Database Info

Cherry mobile Omega HD (i-mobile IQ6)

Omega HD root
Disclaimer: I will not be liable for bricked devices. Follow these instructions at your own risk. ROOTING VOIDS WARRANTY, as per Cherry Mobile. Please be guided accordingly.
This tutorial is not recommended for newbies. Knowledge of basic adb and fastboot commands is helpful. Better if you have previously installed ADB drivers.
Downloads (http://www.mediafire.com/?ar2ccya8395d1):
SuperSU zip
TWRP
SP Flash Tool
MTK Drivers
MTK 6577 scatter file
if the driver didn't work download this http://www.4shared.com/zip/YXlLFoLm/6577driver_install_3_steps.html
install folder step 1 to 3
Place the scatter file and TWRP recovery in the SAME FOLDER.
rename twrp recovery to recovery.img
1. While the phone is still on, enable USB debugging (Settings > Developer options) then plug into PC. Allow drivers to install. Install the MTK drivers as well.
2. Mount phone as USB storage. Copy SuperSU zip to internal or external SD card. Unmount USB storage, then unplug phone from PC.
2. Turn off phone. Remove the battery.
3. Start SP Flash Tool. Under "Scatter-loading," choose the MT6577_Android_scatter_emmc.txt. You will see that RECOVERY has a check beside it. Click on "Download." A warning will appear, proceed anyway.
4. With your phone still off and the battery out, plug it in to the PC. Flashing should start. It will only take a few seconds. You'll see a green circle when it's done.
5. Unplug USB cable and put the battery back.
6. Enter recovery mode by Power and Volume + button. Release both buttons when you see the boot menu. Use Volume + to highlight "recovery." Then use Volume - to confirm.
7. Click "Install." Choose the appropriate tab (internal or external SD card).
8. Select UPDATE-SuperSU-1.25 zip. Swipe to confirm the update. It will flash. Go back to main menu of TWRP.
9. Click "Reboot system." Wait until you are fully booted into your homesceen.
10. Once booted, you should see SuperSU in your app drawer.
credits to ish gridote
OmegaXtremeHD
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
s3 bootanimation n sound
s3 boot logo
Jelly bean icons
iphone ringtones
google play music
dolphin browser
apex launcher
deodexed
busybox
rooted
init.d
signal tweaks
3g tweaks
battery tweaks
gpu rendering
dns tweaks
media tweaks
v6 supercharger
kickasskernel
crossbreeder
reorganized build.prop file
uploading
http://www.4shared.com/folder/dJXI2ODd/_online.html
try open first in case of corrupt file
remove crossbreeder for much better battery
flash uninstall zip http://forum.xda-developers.com/showthread.php?t=2113150
and underclock for much longer battery download setcpu or no frillcpu or anything u want i dnt care..
save rom in SD card
reboot to CWM/TWRP
install rom via SD card
reboot
I'm not responsible for any loss of data or brick....
i think this only works on iq6A

do you already own this phone?

Cherry mobile Omega HD info states that its a dual core phone while all info about i-mobile IQ6 states its a single core phone. does anyone know which mediatek chipset the Omega HD uses? It's GPU?

yes i had it

How?
How can we flash the CWM to the Omega HD if you don't even give us a flashtool? Is this Rooting process tested? is it working?

Please help me
Wil53664 said:
yes i had it
Click to expand...
Click to collapse
Sir, can I have a copy of the Setting.apk of your Cherry Mobile HD? i've accidentally forgot to have a backup of it and now, i've accidentally just erased it. please help me. thankyou very much

Pretty Please?
Wil53664 said:
yes i had it
Click to expand...
Click to collapse
please post the Settings.apk of the Cherry Mobile Omega HD sir. I really need it it would be appreciated if you post it here.

How to Backup the phone
just bought the phone yesterday
do yo guys know how to back up this jellybean phone?

Hey guys, if you have FB we have a group with most of oHD users. Just search "CherryMobileOmegaHD" in FB (can't post links yet. sorry)
There are custom roms in the group, the usual rom cooked from dsdixda's kitchen (zipalign, deodexed, rm bloatwares)
@cyzarine
What do you mean with backup? We have the stock rom in the group, you might want to check it out.

Bummer! I'm stuck at step 3!
You will see that RECOVERY has a check beside it. Click on "Download." A warning will appear, proceed anyway.
Click to expand...
Click to collapse
-- umm... NO, I DON'T!! There must be a step that's missing... :-S
edit:
nevermind. I forgot to rename TWRP file to "recovery"
Thanks for this!

anyone have a kernel that have oc"?

In need...
Woke up to a drained Omega HD today.
Plugged it in to have it charged.
Switched it on afterwards.
"OmegaHD" flashed before my eyes, followed by a blank screen with the familiar Cherry Mobile tune playing on the background. And then nothing! NO DISPLAY! I touch the screen and there are sounds playing to confirm each press, which means I am pressing on the right places -- only that there is NO DISPLAY APPEARING.
I switch it on and off, still the same results.
Wiped cache. Nothing... Since it's practically new, I go ahead and factory-restore the thing... still the same results. NO DISPLAY! :-S
What else can I do to this device to have it work properly?!

Have you installed any custom rom or any other zip files with your phone?

xMinistro said:
Have you installed any custom rom or any other zip files with your phone?
Click to expand...
Click to collapse
do have stock rom can you give plsss......

---------- Post added at 11:02 PM ---------- Previous post was at 10:41 PM ----------
[/COLOR]
Wil53664 said:
Omega HD root
Disclaimer: I will not be liable for bricked devices. Follow these instructions at your own risk. ROOTING VOIDS WARRANTY, as per Cherry Mobile. Please be guided accordingly.
This tutorial is not recommended for newbies. Knowledge of basic adb and fastboot commands is helpful. Better if you have previously installed ADB drivers.
Downloads (http://www.mediafire.com/?ar2ccya8395d1):
SuperSU zip
TWRP ported by me
SP Flash Tool
MTK Drivers
MTK 6577 scatter file
if the driver didn't work download this http://www.4shared.com/zip/YXlLFoLm/6577driver_install_3_steps.html
install folder step 1 to 3
Place the scatter file and TWRP recovery in the SAME FOLDER.
rename twrp recovery to recovery.img
1. While the phone is still on, enable USB debugging (Settings > Developer options) then plug into PC. Allow drivers to install. Install the MTK drivers as well.
2. Mount phone as USB storage. Copy SuperSU zip to internal or external SD card. Unmount USB storage, then unplug phone from PC.
2. Turn off phone. Remove the battery.
3. Start SP Flash Tool. Under "Scatter-loading," choose the MT6577_Android_scatter_emmc.txt. You will see that RECOVERY has a check beside it. Click on "Download." A warning will appear, proceed anyway.
4. With your phone still off and the battery out, plug it in to the PC. Flashing should start. It will only take a few seconds. You'll see a green circle when it's done.
5. Unplug USB cable and put the battery back.
6. Enter recovery mode by Power and Volume + button. Release both buttons when you see the boot menu. Use Volume + to highlight "recovery." Then use Volume - to confirm.
7. Click "Install." Choose the appropriate tab (internal or external SD card).
8. Select UPDATE-SuperSU-1.25 zip. Swipe to confirm the update. It will flash. Go back to main menu of TWRP.
9. Click "Reboot system." Wait until you are fully booted into your homesceen.
10. Once booted, you should see SuperSU in your app drawer.
credits to ish gridote
Click to expand...
Click to collapse
Hi. Can you please post a mirror on the twrp-omegahd.img file? All of the other files have been downloaded except for the img file. Error comes up.

bakes5981 said:
Bummer! I'm stuck at step 3!
-- umm... NO, I DON'T!! There must be a step that's missing... :-S
edit:
nevermind. I forgot to rename TWRP file to "recovery"
Thanks for this!
Click to expand...
Click to collapse
please hit thanks if this helps

OmegaXtremeHD link issues
OmegaXtremeHD link is not working .... 509 error .... any mirror or alternative links?

