Cherry mobile Omega HD (i-mobile IQ6)

Cherry mobile Omega HD (i-mobile IQ6) - Android General

Omega HD root
Disclaimer: I will not be liable for bricked devices. Follow these instructions at your own risk. ROOTING VOIDS WARRANTY, as per Cherry Mobile. Please be guided accordingly.
This tutorial is not recommended for newbies. Knowledge of basic adb and fastboot commands is helpful. Better if you have previously installed ADB drivers.
Downloads (http://www.mediafire.com/?ar2ccya8395d1):
SuperSU zip
TWRP
SP Flash Tool
MTK Drivers
MTK 6577 scatter file
if the driver didn't work download this http://www.4shared.com/zip/YXlLFoLm/6577driver_install_3_steps.html
install folder step 1 to 3
Place the scatter file and TWRP recovery in the SAME FOLDER.
rename twrp recovery to recovery.img
1. While the phone is still on, enable USB debugging (Settings > Developer options) then plug into PC. Allow drivers to install. Install the MTK drivers as well.
2. Mount phone as USB storage. Copy SuperSU zip to internal or external SD card. Unmount USB storage, then unplug phone from PC.
2. Turn off phone. Remove the battery.
3. Start SP Flash Tool. Under "Scatter-loading," choose the MT6577_Android_scatter_emmc.txt. You will see that RECOVERY has a check beside it. Click on "Download." A warning will appear, proceed anyway.
4. With your phone still off and the battery out, plug it in to the PC. Flashing should start. It will only take a few seconds. You'll see a green circle when it's done.
5. Unplug USB cable and put the battery back.
6. Enter recovery mode by Power and Volume + button. Release both buttons when you see the boot menu. Use Volume + to highlight "recovery." Then use Volume - to confirm.
7. Click "Install." Choose the appropriate tab (internal or external SD card).
8. Select UPDATE-SuperSU-1.25 zip. Swipe to confirm the update. It will flash. Go back to main menu of TWRP.
9. Click "Reboot system." Wait until you are fully booted into your homesceen.
10. Once booted, you should see SuperSU in your app drawer.
credits to ish gridote
OmegaXtremeHD
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
s3 bootanimation n sound
s3 boot logo
Jelly bean icons
iphone ringtones
google play music
dolphin browser
apex launcher
deodexed
busybox
rooted
init.d
signal tweaks
3g tweaks
battery tweaks
gpu rendering
dns tweaks
media tweaks
v6 supercharger
kickasskernel
crossbreeder
reorganized build.prop file
uploading
http://www.4shared.com/folder/dJXI2ODd/_online.html
try open first in case of corrupt file
remove crossbreeder for much better battery
flash uninstall zip http://forum.xda-developers.com/showthread.php?t=2113150
and underclock for much longer battery download setcpu or no frillcpu or anything u want i dnt care..
save rom in SD card
reboot to CWM/TWRP
install rom via SD card
reboot
I'm not responsible for any loss of data or brick....
i think this only works on iq6A

do you already own this phone?

Cherry mobile Omega HD info states that its a dual core phone while all info about i-mobile IQ6 states its a single core phone. does anyone know which mediatek chipset the Omega HD uses? It's GPU?

yes i had it

How?
How can we flash the CWM to the Omega HD if you don't even give us a flashtool? Is this Rooting process tested? is it working?

Please help me
Wil53664 said:
yes i had it
Click to expand...
Click to collapse
Sir, can I have a copy of the Setting.apk of your Cherry Mobile HD? i've accidentally forgot to have a backup of it and now, i've accidentally just erased it. please help me. thankyou very much

Pretty Please?
Wil53664 said:
yes i had it
Click to expand...
Click to collapse
please post the Settings.apk of the Cherry Mobile Omega HD sir. I really need it it would be appreciated if you post it here.

How to Backup the phone
just bought the phone yesterday
do yo guys know how to back up this jellybean phone?

Hey guys, if you have FB we have a group with most of oHD users. Just search "CherryMobileOmegaHD" in FB (can't post links yet. sorry)
There are custom roms in the group, the usual rom cooked from dsdixda's kitchen (zipalign, deodexed, rm bloatwares)
@cyzarine
What do you mean with backup? We have the stock rom in the group, you might want to check it out.

Bummer! I'm stuck at step 3!
You will see that RECOVERY has a check beside it. Click on "Download." A warning will appear, proceed anyway.
Click to expand...
Click to collapse
-- umm... NO, I DON'T!! There must be a step that's missing... :-S
edit:
nevermind. I forgot to rename TWRP file to "recovery"
Thanks for this!

anyone have a kernel that have oc"?

In need...
Woke up to a drained Omega HD today.
Plugged it in to have it charged.
Switched it on afterwards.
"OmegaHD" flashed before my eyes, followed by a blank screen with the familiar Cherry Mobile tune playing on the background. And then nothing! NO DISPLAY! I touch the screen and there are sounds playing to confirm each press, which means I am pressing on the right places -- only that there is NO DISPLAY APPEARING.
I switch it on and off, still the same results.
Wiped cache. Nothing... Since it's practically new, I go ahead and factory-restore the thing... still the same results. NO DISPLAY! :-S
What else can I do to this device to have it work properly?!

Have you installed any custom rom or any other zip files with your phone?

xMinistro said:
Have you installed any custom rom or any other zip files with your phone?
Click to expand...
Click to collapse
do have stock rom can you give plsss......

---------- Post added at 11:02 PM ---------- Previous post was at 10:41 PM ----------
[/COLOR]
Wil53664 said:
Omega HD root
Disclaimer: I will not be liable for bricked devices. Follow these instructions at your own risk. ROOTING VOIDS WARRANTY, as per Cherry Mobile. Please be guided accordingly.
This tutorial is not recommended for newbies. Knowledge of basic adb and fastboot commands is helpful. Better if you have previously installed ADB drivers.
Downloads (http://www.mediafire.com/?ar2ccya8395d1):
SuperSU zip
TWRP ported by me
SP Flash Tool
MTK Drivers
MTK 6577 scatter file
if the driver didn't work download this http://www.4shared.com/zip/YXlLFoLm/6577driver_install_3_steps.html
install folder step 1 to 3
Place the scatter file and TWRP recovery in the SAME FOLDER.
rename twrp recovery to recovery.img
1. While the phone is still on, enable USB debugging (Settings > Developer options) then plug into PC. Allow drivers to install. Install the MTK drivers as well.
2. Mount phone as USB storage. Copy SuperSU zip to internal or external SD card. Unmount USB storage, then unplug phone from PC.
2. Turn off phone. Remove the battery.
3. Start SP Flash Tool. Under "Scatter-loading," choose the MT6577_Android_scatter_emmc.txt. You will see that RECOVERY has a check beside it. Click on "Download." A warning will appear, proceed anyway.
4. With your phone still off and the battery out, plug it in to the PC. Flashing should start. It will only take a few seconds. You'll see a green circle when it's done.
5. Unplug USB cable and put the battery back.
6. Enter recovery mode by Power and Volume + button. Release both buttons when you see the boot menu. Use Volume + to highlight "recovery." Then use Volume - to confirm.
7. Click "Install." Choose the appropriate tab (internal or external SD card).
8. Select UPDATE-SuperSU-1.25 zip. Swipe to confirm the update. It will flash. Go back to main menu of TWRP.
9. Click "Reboot system." Wait until you are fully booted into your homesceen.
10. Once booted, you should see SuperSU in your app drawer.
credits to ish gridote
Click to expand...
Click to collapse
Hi. Can you please post a mirror on the twrp-omegahd.img file? All of the other files have been downloaded except for the img file. Error comes up.

bakes5981 said:
Bummer! I'm stuck at step 3!
-- umm... NO, I DON'T!! There must be a step that's missing... :-S
edit:
nevermind. I forgot to rename TWRP file to "recovery"
Thanks for this!
Click to expand...
Click to collapse
please hit thanks if this helps

OmegaXtremeHD link issues
OmegaXtremeHD link is not working .... 509 error .... any mirror or alternative links?

