy SuperSU zip to internal or external SD card. Unmount USB storage, then unplug phone from PC.
2. Turn off phone. Remove the battery.
3. Start SP Flash Tool. Under "Scatter-loading," choose the MT6577_Android_scatter_emmc.txt. You will see that RECOVERY has a check beside it. Click on "Download." A warning will appear, proceed anyway.
4. With your phone still off and the battery out, plug it in to the PC. Flashing should start. It will only take a few seconds. You'll see a green circle when it's done.
5. Unplug USB cable and put the battery back.
6. Enter recovery mode by Power and Volume + button. Release both buttons when you see the boot menu. Use Volume + to highlight "recovery." Then use Volume - to confirm.
7. Click "Install." Choose the appropriate tab (internal or external SD card).
8. Select UPDATE-SuperSU-1.25 zip. Swipe to confirm the update. It will flash. Go back to main menu of TWRP.
9. Click "Reboot system." Wait until you are fully booted into your homesceen.
10. Once booted, you should see SuperSU in your app drawer.
credits to ish gridote
OmegaXtremeHD
s3 bootanimation n sound
s3 boot logo
Jelly bean icons
iphone ringtones
google play music
dolphin browser
apex launcher
deodexed
busybox
init.d
signal tweaks
3g tweaks
battery tweaks
v6 supercharger
kickasskernel
crossbreeder
download link
https://www.dropbox.com/s/8q1c6db45uegepk/OmegaXtreme.zip
updated link
save rom in SD card
reboot to CWM/TWRP
WIPE DATA/FACTORY RESET
install rom via SD card
reboot
Click to expand...
Click to collapse
Hey buddy,
Where's the file..??

StanleyD said:
Hey buddy,
Where's the file..??
Click to expand...
Click to collapse
will update link later

having trouble with some apps working on my Omega HD. a couple of my Android mainstays are Haxsync and Swiftkey. on my Omega HD, they run no problem, but if the unit powers off for whatever reason, when I turn it back on, my Haxsync account (under Settings/Accounts) disappears, requiring me to set up the app again, and Swiftkey is no longer activated as my default input. any help?

ClocworkMod recovery for XOLO A500

Hi,
XDA world....Another post by me for XOLO A500 users.
This post will help you to install Clockworkmod recovery on your xolo a500.
First and the foremost thing you need is a rooted device.If you haven't rooted your device please root it. Refer the following link on how to root your lava xolo a500.
http://forum.xda-developers.com/showthread.php?p=39358817
Now download the XOLO A500 CWM Toolkit from download link given in the last.
1.) Extract the rar file to a folder anywhere on your computer.
2.) Open the folder and press shift key and right click(holding down the shift key) anywhere on the blank space of the screen and select "Open Command window here".
3.) You will see a command prompt window on the screen.
4.) Now connect your device via usb cable and enable usb debugging(Settings->Development->USB Debugging )
5.) Now Download the Quick Boot App from play store & install it in your Mobile. Open that App & click on Bootloader option.
6.) After sometime your phone will get stuck at the logo. (don’t panic)
7.) Now type on the cmd window:
fastboot devices(press enter)
fastboot flash recovery recovery.img
Within a sec the process will get over & it will install the cwm recovery on you Xolo A500
So Enjoy, you have successfully installed CWM Recovery on your Xolo A500..
Now you can check whether your CWM is working or not:-
---Remove battery of your phone and reinsert.
---Press Power and Volume down key to boot into recovery mode.
Congrats, You have successfully installed Cwm 6 in your Lava A500
But there is a bug in this recovery that is not yet fixed. The bug is that when you boot your device into recovery mode the user language is Chinese...But not to worry...
Ignore the recovery mode...
Go to play store and download ROM Manager by clockworkmod.It has all the features which the recovery menu should be having.
1.) Open ROM Manager
2.) Go to Install Clockworkmod recovery.
3.) Scroll down to the last and you will see Device not listed option.Open it.
4.) A prompt will come.Press yes. And then choose option 3.x+ option.
And now you are ready to use your CWM Recovery on ROM Manager.

Problem with installing CWM
Hi
Problem with installing CWM on my XOLO A500. When I Click quickboot booloader option it shows up an android logo with text “DOWNLOADING.. PLEASE DONT TURN OFF THE TARGET”
and hangs. Please HELP ASAP. THANKS

dhruba.sarma said:
Hi
Problem with installing CWM on my XOLO A500. When I Click quickboot booloader option it shows up an android logo with text “DOWNLOADING.. PLEASE DONT TURN OFF THE TARGET”
and hangs. Please HELP ASAP. THANKS
Click to expand...
Click to collapse
I have clearly mentioned that when you press bootloader option
DOWNLOADING.. PLEASE DONT TURN OFF THE TARGET
Click to expand...
Click to collapse
will appear.
As soon as you see this screen just type on the cmd window:
fastboot devices(press enter)
fastboot flash recovery recovery.img
This will successfully install CWM recovery.
Remove battery of your phone and reinsert.
---Press Power and Volume down(Please donot press volume up button) key to boot into recovery mode.

I'm unable to open command window through pressing the "Shift key+Right click" . Do yu have any vedio tutorial. Help me,..

Answer to your question.
GauravBak said:
I'm unable to open command window through pressing the "Shift key+Right click" . Do yu have any vedio tutorial. Help me,..
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hope it helped you.
If I helped Please Hit Thanks.

but when i type the word "fastboot devices" then press enter and after that i type "fastboot flash recovery recovery.img" and enter, it says waiting for device.. nothing happen,..!
I'm using windows-xp

same problem.. stuck at waiting for devices on the cmd prompt. My device is already connected to pc and usb debugging mode is on

HELP,...