Wil53664 said:
Omega HD root
Disclaimer: I will not be liable for bricked devices. Follow these instructions at your own risk. ROOTING VOIDS WARRANTY, as per Cherry Mobile. Please be guided accordingly.
This tutorial is not recommended for newbies. Knowledge of basic adb and fastboot commands is helpful. Better if you have previously installed ADB drivers.
Downloads (http://www.mediafire.com/?ar2ccya8395d1):
SuperSU zip
TWRP ported by me
SP Flash Tool
MTK Drivers
MTK 6577 scatter file
if the driver didn't work download this http://www.4shared.com/zip/YXlLFoLm/6577driver_install_3_steps.html
install folder step 1 to 3
Place the scatter file and TWRP recovery in the SAME FOLDER.
rename twrp recovery to recovery.img
1. While the phone is still on, enable USB debugging (Settings > Developer options) then plug into PC. Allow drivers to install. Install the MTK drivers as well.
2. Mount phone as USB storage. Copy SuperSU zip to internal or external SD card. Unmount USB storage, then unplug phone from PC.
2. Turn off phone. Remove the battery.
3. Start SP Flash Tool. Under "Scatter-loading," choose the MT6577_Android_scatter_emmc.txt. You will see that RECOVERY has a check beside it. Click on "Download." A warning will appear, proceed anyway.
4. With your phone still off and the battery out, plug it in to the PC. Flashing should start. It will only take a few seconds. You'll see a green circle when it's done.
5. Unplug USB cable and put the battery back.
6. Enter recovery mode by Power and Volume + button. Release both buttons when you see the boot menu. Use Volume + to highlight "recovery." Then use Volume - to confirm.
7. Click "Install." Choose the appropriate tab (internal or external SD card).
8. Select UPDATE-SuperSU-1.25 zip. Swipe to confirm the update. It will flash. Go back to main menu of TWRP.
9. Click "Reboot system." Wait until you are fully booted into your homesceen.
10. Once booted, you should see SuperSU in your app drawer.
credits to ish gridote
OmegaXtremeHD
s3 bootanimation n sound
s3 boot logo
Jelly bean icons
iphone ringtones
google play music
dolphin browser
apex launcher
deodexed
busybox
init.d
signal tweaks
3g tweaks
battery tweaks
v6 supercharger
kickasskernel
crossbreeder
download link
https://www.dropbox.com/s/8q1c6db45uegepk/OmegaXtreme.zip
updated link
save rom in SD card
reboot to CWM/TWRP
WIPE DATA/FACTORY RESET
install rom via SD card
reboot
Click to expand...
Click to collapse
Hey buddy,
Where's the file..??

StanleyD said:
Hey buddy,
Where's the file..??
Click to expand...
Click to collapse
will update link later

having trouble with some apps working on my Omega HD. a couple of my Android mainstays are Haxsync and Swiftkey. on my Omega HD, they run no problem, but if the unit powers off for whatever reason, when I turn it back on, my Haxsync account (under Settings/Accounts) disappears, requiring me to set up the app again, and Swiftkey is no longer activated as my default input. any help?

CUBOT S200 root guide

CUBOT S200 root guide
Introduction
After a couple of months of searching for information, failing to get correct instructions from the seller and trying all available and often shady one-click root programs, I have finally successfully rooted my CUBOT S200 device.
In fact, all thanks go to rfax from this spanish forum:
http://www.movilesdualsim.com/tema/cubot-s200-root-y-recovery.93358/
The point of my post is to provide the same information in english and here, on the most widely read forum, xda-developers.com.
Before giving any instructions, I feel like I have to caution anyone trying this that I can accept no responsability for anything happening to your smartphone, as a result of following this guide. You are on your own and neither me nor anyone else is responsible for any damage, job loss, broken relationship, death or mass destruction
Also, make sure you BACKUP whatever you don't want to lose!
This rooting process should not result in any data loss, but it's always a good idea to BACKUP your stuff. So, if you have data on your phone for which you have no BACKUP, this is just a good opportunity to BACK IT UP.
Although it may seem obvious to some, please read the ENTIRE guide, BEFORE actually doing anything. This will allow you to have a general idea of the procedure and plan your steps.
Preparation
The hardware you are going to need is:
CUBOT S200 android smartphone (duh)
Windows PC
USB-microUSB data cable
My desktop machine is on linux, so in order to root my CUBOT S200, I used a Windows 7 netbook. I am pretty sure any Windows PC should do, but you definitely need a Windows machine for these instructions.
I have not even looked into the existence of an equivalent tool for linux or mac. If anyone has any information, please share and I would be glad to update the guide accordingly.
Here is a list of the software I used:
SP Flash Tools v5.1408.00
download here [RAR]
SuperSU
download here
You can find information about the latest version here
Recovery
download here
Drivers
download here
You should unzip/unrar all files, except for the SuperSU. Just keep the SuperSU zip file. It should be copied to the phone, either the internal memory or the external SD, if available. Just to be sure, I would recommend that you copy it to both locations. You can always delete it after you are done rooting the S200.
Inside the drivers zip file there is a folder and another folder inside it with a ...3rd folder in it and two executables, install & uninstall. The install is the one you will be using.
If you already have the required drivers installed, you can ignore these. If SP Flash Tool cannot proceed with the "download" as it calls it, then you need the drivers. More on that in the steps below.
Instructions
Overview
You will flash the Clockworkmod (CWM) recovery image to your phone using the SP Flash Tool.
You will then boot your phone into recovery and install the SuperSU program from the zip file.
That's it, just reboot and you have a rooted CUBOT S200!
Remember to BACKUP any data you have not already BACKED UP, or carelessly ignore this message, root your phone without any problems and then a few days or weeks later lose stuff for any unrelated reason and bang your head against a wall for not having seized this opportunity to BACKUP your sh*t.
Here goes:
Step 1
1. Make sure you have the SuperSU zip file. DO NOT UNZIP. If you downloaded from the link provided, the file should be named UPDATE-SuperSU-v2.46.zip
2. Copy this file to you S200. If you have a SD card, copy to both the SD card and the internal memory, so you can definitely find it in the recovery.
Step 2
1. Power off your phone
2. Remove the battery
Step 3
Make sure you have unzipped the Recovery. There should be a folder named "Recovery CWM" inside, including 2 files: MT6582_Android_scatter.txt and recovery.img
Step 4
1. Make sure you have downloaded and unrared the SP Flash Tool. You should have a folder named SP_Flash_Tool_v5.1408.00
2. Run the tool, it should be a file named flash_tool.exe
3. Click on the button Scatter-loading
4. Find the folder Recovery CWM from step 3 and choose the file MT6582_Android_scatter.txt. Make sure only RECOVERY is checked.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5. Click Download. The Download button should be grayed out and Stop should be green or active anyway
Ok, let's make a new step for clarity.
Step 5
6. Put the battery in your phone. DO NOT TURN ON your phone
7. Connect your phone to the PC with the USB cable. DO NOT TURN ON your phone
8. A red full progress bar should appear at the bottom of the SP Flash Tool window, then a yellow bar should fill up (pretty quickly). When the yellow bar reaches 100%, a small window will pop up saying Download Ok!
9. Close the popup window. Close the SP Flash Tool. Disconnect your phone. You now have CWM recovery on your S200
Step 6
1. Press and hold down your phone's Volume Up button. DO NOT LET GO
2. Without letting go the vol+, press and hold down the Power button. Hold BOTH buttons down
3. The white CUBOT startup screen will appear and a few seconds later the phone will enter the CWM recovery mode. Now you can let go both buttons
(not the exact things you will see, just for illustration)
4. Using the Vol+/- buttons, choose Install zip from sdcard. Click the power button
5. Then Choose zip from sdcard
6. Find the SuperSU zip that you copied to your phone in step 1 and confirm with the power button
7. Choose Yes - Install
8. Once SuperSU is successfully installed, you will be back at the first screen. Choose Reboot system now
Step 7
Not really a step. Your phone should reboot (don't hold down any buttons) and you should now have root access!
Enjoy!
Unlimited thanks to rfax from the spanish site, where I found the instructions, http://www.movilesdualsim.com/tema/cubot-s200-root-y-recovery.93358/.
I am not an expert on these matters, but feel free to ask anything and I am sure someone, maybe even me, will step up and help you.
If you find any typos, mistakes, errors or have any remarks, which would make this guide better, please let me know and I will do my best to keep this post current and helpful.
Cheers,
panda2005
No kittens were harmed during the production of this guide.