Wil53664 said:
Omega HD root
Disclaimer: I will not be liable for bricked devices. Follow these instructions at your own risk. ROOTING VOIDS WARRANTY, as per Cherry Mobile. Please be guided accordingly.
This tutorial is not recommended for newbies. Knowledge of basic adb and fastboot commands is helpful. Better if you have previously installed ADB drivers.
Downloads (http://www.mediafire.com/?ar2ccya8395d1):
SuperSU zip
TWRP ported by me
SP Flash Tool
MTK Drivers
MTK 6577 scatter file
if the driver didn't work download this http://www.4shared.com/zip/YXlLFoLm/6577driver_install_3_steps.html
install folder step 1 to 3
Place the scatter file and TWRP recovery in the SAME FOLDER.
rename twrp recovery to recovery.img
1. While the phone is still on, enable USB debugging (Settings > Developer options) then plug into PC. Allow drivers to install. Install the MTK drivers as well.
2. Mount phone as USB storage. Copy SuperSU zip to internal or external SD card. Unmount USB storage, then unplug phone from PC.
2. Turn off phone. Remove the battery.
3. Start SP Flash Tool. Under "Scatter-loading," choose the MT6577_Android_scatter_emmc.txt. You will see that RECOVERY has a check beside it. Click on "Download." A warning will appear, proceed anyway.
4. With your phone still off and the battery out, plug it in to the PC. Flashing should start. It will only take a few seconds. You'll see a green circle when it's done.
5. Unplug USB cable and put the battery back.
6. Enter recovery mode by Power and Volume + button. Release both buttons when you see the boot menu. Use Volume + to highlight "recovery." Then use Volume - to confirm.
7. Click "Install." Choose the appropriate tab (internal or external SD card).
8. Select UPDATE-SuperSU-1.25 zip. Swipe to confirm the update. It will flash. Go back to main menu of TWRP.
9. Click "Reboot system." Wait until you are fully booted into your homesceen.
10. Once booted, you should see SuperSU in your app drawer.
credits to ish gridote
OmegaXtremeHD
s3 bootanimation n sound
s3 boot logo
Jelly bean icons
iphone ringtones
google play music
dolphin browser
apex launcher
deodexed
busybox
init.d
signal tweaks
3g tweaks
battery tweaks
v6 supercharger
kickasskernel
crossbreeder
download link
https://www.dropbox.com/s/8q1c6db45uegepk/OmegaXtreme.zip
updated link
save rom in SD card
reboot to CWM/TWRP
WIPE DATA/FACTORY RESET
install rom via SD card
reboot
Click to expand...
Click to collapse
Hey buddy,
Where's the file..??

StanleyD said:
Hey buddy,
Where's the file..??
Click to expand...
Click to collapse
will update link later

having trouble with some apps working on my Omega HD. a couple of my Android mainstays are Haxsync and Swiftkey. on my Omega HD, they run no problem, but if the unit powers off for whatever reason, when I turn it back on, my Haxsync account (under Settings/Accounts) disappears, requiring me to set up the app again, and Swiftkey is no longer activated as my default input. any help?

Related

[DISCUSSION][GUIDE][PORT][ROM] Alcatel One Touch 4030 S'Pop/Glory 2 Development

This thread is for discussion for the development of this device. All interested devs are very welcome to join and help.
I started working on this device since I got it day 1 on March 11, 2013. Slowly, I progressed to every step in learning more about this device. Since then, many have joined finding ways to make this device better.
UPDATE:
This thread is old and very few to none uses this device anymore. I will leave this thread here for your reference.
All of the developments of this device will still be posted here so always keep in touch with this thread for great news.
Cheers! :good:

Unbrick theory...
trying the one touch upgrade utility. it wipes all data in phone and installs a fresh and latest ROM for the device. i guess this will also fix a bricked device somehow.
after this i will try to root it again using MTK tools and ap flash tools with a different idea in my mind... hope it works this time...
[EDIT] UNBRICK METHOD CONFIRMED WORKING!!!

One touch Upgrade
Hello there I'm a total noob in rooting and unlocking bootloads. I just got the same phone as my first android phone and wondered how to root it and I end up here. Now I'm asking how did you get the one touch upgrade software. I've searched the whole alcatel website but I keep getting on the FAQ page. Would you be so kind to put up the link for the software because I kinda bricked my phone here. I was also wondering what speed did you use during your Bin4ry script root attempt? Normal or Special? Keep doing a good job. Thanks for having the time to look for ways to root this phone.

sabinbp said:
Hello there I'm a total noob in rooting and unlocking bootloads. I just got the same phone as my first android phone and wondered how to root it and I end up here. Now I'm asking how did you get the one touch upgrade software. I've searched the whole alcatel website but I keep getting on the FAQ page. Would you be so kind to put up the link for the software because I kinda bricked my phone here. I was also wondering what speed did you use during your Bin4ry script root attempt? Normal or Special? Keep doing a good job. Thanks for having the time to look for ways to root this phone.
Click to expand...
Click to collapse
I tried the normal mode as Bin4ry said that the others might brick the phone it it wasn't the right model. did you brick it using the srcipt? any way. still trying to root it and finding help from rua1 that has a great knowledge in MTK phones...
here's the link of the upgrade utiliuty... just install it and choose alcatel 4030 (if your phone is s'pop) then power of the phone remove the battery and follow the instructions on PC and wait till it says plug the phone while powered off.. plug the usb (without battery) then wait for it to detect the device. when it loads, put the battery back and wait for it to download the firmware.. it will take hours to download it.. it's about 2+gigs... good luck on unbricking.. hope it works...

Phone unbricked
Many thanks for the software. My phone is now back to stock rom. for the Bin4ry I also tried Normal because I thought it was for tabs only. So MTK is the only course of action? Any news on fixing the 2 point horizontal bug? and the alcatel FAQ says there's this TCL calibration that you can activate to you know "calibrate" the touch screen. Do you also get the problem where in the stock alarm app alarms but you can't dismiss it ( I set it to crazy mode ) where you need to press 3 buttons to dismiss but still won't stop I really need to pull the battery out. Help please Thanks in advance.

sabinbp said:
Many thanks for the software. My phone is now back to stock rom. for the Bin4ry I also tried Normal because I thought it was for tabs only. So MTK is the only course of action? Any news on fixing the 2 point horizontal bug? and the alcatel FAQ says there's this TCL calibration that you can activate to you know "calibrate" the touch screen. Do you also get the problem where in the stock alarm app alarms but you can't dismiss it ( I set it to crazy mode ) where you need to press 3 buttons to dismiss but still won't stop I really need to pull the battery out. Help please Thanks in advance.
Click to expand...
Click to collapse
Great. So my theory really worked. Glad you unbricked it. I'm getting closer to rooting it. Just having problems flashing the cwm. Ones I managed to flash it, rooting may be successful. I use Mtk tools and flash tools and get help from rua1. Didn't use my alarm before so i'm not sure about the bug. Maybe you don't have to set it in crazy mode..

I tried to set the alarm in crazy mode and everything works fine. Just dismiss, unlock, and tap the three buttons with numbers and your done..

Rooted, finally!!
I finally rooted the alcatel spop. I will make a guide maybe later how I did it...