Procedure TO Install NEW ROM on XOLO A500
GauravBak said:
Plz buddy give me a tutorial about how to flash a ROM in my XOLO A500, I have installed CWM+ROM Manager and have TBMk5 ROM.zip in my SD card, a picture tutorial is very helpful.
Click to expand...
Click to collapse
Procedure TO Install NEW ROM on XOLO A500
1 First go to Cwm recovery by pressing power+volume down (-) key
2 then wipe data/factory reset
3 wipe cache partition
4 go to "advanced"
5 & wipe dalvik cache & wipe battery stats
6 then go back
7 & select 2nd option install zip from sd card & locate the zip ,,,, then follow the procedure & u will get new rom installation by aroma installer
8 then reboot system & wait beacause initialisation takes few minutes ... enjoy!!! reboot is necessary
NOTE:- for selecting any option press power key & to scroll by volume keys
,, check sd card is mounted or not ,, if not mount by "mounts and storage" option
please hit thanks as it helped you..
for any query visit my account or just reply:good::good:

Recovery Mode not opening..
Hii..
I have installed cwm on my phone..
but now i am not able to open the recovery mode by pressing volume up+power..:crying::crying::crying:
i tried both volume up & down with Power key combination..!!
so plz help me n tell me how to get back my original recovery mode..!!
ThanXX a Lot In AdvAnce..!!

its in chinese dude
the recovery menu is in chinese ......pls help

thanks
I read and review this , thanks.

thanx alot for helping

problems while flashing cwm.. plz help
Ishan16 said:
Hi,
XDA world....Another post by me for XOLO A500 users.
This post will help you to install Clockworkmod recovery on your xolo a500.
First and the foremost thing you need is a rooted device.If you haven't rooted your device please root it. Refer the following link on how to root your lava xolo a500.
http://forum.xda-developers.com/showthread.php?p=39358817
Now download the XOLO A500 CWM Toolkit from download link given in the last.
1.) Extract the rar file to a folder anywhere on your computer.
2.) Open the folder and press shift key and right click(holding down the shift key) anywhere on the blank space of the screen and select "Open Command window here".
3.) You will see a command prompt window on the screen.
4.) Now connect your device via usb cable and enable usb debugging(Settings->Development->USB Debugging )
5.) Now Download the Quick Boot App from play store & install it in your Mobile. Open that App & click on Bootloader option.
6.) After sometime your phone will get stuck at the logo. (don’t panic)
7.) Now type on the cmd window:
fastboot devices(press enter)
fastboot flash recovery recovery.img
Within a sec the process will get over & it will install the cwm recovery on you Xolo A500
So Enjoy, you have successfully installed CWM Recovery on your Xolo A500..
Now you can check whether your CWM is working or not:-
---Remove battery of your phone and reinsert.
---Press Power and Volume down key to boot into recovery mode.
Congrats, You have successfully installed Cwm 6 in your Lava A500
But there is a bug in this recovery that is not yet fixed. The bug is that when you boot your device into recovery mode the user language is Chinese...But not to worry...
Ignore the recovery mode...
Go to play store and download ROM Manager by clockworkmod.It has all the features which the recovery menu should be having.
1.) Open ROM Manager
2.) Go to Install Clockworkmod recovery.
3.) Scroll down to the last and you will see Device not listed option.Open it.
4.) A prompt will come.Press yes. And then choose option 3.x+ option.
And now you are ready to use your CWM Recovery on ROM Manager.
Click to expand...
Click to collapse
the message showing on phone screen is "partition 'recovery' not support flash"...
plz tell how to fix it...

I have the perfectly working English cwm image
Sent from my A500 using XDA Premium 4 mobile app

same problem.. stuck at waiting for devices on the cmd prompt.

Ishan16 said:
I have clearly mentioned that when you press bootloader option will appear.
As soon as you see this screen just type on the cmd window:
fastboot devices(press enter)
fastboot flash recovery recovery.img
This will successfully install CWM recovery.
Remove battery of your phone and reinsert.
---Press Power and Volume down(Please donot press volume up button) key to boot into recovery mode.
Click to expand...
Click to collapse
What to do after pressing power + volume down button as further it is chineese menu.
Please reply
---------- Post added at 06:40 AM ---------- Previous post was at 06:04 AM ----------
Ishan16 said:
Hi,
XDA world....Another post by me for XOLO A500 users.
This post will help you to install Clockworkmod recovery on your xolo a500.
First and the foremost thing you need is a rooted device.If you haven't rooted your device please root it. Refer the following link on how to root your lava xolo a500.
http://forum.xda-developers.com/showthread.php?p=39358817
Now download the XOLO A500 CWM Toolkit from download link given in the last.
1.) Extract the rar file to a folder anywhere on your computer.
2.) Open the folder and press shift key and right click(holding down the shift key) anywhere on the blank space of the screen and select "Open Command window here".
3.) You will see a command prompt window on the screen.
4.) Now connect your device via usb cable and enable usb debugging(Settings->Development->USB Debugging )
5.) Now Download the Quick Boot App from play store & install it in your Mobile. Open that App & click on Bootloader option.
6.) After sometime your phone will get stuck at the logo. (don’t panic)
7.) Now type on the cmd window:
fastboot devices(press enter)
fastboot flash recovery recovery.img
Within a sec the process will get over & it will install the cwm recovery on you Xolo A500
So Enjoy, you have successfully installed CWM Recovery on your Xolo A500..
Now you can check whether your CWM is working or not:-
YOU JUST TELL ME HOW DO I GET MY ORIGINAL RECOVERY MENU BACK COZ IM GETTING VERY ANGRY NOW WITH THE CHINESE MENU. I DONT WANT ANY OTHER HELP.
PLEASE REPLY FAST.
---Remove battery of your phone and reinsert.
---Press Power and Volume down key to boot into recovery mode.
Congrats, You have successfully installed Cwm 6 in your Lava A500
But there is a bug in this recovery that is not yet fixed. The bug is that when you boot your device into recovery mode the user language is Chinese...But not to worry...
Ignore the recovery mode...
Go to play store and download ROM Manager by clockworkmod.It has all the features which the recovery menu should be having.
1.) Open ROM Manager
2.) Go to Install Clockworkmod recovery.
3.) Scroll down to the last and you will see Device not listed option.Open it.
4.) A prompt will come.Press yes. And then choose option 3.x+ option.
And now you are ready to use your CWM Recovery on ROM Manager.
Click to expand...
Click to collapse
JUST TELL ME HOW DO I GET MY NORMAL RECOVERY MENU BACK WITH ENGLISH COZ I AM VERY ANGRY NOW AND HATE THAT CHINESE MENU.REPLY FAST HOW TO GET RID OF THAT.

Sorry for the inconvenience caused.
Hey guys sorry for my late reply.
Those of you who are having problem in "Waiting for Device" please check that you have correctly installed adb drivers on your pc.
Still if you want you can try "Adb driver installer".
For the chinese menu issue please follow the below post by me.
http://forum.xda-developers.com/showthread.php?t=2349045
Press thanks if I helped.