Cant go into recovery Mode
panda2005 said:
CUBOT S200 root guide
Introduction
After a couple of months of searching for information, failing to get correct instructions from the seller and trying all available and often shady one-click root programs, I have finally successfully rooted my CUBOT S200 device.
In fact, all thanks go to rfax from this spanish forum:
http://www.movilesdualsim.com/tema/cubot-s200-root-y-recovery.93358/
The point of my post is to provide the same information in english and here, on the most wide read forum, xda-developers.com.
Before giving any instructions, I feel like I have to caution anyone trying this that I can accept no responsability for anything happening to your smartphone, as a result of following guide. You are on your own and neither me nor anyone else is responsible for any damage, job loss, broken relationship, death or mass destruction
Also, make sure you BACKUP whatever you don't want to lose!
This rooting process should not result in any data loss, but it's always a good idea to BACKUP your stuff. So, if you have data on your phone for which you have no BACKUP, this is just a good opportunity to BACK IT UP.
Although it may seem obvious to some, please read the ENTIRE guide, BEFORE actually doing anything. This will allow you to have a general idea of the procedure and plan your steps.
Preparation
The hardware you are going to need is:
CUBOT S200 android smartphone (duh)
Windows PC
USB-microUSB data cable
My desktop machine is on linux, so in order to root my CUBOT S200, I used a Windows 7 netbook. I am pretty sure any Windows PC should do, but you definitely need a Windows machine for these instructions.
I have not even looked into the existence of an equivalent tool for linux or mac. If anyone has any information, please share and I would be glad to update the guide accordingly.
Here is a list of the software I used:
SP Flash Tools v5.1408.00
download here [RAR]
SuperSU
download here
You can find information about the latest version here
Recovery
download here
Drivers
download here
You should unzip/unrar all files, except for the SuperSU. Just keep the SuperSU zip file. It should be copied to the phone, either the internal memory or the external SD, if available. Just to be sure, I would recommend that you copy it to both locations. You can always delete it after you are done rooting the S200.
Inside the drivers zip file there is a folder and another folder inside it with a ...3rd folder in it and two executables, install & uninstall. The install is the one you will be using.
If you already have the required drivers installed, you can ignore these. If SP Flash Tool cannot proceed with the "download" as it calls it, then you need the drivers. More on that in the steps below.
Instructions
Overview
You will flash the Clockworkmod (CWM) recovery image to your phone using the SP Flash Tool.
You will then boot your phone into recovery and install the SuperSU program from the zip file.
That's it, just reboot and you have a rooted CUBOT S200!
Remember to BACKUP any data you have not already BACKED UP, or carelessly ignore this message, root your phone without any problems and then a few days or weeks later lose stuff for any unrelated reason and bang your head against a wall for not having seized this opportunity to BACKUP your sh*t.
Here goes:
Step 1
1. Make sure you have the SuperSU zip file. DO NOT UNZIP. If you downloaded from the link provided, the file should be named UPDATE-SuperSU-v2.46.zip
2. Copy this file to you S200. If you have a SD card, copy to both the SD card and the internal memory, so you can definitely find it in the recovery.
Step 2
1. Power off your phone
2. Remove the battery
Step 3
Make sure you have unzipped the Recovery. There should be a folder named "Recovery CWM" inside, including 2 files: MT6582_Android_scatter.txt and recovery.img
Step 4
1. Make sure you have downloaded and unrared the SP Flash Tool. You should have a folder named SP_Flash_Tool_v5.1408.00
2. Run the tool, it should be a file named flash_tool.exe
3. Click on the button Scatter-loading
4. Find the folder Recovery CWM from step 3 and choose the file MT6582_Android_scatter.txt. Make sure only RECOVERY is checked.
5. Click Download. The Download button should be grayed out and Stop should be green or active anyway
Ok, let's make a new step for clarity.
Step 5
6. Put the battery in your phone. DO NOT TURN ON your phone
7. Connect your phone to the PC with the USB cable. DO NOT TURN ON your phone
8. A red full progress bar should appear at the bottom of the SP Flash Tool window, then a yellow bar should fill up (pretty quickly). When the yellow bar reaches 100%, a small window will pop up saying Download Ok!
9. Close the popup window. Close the SP Flash Tool. Disconnect your phone. You now have CWM recovery on your S200
Step 6
1. Press and hold down your phone's Volume Up button. DO NOT LET GO
2. Without letting go the vol+, press and hold down the Power button. Hold BOTH buttons down
3. The white CUBOT startup screen will appear and a few seconds later the phone will enter the CWM recovery mode. Now you can let go both buttons
(not the exact things you will see, just for illustration)
4. Using the Vol+/- buttons, choose Install zip from sdcard. Click the power button
5. Then Choose zip from sdcard
6. Find the SuperSU zip that you copied to your phone in step 1 and confirm with the power button
7. Choose Yes - Install
8. Once SuperSU is successfully installed, you will be back at the first screen. Choose Reboot system now
Step 7
Not really a step. Your phone should reboot (don't hold down any buttons) and you should now have root access!
Enjoy!
Unlimited thanks to rfax from the spanish site, where I found the instructions, http://www.movilesdualsim.com/tema/cubot-s200-root-y-recovery.93358/.
I am not an expert on these matters, but feel free to ask anything and I am sure someone, maybe even me, will step up and help you.
If you find any typos, mistakes, errors or have any remarks, which would make this guide better, please let me know and I will do my best to keep this post current and helpful.
Cheers,
panda2005
No kittens were harmed during the production of this guide.
Click to expand...
Click to collapse
Hi I did all the steps and when i try to access recovery menu (Vol+ plus power button) it wont allow me to do so. It goes into a loop and just flashing the Cubot logo,
Please help me.

sopedyoi said:
Hi I did all the steps and when i try to access recovery menu (Vol+ plus power button) it wont allow me to do so. It goes into a loop and just flashing the Cubot logo,
Please help me.
Click to expand...
Click to collapse
In the Recovery zip you downloaded (see link in guide), there is also a folder Recovery Original.
In there you can find another scatter file, also named MT6582_Android_scatter.txt.
Flash this one and you should get the original recovery back.
Please, make sure you follow all the steps very carefully. Again, I know that people have followed this guide with success in the spanish site and I have done so too.
Hope that helps!

Thank you for sharing.