[GUIDE]How to flash CWM recovery and root Alcatel One Touch S'POP 4030
How to flash CWM recovery and root Alcatel One Touch S'POP 4030X(Glory 2)
Disclaimer: Your warranty is now void. You do this in your own risk. I do not take any responsibility to your device. This will definitely brick your device which is normal but follow the right instructions to make it work again.
Credits: This is tuts would not be possible without the help from the creator of MTKdroid tools, rua1 from XDA Developers. Thank the guy for his wonderful tool. If you wanna know how I did it, go to his thread right here. I also wanna acknowledge The Solutor and rimmon1971's efforts for porting the TWRP to our device. You can find The Solutor's work here.
Requirements:
1. A windows based PC
2. MTK Droid Root & Tools & SP Flash Tool
3. Universal ADB driver
4. One Touch Upgrade S
5. Root script
6. Patience
7. Most important! Use your brain!
Important!
To make this work without errors, don't use other drivers available in the web. Just install One Touch Upgrade S first. It will install the USB VCOM preloader driver. It will be needed by the SPFT to detect the phone. Use the provided ADB driver for the MT65xx_android_phone. If ever you get stucked in an error and your device wont boot anymore, just use One Touch Upgrade and your phone will be as good as new...
Guide: CWM/TWRP recovery
1. Download MTK Droid Root & Tools & SP Flash Tools, ADB Drivers, One Touch Upgrade S, and the Root script. Extract them anywhere in your computer.
2.Install ADB driver.This step is now optional to get adb working. You can now skip to step 5 if you just want to get rooted with CWM/TWRP recovery installed.. In your phone, go to Settings>Development. Set to on and check USB debugging.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3. Connect device to PC. Driver will fail to install (thats normal). Install UniversalAdbDriverSetup6.msi
Note: in Windows 8, this will pop-up. do this:
4. After installing the Universal ADB driver, go to device manager of your computer. Follow the images as descirbed.
ADB commands should work now (if you have ADB installed) and you won't have any problems about MTK droid tool not detecting phone.
5. Be sure that you have already installed One Touch Upgrade S before this step. Open SP Flash tool and select the scatter file by clicking on the Scatter-loading button.
6. UNCHECK BOOT and leave RECOVERY checked. Disregard what is on the photo. There's are reports that the latest firmwares are incompatible with the uploaded patched boot.img.
Note: By default, the CWM recovery will be selected in the SP Flash tool. If you want the fully working TWRP-recovery (I recomment this because CWM recovery is not fully functional), just click RECOVERY and replace it with this file.
7. Click Download button. Click yes on the download warning. Turn off phone, remove battery and connect the phone (without battery) and wait until SP Flash tool detects the phone and watch as it flash the image.
8. If everything passes without errors, unplug the phone, reinsert battery and boot to recovery by pressing power + volume up.
9. You should boot in CWM/TWRP recovery. We are ready to flash the Superuser app to gain root.
Guide: Superuser
You can use mtk droid root and tools here. Just plug in phone to pc while still in CWM recovery. Run mtk tools, wait to detect phone, click superuser, then build.prop, then delete china. Your done. Or use the guide below if you have problems with it.
Using CWM recovery to flash superSU
1. While still on CWM recovery, plug the phone into PC again.
2. Navigate using volume up and down buttons. Press Power button to select and Back soft key to go back.
3. Select mounts and storage>mount USB storage.
4. Copy the root-glory-2-4030E.zip to your sdcard.
5. After copying, select unmount and go back.
6. Select install zip from sdcard>choose zip from sdcard>root-glory-2-4030E.zip and select yes - Install root-glory-2-4030E.zip
7. It will flash the app to the system including all needed binaries. I also included the fix-permissions banary which is missing from the ROM.
8. Reboot the phone and wait. It will boot normally and no data will be lost. You will see superuser app in your app drawer. You are now rooted!:thumbsup:
Using TWRP recovery to flash superSU
1. While still on TWRP recovery,Connect the device to PC.
2. Tap mount in the screen then Mount USB storage.
3. Copy the root-glory-2-4030E.zip to your sdcard.
4. Press back on your device softkeys.
5. Tap install and select root-glory-2-4030E.zip
6. Wipe to confirm flash.
7. Reboot>System.
8 You're done.
Screenshots:
Guide to Unroot
Requirements:
1. Windows Based PC
2. SP flash tool (included in OT-4030 ROOT&CWM RECOVERY)
3. Stock recovery.img
4. Unroot script (Unroot-glory-4030E.zip)
Urooting
1. Copy Unroot-glory-4030E.zip to the root of sdcard.
2. Reboot to CWM recovery.
3. Select install zip from sdcard>choose zip from sdcard>Unroot-glory-4030E.zip and select yes - Install Unroot-glory-4030E.zip
4. On your PC, Open SP flashtool and select the scatterfile.
5. Remove check on BOOTIMG and click RECOVERY and select the stock recovery.img. Click download button and disregard download warning by clicking yes.
6.Connect the phone to pc without battery. After the download finished dialog, your done!
Links:
OT-4030 ROOT&CWM RECOVERY
Universal ADB driver
One Touch Upgrade S
Root script
Unroot script
Stock recovery.img
Mirror to all files
TWRP-recovery

I get this error after #3 of CWM recovery installation:

warfab said:
I get this error after #3 of CWM recovery installation:
Click to expand...
Click to collapse
Please attach log...

cyberangel22k said:
Please attach log...
Click to expand...
Click to collapse
Here are my logs...

Guide updated!
added some more steps for error 4050...

Anyone still getting errors, I will help today. you can send a PM on my personal G+ so I can answer quickly to your concerns...

boot_logo changed!
tried to change the boot logo and it worked! thanks to balamu96m for his guide.
This is my new boot logo

bootanimation problem!
I changed my bootanimation and tried if it works using these commands which i normally do with my past android devices.
Code:
adb shell bootanimation
the animation works fine but when i hit:
Code:
adb reboot
the animation showed was just android mask or android shine which shows when you don't have bootanimation.zip inside /data/local or /system/media. it's like a default bootanimation.
so once I booted, I tried again
Code:
adb shell bootanimation
the bootanimation works but when I reboot, it's back to default.
I tried replacing back the original bootanimation.zip but it still the defaut bootanimation. It's very weird. I haven't encountered this before...

cyberangel22k said:
Anyone still getting errors, I will help today. you can send a PM on my personal G+ so I can answer quickly to your concerns...
Click to expand...
Click to collapse
Me and many others are still waiting for your help at symbianize...

can't access symbianize since saturday
Dito muna kayo magpost ng mga tanong.. humihingi din ako ng tulong kay rua1 re: sa error 4050.

fixed!
cyberangel22k said:
I changed my bootanimation and tried if it works using these commands which i normally do with my past android devices.
Code:
adb shell bootanimation
the animation works fine but when i hit:
Code:
adb reboot
the animation showed was just android mask or android shine which shows when you don't have bootanimation.zip inside /data/local or /system/media. it's like a default bootanimation.
so once I booted, I tried again
Code:
adb shell bootanimation
the bootanimation works but when I reboot, it's back to default.
I tried replacing back the original bootanimation.zip but it still the defaut bootanimation. It's very weird. I haven't encountered this before...
Click to expand...
Click to collapse
Found out the cause of this issue. The stock ROM has no fix_permissions binary. So I pushed the binary and tried to fix perm again and now custom bootanimation.zip works!

4050 fix
to get past the 4050 error update the SPFlash Tool to this one http://forum.xda-developers.com/showthread.php?t=1982576
To those having problems with MTKDroid not detecting their phone download and install PDANet for Windows (any version would suffice)
just rooted my phone \^0^/

[ Auxus Nuclea N1 ] - All Things Thread

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Technical Specs
[*]Google it before posting here.
[*]Please post any guides and/or tutorials directly onto the forum, rather than links, otherwise this thread will be closed by the Moderator.
Click to expand...
Click to collapse
Rooting for 8GB Version
Procedure:
1. Download the Framaroot application and transfer it to SD card
2. Now go to Settings>Security and put check mark on Unknown Soruces
3. Now use file manager and browse to the location where you have placed Framaroot Application
4. Install it and open it. Now Select "Install SuperSU" and hit Boromir.
5. Now go to Play Store and search for Super User and install it after opening it might ask to update SU.bin, hit yes and then "Normal"
6. Reboot your Device.
[ROMs]
Please do not flash the firmware that is not meant for your phone. Flash only 4gb to 4gb and 8Gb to 8Gb
Auxus Nuclea N1 Stock Firmware
NEW
Final Version - 11-Dec-2013 - [Flash with SPFlash Tools]
Click to expand...
Click to collapse
OLD ROMs
Firmware Update (Intermediate V1) 18-Nov-/2013 [Flash with spflash Tools]
NucleaN1_FirmwareUpdate_V1_CWM.zip
Click Here - - [09/Sep/2013] [Flash with SPFlash Tools]
CWM Zip Download from herehttp://d-h.st/b3r
8GB version -
Click Here - [Flash with SPFlash Tools]
Custom ROMs
Click HERE
How to Flash Stock ROM using SP Flash Tools?
1) Unzip the ROM folder
2) Install the drivers and open SP Flash Tools..
Check the below post with images, if you are not sure whether drivers are installed or not.
If you face this problem, then try Firmware upgrade and connect the phone..
You can now safely disconnect your phone and turn it on. The process ends here.
FLASHING PATCH using SP Flash Tool(Single Files)
1)Select Android Scatter File .txt ....
2)Uncheck all files from the below box....
3)Select the correct file you want Flash by clicking it....
4)Click Download button on SP tool.... **"Dont click Firmware Upgrade"
5)A box asks to confirm it...Click Yes...
6)Connect Phone without the battery...
7)It will get Flashed...[/COLOR]
[Recovery]
1) Nuclea N1 Stock Recovery Click Here
2) TWRP Recovery- Click HereThanks to Kumar abhishek
3) CWMRecovery 6.0.3.3 Click Here or Click Here Thanks to C3C076
Procedure to Flash Recovery.
1) Download Mobile uncle tools from play store
2) Place the downloaded recovery.img in your sdcard
3) Open Mobile uncle tools
4) Select 'update recovery' and Click on the recovery.img
5) Reboot
adb method: For advance users:
---------------------------------------------------
Make sure you have all the drivers for your phone installed on your computer.
Make sure you have USB Debugging enabled, Install from Unknown Sources is enabled and device is detected in ADB run this command:
Code:
adb devices
Download the CWM Recovery
Press SHIFT key + Right mouse click in the folder where the file is located and select Open Command from Here.
Now, in the command prompt do the following:
a. Reboot into Bootloader mode. Use command:
Code:
adb reboot bootloader
b. Device will reboot and display logo. (check if device is in bootloader mode by running command:
Code:
fastboot devices
. If you see a device connected then you have successfully rebooted into fastboot mode.
c. Now, run this command:
Code:
fastboot flash recovery recovery.img
(This will flash the CWM recovery image to the device).
d. Once successful, reboot the device using this command:
Code:
fastboot reboot
.
How to Backup ur complete ROM
1. In CWM Recovery mode, select Backup and Restore
2. Select Backup
3. Wait till it finishes (May take upto 10 minutes)
How to restore ur backed up ROM from SD card
1. Go to CWM Recovery, select backup and restore
2. Select Restore
3. select the folder in date format (Folder name indicates the time and date when ur backup was created}
4. Wait till it finishes (May take upto 10-15 minutes)
Special Guides for Newbies to get Started
Everything you need to know about Clockworkmod Recovery
How to setup ADB and Fastboot properly
5 Things Every Android user should do
24 Apps Every Android User Must Install
5 Things to know before performing any Android tweak
Thanks to Driodiser
HIT THANKS PLEASE BECAUSE IT WONT COST ANY :angel:

Extend your storage on Nuclea N1
[Extend your storage on Nuclea N1] - Thanks to @kailashnj
Follow the instructions in the post HERE
How to enter into Recovery - Nuclea N1 :-
Code:
[LIST=1]
[*]Turn OFF your phone.
[*]Press & hold Vol(+) button and Power button for 12 seconds.
[B]Stock Recovery[/B]
[*]You will see a laid-down Android symbol with 'No command' message below it. Press the power button once.
[*]You will enter into menu 'Android System Recovery'
[*]Press Vol(-) to roll over options.
[*]Press Vol(+) button to select.
[*]DONE!
[/LIST]
Another options if you are facing trouble going to recovery:
Code:
1. Install Mobile Uncle tool
2. Reboot recovery.
MTK6589 Drivers
Universal Pdanet drivers Click Here
Follow this guide Here
Tools
MTK Android PC Sync Tool V2.1233.1 Click Here
SN_Write_tool_exe_v2.1132.0.rar - 8.27 MB
Guide Here
Driver_Auto_Installer_v1.1236.00 Click here

Meta-Mode is very useful if device fails to get detected by PC under normal Conditions.....To make device fall to Meta-Mode,just do these :
1) Start SP Tool on PC..
2) Now run SP Tool with "Firmware Upgrade/Download"
3) Switch OFF Phone..
4) Remove Battery..
5) Connect mobile to PC while holding Volume + button [WITHOUT BATTERY]..
6) Flashing will be started
7) Hold the button till flashing completes...
After 100% Flash,Release Button..
9) Insert Battery..
10) Start Device.
Click to expand...
Click to collapse
How to dump stock recovery image using SP Flash Tool
1) Download and install USB VCOM Driver
2) Download, extract and launch SP Flash Tool
3) Use "Scatter-loading" button to load attached scatter file: MT6589_Android_scatter_emmc.txt
4) Download stock recovery image and place inside the ROM folder. Then select only RECOVERY.
5) Turn off your phone. Make sure USB cable is unplugged. Wait until vibrator indicates it's turned off
6) Click Download button in SP Flash tool, confirm warning complaining about not all files being selected
7) Connect your phone and wait for the flash process to finish (indicated by window with green circle)
8) Unplug USB cable. Hold down Volume+ while turning your phone on to boot into recovery
Click to expand...
Click to collapse
Backing up your IMEI
Different Methods are available for this.
1) Use any RootExplorer to copy file /data/nvram/md/NVRAM/NVD_IMEI/MPOB_001 to your external SD card. (or if that folder does not exists, try /nvram/md/NVRAM/NVD_IMEI/MPOB_001). It is good to backup the entire folder /data/nvram/md/NVRAM.
2) Back up using Mobile Uncle utility. Click on Mobileuncle Tools --> Click IMEI Backup Restore (MTK) --> Backup/Restore
Restore your IMEI
Code:
1- Open Mobile Uncle Tools.
2- Goto Engineer Mode
3- Select Engineer mode[MTK]
4- Under Connectivity Tab go to CDS information
5- Select Radio Information
6- Select Phone1 (for the first imei)
7- at the top there is a command line which begins “AT+” just type there “AT +EGMR=1,7,”IMEI_1? (instead of IMEI_1 put your first imei number)
8- hit send command
9- You will / may get a confirmation that "sent to mSend".
10-Now come back and select “Phone2?
11-at the top there is a command line which begins “AT+” just type there “AT +EGMR=1,10,”IMEI_2? (instead of IMEI_2 put your second imei number)
12-Then just reboot the phone.
13- Dial ” *#06#” to Check Imei.
Factory ROM Backup for MT65xx via MTK Droid Root & Tools For BackUp & Unbrick
It's tested and working...
How to install ADB USB driver in window 7
use this method also in window xp,if any driver not install
Google USB Driver Rev 7 ( ADB driver )
inside three dll file driver
1-WdfCoInstaller01009.dll
2-winusbcoinstaller2.dll
3-WUDFUpdate_01009.dll
link
Click Here
Before use it is necessary to check that:
adb drivers are installed. Check device manager--> unknown devices. ADB Drivers attached.
Now the Tool
Credits: umesh gaba
[MOD][4.1 4.2] Extend Phone Storage 1.5, 2.5GB A116 (Other MT6589 Devices on request)
[Solution] NVRAM WARNING: Err = 0x10
Download this zip Click Here
Prerequisites:
You have to backup IMEI of your phone (both sim slot).
Step 1 - Extract the WiFi Fix files and place them in a folder on your memory card
Step 2 - Open Root Explorer
Step 3 - Click on Mount R/W
Step 4 - Click on data
Step 5 - Scroll down to the folder named nvram
Step 6 - Open APCFG folder
Step 7 - Open APRDEB folder
Step 8 - Delete the WIFI and WIFI_CUSTOM files
Step 9 - Now copy/move the files on your sdcard to data/nvram/APCFG/APRDEB and Paste
Step 10 - After pasting both the files, close Root Explorer and REBOOT your phone.
Here is another method Click Here
The bad news is.

Vijay have u bot the mobile..
Sent from my AUXUS Nuclea N1 using xda app-developers app

can you provide a review of the phone?
akashavel said:
Vijay have u bot the mobile..
Sent from my AUXUS Nuclea N1 using xda app-developers app
Click to expand...
Click to collapse
Hello dude,
i have booked this phone, and i am seriously waiting for some reviews.
It would be great if there was a video review done by you on you tube or where ever you are comfy.
The specs are awesome but there are some negative opinions as well.
This would help.
Thanks

akashavel said:
Vijay have u bot the mobile..
Sent from my AUXUS Nuclea N1 using xda app-developers app
Click to expand...
Click to collapse
Yes, I am in batch II.

dhavalg said:
Hello dude,
i have booked this phone, and i am seriously waiting for some reviews.
It would be great if there was a video review done by you on you tube or where ever you are comfy.
The specs are awesome but there are some negative opinions as well.
This would help.
Thanks
Click to expand...
Click to collapse
videos posted by me..
https://www.youtube.com/user/akashavel/videos
also chk this fb page
https://www.facebook.com/groups/Ibe...39765010250/?ref=notif&notif_t=group_activity

Hi Guys,
Even I have bought this phone and awaiting delivery, I was promised by 4th Aug. Lets see. The specs of this phone seems to be great other than the 4GB storage. I hope that apps2sd works really fine and I am able to store all my game data on the SD card. Wanted to know more info of this phone and the rom.
Regards,
Kailash

can't decide what to buy
is the costumer service good...i am really thinking to buy this phone but this brand was never heard before by me.....
in ur opinion which phone would be better
1. canvas 4 (micromax)
2. auxus nuclea n1 (iberry)
3. Xolo play (XOLO)

Thanks...
akashavel said:
videos posted by me..
https://www.youtube.com/user/akashavel/videos
also chk this fb page
https://www.facebook.com/groups/Ibe...39765010250/?ref=notif&notif_t=group_activity
Click to expand...
Click to collapse
That was really helpful, but i hoped some words about the phone from your mouth as well.
Need some comparison too,
But any ways it was awesome....I am going to continue with my order, actually i was planning on cancelling it. But now not...
Thanks for the videos.
Hope we get roms for it as well.

:victory: Yesss... XDA Thread for Auxus Nuclea.. feeling exciting.. Best Wishes, Guy.. :good::good:

dhavalg said:
That was really helpful, but i hoped some words about the phone from your mouth as well.
Need some comparison too,
But any ways it was awesome....I am going to continue with my order, actually i was planning on cancelling it. But now not...
Thanks for the videos.
Hope we get roms for it as well.
Click to expand...
Click to collapse
only thing is RAM so many apps consumes more memory .waiting for tweaked ROM.other than that the phone is gud..