Every thing went well still hadn't got CWM recovery
Ishan16 said:
Hi,
XDA world....Another post by me for XOLO A500 users.
This post will help you to install Clockworkmod recovery on your xolo a500.
First and the foremost thing you need is a rooted device.If you haven't rooted your device please root it. Refer the following link on how to root your lava xolo a500.
http://forum.xda-developers.com/showthread.php?p=39358817
Now download the XOLO A500 CWM Toolkit from download link given in the last.
1.) Extract the rar file to a folder anywhere on your computer.
2.) Open the folder and press shift key and right click(holding down the shift key) anywhere on the blank space of the screen and select "Open Command window here".
3.) You will see a command prompt window on the screen.
4.) Now connect your device via usb cable and enable usb debugging(Settings->Development->USB Debugging )
5.) Now Download the Quick Boot App from play store & install it in your Mobile. Open that App & click on Bootloader option.
6.) After sometime your phone will get stuck at the logo. (don’t panic)
7.) Now type on the cmd window:
fastboot devices(press enter)
fastboot flash recovery recovery.img
Within a sec the process will get over & it will install the cwm recovery on you Xolo A500
So Enjoy, you have successfully installed CWM Recovery on your Xolo A500..
Now you can check whether your CWM is working or not:-
---Remove battery of your phone and reinsert.
---Press Power and Volume down key to boot into recovery mode.
Congrats, You have successfully installed Cwm 6 in your Lava A500
But there is a bug in this recovery that is not yet fixed. The bug is that when you boot your device into recovery mode the user language is Chinese...But not to worry...
Ignore the recovery mode...
Go to play store and download ROM Manager by clockworkmod.It has all the features which the recovery menu should be having.
1.) Open ROM Manager
2.) Go to Install Clockworkmod recovery.
3.) Scroll down to the last and you will see Device not listed option.Open it.
4.) A prompt will come.Press yes. And then choose option 3.x+ option.
And now you are ready to use your CWM Recovery on ROM Manager.
Click to expand...
Click to collapse
Every thing went well even I saw Chinese recovery but now when I switch into recovery shows me android recovery instead of CWM recovery

For English recovery please follow the link given above your post.
Sent from my HTC Desire 310 dual sim

[ Auxus Nuclea N1 ] - All Things Thread

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Technical Specs
[*]Google it before posting here.
[*]Please post any guides and/or tutorials directly onto the forum, rather than links, otherwise this thread will be closed by the Moderator.
Click to expand...
Click to collapse
Rooting for 8GB Version
Procedure:
1. Download the Framaroot application and transfer it to SD card
2. Now go to Settings>Security and put check mark on Unknown Soruces
3. Now use file manager and browse to the location where you have placed Framaroot Application
4. Install it and open it. Now Select "Install SuperSU" and hit Boromir.
5. Now go to Play Store and search for Super User and install it after opening it might ask to update SU.bin, hit yes and then "Normal"
6. Reboot your Device.
[ROMs]​
Please do not flash the firmware that is not meant for your phone. Flash only 4gb to 4gb and 8Gb to 8Gb
Auxus Nuclea N1 Stock Firmware
NEW
Final Version - 11-Dec-2013 - [Flash with SPFlash Tools]
Click to expand...
Click to collapse
OLD ROMs
Firmware Update (Intermediate V1) 18-Nov-/2013 [Flash with spflash Tools]
NucleaN1_FirmwareUpdate_V1_CWM.zip
Click Here - - [09/Sep/2013] [Flash with SPFlash Tools]
CWM Zip Download from herehttp://d-h.st/b3r
8GB version -
Click Here - [Flash with SPFlash Tools]
Custom ROMs
Click HERE​
How to Flash Stock ROM using SP Flash Tools?​
1) Unzip the ROM folder
2) Install the drivers and open SP Flash Tools..
Check the below post with images, if you are not sure whether drivers are installed or not.
If you face this problem, then try Firmware upgrade and connect the phone..
You can now safely disconnect your phone and turn it on. The process ends here.
FLASHING PATCH using SP Flash Tool(Single Files)​
1)Select Android Scatter File .txt ....
2)Uncheck all files from the below box....
3)Select the correct file you want Flash by clicking it....
4)Click Download button on SP tool.... **"Dont click Firmware Upgrade"
5)A box asks to confirm it...Click Yes...
6)Connect Phone without the battery...
7)It will get Flashed...[/COLOR]
[Recovery]​
1) Nuclea N1 Stock Recovery Click Here
2) TWRP Recovery- Click HereThanks to Kumar abhishek
3) CWMRecovery 6.0.3.3 Click Here or Click Here Thanks to C3C076
Procedure to Flash Recovery.
1) Download Mobile uncle tools from play store
2) Place the downloaded recovery.img in your sdcard
3) Open Mobile uncle tools
4) Select 'update recovery' and Click on the recovery.img
5) Reboot
adb method: For advance users:
---------------------------------------------------
Make sure you have all the drivers for your phone installed on your computer.
Make sure you have USB Debugging enabled, Install from Unknown Sources is enabled and device is detected in ADB run this command:
Code:
adb devices
Download the CWM Recovery
Press SHIFT key + Right mouse click in the folder where the file is located and select Open Command from Here.
Now, in the command prompt do the following:
a. Reboot into Bootloader mode. Use command:
Code:
adb reboot bootloader
b. Device will reboot and display logo. (check if device is in bootloader mode by running command:
Code:
fastboot devices
. If you see a device connected then you have successfully rebooted into fastboot mode.
c. Now, run this command:
Code:
fastboot flash recovery recovery.img
(This will flash the CWM recovery image to the device).
d. Once successful, reboot the device using this command:
Code:
fastboot reboot
.​
How to Backup ur complete ROM
1. In CWM Recovery mode, select Backup and Restore
2. Select Backup
3. Wait till it finishes (May take upto 10 minutes)
How to restore ur backed up ROM from SD card
1. Go to CWM Recovery, select backup and restore
2. Select Restore
3. select the folder in date format (Folder name indicates the time and date when ur backup was created}
4. Wait till it finishes (May take upto 10-15 minutes)
Special Guides for Newbies to get Started​
Everything you need to know about Clockworkmod Recovery
How to setup ADB and Fastboot properly
5 Things Every Android user should do
24 Apps Every Android User Must Install
5 Things to know before performing any Android tweak
Thanks to Driodiser
HIT THANKS PLEASE BECAUSE IT WONT COST ANY :angel:

Extend your storage on Nuclea N1
[Extend your storage on Nuclea N1] - Thanks to @kailashnj
Follow the instructions in the post HERE​
How to enter into Recovery - Nuclea N1 :-
Code:
[LIST=1]
[*]Turn OFF your phone.
[*]Press & hold Vol(+) button and Power button for 12 seconds.
[B]Stock Recovery[/B]
[*]You will see a laid-down Android symbol with 'No command' message below it. Press the power button once.
[*]You will enter into menu 'Android System Recovery'
[*]Press Vol(-) to roll over options.
[*]Press Vol(+) button to select.
[*]DONE!
[/LIST]
Another options if you are facing trouble going to recovery:
Code:
1. Install Mobile Uncle tool
2. Reboot recovery.
MTK6589 Drivers
Universal Pdanet drivers Click Here
Follow this guide Here
Tools
MTK Android PC Sync Tool V2.1233.1 Click Here
SN_Write_tool_exe_v2.1132.0.rar - 8.27 MB
Guide Here
Driver_Auto_Installer_v1.1236.00 Click here

Meta-Mode is very useful if device fails to get detected by PC under normal Conditions.....To make device fall to Meta-Mode,just do these :
1) Start SP Tool on PC..
2) Now run SP Tool with "Firmware Upgrade/Download"
3) Switch OFF Phone..
4) Remove Battery..
5) Connect mobile to PC while holding Volume + button [WITHOUT BATTERY]..
6) Flashing will be started
7) Hold the button till flashing completes...
After 100% Flash,Release Button..
9) Insert Battery..
10) Start Device.
Click to expand...
Click to collapse
How to dump stock recovery image using SP Flash Tool
1) Download and install USB VCOM Driver
2) Download, extract and launch SP Flash Tool
3) Use "Scatter-loading" button to load attached scatter file: MT6589_Android_scatter_emmc.txt
4) Download stock recovery image and place inside the ROM folder. Then select only RECOVERY.
5) Turn off your phone. Make sure USB cable is unplugged. Wait until vibrator indicates it's turned off
6) Click Download button in SP Flash tool, confirm warning complaining about not all files being selected
7) Connect your phone and wait for the flash process to finish (indicated by window with green circle)
8) Unplug USB cable. Hold down Volume+ while turning your phone on to boot into recovery
Click to expand...
Click to collapse
Backing up your IMEI
Different Methods are available for this.
1) Use any RootExplorer to copy file /data/nvram/md/NVRAM/NVD_IMEI/MPOB_001 to your external SD card. (or if that folder does not exists, try /nvram/md/NVRAM/NVD_IMEI/MPOB_001). It is good to backup the entire folder /data/nvram/md/NVRAM.
2) Back up using Mobile Uncle utility. Click on Mobileuncle Tools --> Click IMEI Backup Restore (MTK) --> Backup/Restore
Restore your IMEI
Code:
1- Open Mobile Uncle Tools.
2- Goto Engineer Mode
3- Select Engineer mode[MTK]
4- Under Connectivity Tab go to CDS information
5- Select Radio Information
6- Select Phone1 (for the first imei)
7- at the top there is a command line which begins “AT+” just type there “AT +EGMR=1,7,”IMEI_1? (instead of IMEI_1 put your first imei number)
8- hit send command
9- You will / may get a confirmation that "sent to mSend".
10-Now come back and select “Phone2?
11-at the top there is a command line which begins “AT+” just type there “AT +EGMR=1,10,”IMEI_2? (instead of IMEI_2 put your second imei number)
12-Then just reboot the phone.
13- Dial ” *#06#” to Check Imei.
Factory ROM Backup for MT65xx via MTK Droid Root & Tools For BackUp & Unbrick
It's tested and working...
How to install ADB USB driver in window 7
use this method also in window xp,if any driver not install
Google USB Driver Rev 7 ( ADB driver )
inside three dll file driver
1-WdfCoInstaller01009.dll
2-winusbcoinstaller2.dll
3-WUDFUpdate_01009.dll
link
Click Here
Before use it is necessary to check that:
adb drivers are installed. Check device manager--> unknown devices. ADB Drivers attached.
Now the Tool
Credits: umesh gaba
[MOD][4.1 4.2] Extend Phone Storage 1.5, 2.5GB A116 (Other MT6589 Devices on request)
[Solution] NVRAM WARNING: Err = 0x10
Download this zip Click Here
Prerequisites:
You have to backup IMEI of your phone (both sim slot).
Step 1 - Extract the WiFi Fix files and place them in a folder on your memory card
Step 2 - Open Root Explorer
Step 3 - Click on Mount R/W
Step 4 - Click on data
Step 5 - Scroll down to the folder named nvram
Step 6 - Open APCFG folder
Step 7 - Open APRDEB folder
Step 8 - Delete the WIFI and WIFI_CUSTOM files
Step 9 - Now copy/move the files on your sdcard to data/nvram/APCFG/APRDEB and Paste
Step 10 - After pasting both the files, close Root Explorer and REBOOT your phone.
Here is another method Click Here
The bad news is.

Vijay have u bot the mobile..
Sent from my AUXUS Nuclea N1 using xda app-developers app

can you provide a review of the phone?
akashavel said:
Vijay have u bot the mobile..
Sent from my AUXUS Nuclea N1 using xda app-developers app
Click to expand...
Click to collapse
Hello dude,
i have booked this phone, and i am seriously waiting for some reviews.
It would be great if there was a video review done by you on you tube or where ever you are comfy.
The specs are awesome but there are some negative opinions as well.
This would help.
Thanks

akashavel said:
Vijay have u bot the mobile..
Sent from my AUXUS Nuclea N1 using xda app-developers app
Click to expand...
Click to collapse
Yes, I am in batch II.

dhavalg said:
Hello dude,
i have booked this phone, and i am seriously waiting for some reviews.
It would be great if there was a video review done by you on you tube or where ever you are comfy.
The specs are awesome but there are some negative opinions as well.
This would help.
Thanks
Click to expand...
Click to collapse
videos posted by me..
https://www.youtube.com/user/akashavel/videos
also chk this fb page
https://www.facebook.com/groups/Ibe...39765010250/?ref=notif&notif_t=group_activity

Hi Guys,
Even I have bought this phone and awaiting delivery, I was promised by 4th Aug. Lets see. The specs of this phone seems to be great other than the 4GB storage. I hope that apps2sd works really fine and I am able to store all my game data on the SD card. Wanted to know more info of this phone and the rom.
Regards,
Kailash

can't decide what to buy
is the costumer service good...i am really thinking to buy this phone but this brand was never heard before by me.....
in ur opinion which phone would be better
1. canvas 4 (micromax)
2. auxus nuclea n1 (iberry)
3. Xolo play (XOLO)

Thanks...
akashavel said:
videos posted by me..
https://www.youtube.com/user/akashavel/videos
also chk this fb page
https://www.facebook.com/groups/Ibe...39765010250/?ref=notif&notif_t=group_activity
Click to expand...
Click to collapse
That was really helpful, but i hoped some words about the phone from your mouth as well.
Need some comparison too,
But any ways it was awesome....I am going to continue with my order, actually i was planning on cancelling it. But now not...
Thanks for the videos.
Hope we get roms for it as well.