Working now!
panda2005 said:
In the Recovery zip you downloaded (see link in guide), there is also a folder Recovery Original.
In there you can find another scatter file, also named MT6582_Android_scatter.txt.
Flash this one and you should get the original recovery back.
Please, make sure you follow all the steps very carefully. Again, I know that people have followed this guide with success in the spanish site and I have done so too.
Hope that helps!
Click to expand...
Click to collapse
Thank you for the help!
Looks like is rooted now.
Now i have another question. i saw a post about converting 2G phones to 3G phones via fastboot. refer to link: http://forum.xda-developers.com/one...11s-modem-problem-t2824139/page5#post54753177
I will like to know if this is possible with this phone since i need the 1900 3G band on this phone.
Please let me know.

sopedyoi said:
Thank you for the help!
Looks like is rooted now.
Now i have another question. i saw a post about converting 2G phones to 3G phones via fastboot. refer to link: http://forum.xda-developers.com/one...11s-modem-problem-t2824139/page5#post54753177
I will like to know if this is possible with this phone since i need the 1900 3G band on this phone.
Please let me know.
Click to expand...
Click to collapse
I don't really know anything about that. Hopefully, someone will see this and come up with a solution, if it is indeed possible.
Congrats on rooting your phone, enjoy!

"A red full progress bar should appear at the bottom of the SP Flash Tool window, then a yellow bar should fill up (pretty quickly). When the yellow bar reaches 100%, a small window will pop up saying Download Ok!"
No bar appears for me....

mchart03 said:
"A red full progress bar should appear at the bottom of the SP Flash Tool window, then a yellow bar should fill up (pretty quickly). When the yellow bar reaches 100%, a small window will pop up saying Download Ok!"
No bar appears for me....
Click to expand...
Click to collapse
Maybe the drivers are not successfully installed. Try rebooting your computer and/or installing the drivers again.

Windows 10 drivers
First of all, thanks gor the great guide! I am now rooted.:good:
I did run into a problem with the drivers though. They don't work with Windows10. After looking around a bit I found a great guide with drivers that did work.
Here's the link.
(Sorry but I can't post outside links. You'll have to copy and paste to your browser.)
laurentiumihet.ro/technology/windows-10-mtk-vcom-usb-drivers-for-32-64-bit-drivers-installation-tutorial/
Enjoy!

Trouble with red full progress bar
Hi
I put the battery in my phone. My phone is off
I connect my phone to the PC with the USB cable.
But nothing red full progress bar appear at the bottom of the SP Flash Tool window
Can you explain to me why this happens?
Thank's
Ardi

Custom ROM for Cubot S200
Hi Panda2005.
Thanks for excellent post on rooting the S200.
I have tried several rooting tools and they all failed for one reason or another and your method worked first time.
I am new to Android and find it a little confusing compared with Windows but I am learning!
My question is can you recommend a custom ROM suitable for the S200?
Thanks again.

nailbender7 said:
Hi Panda2005.
Thanks for excellent post on rooting the S200.
I have tried several rooting tools and they all failed for one reason or another and your method worked first time.
I am new to Android and find it a little confusing compared with Windows but I am learning!
My question is can you recommend a custom ROM suitable for the S200?
Thanks again.
Click to expand...
Click to collapse
I am glad you managed to root your phone.
Actually, I have never tried any custom ROMs, so unfortunately I could not recommend any.
I have since bought a new phone, so I have not played with the S200 in over a year. A friend of mine has borrowed it, but he has not looked for custom ROMs either.
If you find/try any cool ones, feel free to let me know here.
Good luck!

Re Cubot s200
Hi Panda 2005,
Yes I too have come to the conclusion that the S200 does not have a big enough following in order to warrant much interest from the techies capable of creating such ROMs.
As a matter of interest can you recommend a phone with plenty of ROMs available for experimentation?
I have been looking at a second hand Samsung S4. Not too expensive if I brick it!

Sorry, I have not dabbled with custom ROMs in a few years, not since I had a ZTE Skate Acqua. Good times!

[Guide] How to Root Original Cube T8 and Resize partition

Before we begin, this a guide written by a noob for noobs
Disclaimer; I'm not responsible if you fry your device. Just follow this guide assiduously and you should be fine
Click to expand...
Click to collapse
What you will need;
1. A Cube T8 Phablet with an SD Card
2. A Windows PC (version 7, 8, 8.1, 10 should do)
3. Common Sense
PROCEDURE:
1. Download SuperSU from the Chainfire site and transfer to the root of the SD Card WITHOUT extraction
2. Download and Install MediaTek VCOM drivers . This Youtube Video will help you guide you through the driver installation process.
NB: Depending on your version of Windows, you may need to disable driver signature check. This guide did just that for me on my Windows 10
3. After successfully installing the driver, download the latest version of SPL Flashtool and extract that folder to somewhere like \Desktop
4. Download TWRP Recovery T8 and extract to your \Desktop as well
5. Run flash_tool (which you downloaded in Step 3). If it doesn't run, try and copy it to the root folder of your hard drive, eg. C:\SP_Flash_Tool_exe_Windows_v5.1524.00\, albo D:\SP_Flash_Tool_exe_Windows_v5.1524.00\
6. In "Download" section choose "Scatter-Loading" point to "MT6753_Android_scatter" from /TWRP Recovery folder on the desktop (downloaded in Step 4), press "Download" button.
NB: if you did everything correctly you should see that recovery pane in the dialogue box has been checked
7. Turn off the tablet. Connect it via USB to PC (tablet needs to be switched off!). After short while, flashing tool should recognize the tablet and start flashing automatically, installing TWRP recovery. After that you should get a "Successful" dialog box
8. Disconnect tablet from PC. Run it in Recovery by pressing VOLUME_UP and POWER buttons simultaneously.
9. Using VOLUME_UP button, select "Recovery" and confirm it by pressing VOLUME_DOWN button. Wait until TWRP Recovery starts.
10. In TWRP Recovery, select "Install ZIP" and point to "/external sd/UPDATE-SuperSU-v2.46.zip" (which we downloaded and placed on the root of the SD Card in Step 1)
11. After installation is finished, select "Reboot". Recovery will reboot the device.
12. After the device has rebooted successfully, you should see a new app named SuperSU in the application drawer.
Boom you have successfully rooted your device if you see the app! If you didn't see this app, you did something wrong and need to repeat the process
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
RESIZING OF THE PARTITION
This was the main reason why I wanted to root the T8 so badly as I was limited to only 2.9GB of internal storage.
1. Download Resize_v22.4.1-signed.zip and copy to the root of SD (without extracting)
2. Turn the device off and run Recovery by pressing VOLUME_UP and POWER button simultaneously.
3. Using VOLUME_UP button, select "Recovery" and confirm it by pressing "VOLUME_DOWN" button. Wait until TWRP Recovery starts.
4. In TWRP Recovery, select 'install ZIP' and point to "external sd/Resize_v22.4.1-signed.zip"
5. In one of following windows that pop up, select the partition size you desire. I went with 9GB and lost only the apps that I had moved manually to the SD Card.
Here's proof of my new 9GB internal storage after resizing:
Have fun!

Really interesting Thank you for this Information!

Krystyna said:
Really interesting Thank you for this Information!
Click to expand...
Click to collapse
You are welcome!