I prefer to use Titanium Backup to freeze unwanted app rather to uninstall.. this app will save lots of RAM..

without source kernals cant we install custom Roms or stock roms, iam newbie to these things, i have a doubt, i have seen so many custom ROMs for samsung devices that means have samsung provided the source kernals???? please reply any experts

Without kernel source who would buy this phone and on top of that its Chinese brand better buy micromax Indian brand.....

ashok20205 said:
without source kernals cant we install custom Roms or stock roms, iam newbie to these things, i have a doubt, i have seen so many custom ROMs for samsung devices that means have samsung provided the source kernals???? please reply any experts
Click to expand...
Click to collapse
Yes, We can install Custom ROMs (Themed ROMs or Ported ROMs). But, with kernel sources a lot of development can happen. :good:

akashavel said:
only thing is RAM so many apps consumes more memory .waiting for tweaked ROM.other than that the phone is gud..
Click to expand...
Click to collapse
No need to wait for a Custom ROM. You can try One-Power-guard app, Clean master and Greenify app's.

Chris s5830i said:
Without kernel source who would buy this phone and on top of that its Chinese brand better buy micromax Indian brand.....
Click to expand...
Click to collapse
This mobile is good at it price with the spec's. Even Micromax is not providing kernel sources. Also, compared to the support of Micromax, iBerry is doing best.

abhiek bist said:
is the costumer service good...i am really thinking to buy this phone but this brand was never heard before by me.....
in ur opinion which phone would be better
1. canvas 4 (micromax)
2. auxus nuclea n1 (iberry)
3. Xolo play (XOLO)
Click to expand...
Click to collapse
Check the facebook page. Then you can decide

Can you post link for CWM for nuclea N1
can you help me with the link for CWM

[Discussion][Guide][Root] Alcatel one touch 4037A/N/One Touch Evolve 2

[GUIDE] How to flash CWM or TWRP recovery and root your device!
Disclaimer: Your warranty is now void. You do this in your own risk. I do not take any responsibility to your device.
Credits: This root method was found from a facebook group that uses this phone, i am just posting it here. Give thanks to Eduardo Perez!
I ported TWRP recovery for this device and Eduardo did the CWM recovery. Also thank rua1 from XDA for his MTK droid tools. Koush for his driver installer.
USERS OF 4037N/T or any other model that is from T-Mobile, DO NOT TRY ANY OF THE RECOVERIES HERE. NOR TRY TO MOD IT IN ANY WAY. YOU WILL BRICK YOUR DEVICE.
See post #68 for more info
Notice for T-Mobile owners (4037N)(MetroPCS) Users!!
Requirements:
1. A windows PC
2. Universal ADB driver
3. ROOT ALCATEL 4037N 4.4.2 zip file
Instructions:
1. Download the ROOT ALCATEL 4037N 4.4.2 zip file here and extract it anywhere on your desktop.
2. Go inside the extracted folder and extract iRoot zip file and install iRoot. Disable any antivirus you may have or User Account Control(UAC).
3. After installing iRoot, go to your phone and enable USB debugging. Look up how to enable it on google if you don't know how to.
4. Run iRoot as administrator and then connect your phone.
5. Wait until it detects it and then press the root button and your phone will be rooted.
If you want to see a video of the rooting check here
BACKUP YOUR DEVICE BEFORE DOING ANYTHING IN THE EVENT SOMETHING GOES WRONG. BACKUP TUT HERE
Requirements:
1. A windows PC
2. SP flash tools
3. CWM or TWRP recovery
4. Universal ADB driver
5. MTK preloader driver
VIDEO TUT By nashj1975
https://www.youtube.com/watch?v=xNWALNB9M-Q
[GUIDE] FLASH CWM/TWRP
1. Download the attached files below and extract them anywhere on your computer, then download the FLASHTOOLS and SP FLASHTOOL folder here and extract them.
2. Go to this link to get the drivers specifically for your phone. Install the program after the download is complete.
3. Go to the FLASHTOOLS folder and extract Driver_Windows_MTK_Preloader drivers and then go to auto install and install the drivers. This is for the preloader drivers which will be used later.
4. Install ADB driver by going to the Flash Tool folder and then adb folder, then locate the adb file and run it as administrator. Go to settings, then development if you don't see development go in about and click on the build number 7 times to enable development mode. Enable USB debugging.
5. Open the SP flash tools folder and run flashtool.exe as administrator.
6. If anything pops up just ignore it and click ok.
7. Go to option then connection and make sure auto detect is selected.
8. Go to scatter loading and click it, locate the scatter file from the extracted folder and open it.
9. When it opens click on the recovery option and click the check box.
10. Decide which recovery you want and rename it to recovery.img.
11. Click on the location in the same recovery option and choose your recovery.img
12. Turn off your phone and take out the battery.
13. Click on Download and then connect the phone to the PC.
14. If you did everything i said above, it will flash your chosen recovery.img and you will have a custom recovery.
[GUIDE] ROOT/Superuser
1. Reinsert the battery and turn on the phone.
2. Go to the alcatel 4037 folder that you extracted.
2.Place the root_grouper-tilapia_4.4_update.zip and superuser.zip on your sdcard or internal storage. ( If these root files don't work, just download the UPDATE-SuperSU-v2.46.zip and flash that.)
3. Turn off the phone and boot it into recovery mode.
4. Navigate using the volume keys for CWM recovery or just use touch for TWRP. Use the power button to select.
5.Select install zip from sdcard and choose zip from sdcard. Locate the zip files that you sent.
6. Flash the root_grouper-tilapia_4.4_update.zip first then flash the superuser.zip
7. Reboot your phone and there you go. Root Access
OR
ROOT YOUR PHONE USING THE 360 ROOT Chinese apk attached below.
Copy the 360ROOT.apk to your sdcard either internal or external.
Install it and then follow the screenshots below to see how to root.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Yeah i know it says 4032A but it was just to show you how to use it.
After clicking on root your phone will be rooted. P.S You need an internet connection for the root apk to work.

How to unroot
This is a guide for unrooting your device. Download universal unroot from the play store, or look for an apk file.
Install it and bam you're unrooted.

How to make a backup of your device
There are many ways to back up your phone. Some are better than some but you can decide which you want to use.
1. Using recovery . Boot into recovery mode and select backup.
2. Using Mtk droid tools. Connect your device to the PC with usb debugging enabled. Run mtk droid tools as administrator and wait for it to load. Click on the root,backup and recovery tab. Select backup.
3. Using SP flash tool. This is recommended for those who don't yet have root on their device. There is an original post for this method from rua1 here

How to unbrick your device
Unbricking can be done using the One touch upgrade tool from the alcatel website http://www.alcatelonetouch.com/global-en/products/smartphones/pop_d3.html#.VLbhTiwYGzU
1. Download the Mobile Upgrade S 4.2.7 upgrade tool and install it
2. Turn off your device and take out the battery.
3. Reinsert the battery and open the tool.
4. Select your device from the drop down menu 4037 and follow the instructions from the tool.

I am trying to root the fierce 2 but it doesnt seem to flash the twrp recovery even though I am sure I did everything right! Nothing happens at the last step where you said to take out the battery then click download and connect the phone to the PC. Nothing happens the phone just shows the Actel logo and then vibrates and turns of then back on over and over. Any ideas?
Note I did not do step 5

GhostSamuraiX said:
I am trying to root the fierce 2 but it doesnt seem to flash the twrp recovery even though I am sure I did everything right! Nothing happens at the last step where you said to take out the battery then click download and connect the phone to the PC. Nothing happens the phone just shows the Actel logo and then vibrates and turns of then back on over and over. Any ideas?
Note I did not do step 5
Click to expand...
Click to collapse
Use my unbricking method to restore your device, and i don't think Step 5 should be a problem.

Phones not in boot loop it works fine. Just nothing happens when I click download and connect the phone without the battery.

check your pm :good:

sweet my buddys been missing having root since he upgraded from the evolve, even better that there is a custom recovery.
whats the facebook group page cant seem to find it.

https://www.facebook.com/groups/556165774484796/ this is the link to the group on facebook...note the facebook group is in spanish tho so if you want you can use google chrome and let automatic translation do the work for you

Hi..thanks for ur guide...
I'm succesful root my 4035x
Sent from my 4035X using XDA Free mobile app

xmanner77 said:
Hi..thanks for ur guide...
I'm succesful root my 4035x
Sent from my 4035X using XDA Free mobile app
Click to expand...
Click to collapse
great happy that i helped :good:

---------------------

Thread updated!!
Thread is updated with a video showing how to root the phone @Altnot

New Video
New video showing how to root is coming soon! Thanks to junior member @nashj1975. :highfive:

Stock ROM
--

Thanks to OP. Successfully flashed CWM and rooted my OT 4035D (Alcatel One Touch Pop D3 with KitKat 4.4.2). Was unsuccesful with Towel Root, Framaroot and Kingo Root, but this did the trick! I already clicked your thanks button.