:victory: Yesss... XDA Thread for Auxus Nuclea.. feeling exciting.. Best Wishes, Guy.. :good::good:

dhavalg said:
That was really helpful, but i hoped some words about the phone from your mouth as well.
Need some comparison too,
But any ways it was awesome....I am going to continue with my order, actually i was planning on cancelling it. But now not...
Thanks for the videos.
Hope we get roms for it as well.
Click to expand...
Click to collapse
only thing is RAM so many apps consumes more memory .waiting for tweaked ROM.other than that the phone is gud..

I prefer to use Titanium Backup to freeze unwanted app rather to uninstall.. this app will save lots of RAM..

without source kernals cant we install custom Roms or stock roms, iam newbie to these things, i have a doubt, i have seen so many custom ROMs for samsung devices that means have samsung provided the source kernals???? please reply any experts

Without kernel source who would buy this phone and on top of that its Chinese brand better buy micromax Indian brand.....

ashok20205 said:
without source kernals cant we install custom Roms or stock roms, iam newbie to these things, i have a doubt, i have seen so many custom ROMs for samsung devices that means have samsung provided the source kernals???? please reply any experts
Click to expand...
Click to collapse
Yes, We can install Custom ROMs (Themed ROMs or Ported ROMs). But, with kernel sources a lot of development can happen. :good:

akashavel said:
only thing is RAM so many apps consumes more memory .waiting for tweaked ROM.other than that the phone is gud..
Click to expand...
Click to collapse
No need to wait for a Custom ROM. You can try One-Power-guard app, Clean master and Greenify app's.

Chris s5830i said:
Without kernel source who would buy this phone and on top of that its Chinese brand better buy micromax Indian brand.....
Click to expand...
Click to collapse
This mobile is good at it price with the spec's. Even Micromax is not providing kernel sources. Also, compared to the support of Micromax, iBerry is doing best.

abhiek bist said:
is the costumer service good...i am really thinking to buy this phone but this brand was never heard before by me.....
in ur opinion which phone would be better
1. canvas 4 (micromax)
2. auxus nuclea n1 (iberry)
3. Xolo play (XOLO)
Click to expand...
Click to collapse
Check the facebook page. Then you can decide

Can you post link for CWM for nuclea N1
can you help me with the link for CWM

Micromax Canvas doodle 3 [A102] Official Development thread.

Micromax canvas doodle 3 a.k.a A102 was released recently, a budget android phone or phablet. With a Meditek MT6572 processor and Android 4.2.2 stock.
Development thread for a local market phone exists rarely, and that rare thread is created by me[emoji15] .
Prime

Rooting Micromax Canvas Doodle 3 A102 with 1GB RAM Kitkat 4.4.2
Download recovery.img
You Need SP_Flash_Tool_v5.1352.01.zip
and UPDATE-SuperSU-v2.02.zip
Download below
put UPDATE-SuperSU-v2.02.zip in your SD Card
Now extract Sp Flash Tools and download Scatter File from Below
1. Open Sp Flash Tools
2. Put Scatter file and recovery.img in same folder
3. Load Scatter File Downloaded from below
4. now the recovery will be automatically selected
5. Install Drivers from here micromaxinfo.com/download.ashx?section=mobile-A102&file=Canvas_Doodle_3_Driver.zip
6. Switch off your Phone Pull out Battery and Connect it to PC using USB Cable
7. Click on Download
8. After the process is completed a green tick will appear
9. Now disconnect mobile and Put battery in and goto recovery mode using volume up+Power button select recovery and then push vol Down button
here is your custom recovery now select install zip from sdcard using power up and down buttons and select from power button
Now a prompt will appear select yes.
Now go back using soft keys on your mobile and reboot ..
Here you are
Your Phone is Rooted Now..

Kindly find the images of SP Flash & the flashed recovery.
It's for reference and guide.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

thanxxxxxxxx
was very helpfull ,,,,doodle 3 kitkat version root.......................try it,,,, its work for kitkat ota

Rooting Micromax canvas Doodle 3 .....
Friends if anyone is getting difficulty in going to recovery mode using Power+Volume up button
Download adb setup zip file from below and install the adb setup
then
goto Command Prompt and type
adb reboot recovery
your phone will goto recovery mode automatically
then rest is given in above post.
dont forget to ht thanks if helped.

Finaly root
navi95295 said:
Download recovery.img
You Need SP_Flash_Tool_v5.1352.01.zip
and UPDATE-SuperSU-v2.02.zip
Download below
put UPDATE-SuperSU-v2.02.zip in your SD Card
Now extract Sp Flash Tools and download Scatter File from Below
1. Open Sp Flash Tools
2. Put Scatter file and recovery.img in same folder
3. Load Scatter File Downloaded from below
4. now the recovery will be automatically selected
5. Install Drivers from here micromaxinfo.com/download.ashx?section=mobile-A102&file=Canvas_Doodle_3_Driver.zip
6. Switch off your Phone Pull out Battery and Connect it to PC using USB Cable
7. Click on Download
8. After the process is completed a green tick will appear
9. Now disconnect mobile and Put battery in and goto recovery mode using volume up+Power button select recovery and then push vol Down button
here is your custom recovery now select install zip from sdcard using power up and down buttons and select from power button
Now a prompt will appear select yes.
Now go back using soft keys on your mobile and reboot ..
Here you are
Your Phone is Rooted Now..
Click to expand...
Click to collapse
thanks bro,
finaly root my doodle 3 updated kitkat 1gb ram
i use below attached scatter file