Can you tell if this would work on New Cube T8 Plus Ultimate?
Thanks un advance
Enviado desde mi bq Elcano mediante Tapatalk

Please anyone knows if this would work on T8 plus?
Enviado desde mi bq Elcano mediante Tapatalk

Hello , I follow all the steps and when i am to step 6 and press download , nothing is downloading , i put tablet to usb and message me installation wrong.

bolija said:
Please anyone knows if this would work on T8 plus?
Enviado desde mi bq Elcano mediante Tapatalk
Click to expand...
Click to collapse
Use this tutorial for the T8 Plus;
http://forum.xda-developers.com/android/general/guide-how-to-root-cube-t8-plus-t3256490

jimfizz said:
Hello , I follow all the steps and when i am to step 6 and press download , nothing is downloading , i put tablet to usb and message me installation wrong.
Click to expand...
Click to collapse
it doesn't really download anything per se. It just downloads to the tablet after you turn it off and connect to the PC

Still something wrong
garzie2000 said:
it doesn't really download anything per se. It just downloads to the tablet after you turn it off and connect to the PC
Click to expand...
Click to collapse
Thank you for your response but still something wrond and i can not complete root.
In step 6 In "Download" section choose "Scatter-Loading" point to "MT6753_Android_scatter" mine scatter loading had MT6735M. I press downloading and continue step 7.
Flashtool start work and get a message box " PMT changed for the ROM; it must be downloaded. I press OK and nothing happened
In step 8 - 9 After choose recovery i went to a menu and there is not any choice install zip. I press reboot and back again here. What i make wrong my friend?
Regards,Dimitris

jimfizz said:
Thank you for your response but still something wrond and i can not complete root.
In step 6 In "Download" section choose "Scatter-Loading" point to "MT6753_Android_scatter" mine scatter loading had MT6735M. I press downloading and continue step 7.
Flashtool start work and get a message box " PMT changed for the ROM; it must be downloaded. I press OK and nothing happened
In step 8 - 9 After choose recovery i went to a menu and there is not any choice install zip. I press reboot and back again here. What i make wrong my friend?
Regards,Dimitris
Click to expand...
Click to collapse
That's weird please make sure that you download the files from this thread and not google and that you have the Original Cube T8 running the latest firmware V 1.2

cube t8s
Hello my friend
I am 100% sure i have download all the files from here , my tablet is the cube t8s , 8g , quadcore , 1gb ram. I have win7 to my pc.
I follow all your steps but still nothing.

Hello garzie2000.
I have the Cube T8. I followed your guide and all went well. Rooted and partition expanded!
Thank you!
---------- Post added at 06:29 PM ---------- Previous post was at 05:57 PM ----------
By the way garzie2000, I tried to install Xposed framework (xposed-v79-sdk22-arm64.zip + XposedInstaller_3.0_alpha4.apk) but I got a bootloop and I'm now restoring my backup.
Did you installed Xposed...?
Thanks!

diboodib said:
Hello garzie2000.
I have the Cube T8. I followed your guide and all went well. Rooted and partition expanded!
Thank you!
---------- Post added at 06:29 PM ---------- Previous post was at 05:57 PM ----------
By the way garzie2000, I tried to install Xposed framework (xposed-v79-sdk22-arm64.zip + XposedInstaller_3.0_alpha4.apk) but I got a bootloop and I'm now restoring my backup.
Did you installed Xposed...?
Thanks!
Click to expand...
Click to collapse
I'm yet to try out the Xposed framework. Still quite experimental so these things are expected

jimfizz said:
Hello my friend
I am 100% sure i have download all the files from here , my tablet is the cube t8s , 8g , quadcore , 1gb ram. I have win7 to my pc.
I follow all your steps but still nothing.
Click to expand...
Click to collapse
Sorry mate. This is for the Original 16GB version of of Cube T8

hi.
if i root T8+ successfully and i want resize partition same this.
I can used "Resize_v22.4.1-signed.zip" file from this post resize partition on T8+ yes or not?

Pregressive said:
hi.
if i root T8+ successfully and i want resize partition same this.
I can used "Resize_v22.4.1-signed.zip" file from this post resize partition on T8+ yes or not?
Click to expand...
Click to collapse
It should work.

Thanks for your post. I followed yours instruction and got it sucessfully.
garzie2000 said:
Before we begin, this a guide written by a noob for noobs
What you will need;
1. A Cube T8 Phablet with an SD Card
2. A Windows PC (version 7, 8, 8.1, 10 should do)
3. Common Sense
PROCEDURE:
1. Download SuperSU from the Chainfire site and transfer to the root of the SD Card WITHOUT extraction
2. Download and Install MediaTek VCOM drivers . This Youtube Video will help you guide you through the driver installation process.
NB: Depending on your version of Windows, you may need to disable driver signature check. This guide did just that for me on my Windows 10
3. After successfully installing the driver, download the latest version of SPL Flashtool and extract that folder to somewhere like \Desktop
4. Download TWRP Recovery T8 and extract to your \Desktop as well
5. Run flash_tool (which you downloaded in Step 3). If it doesn't run, try and copy it to the root folder of your hard drive, eg. C:\SP_Flash_Tool_exe_Windows_v5.1524.00\, albo D:\SP_Flash_Tool_exe_Windows_v5.1524.00\
6. In "Download" section choose "Scatter-Loading" point to "MT6753_Android_scatter" from /TWRP Recovery folder on the desktop (downloaded in Step 4), press "Download" button.
NB: if you did everything correctly you should see that recovery pane in the dialogue box has been checked
7. Turn off the tablet. Connect it via USB to PC (tablet needs to be switched off!). After short while, flashing tool should recognize the tablet and start flashing automatically, installing TWRP recovery. After that you should get a "Successful" dialog box
8. Disconnect tablet from PC. Run it in Recovery by pressing VOLUME_UP and POWER buttons simultaneously.
9. Using VOLUME_UP button, select "Recovery" and confirm it by pressing VOLUME_DOWN button. Wait until TWRP Recovery starts.
10. In TWRP Recovery, select "Install ZIP" and point to "/external sd/UPDATE-SuperSU-v2.46.zip" (which we downloaded and placed on the root of the SD Card in Step 1)
11. After installation is finished, select "Reboot". Recovery will reboot the device.
12. After the device has rebooted successfully, you should see a new app named SuperSU in the application drawer.
Boom you have successfully rooted your device if you see the app! If you didn't see this app, you did something wrong and need to repeat the process
RESIZING OF THE PARTITION
This was the main reason why I wanted to root the T8 so badly as I was limited to only 2.9GB of internal storage.
1. Download Resize_v22.4.1-signed.zip and copy to the root of SD (without extracting)
2. Turn the device off and run Recovery by pressing VOLUME_UP and POWER button simultaneously.
3. Using VOLUME_UP button, select "Recovery" and confirm it by pressing "VOLUME_DOWN" button. Wait until TWRP Recovery starts.
4. In TWRP Recovery, select 'install ZIP' and point to "external sd/Resize_v22.4.1-signed.zip"
5. In one of following windows that pop up, select the partition size you desire. I went with 9GB and lost only the apps that I had moved manually to the SD Card.
Here's proof of my new 9GB internal storage after resizing:
Have fun!
Click to expand...
Click to collapse

Dear all,
I installed the xposed framework into the Cube T8, used the V80 and got a successful result.

Sorry I post the wrong position
Dear all,
I found a unoffical rom on CUBE OFFICAL WEBSITE, this rom inside a rom package called Cube T8 Plus FlymeOS adapt ROM(Just for Cube T8 Plus, not for T8)
, inside this package, you can find a file 合并分区线刷包, inside the file, T8-PLUS_20151224_ssd , this is the target file, unzip the file, and use computer usb to flash the rom with yours T8 plus., after flashing, finally, you will get a android 5.1 OS system, with Combined Data and SD Card partition, and A TWRP recovery, the OS not yet rooted, and also had been simplified, no google shop included, so your final job is install supersu to root it, and install Gapps zip file by recover Gapps zip file to get google shop........
Cube Tablet PC Firmware Upgrade website
http://www.51cube.com/ch/DownShow.asp?ID=392
Supersu download website
http://forum.xda-developers.com/showthread.php?t=1538053
Google Play install zip file website
http://highonandroid.com/download-android-5-1-lollipop-gapps/

Can not mount 32 GB SD card
Instructions
For insertion and mounting please?