CVAngelo said:
Thanks to OP. Successfully flashed CWM and rooted my OT 4035D (Alcatel One Touch Pop D3 with KitKat 4.4.2). Was unsuccesful with Towel Root, Framaroot and Kingo Root, but this did the trick! I already clicked your thanks button.
Click to expand...
Click to collapse
Nice glad i could help

Hi
Thanks

abdullah.alhossain said:
Thanks
Click to expand...
Click to collapse
You're welcome

[Guide] How to Root Cube T8 Plus

Hi
I found a russian site how to root the Cube T8 Plus h**p://4pda.ru/forum/lofiversion/index.php?t695306.html. Here a short translation:
Disclaimer: ******* I'm not responsible for any damages *******
1. Download SuperSu directly to your Cube T8 from official site: h**p://download.chainfire.eu/supersu
2. Download Flash Utility/Driver on your PC: h**p://uploaded.net/file/eyo5yt8c
3. Download TWRP for Cube T8 on your PC: h**p://uploaded.net/file/o54jinin and extract its content to a folder.
Mirror: https://drive.google.com/drive/fold...ourcekey=0-11J8nUVn2_sUUAPHA9kwWg&usp=sharing
4. Install Device Driver from Step 2. on your PC (you have to agree Security warning). Depending on Windows version used, disabling Driver Signing might be required prior installation.
5. Start flash_tool.exe
6. Go to "Download" tab and Click "Scatter-Loading" Button, move to folder created in Step 3. and select the file "MT6753_Android_scatter.txt". Press the "Download" Button
7. Power down your Cube T8 tablet. After power down, connect it to a USB Port on your PC (No, you don't need to power it up - leave it powered down!). After a few moments, the flash tool should recognise the tablet and will install twrp recovery and should show "Success" Screen
8. Remove tablet from PC. Boot into Boot Selection by pressing Volume-Up and Power button simultaneously, Select "Recovery" and wait for twrp booting up.
9. In twrp, Install Zip File downloaded on Step 1. This should be found in Folder "MyFavorite"
10. Reboot device. By selecting "Reboot" in twrp, the device will hang. But don't worry; just press the power button for about 10 seconds for a forced reboot.
11. Voilà, you have a rooted Cube T8 Plus

Thanks for the guide. Can you provide more mirror? Uploaded is currently blocked in my country. Google Drive would be sweet.
Thanks.

Anybody tried this?

It works perfectly, but I had to disable the driver's signature check.
Now I just need the modified scatter file to get a better memory repartition. These russian guys on pda.ru found out how to repartition the memory, but the file is now disappeared from internet http://4pda.ru/forum/index.php?showtopic=695306&st=560#entry44767726

Yes !
it worked for me but i didnt succeed in installing the right driver (package given in this post was correctly installed) for tablet in off mode,
so i had to force download of recovery and if SuperSU install (with error) when i launch it it warn for binary installation.
but root is effective and i can now use soft like adaway or else that need complete root access :victory:

LtGarcia said:
it worked for me but i didnt succeed in installing the right driver (package given in this post was correctly installed) for tablet in off mode,
so i had to force download of recovery and if SuperSU install (with error) when i launch it it warn for binary installation.
but root is effective and i can now use soft like adaway or else that need complete root access :victory:
Click to expand...
Click to collapse
That's weird, it worked flawlessly for me.
By the way, the internal 2 GB storage is way to small for me, I need a bigger partition and since the 4pda guys deleted their scatter files, I'm trying to create it by myself following this guide, I hope to not mess up things
Ok, I found the scatter editor (that was deleted too). Here you can download it. OP, if you want, you can add it in the guide.

Thanks for your feedback and your work Dyonysus, i assume all errors was consecutive to Kingroot installation (he didn't succeed in rooting but i left it installed when i flashed the recovery as i checked sometmes if a root policy was avaible)

This root guide can be used for Cube T8 also?

I also confirm this method works perfectly. Good job finding this.

Dionysus2389 said:
By the way, the internal 2 GB storage is way to small for me, I need a bigger partition and since the 4pda guys deleted their scatter files, I'm trying to create it by myself following this guide, I hope to not mess up things
Ok, I found the scatter editor (that was deleted too). Here you can download it. OP, if you want, you can add it in the guide.
Click to expand...
Click to collapse
So, have you succeeded in repartitioning the internal memory? If yes, did you face any issues or errors in the process and is the device stable and working as fast afterwards?

vorlonresident said:
So, have you succeeded in repartitioning the internal memory? If yes, did you face any issues or errors in the process and is the device stable and working as fast afterwards?
Click to expand...
Click to collapse
Unfortunately I didn't. I got a bunch of problems tryin' to forge the new scatter file and, when I finally got a decent one, the damn tool didn't flash it properly.
If someone could find those two files or just ask those russian guys to upload them again, it'd be terrific.

Hi,
This post is a subject to change (grow), since I will keep it as a record for my tips for this fine tablet.
Installation of TWRP recovery and increasing /data partition (YES! That's possible)
I've succeeded getting TWRP, root and larger /data partition, so after screenshot I'll put detailed how-to. Sorry for duplicating first post, but I'd like to have everything in one place in the way I exactly did it.
Warning: this method seems to be blocked in some newer OS updates, see this post for reference: http://forum.xda-developers.com/showpost.php?p=64801688&postcount=25
All credits go to OP and @odigitech for http://forum.xda-developers.com/general/rooting-roms/guide-how-to-resize-data-internal-t3180978
Screenshot:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
You need SD card for that.
Cube T8 Plus TWRP and root:
1. Download SuperSu and copy it to the root of SD card (without extracting): http://download.chainfire.eu/supersu
2. Downlad Utility/Driver to PC: http://uploaded.net/file/eyo5yt8c
3. Download Cube T8 TWRP recovery to PC: http://uploaded.net/file/o54jinin and unpack.
4. Install driver on PC. Depending on Windows version, if the driver installation fails, it may be necessary to disable signature check (google for that).
5. Run flash_tool (downloaded in step 2). If it doesn't run, try copy it to the root folder of your hard drive, eg. C:\SP_Flash_Tool_exe_Windows_v5.1516.00\, albo D:\SP_Flash_Tool_exe_Windows_v5.1516.00\
6. In "Download" section choose "Scatter-Loading" point to "MT6753_Android_scatter" from /Recovery (downloaded in step 3), press "Download" button.
7. Turn off the tablet. Connect it via USB to PC (tablet needs to be switched off!). After short while, flashing tool should recognize the tablet and start flashing automatically, installing TWRP recovery. After that you should get "Success" screen.
8. Disconnect tablet from PC. Run it in Recovery by pressing VOLUME_UP and POWER simultanously.
9. Using VOLUME_UP, choose "Recovery" and confirm it by pressing "VOLUME_DOWN". Wait untill TWRP starts.
10. In TWRP choose 'install ZIP' and point to "/external sd/UPDATE-SuperSU-v2.46.zip"
11. After installation is finished, choose "Reboot". Recovery will hang, but do not fear Press Power for 10s to force turn off. Then turn on the tablet.
Your tablet is now rooted!
Change partition size:
1. Download and copy to the root of SD (without extracting) Resize_v22.4.1-signed.zip: (take attachment from the first post here: http://forum.xda-developers.com/general/rooting-roms/guide-how-to-resize-data-internal-t3180978/ )
2. Run the tablet in Recovery by pressing VOLUME_UP and POWER simultanously.
3. Using VOLUME_UP, choose "Recovery" and confirm it by pressing "VOLUME_DOWN". Wait untill TWRP starts.
4. In TWRP choose 'install ZIP' and point to "external sd/Resize_v22.4.1-signed.zip""
5. In one of following windows choose the partition size. I recommend between 8GB and 10GB. WARNING: If you choose less than the current size, you may loose your data. More than or equal to 8GB is a safe value.
Enabling Multiuser accounts:
1. The device must be rooted
2. Use any root explorer to edit /system/build.prop.
3. Add to the end of a file:
Code:
fw.show_multiuserui=1
fw.max_users=5
4. Reboot
Info: After first try to swich to guest the device force rebooted, but then it worked well.
Disabling killing background apps
If you encounter situation in which apps are being killed right after they are put to background (each application switch using recent apps causes application reinitialization), just make sure that Developer Options/Apps/Don't keep activities is switched off!
Permamently disabling pre-installed chinese apps (they will not reappear after full reboot)
There are 6 chinese apps pre-installed, which can be easily disabled. You can try to simply uninstall them, but you'll find that after full reboot they reappear.
So the best way to disable them is to use any root explorer and get rid APKs in /system/vendor/operator/app. I myself renamed app folder to app.old. They do not appear anymore.
What to do if tablet seems to be dead (black screen - no reaction), but it just misbehaves
Couple of times I've had a situation in which the screen was blank and I couldn't wake up the device. I could however run recovery, so the first time I performed reset from recovery and it helped.
Next time I found out that it's automatic brightness that fails and causes the screen to go blank. So the solution is to press power button, make a swipe gesture from the top to show brightness slider (you will not see it, but it works even on the lockscreen), and try to blindly press this slider. It should be about 2,7 cm (1,06 inch) from the top, with ca. 3cm (1,2 inch) margins on the left and right. Then stop using autobrightness with slider set to zero.