MIUI ROM for Micromx Canvas A102
Here it Comes
MIUI ROM for Micromax Canvas Doodle 3 with 1GB ram
IS NO MORE WORKING

navi95295 said:
Download recovery.img
You Need SP_Flash_Tool_v5.1352.01.zip
and UPDATE-SuperSU-v2.02.zip
Download below
put UPDATE-SuperSU-v2.02.zip in your SD Card
Now extract Sp Flash Tools and download Scatter File from Below
1. Open Sp Flash Tools
2. Put Scatter file and recovery.img in same folder
3. Load Scatter File Downloaded from below
4. now the recovery will be automatically selected
5. Install Drivers from here micromaxinfo.com/download.ashx?section=mobile-A102&file=Canvas_Doodle_3_Driver.zip
6. Switch off your Phone Pull out Battery and Connect it to PC using USB Cable
7. Click on Download
8. After the process is completed a green tick will appear
9. Now disconnect mobile and Put battery in and goto recovery mode using volume up+Power button select recovery and then push vol Down button
here is your custom recovery now select install zip from sdcard using power up and down buttons and select from power button
Now a prompt will appear select yes.
Now go back using soft keys on your mobile and reboot ..
Here you are
Your Phone is Rooted Now..
Click to expand...
Click to collapse
this method is not working the flash app is not detecting my device .....its getting very annoying...cus I have been trying hard to root this phone with this version of OS...pls help me by making a video tutorial for rooting this phone

navi95295 said:
Download recovery.img
You Need SP_Flash_Tool_v5.1352.01.zip
and UPDATE-SuperSU-v2.02.zip
Download below
put UPDATE-SuperSU-v2.02.zip in your SD Card
Now extract Sp Flash Tools and download Scatter File from Below
1. Open Sp Flash Tools
2. Put Scatter file and recovery.img in same folder
3. Load Scatter File Downloaded from below
4. now the recovery will be automatically selected
5. Install Drivers from here micromaxinfo.com/download.ashx?section=mobile-A102&file=Canvas_Doodle_3_Driver.zip
6. Switch off your Phone Pull out Battery and Connect it to PC using USB Cable
7. Click on Download
8. After the process is completed a green tick will appear
9. Now disconnect mobile and Put battery in and goto recovery mode using volume up+Power button select recovery and then push vol Down button
here is your custom recovery now select install zip from sdcard using power up and down buttons and select from power button
Now a prompt will appear select yes.
Now go back using soft keys on your mobile and reboot ..
Here you are
Your Phone is Rooted Now..
Click to expand...
Click to collapse
your above steps are not working in my phone a102 ,doodle 3...i had recently upgarded to kitkat 4.4.2 .......none of the methods or rootapps are working for rooting this device
pls sir can you make one video tutorial for rooting this device with the above version of OS...asap

Rooting Micromax canvas Doodle 3 .....
damianlepcha said:
this method is not working the flash app is not detecting my device .....its getting very annoying...cus I have been trying hard to root this phone with this version of OS...pls help me by making a video tutorial for rooting this phone
Click to expand...
Click to collapse
Use following Link to Download the latest version of SP flash Tools and retry with the scatter file and recovery image given.
This will let you download recovery to your handset and getting Root.
copy and paste this link to your browser and download .. d-h.st/weue

couldn't reboot into recovery mode from doodle 3
My ram is 1 GB and my phone is rooted but I couldn't reboot into recovery plz anyone help meme
My PC is damaged plzzz anyone post a process to install CWM without PC
Thanks in Advance

Tapan Arya said:
My ram is 1 GB and my phone is rooted but I couldn't reboot into recovery plz anyone help meme
My PC is damaged plzzz anyone post a process to install CWM without PC
Thanks in Advance
Click to expand...
Click to collapse
Use Mobileuncle tools or Rebooter app for reboot into recovery mode.

I already used but doesn't works

Tapan Arya said:
I already used but doesn't works
Click to expand...
Click to collapse
If you are rooted then have u installed the CWM provided in Post #2
install using Mobileuncle tools
then root
Dont Forget to Endale USB Debugging mode from developer options
and reboot to recovery from mobile uncle tools.
It should reboot into recovery. if not then tell me what any error is coming ??

Error is that when I reboots into recovery micromax logo comes for 10 seconds and after that it restarts

Tapan Arya said:
Error is that when I reboots into recovery micromax logo comes for 10 seconds and after that it restarts
Click to expand...
Click to collapse
Just try to reinstall the recovery using mobileuncle tools and then reboot.
Hope it will work

I just tried to and updated recovery from mobile uncle but it shows as before

Please Help apk
Please someone attach me the stock camera app (and gallery), I've accidentally deleted it. My phone is doodle 3 A102 and is running 4.4.2 kitkat.

osamaanjum said:
Please someone attach me the stock camera app (and gallery), I've accidentally deleted it. My phone is doodle 3 A102 and is running 4.4.2 kitkat.
Click to expand...
Click to collapse
just copy and paste them in /system/app and change permissions to rw- r-- r-- and reboot
and for camera just restore factory settings if it didnt helped then reflash the stock Rom (System Only) and done.
Dont forget to backup your IMEI before doing anything.

osamaanjum said:
Please someone attach me the stock camera app (and gallery), I've accidentally deleted it. My phone is doodle 3 A102 and is running 4.4.2 kitkat.
Click to expand...
Click to collapse
Use ESfile Explorer to Copy it to system folder and change permissions..

[RECOVERY] TWRP 3.2.1 For C701F/DS [STABLE]

Team Win Recovery Project
It's Compatibe with Snapdragon Variants Of C7 Pro Such as C701F and C701F/DD.
If it's not working with your device or you have different model let me know. I would Build a Different Version of Recovery for your Model.
#include <std_disclaimer.h>
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Special Notes:
1. READ THE GUIDE.
2. KNOX will be tripped once you flashed custom binaries to your phone.
(Your warranty may be voided. However, this may not affect you if your country, European Union, for example, forces Samsung to provide hardware warranty regardless of software status.)
More Infos: https://en.m.wikipedia.org/wiki/Rooting_the_Android_operating_system
3. Samsung Firmware OTA (aka System Updates) will no longer work once you flashed custom binaries.
(You can flash custom ROMs if you want to keep the OS up-to-date.)
4. It is HIGHLY UNRECOMMENDED to purchase any access to any kind of private forums, ROMs or Kernels.
(DO NOT GET FOOLED.)
5. You HAVE to use newer version of Odin (>3.13) if you want to flash stock ROMs.
Download:
Galaxy C7 Pro (C701F/DS):
https://androidfilehost.com/?w=files&flid=275664
Sources:
https://github.com/TeamWin
https://github.com/aapav01/android_device_samsung_c7proltedd-twrp
Changelog:
Check #2.
Guide:
Check #3.
Show your appreciation:
Click Thanks!, Rate 5-star or/and Donate to me.
(You Can donate me Steam Gift Cards)
To contribute:
TWRP Code Review
Github pull requests will be ignored.