[HOWTO] Unlock and root the Galaxy Tab S6 Lite

Hey guys,
I know its the same with the other tablets but i wanna make one just cause its easier for people.
How to unlock::
1. Turn on your device and then go to settings --> scroll down to about tablet --> Software Information then tap the Build number 7 or 8 times or until it says you unlocked developer options.
2. Go to developer options and tick OEM UNLOCK and then a warning will pop up and just accept it.
3. Turn off your device, then while holding both volume up and down, connect your device to the pc.
4. A New screen should appear saying stuff about custom roms and stuff, Jut hold and press the up button until it resets. ( THis will erase everything on the tablet)
5. if you're like me and set up the tablet and went straightfoward to unlocking the bootloader, follow this guide: https://forum.xda-developers.com/galaxy-s8/how-to/how-to-bypass-rmm-prenormal-to-install-t3891193
So you wont have any issues flashing roms a nd stuff and dont have to wait 7 days.
6. Now your bootloader should be unlocked! (To enter download/odin mode: Do the same thing, Turn off the device and hold both volume buttons while connecting to the pc then instead of long pressing up, just press up once.)
How to root:
1. Download the firmware for your your tablet, i dont know if i can link the sites but you can google it.
2. Extract only the AP portion of the firmware.
3. Open up the AP portion with 7-zip or winrar
4. extract the boot.img.lz4 out of the AP file
5. Download Lz4 https://github.com/lz4/lz4/releases to your pc corresponding version.
6. Extract the LZ4 to the same area where the boot.img.lz4 is
7. Open command prompt in that folder and then do
Code:
lz4 boot.img.lz4 boot.img
8. Move the boot.img to your tablet, open up magisk manager then clicked Advanced Settings or Advanced, then untick Perserve AVB 2.0/Dm-verity and FIle Encryption then patch it.
9. Take the patched_magisk out of the tablet to your pc and then rename it from magisk_patched.img to boot.img
10. Use 7-zip or winrar and right click on the boot.img and add to archive
11. Select Tar (This is 7-zip havent tried winrar)
12. Once its complete use odin to flash that boot.tar on the AP Section
13. You should now be rooted
Thanks to
@Iceman66
@b0bness

Iceman66 had posted a link in some thread about firmware sources
Thread link: https://forum.xda-developers.com/showpost.php?p=82969923&postcount=9
Firmware source: https://samfrew.com/model/SM-P610/

HI! Tnx!
Is it work without twrp?
Can I use samsung upgrade fot tab s6 lite after root it or not?
If not where to find a new rom, safety updates?
Thanks again!

Can someone write more detailed description step by step without abbreviations please?

Rupdabe-GalaxyS6EdgePlus said:
Can someone write more detailed description step by step without abbreviations please?
Click to expand...
Click to collapse
If you don’t know what you are doing, I suggest not rooting your device

Hi I'm familiar with magisk and oneplus, motorola, htc etc but not with Samsung. How can I still upgrade my device without losing root?
My tab S6 lite, notifies me about an upgrade but it looks like it hasn't got an a and B psystem partition so you can love update en before reboot just use magisk to patch the bootloader and keep root. Any suggestions?

Awesomeslayerg said:
If you don’t know what you are doing, I suggest not rooting your device
Click to expand...
Click to collapse
I know but description is too shoot.
---------- Post added at 09:31 PM ---------- Previous post was at 08:46 PM ----------
9. Take the patched_magisk out of the tablet to your pc and then rename it from magisk_patched.img to boot.img
Where can I take it? patched_magisk

Rupdabe-GalaxyS6EdgePlus said:
I know but description is too shoot.
---------- Post added at 09:31 PM ---------- Previous post was at 08:46 PM ----------
9. Take the patched_magisk out of the tablet to your pc and then rename it from magisk_patched.img to boot.img
Where can I take it? patched_magisk
Click to expand...
Click to collapse
It's in the Download folder.

Awesomeslayerg said:
It's in the Download folder.
Click to expand...
Click to collapse
Thank you Awesomeslayerg! Thank you everybody! It's rooted.
Just one problem:
Do you may be know how can I delete this message on the start screen?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Rupdabe-GalaxyS6EdgePlus said:
Thank you Awesomeslayerg! Thank you everybody! It's rooted.
Just one problem:
Do you may be know how can I delete this message on the start screen?
View attachment 5068027
Click to expand...
Click to collapse
It’s in the boot loader files, I removed it it’s possible to hide the warning. I’m busy right now maybe later I’ll upload the file to remove it.

Ok. Thank you

reef2009 said:
Hi I'm familiar with magisk and oneplus, motorola, htc etc but not with Samsung. How can I still upgrade my device without losing root?
My tab S6 lite, notifies me about an upgrade but it looks like it hasn't got an a and B psystem partition so you can love update en before reboot just use magisk to patch the bootloader and keep root. Any suggestions?
Click to expand...
Click to collapse
You cannot install the OTA updates if you are rooted.
Only solution:
* back up of your apps and data with Titanium Backup
* clean install of the new ROM (flashing with ODIN), once the new firmware is available on samfrew.com
* patch the boot.img with magisk, so you are rooted again an can install Titanium
* restore te apps and data with Titanium Backup
Maybe someone can make an update script once we have a TWRP-recovery.
Leuker kan ik het niet maken...

Iceman66 said:
Leuker kan ik het niet maken...
Click to expand...
Click to collapse
thnx!

can someone add me on discord and help me pls
Awesomeslayerg said:
Hey guys,
I know its the same with the other tablets but i wanna make one just cause its easier for people.
How to unlock::
1. Turn on your device and then go to settings --> scroll down to about tablet --> Software Information then tap the Build number 7 or 8 times or until it says you unlocked developer options.
2. Go to developer options and tick OEM UNLOCK and then a warning will pop up and just accept it.
3. Turn off your device, then while holding both volume up and down, connect your device to the pc.
4. A New screen should appear saying stuff about custom roms and stuff, Jut hold and press the up button until it resets. ( THis will erase everything on the tablet)
5. if you're like me and set up the tablet and went straightfoward to unlocking the bootloader, follow this guide: https://forum.xda-developers.com/galaxy-s8/how-to/how-to-bypass-rmm-prenormal-to-install-t3891193
So you wont have any issues flashing roms a nd stuff and dont have to wait 7 days.
6. Now your bootloader should be unlocked! (To enter download/odin mode: Do the same thing, Turn off the device and hold both volume buttons while connecting to the pc then instead of long pressing up, just press up once.)
How to root:
1. Download the firmware for your your tablet, i dont know if i can link the sites but you can google it.
2. Extract only the AP portion of the firmware.
3. Open up the AP portion with 7-zip or winrar
4. extract the boot.img.lz4 out of the AP file
5. Download Lz4 https://github.com/lz4/lz4/releases to your pc corresponding version.
6. Extract the LZ4 to the same area where the boot.img.lz4 is
7. Open command prompt in that folder and then do
Code:
lz4 boot.img.lz4 boot.img
8. Move the boot.img to your tablet, open up magisk manager then clicked Advanced Settings or Advanced, then untick Perserve AVB 2.0/Dm-verity and FIle Encryption then patch it.
9. Take the patched_magisk out of the tablet to your pc and then rename it from magisk_patched.img to boot.img
10. Use 7-zip or winrar and right click on the boot.img and add to archive
11. Select Tar (This is 7-zip havent tried winrar)
12. Once its complete use odin to flash that boot.tar on the AP Section
13. You should now be rooted
Thanks to
@Iceman66
@b0bness
Click to expand...
Click to collapse
Please add me on discord and help me my discord is davin#9999

why is it so complicated to root this tablet, coming from oneplus 2 and then pocophone f1 it was only a 3-4 step process...

Awesomeslayerg said:
It’s in the boot loader files, I removed it it’s possible to hide the warning. I’m busy right now maybe later I’ll upload the file to remove it.
Click to expand...
Click to collapse
Well... You gonna tell us how to do it?

jhill110 said:
Well... You gonna tell us how to do it?
Click to expand...
Click to collapse
Been busy https://forum.xda-developers.com/galaxy-a30/how-to/hide-bootloader-warning-unlocked-t3954589/amp/
Use this guide.