Thanks a ton
Amazing , followed your instructions and my tablet is now rooted and also has 9+GB of data partition. Thanks a ton.. Keep up the good work.
--Rao:

after using the resize script it not remount the partition and android not start. Android ask for a password to "decrypt data" but the problem is that the partition is missing.
Any suggest about this?
thanks
For the moment i can resize partition up to 6 gb using a edited scatter file

Please can I use this safely on the original Cube T8?

Zunera M said:
This root guide can be used for Cube T8 also?
Click to expand...
Click to collapse
The steps are the same! Only the files for drivers and TWRP Recovery change. I need to put a guide together for the T8.
Here's the link: http://forum.xda-developers.com/android/general/guide-how-to-root-original-cube-t8-t3285009

maludroid said:
Hi,
I've succeeded today getting TWRP, root and larger /data partition, so after screenshot I'll put detailed how-to. Sorry for duplicating first post, but I'd like to have everything in one place in the way I exactly did it.
All credits go to OP and @odigitech for http://forum.xda-developers.com/general/rooting-roms/guide-how-to-resize-data-internal-t3180978
Screenshot:
You need SD card for that.
Cube T8 Plus TWRP and root:
1. Download SuperSu and copy it to the root of SD card (without extracting): http://download.chainfire.eu/supersu
2. Downlad Utility/Driver to PC: http://uploaded.net/file/eyo5yt8c
3. Download Cube T8 TWRP recovery to PC: http://uploaded.net/file/o54jinin and unpack.
4. Install driver on PC. Depending on Windows version, if the driver installation fails, it may be necessary to disable signature check (google for that).
5. Run flash_tool (downloaded in step 2). If it doesn't run, try copy it to the root folder of your hard drive, eg. C:\SP_Flash_Tool_exe_Windows_v5.1516.00\, albo D:\SP_Flash_Tool_exe_Windows_v5.1516.00\
6. In "Download" section choose "Scatter-Loading" point to "MT6753_Android_scatter" from /Recovery (downloaded in step 3), press "Download" button.
7. Turn off the tablet. Connect it via USB to PC (tablet needs to be switched off!). After short while, flashing tool should recognize the tablet and start flashing automatically, installing TWRP recovery. After that you should get "Success" screen.
8. Disconnect tablet from PC. Run it in Recovery by pressing VOLUME_UP and POWER simultanously.
9. Using VOLUME_UP, choose "Recovery" and confirm it by pressing "VOLUME_DOWN". Wait untill TWRP starts.
10. In TWRP choose 'install ZIP' and point to "/external sd/UPDATE-SuperSU-v2.46.zip"
11. After installation is finished, choose "Reboot". Recovery will hang, but do not fear Press Power for 10s to force turn off. Then turn on the tablet.
Your tablet is now rooted!
Change partition size:
1. Download and copy to the root of SD (without extracting) Resize_v22.4.1-signed.zip:
2. Run the tablet in Recovery by pressing VOLUME_UP and POWER simultanously.
3. Using VOLUME_UP, choose "Recovery" and confirm it by pressing "VOLUME_DOWN". Wait untill TWRP starts.
4. In TWRP choose 'install ZIP' and point to "external sd/Resize_v22.4.1-signed.zip""
5. In one of following windows choose the partition size. I recommend between 8GB and 10GB. WARNING: If you choose less than the current size, you may loose your data. More than or equal to 8GB is a safe value.
Click to expand...
Click to collapse
Hi man Happy New Year . Can you upload again Resize_v22.4.1-signed.zip for Cube T8 Plus because the link not working....thanks

alex22280 said:
Hi man Happy New Year . Can you upload again Resize_v22.4.1-signed.zip for Cube T8 Plus because the link not working....thanks
Click to expand...
Click to collapse
I've taken the link from the first post here: http://forum.xda-developers.com/general/rooting-roms/guide-how-to-resize-data-internal-t3180978/ - see attached files, to get a correct link. I wouldn't reupload this. It looks like x-d is rotating attachment links.
Please edit your quotation so it does not contain wrong link.

maludroid said:
I've taken the link from the first post here: http://forum.xda-developers.com/general/rooting-roms/guide-how-to-resize-data-internal-t3180978/ - see attached files, to get a correct link. I wouldn't reupload this. It looks like x-d is rotating attachment links.
Please edit your quotation so it does not contain wrong link.
Click to expand...
Click to collapse
Resize_v23-signed.zip ?

alex22280 said:
Resize_v23-signed.zip ?
Click to expand...
Click to collapse
I assume it works as well...

[Guide] How to Root Original Cube T8 and Resize partition

Before we begin, this a guide written by a noob for noobs
Disclaimer; I'm not responsible if you fry your device. Just follow this guide assiduously and you should be fine
Click to expand...
Click to collapse
What you will need;
1. A Cube T8 Phablet with an SD Card
2. A Windows PC (version 7, 8, 8.1, 10 should do)
3. Common Sense
PROCEDURE:
1. Download SuperSU from the Chainfire site and transfer to the root of the SD Card WITHOUT extraction
2. Download and Install MediaTek VCOM drivers . This Youtube Video will help you guide you through the driver installation process.
NB: Depending on your version of Windows, you may need to disable driver signature check. This guide did just that for me on my Windows 10
3. After successfully installing the driver, download the latest version of SPL Flashtool and extract that folder to somewhere like \Desktop
4. Download TWRP Recovery T8 and extract to your \Desktop as well
5. Run flash_tool (which you downloaded in Step 3). If it doesn't run, try and copy it to the root folder of your hard drive, eg. C:\SP_Flash_Tool_exe_Windows_v5.1524.00\, albo D:\SP_Flash_Tool_exe_Windows_v5.1524.00\
6. In "Download" section choose "Scatter-Loading" point to "MT6753_Android_scatter" from /TWRP Recovery folder on the desktop (downloaded in Step 4), press "Download" button.
NB: if you did everything correctly you should see that recovery pane in the dialogue box has been checked
7. Turn off the tablet. Connect it via USB to PC (tablet needs to be switched off!). After short while, flashing tool should recognize the tablet and start flashing automatically, installing TWRP recovery. After that you should get a "Successful" dialog box
8. Disconnect tablet from PC. Run it in Recovery by pressing VOLUME_UP and POWER buttons simultaneously.
9. Using VOLUME_UP button, select "Recovery" and confirm it by pressing VOLUME_DOWN button. Wait until TWRP Recovery starts.
10. In TWRP Recovery, select "Install ZIP" and point to "/external sd/UPDATE-SuperSU-v2.46.zip" (which we downloaded and placed on the root of the SD Card in Step 1)
11. After installation is finished, select "Reboot". Recovery will reboot the device.
12. After the device has rebooted successfully, you should see a new app named SuperSU in the application drawer.
Boom you have successfully rooted your device if you see the app! If you didn't see this app, you did something wrong and need to repeat the process
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
RESIZING OF THE PARTITION
This was the main reason why I wanted to root the T8 so badly as I was limited to only 2.9GB of internal storage.
1. Download Resize_v22.4.1-signed.zip and copy to the root of SD (without extracting)
2. Turn the device off and run Recovery by pressing VOLUME_UP and POWER button simultaneously.
3. Using VOLUME_UP button, select "Recovery" and confirm it by pressing "VOLUME_DOWN" button. Wait until TWRP Recovery starts.
4. In TWRP Recovery, select 'install ZIP' and point to "external sd/Resize_v22.4.1-signed.zip"
5. In one of following windows that pop up, select the partition size you desire. I went with 9GB and lost only the apps that I had moved manually to the SD Card.
Here's proof of my new 9GB internal storage after resizing:
Have fun!