Change log:
Note that this page only includes device-specific changes. For global TWRP changes, go to twrp.me.
June 12, 2018 (twrp-3.2.1-0):
Fixed MTP
Fixed encryption on ASOP ROM (Samsung is unsupported)
Enable NTFS Support
Fixed Mount Issues of partition
Add Support OREO ROMs
Added EFS Backup
And MORE

Guides:
Notice: It may wipe all your data including those in internal storage.
Part 1 - HOW-TO FLASH TWRP:
1. In your ROM, go to Settings -> About device. Tap 7 times on Build number to enable Developer options.
2. Go to Settings -> Developer options and enable OEM Unlock option.
3. Download and Install Samsung Mobile Phones Drivers.
- Option 1: Download and Install Smart Switch for PC.
- Option 2: Download and Install standalone driver package.
4. Download and extract Odin (Samsung's Flash Tool) to your computer.
5. Download a .tar image of TWRP.
6. Reboot your device to download mode.
- Hold [VOLUME DOWN] + [HOME BUTTON] + [POWER] for approx. 15 seconds.
- Read the warning carefully.
- If you agree, press [VOLUME UP] to get into Download mode. If you don't agree, STOP.
7. Open Odin and place that TWRP tar file in the [AP] slot.
8. Connect your phone.
9. Hold [VOLUME UP] + [HOME BUTTON] + [POWER] on your phone and then press start on Odin.
10. Wait for the phone to reboot. DO NOT release [VOLUME UP] + [HOME BUTTON] + [POWER] or you may not reboot into TWRP.
Part 2 - HOW-TO INITIALIZE TWRP: (for new phones)
1. If you completed Part 1 successfully, you should be in TWRP now. At this point, you will reach the screen asking you if you want to allow system modifications.
2. Select "Keep /system RO". (Don't swipe right or you may not be able to boot into system if you failed to complete next steps. However, you can swipe right to allow modifications if you are confident that you can complete next steps.)
3. Go to "Wipe" menu of TWRP and you will find "Format Data". Press "Format Data" and type "yes" to continue.
4. Go to "Reboot" menu and Press "Recovery" to reboot TWRP.
5. Download the latest dm-verity and force encryption disabler zip on your computer.
6. Transfer the zip to your phone.
- Option 1: MTP: Connect your phone with computer and just copy the zip to internal storage. (similar to how you transfer files when in system.)
- Option 2: ADB: Connect your phone with computer and run command "adb push /path/to/zip /sdcard/".
- Option 3: External SD: Copy the zip to an external SD and then insert the card to your phone.
7. Go to "Install" menu of TWRP and flash the zip.
TWRP is initialized and fully functional at this stage. Now you can either reboot into system or root, flash custom ROMs via TWRP.
Part 3 - HOW-TO ROOT:
1. Download the flashable zip.
- Option 1: Magisk
- Option 2: SuperSU
2. Transfer the zip to your phone.
3. Go to "Install" menu of TWRP and flash the zip.
Part 3a - HOW-TO FLASH CUSTOM ROMS:
1. Download the flashable zip.
2. Transfer the zip to your phone.
3. Go to "Install" menu of TWRP and flash the zip.
Simple.

dear.......followed procedure....but... ( error is set warranty bit kernel..)...now any soln...pl reply..
thanxs with deep warm regards

I have the SM-C7018 version of this phone and, by following your guide, I was able to set up TWRP on Android 7.0 and flash GAPPS.
Thank you very much for this!
EDIT: Maybe it was just in my case, but for those of you that wish to install GAPPS on this device, keep in mind that you must not reset it to the factory conditions after installing GAPPS, as the Play services will FC once the phone boots up, and you will not be able to use it anymore. I had to re-flash the firmware. Also, I've used the Pico package, ARM x64, Android 7.0.
EDIT 2: Unfortunately, I couldn't manage to get the GApps working. The Google Framework Services would always crash when opening any google application for the first time or when trying to add the account from the Settings Menu. Anyone had any success with adding GApps on the Nougat firmware?

SPG30759 said:
dear.......followed procedure....but... ( error is set warranty bit kernel..)...now any soln...pl reply..
thanxs with deep warm regards
Click to expand...
Click to collapse
it's normal on samsung devices

aapav01 said:
it's normal on samsung devices
Click to expand...
Click to collapse
Hi, I did the steps you mentioned, but after completion I checked with Root Checker app it says "Root not installed properly". Do you know why?

My device is C7010. Can it use your TWRP as well?

c7 PRO c7018
Will this tprw work with c7018 model? and with c7018 + oreo?
aapav01 said:
Team Win Recovery Project
It's Compatibe with Snapdragon Variants Of C7 Pro Such as C701F and C701F/DD.
If it's not working with your device or you have different model let me know. I would Build a Different Version of Recovery for your Model.
#include <std_disclaimer.h>
Special Notes:
1. READ THE GUIDE.
2. KNOX will be tripped once you flashed custom binaries to your phone.
(Your warranty may be voided. However, this may not affect you if your country, European Union, for example, forces Samsung to provide hardware warranty regardless of software status.)
More Infos: https://en.m.wikipedia.org/wiki/Rooting_the_Android_operating_system
3. Samsung Firmware OTA (aka System Updates) will no longer work once you flashed custom binaries.
(You can flash custom ROMs if you want to keep the OS up-to-date.)
4. It is HIGHLY UNRECOMMENDED to purchase any access to any kind of private forums, ROMs or Kernels.
(DO NOT GET FOOLED.)
5. You HAVE to use newer version of Odin (>3.13) if you want to flash stock ROMs.
Download:
Galaxy C7 Pro (C701F/DS):
https://androidfilehost.com/?w=files&flid=275664
Sources:
https://github.com/TeamWin
https://github.com/aapav01/android_device_samsung_c7proltedd-twrp
Changelog:
Check #2.
Guide:
Check #3.
Show your appreciation:
Click Thanks!, Rate 5-star or/and Donate to me.
(You Can donate me Steam Gift Cards)
To contribute:
TWRP Code Review
Github pull requests will be ignored.
Click to expand...
Click to collapse