Awesomeslayerg said:
If you don’t know what you are doing, I suggest not rooting your device
Click to expand...
Click to collapse
If you do not buy new devices for sometimes years and are not a native English speaker it can be very hard to figure out what is being written in abbreviations.

ibb.co/XtDpjcT
Hopefully the picture shows however its just a SS of my Root Checker app showing that it is indeed possible to root the tab 6 lite (or at least SM-P610). Since there are plenty of easy to follow guides regarding how to unlock the boot loader for this device i'm going to skip past that part and jump into what actually gave me 12+ hours of frustration.
Once the boot loader is unlocked it is time to find the stock firmware for this device (which I feel its necessary to mention that there are 2 that are almost identical save for literally one number).
1. XAR-P610XXU1BTI3-20200924123941 <---- WRONG!
2. XAR-P610XXU2BTI3-20200924123941 <----- RIGHT!
once you have the correct firmware as seen above and its downloaded onto your computer open the compressed file (I used WinRAR) and you should see 4 different files.
1. AP_P610XXU2BTI3_CL19529942_QB34299355_REV00_user_low_ship_meta_OS10.tar.md5
2. BL_P610XXU2BTI3_CL19529942_QB34299355_REV00_user_low_ship.tar.md5
3. HOME_CSC_OMC_OXM_P610OXM2BTI3_CL19529942_QB34299355_REV00_user_low_ship.tar.md5
4. CSC_OMC_OXM_P610OXM2BTI3_CL19529942_QB34299355_REV00_user_low_ship.tar.md5
The file needed in the next step is the one I have listed as number 1 (beginning with AP). Select just that one and extract it to your desktop. At this point you are going to need a compression software (I used 7Zip which is free). Once you have 7Zip installed right click on the AP file that's on your desktop and just below the open with option you should see an option that says 7 Zip with and extendable sidebar. On that same sidebar the first option you should see is "Open Archive" which you will want to select.
You should now be looking at a window with 8 files and 1 folder however the only file you should be concerned with is the one named "boot.img.lz4". **this is where it gets kinda funky if your not overly familiar with this process**
At this point you will want to go to github.com/lz4/lz4/releases and scroll down a little until you see a download link for a file "lz4_win64_v1_9_2.zip". Once downloaded open the zip and extract the entire folder to your desktop (it should be named LZ by default).
Open the LZ folder and take the "boot.img.lz4" file you extracted earlier and copy it into the LZ folder. Once copied simply Drag and drop "boot.img.lz4" onto the .exe called "lz4". If done correctly a new file should suddenly appear in the same folder that is now simply named "boot" but you will notice that it is now in a Disk Image File format.
(at the end of the guide ill put a URL for a video which shows exactly what I just described here, please follow the video if there is any confusion).
At this point you are going to connect your tab 6 lite to your computer and if it hasn't been done already turn on USB debugging from the developers option and install any drivers needed. Once your tablet and computer are able to communicate (i.e you can open your tablet as a drive on your computer) you will want to copy the "boot" file from the previous step into someplace you will remember (I used my downloads folder). Once onto the tablet you will now download and open Magisk Manager and proceed to patch only this one specific file that you have copied over.
Once patched you should see a copy of the boot file in your downloads folder which will now be named "Magisk_Patched". take this newly patched file and copy in onto your computers desktop.
Rename "Magisk_Patched" to "boot.img" and then right click the file. Again you will want to hover over the 7 Zip option however this time you are going to select the option "add to archive..." which is about halfway down the list. Once selected a new window will come up which will allow you to set the format to .tar. with the name set to boot.tar and .tar selected as the format hit the OK button and on your desktop a new WinRAR Archive file should appear named boot.tar.
Now is when you can finally boot your tablet into Odin mode and open Odin as an Administrator (I used the latest version 3.14.4). Once Odin recognizes your device select the AP button and select the newly created boot.tar as your input (The file location should look similar to this C:\Users\Owner\Desktop\boot.tar provided you saved everything on your desktop like I did).
Once loaded into Odin select the options tab and UN-select Auto Reboot and F. Reset Time before hitting the Start option.
At this point if you did everything correct you should see the boot file being flashed onto the device. Once completed with no errors boot the device into the normal stock recovery and wipe the Cache and then factory reset the device. On the next boot up you should see in addition to the normal "boot loader is unlocked blah blah blah" another message that says you have an illegitimate copy of android on your device and that it may not function or update properly.
Just ignore the message and after a few moments the device should continue to boot into the initial set up page. Work your way through the set up and go online to re-download Magisk Manager. This time when you open the app for the first time it will give you a dialog box that says that the Magisk Operation is incomplete and will ask you if you want to complete it. Agree to complete the process and it will auto run in the background for a moment before it shows completed.
It was finally at this point that I ran Root checker and was met with the very first picture in my post. The biggest Issue I found in all of this was the fact that aside from one single comment in a post here on xda, nowhere else does it explain that you need to extract the boot file, convert it first into an img, THEN patch it, THEN flash it..... smh I cant tell you how many times I wiped my device and had to flash the stock recovery until I got this. I hope this helps you guys moving forward and doesn't just cause more confusion but here are all the links to the videos and files I referenced in order that I mentioned them!
samfrew.com/download/Galaxy__Tab__S6__Lite__-Wi-Fi-__/b0ea/XAR/P610XXU2BTI3/P610OXM2BTI3/(Stock Firmware)
github.com/lz4/lz4/releases (LZ4 converter)
dideo.ir/v/yt/OfrMo1_Rgxc/how-to-convert-android-stock-recovery.lz4-to-img (Video on how to convert .lz4 to .img)
Sorry about all the links being broken up!

Can someone please upload to somewhere faster than samfrew? 200KB/s is beyond stupid...this takes me back to dial up days XD

(GUIDE:) How to ROOT the TAB S6 - SM-T860 (Wi-Fi Model) - (12/10/21):