Really interesting Thank you for this Information!

Krystyna said:
Really interesting Thank you for this Information!
Click to expand...
Click to collapse
You are welcome!

Can you tell if this would work on New Cube T8 Plus Ultimate?
Thanks un advance
Enviado desde mi bq Elcano mediante Tapatalk

Please anyone knows if this would work on T8 plus?
Enviado desde mi bq Elcano mediante Tapatalk

Hello , I follow all the steps and when i am to step 6 and press download , nothing is downloading , i put tablet to usb and message me installation wrong.

bolija said:
Please anyone knows if this would work on T8 plus?
Enviado desde mi bq Elcano mediante Tapatalk
Click to expand...
Click to collapse
Use this tutorial for the T8 Plus;
http://forum.xda-developers.com/android/general/guide-how-to-root-cube-t8-plus-t3256490

jimfizz said:
Hello , I follow all the steps and when i am to step 6 and press download , nothing is downloading , i put tablet to usb and message me installation wrong.
Click to expand...
Click to collapse
it doesn't really download anything per se. It just downloads to the tablet after you turn it off and connect to the PC

Still something wrong
garzie2000 said:
it doesn't really download anything per se. It just downloads to the tablet after you turn it off and connect to the PC
Click to expand...
Click to collapse
Thank you for your response but still something wrond and i can not complete root.
In step 6 In "Download" section choose "Scatter-Loading" point to "MT6753_Android_scatter" mine scatter loading had MT6735M. I press downloading and continue step 7.
Flashtool start work and get a message box " PMT changed for the ROM; it must be downloaded. I press OK and nothing happened
In step 8 - 9 After choose recovery i went to a menu and there is not any choice install zip. I press reboot and back again here. What i make wrong my friend?
Regards,Dimitris

jimfizz said:
Thank you for your response but still something wrond and i can not complete root.
In step 6 In "Download" section choose "Scatter-Loading" point to "MT6753_Android_scatter" mine scatter loading had MT6735M. I press downloading and continue step 7.
Flashtool start work and get a message box " PMT changed for the ROM; it must be downloaded. I press OK and nothing happened
In step 8 - 9 After choose recovery i went to a menu and there is not any choice install zip. I press reboot and back again here. What i make wrong my friend?
Regards,Dimitris
Click to expand...
Click to collapse
That's weird please make sure that you download the files from this thread and not google and that you have the Original Cube T8 running the latest firmware V 1.2

cube t8s
Hello my friend
I am 100% sure i have download all the files from here , my tablet is the cube t8s , 8g , quadcore , 1gb ram. I have win7 to my pc.
I follow all your steps but still nothing.

Hello garzie2000.
I have the Cube T8. I followed your guide and all went well. Rooted and partition expanded!
Thank you!
---------- Post added at 06:29 PM ---------- Previous post was at 05:57 PM ----------
By the way garzie2000, I tried to install Xposed framework (xposed-v79-sdk22-arm64.zip + XposedInstaller_3.0_alpha4.apk) but I got a bootloop and I'm now restoring my backup.
Did you installed Xposed...?
Thanks!

diboodib said:
Hello garzie2000.
I have the Cube T8. I followed your guide and all went well. Rooted and partition expanded!
Thank you!
---------- Post added at 06:29 PM ---------- Previous post was at 05:57 PM ----------
By the way garzie2000, I tried to install Xposed framework (xposed-v79-sdk22-arm64.zip + XposedInstaller_3.0_alpha4.apk) but I got a bootloop and I'm now restoring my backup.
Did you installed Xposed...?
Thanks!
Click to expand...
Click to collapse
I'm yet to try out the Xposed framework. Still quite experimental so these things are expected

jimfizz said:
Hello my friend
I am 100% sure i have download all the files from here , my tablet is the cube t8s , 8g , quadcore , 1gb ram. I have win7 to my pc.
I follow all your steps but still nothing.
Click to expand...
Click to collapse
Sorry mate. This is for the Original 16GB version of of Cube T8

hi.
if i root T8+ successfully and i want resize partition same this.
I can used "Resize_v22.4.1-signed.zip" file from this post resize partition on T8+ yes or not?

Pregressive said:
hi.
if i root T8+ successfully and i want resize partition same this.
I can used "Resize_v22.4.1-signed.zip" file from this post resize partition on T8+ yes or not?
Click to expand...
Click to collapse
It should work.

Thanks for your post. I followed yours instruction and got it sucessfully.
garzie2000 said:
Before we begin, this a guide written by a noob for noobs
What you will need;
1. A Cube T8 Phablet with an SD Card
2. A Windows PC (version 7, 8, 8.1, 10 should do)
3. Common Sense
PROCEDURE:
1. Download SuperSU from the Chainfire site and transfer to the root of the SD Card WITHOUT extraction
2. Download and Install MediaTek VCOM drivers . This Youtube Video will help you guide you through the driver installation process.
NB: Depending on your version of Windows, you may need to disable driver signature check. This guide did just that for me on my Windows 10
3. After successfully installing the driver, download the latest version of SPL Flashtool and extract that folder to somewhere like \Desktop
4. Download TWRP Recovery T8 and extract to your \Desktop as well
5. Run flash_tool (which you downloaded in Step 3). If it doesn't run, try and copy it to the root folder of your hard drive, eg. C:\SP_Flash_Tool_exe_Windows_v5.1524.00\, albo D:\SP_Flash_Tool_exe_Windows_v5.1524.00\
6. In "Download" section choose "Scatter-Loading" point to "MT6753_Android_scatter" from /TWRP Recovery folder on the desktop (downloaded in Step 4), press "Download" button.
NB: if you did everything correctly you should see that recovery pane in the dialogue box has been checked
7. Turn off the tablet. Connect it via USB to PC (tablet needs to be switched off!). After short while, flashing tool should recognize the tablet and start flashing automatically, installing TWRP recovery. After that you should get a "Successful" dialog box
8. Disconnect tablet from PC. Run it in Recovery by pressing VOLUME_UP and POWER buttons simultaneously.
9. Using VOLUME_UP button, select "Recovery" and confirm it by pressing VOLUME_DOWN button. Wait until TWRP Recovery starts.
10. In TWRP Recovery, select "Install ZIP" and point to "/external sd/UPDATE-SuperSU-v2.46.zip" (which we downloaded and placed on the root of the SD Card in Step 1)
11. After installation is finished, select "Reboot". Recovery will reboot the device.
12. After the device has rebooted successfully, you should see a new app named SuperSU in the application drawer.
Boom you have successfully rooted your device if you see the app! If you didn't see this app, you did something wrong and need to repeat the process
RESIZING OF THE PARTITION
This was the main reason why I wanted to root the T8 so badly as I was limited to only 2.9GB of internal storage.
1. Download Resize_v22.4.1-signed.zip and copy to the root of SD (without extracting)
2. Turn the device off and run Recovery by pressing VOLUME_UP and POWER button simultaneously.
3. Using VOLUME_UP button, select "Recovery" and confirm it by pressing "VOLUME_DOWN" button. Wait until TWRP Recovery starts.
4. In TWRP Recovery, select 'install ZIP' and point to "external sd/Resize_v22.4.1-signed.zip"
5. In one of following windows that pop up, select the partition size you desire. I went with 9GB and lost only the apps that I had moved manually to the SD Card.
Here's proof of my new 9GB internal storage after resizing:
Have fun!
Click to expand...
Click to collapse

Dear all,
I installed the xposed framework into the Cube T8, used the V80 and got a successful result.

Sorry I post the wrong position
Dear all,
I found a unoffical rom on CUBE OFFICAL WEBSITE, this rom inside a rom package called Cube T8 Plus FlymeOS adapt ROM(Just for Cube T8 Plus, not for T8)
, inside this package, you can find a file 合并分区线刷包, inside the file, T8-PLUS_20151224_ssd , this is the target file, unzip the file, and use computer usb to flash the rom with yours T8 plus., after flashing, finally, you will get a android 5.1 OS system, with Combined Data and SD Card partition, and A TWRP recovery, the OS not yet rooted, and also had been simplified, no google shop included, so your final job is install supersu to root it, and install Gapps zip file by recover Gapps zip file to get google shop........
Cube Tablet PC Firmware Upgrade website
http://www.51cube.com/ch/DownShow.asp?ID=392
Supersu download website
http://forum.xda-developers.com/showthread.php?t=1538053
Google Play install zip file website
http://highonandroid.com/download-android-5-1-lollipop-gapps/

Can not mount 32 GB SD card
Instructions
For insertion and mounting please?

Database Info

welcome