Can I use this to port TWRP for 10.or G
Specs of 10.or G
Snap 626
4gb ram
Also pls reply what hardware needs to be same for porting.
And does kernel matter in Porting these images???
Thanx in advance

@aapav01 plz make twrp for C7000 oreo
tnks

a7 2015
Can build for me this same rom its humble request

Thank you!

c7 pro twrp for oreo
hi
i have series gapps problem .
can you plz make one for c7 pro sm-c7018 oreo .
twrp has no version for it .
baseband version: c7018zmu2cri1
buildnumber: r16nw.c7018zmu2cri1.
2018/09/14
ty

phone stucked at samsung logo and set bit : kernal
I followed same step and my phone isnt booting now
stucked at samsung logo and yellow top right says set bit: kernal
please help

try this
ashokrathi said:
I followed same step and my phone isnt booting now
stucked at samsung logo and yellow top right says set bit: kernal
please help
Click to expand...
Click to collapse
try pressing vol down and power at same time time then phone goes to power off then switch from vol down to vol up holding the power button now as soon as screen display starts leave both buttons it will now boot into twrp recovery go to wipe format data and type yes then flash no dm verity and magisk as per instruction given

My device is C7010. Can it use your TWRP as well?

aapav01 said:
Guides:
Notice: It may wipe all your data including those in internal storage.
Part 1 - HOW-TO FLASH TWRP:
1. In your ROM, go to Settings -> About device. Tap 7 times on Build number to enable Developer options.
2. Go to Settings -> Developer options and enable OEM Unlock option.
3. Download and Install Samsung Mobile Phones Drivers.
- Option 1: Download and Install Smart Switch for PC.
- Option 2: Download and Install standalone driver package.
4. Download and extract Odin (Samsung's Flash Tool) to your computer.
5. Download a .tar image of TWRP.
6. Reboot your device to download mode.
- Hold [VOLUME DOWN] + [HOME BUTTON] + [POWER] for approx. 15 seconds.
- Read the warning carefully.
- If you agree, press [VOLUME UP] to get into Download mode. If you don't agree, STOP.
7. Open Odin and place that TWRP tar file in the [AP] slot.
8. Connect your phone.
9. Hold [VOLUME UP] + [HOME BUTTON] + [POWER] on your phone and then press start on Odin.
10. Wait for the phone to reboot. DO NOT release [VOLUME UP] + [HOME BUTTON] + [POWER] or you may not reboot into TWRP.
Part 2 - HOW-TO INITIALIZE TWRP: (for new phones)
1. If you completed Part 1 successfully, you should be in TWRP now. At this point, you will reach the screen asking you if you want to allow system modifications.
2. Select "Keep /system RO". (Don't swipe right or you may not be able to boot into system if you failed to complete next steps. However, you can swipe right to allow modifications if you are confident that you can complete next steps.)
3. Go to "Wipe" menu of TWRP and you will find "Format Data". Press "Format Data" and type "yes" to continue.
4. Go to "Reboot" menu and Press "Recovery" to reboot TWRP.
5. Download the latest dm-verity and force encryption disabler zip on your computer.
6. Transfer the zip to your phone.
- Option 1: MTP: Connect your phone with computer and just copy the zip to internal storage. (similar to how you transfer files when in system.)
- Option 2: ADB: Connect your phone with computer and run command "adb push /path/to/zip /sdcard/".
- Option 3: External SD: Copy the zip to an external SD and then insert the card to your phone.
7. Go to "Install" menu of TWRP and flash the zip.
TWRP is initialized and fully functional at this stage. Now you can either reboot into system or root, flash custom ROMs via TWRP.
Part 3 - HOW-TO ROOT:
1. Download the flashable zip.
- Option 1: Magisk
- Option 2: SuperSU
2. Transfer the zip to your phone.
3. Go to "Install" menu of TWRP and flash the zip.
Part 3a - HOW-TO FLASH CUSTOM ROMS:
1. Download the flashable zip.
2. Transfer the zip to your phone.
3. Go to "Install" menu of TWRP and flash the zip.
Simple.
Click to expand...
Click to collapse
I want to try this but my phone (c701f-ds) never boots into download mode or recovery mode consistently. I bricked the phone trying to root it throught the magisk app, using this very version of twrp. I got it back. I was able to flash the original stock oreo rom using odin
But to get the phone back I didn't go through the (blue screen) Download Mode, Instaed I got into the recovery envoronment (very hit and miss) then chose to reboot into bootloader mode, where I saw it yellow at the top of the screen "download mode" but not the blue screen of the usual download mode.
In this bootloader/download mode environment I connected the phone to the laptop. Odin recognised the phone and I loaded the stock rom into AP, and the appropriate files into the other boxes (I used Home_CSC instead of CSS, essentila for getting VOLTE to work). It flashed successfully. (a status bar appeared on the phone which corresponded to the download process)
But that wasn't the method that anyone else recommended.
I would try flashing the twrp tar file in the same way but there is no guarentee I could get into the twrp environment since holding [VOLUME UP] + [HOME BUTTON] + [POWER] doesn't always, or even often, get me into recovery mode.
I can use adb to reboot into recovery and from there get into bootloader/download mode but not again if the os doesnt load
Any advice?
And you say that eventhough the phone is already in download mode, that after you connect the phone to the pc where odin is loaded and has initialized the tar file, you have to press and hold [VOLUME UP] + [HOME BUTTON] + [POWER] and then press start on Odin. Then continue to hold these 3 buttons till the phone reboots into twrp. Why not just press start on odin without holding these 3 buttons? If the phone just shuts off after flashing twrp, would turning it on by holding those 3 buttons bring the phone (except mine perhaps) into twrp recovery?
What happens if the phone doesn't boot into recovery/twrp? Is it bricked? And if it does boot into the os, could you use adb to get into twrp?
I am being cautious due to the difficulty in getting the phone back after bricking it last time and because there is no guarentee that an ke combos will definitely get my phone into recovery or download mode.
Help is appreciated.