Hello all,
BORING INTRO STUFF (Safely Ignore This):
I couldn't find any guide that was current enough to make me feel confident in going through with rooting this tablet. So because of that, I decided I would make on my own guide for those that needed this. I tried multiple guides here and all of them resulted in a boot-loop.
VERY SMALL PSA: I'm apologizing in advance if this guide is both pointless and longer than it needs to be. I figured it would be useful as a future reference in-case anyone needed this.
THINGS YOU WILL NEED:
* TAB S6 - SM-T860 (Wi-Fi)
* This can be done on Android 9,10 & 11 (Process is the same)
* Your specific firmware downloaded (*DO NOT SKIP THIS*)
* Tablet is charged to at least 50%
* Maximum of 20 minutes to both read & follow the process
* FIRMWARE: The link below is the firmware I used. I would still advise you to both look for your specific version and to use the link provided below only if your tablet is exactly as followed:
* (T860XXU4CUI4) - BUILD NUMBER
* (ANDROID 11) - ANDROID VERSION
* (XAR - CELLUAR SOUTH) - SERVICE PROVIDER SOFTWARE VERSION
( https://samfirms.com/SM-T860/KOR/T860XXU4CUI4 )
* SAMSUNG USB DRIVERS: ( https://developer.samsung.com/android-usb-driver )
* ODIN: ( https://samfirms.com/download-odin ) Latest is 3.14.4. Use that one or the newest one
* TWRP (OPTIONAL): T860 (Wi-Fi) ONLY. DOWNLOAD VERSION "twrp-3.6.0_9-0-gts6lwifi.img.tar" OR THE LATEST ONE AVAIABLE.
( https://dl.twrp.me/gts6lwifi/ )
* MAGISK APP: ( https://magiskmanager.com/downloading-magisk-manager )
* LZ4 TOOL: ( https://github.com/lz4/lz4/releases )
* 7-ZIP: ( https://www.7-zip.org/download.html )
HOW TO ROOT:
1. UNLOCKING THE BOOTLOADER: *** THIS WILL WIPE YOUR DATA *** (GO TO SETTINGS > ABOUT TABLET > SOFTWARE INFORMATION & TAP BUILD NUMBER 7 TIMES. GO TO DEVELOPER OPTIONS > TOGGLE ON OEM UNLOCKING) TURN OFF THE TABLET. AT YOUR PC, HAVE A CABLE CONNECTED TO THE PC. WHILE HOLDING BOTH VOLUME DOWN + VOLUME UP, PLUG IN THE CABLE. WHEN THE SCREEN TURNS ON, PRESS AND HOLD VOLUME UP.
WHEN THE SCREEN CHANGES PROMOTING YOU TO UNLOCK THE BOOTLOADER, PRESS VOLUME UP. ONCE BOOTED UP, GO THROUGH THE SETUP AGAIN AND MAKE SURE Wi-Fi IS CONNECTED. GO BACK TO SETTINGS, ENABLE DEVELOPER OPTIONS AGAIN AND THEN ENABLE USB - DEBUGGING.
2. EXTRACT THE BOOT.IMG.LZ4 FILE AND MOVE IT TO YOUR TABLET: After 7-Zip is installed, the LZ4 Tool and the firmware you downloaded is extracted somewhere, open the extracted firmware folder. Right-click on the AP file and select 7-zip then open archive. Look for boot.img.lz4, drag it inside of the LZ4 Tool. Once done, drag the boot.img.lz4 on top of the LZ4 executable. It will be extracted as boot.img. Right-click the boot.img file and select 7-zip then add to archive. Change "Archive format" to tar and rename it to boot.tar. Finally, move it to your tablet's storage.
3. DOWNLOAD THE MAGISK APK: Install the Magisk apk that you downloaded and open it up. Within the app, select install, uncheck recovery mode and press next then check "Select and Patch a file". Locate your boot.tar file that you moved into your storage from earlier and wait for Magisk to process it.
4. USING ODIN: Go ahead and locate the new file, it starts with Magisk (NOT THE BOOT.TAR FROM EARLIER SHOULD START WITH MAGISK). Once done, move the Magisk tar file to your computer and turn off the tablet. With the tablet off and Odin open (Run as administrator) , press and hold both VOLUME DOWN & VOLUME UP then plug the cable from your pc into your tablet. With Odin open, go into the "options" tab, uncheck "Auto Reboot" and Select "AP". Locate the Magisk tar file you moved from your tablet and then press "Start".
ONCE IT SAYS "PASS" THEN STOP AND READ THIS BEFORE CONTINUING. *IMPORTANT*
PRESS AND HOLD BOTH POWER AND VOLUME DOWN FOR 7 SECONDS. THE SCREEN WILL TURN BLACK. VERY QUICKLY WHILE STILL HOLDING POWER, PRESS AND HOLD VOLUME UP INSTEAD. PRESS POWER TO THE BOOTLOADER UNLOCK PROMPT AND YOU SHOULD BE IN RECOVERY. THIS SHOULD BOOT YOU INTO STOCK RECOVERY. USE THE VOLUME KEYS TO NAVIGATE, SELECT "Wipe data/factory reset" then press the power button and select "Factory data reset". Finally, select "Reboot system now" and Wait for the tablet to reboot into the OS.
5. FINISHING UP: After the tablet has restarted back into android and you took a couple of minutes to go through the setup one last time. Scroll up into the app drawer and make sure that you see the app "Magisk", go ahead and select it and press ok to download Magisk. Afterwards, open it up and Magisk will ask you to reboot to finish setting up root. Press ok. Once restarted you are done with the rooting process.
Lastly, as an optional step you can install TWRP.
6. TWRP INSTALLATION (OPTIONAL): With the tablet off and Odin running on your pc, go ahead and press VOLUME DOWN AND VOLUME UP at the same time then plug in the data cable from your PC. Press VOLUME UP to go into download mode. Once in download mode, select "AP" then select the TWRP tar file you downloaded and make sure to uncheck "Auto reboot" from the options tab in Odin. Click start and after it says "PASS" unplug the data cable. On the tablet, press VOLUME DOWN AND POWER to reboot and when you see THE SCREEN TURN BLACK, QUICKLY PRESS AND HOLD BOTH POWER AND VOLUME UP. You should be in TWRP and you are now officially done.
* From now on, I would recommend you use the Magisk app or some reboot app to boot into recovery as it is difficult to use the button combinations to access recovery.
* IF YOU'RE NOT USING MAGISK TO REBOOT TO RECOVERY, I WOULD USE THIS APP INSTEAD: https://play.google.com/store/apps/details?id=com.eypcnnapps.quickreboot&hl=en_US&gl=US
Credits: If all went well then I appreciate you taking the time to read through this guide carefully. Hope it was as clear as possible and that you found it helpful. I will be editing this post from time to time to make it cleaner.
Again, Thank you and if you have any questions, I will answer them when I see them.

THANK YOU SO MUSH IVE BEEN STRUGGLING SO HARD TO GET ROOT ON THIS TABLET FINALLY THANK YOUUUUUU
by the way guys, when it says to reboot to make magisk work.
you are risking a bootloop.

Oh by the way, aside from TWRP being wonky thank you for the guide I had been playing with the idea of rooting this thing for over a year now. You made it easy.
I go through all the steps and it works fine. Once I try for TWRP I end up with
"partition recovery
Reason recovery: Error verifying vbmeta image: invalid vbmeta header (6)
CUSTOM recovery
VBMETA T860XXU4DVG6, 54204454R"
From that point it just loops back to that message and downloading mode until I wipe it all and start over again. I TWRP a no go for the S6 now? I guess I can dig around on their site as well. Any input anyone wants to throw my way will also be appreciated.

Hi Sadistic - ,
I need to start with a complement. This is a really clear guide.
But, When I get done with step 3, the Magisk patched boot file has a .img extension
On step 4, Odin is expecting a .tar file extension so the file doesnt show up.
Did I miss something?
Thanks

mvanwey said:
Hi Sadistic - ,
I need to start with a complement. This is a really clear guide.
But, When I get done with step 3, the Magisk patched boot file has a .img extension
On step 4, Odin is expecting a .tar file extension so the file doesnt show up.
Did I miss something?
Thanks
Click to expand...
Click to collapse
Yep..... try step 2

seppukuudere said:
Yep..... try step 2
Click to expand...
Click to collapse
Yes, step 2 is moving the extracted boot file (re-named to .tar) to my tablet and then patching it with magisk.
The patched file from Magisk has an .img extension.

mvanwey said:
Yes, step 2 is moving the extracted boot file (re-named to .tar) to my tablet and then patching it with magisk.
The patched file from Magisk has an .img extension.
Click to expand...
Click to collapse
Ah I see, I would try to do step 3 again, take screenshots of the end result from magisk o:

Let's just cancell this. it was over 20 days since I asked for help & now I'm getting asked for screenshots.
I have moved on.
I probably should have put that in my reply.

mvanwey said:
Let's just cancell this. it was over 20 days since I asked for help & now I'm getting asked for screenshots.
I have moved on.
I probably should have put that in my reply.
Click to expand...
Click to collapse
oops yikes, yeah probably should have. happy new year!

seems like after rooting mine the storage has been cut by a big margin, from 128 to 32gb. any way of fixing this?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Hi. Is there any update guide for last android 12 version, to install twrp? Can se still use this, as it is for android 11?
Thanks,