Smart Switch doesn't update phone - Verizon Samsung Galaxy S6

Hello, I have a problem with Smart Switch, I conected my phone and it showed that an firmware update was available so I proceeded to install it, however after the app downloads the update my phone just turns off and enter to download mode (everything normal) but in the installation process it doesn't install anything it just show 0% of the installation , after a few minutes and error message appears showing : "Failed to recognize software update mode" in my phone screen doesn't appear no error image, it just show the typical download mode image.
-My Baseband V. is G920VVRS4CQA3.
-Android 6.0.1
-Model. Obviously SM-G920V
Current version installed: at the attached files (Or da.png)
Message that appears before the error window. 2nd attached file (Or dadd.png)
Window showing the "notice". 3rd attached file (Or daddsw.png)
And a image from the download mode that it's on my screen (not mine). 4rth attachment (Or dae.png)
I hope that someone could help me. My many thanks in advance.

Related

Update Samsung Galaxy FIT S5670 with Official Gingerbread DDKT1 2.3.6 Firmware

pre Requisites:
- All the data present in your Galaxy FIT needs to be backed up ONLY by following the below mentioned steps so as to ensure that just in case if the data gets lost or corrupted.
- Charge left in the device should be minimum 60% so as to make sure that the phone doesn’t get turned Off in the middle of firmware update. Enable the USB Debugging in your device from the path “Settings > Applications > Development > USB debugging”
So,assuming that you have followed all the instructions mentioned above you now need to proceed further for procedure.
Procedure to Update
- Download Gingerbread 2.3.6 Package & odin-beni-ss.dll for Fit.zip in your computer after which you need to extract the same.If Promted For Password then You Should Enter Password as “sampro.pl”.
For 2.3.6 Update Package- http://hotfile.com/dl/140199372/0b98375/GT-S5670_INU_S5670DDKT1_S5670ODDKT1_S5670DDKT1.rar.html
- Match the extracted files from the below shown screen capture, even if single file is missing then you need to check with the extraction or download process.
- From extracted files, open Odin executable file and turn Off the phone so as to enter the device in the download mode.
- Now, you need to enter the by holding the Volume Down button + the Home key button (the middle button). While holding these both buttons, you need to switch ON your device. Just in case if the device boots in the normal mode then you will have to again try the process of entering into the download mode
- After entering the phone in the download mode, connect the device to the computer while keeping the Odin opened. Within a minute, the ID : COM section will turn yellow which will mean that all the drivers have been successfully installed and you are now ready to proceed to the next step.
- Click on the “OPS” option in the Odin to select the below mentioned file, tick on “One Package” option and then select the One Package option as mentioned below.
OPS – BENI_v1.0.ops
One Package – S5670DDKT1_S5670ODDKT1_S5670DDKT1_HOME.tar.md5
- Click on Start and then wait for the device to get restarted. Once the device gets restarted, you will be asked to enter the Google Account credentials. Once you see the home screen in your phone, disconnect the connected phone.
Congratulations!!! You have successfully update ur android with 2.3.6 Gingerbread Firmware
_______________________________________________________________
Press THANKS button If I help U in any manner
Hi!
Does this firmware includes greek language?Thanks!
may be no...
Because DD is for india:thumbup:
Sent from my GT-S5670 using xda app-developers app
Do you know where i can find or what is the name for the firmware to search?Also i have a greek galaxy fit with 2.3.6,do you know how to make a full backupo of this firmware?Thanks!
i guess everyone knows this
zafisinl said:
Do you know where i can find or what is the name for the firmware to search?Also i have a greek galaxy fit with 2.3.6,do you know how to make a full backupo of this firmware?Thanks!
Click to expand...
Click to collapse
http://www.sammobile.com/firmware/
In search write s5670.
password
what is the password for this file????
It's witten over there on sammobile
Sent Via XDA™ Premium
Password
rajmi said:
what is the password for this file????
Click to expand...
Click to collapse
Read the first post carefully
Pasword : sampro.pl
The rar file just has the md5 file, where can I find the other files? I tried manually downloading the files from different locations but it just sits at downloading mibib and doesn't do anything. The flashing process just sits at downloading MIBIB and doesn't go anywhere, I have tried waiting for as long as 30mins, now the mobile doesn't even start with the previous firmware. When started it shows an icon like connection problem between a computer and mobile right after the initial samsung logo and sits there.Please help
zafisinl said:
Hi!
Does this firmware includes greek language?Thanks!
Click to expand...
Click to collapse
Most probably it does.I flashed mine with a stock russian rom.the phone started in russian but you can easily navigate through the icons to settings and change the language.I turned it to greek

[Help] Install new ROM

Hello guys, i'm new on the world of Android and i need a little help. I'm newbie but i learn fast.
I got a new phone with android 4.4.2 China honor 3 (fake), after uninstalling some China app the operation system started to stuck at logo at the start.
So to solve the problem i red that i could restore the old OS using ROM file. The factory where i bought the phone sent me the official ROM file for my phone.
Now i entered on Recovery mode, first i did "wipe data/factory reset", then with ADB i loaded the file .zip "adb sideload update.zip". But how the file is uploaded it says "Installation aborted", without any error.
So now i need your help how can i restore this system... I tried also to buy an SD card 8 gb and upload the file on the SD, but same error.
Thank you for your help!
try this guide
http://forum.xda-developers.com/showthread.php?t=2517943
bcuz you can;t flash rom with stock recovery so you install cwm mod from this guide:fingers-crossed:
3lo0sh said:
try this guide
http://forum.xda-developers.com/showthread.php?t=2517943
bcuz you can;t flash rom with stock recovery so you install cwm mod from this guide:fingers-crossed:
Click to expand...
Click to collapse
Thank you for the answer. But wheni try to run TouchRecoveryLoader.zip from recovery, it says "installation aborted" like for the ROM.
I dont know if the phone got root access, i think this can be the problem.
Can youhelp me?
Thank you
Bump! Need help guys
SUMMARY:
I unistalled wrongly MIUI (MiHome app) and the phone stopped working correctly.
Phone is a fake honor 3c with MTK 65xx processor.
1 - Phone doesnt load the main theme, after the android logo i see a black page. (i see the top bar where there are wifi, time etc)
2 - The phone is not rooted. (i think)
3 - I can enter in Restore Mode and Factory Mode.
4 - I got the official ROM file. (the factory gave me it)
5 - All file zip (that i try to use in recovery from SD or ADB) give me "Installation aborted" without any error.
6 - I haven't USB DEBUG enabled, and i can't enable it cause i can't load the Operation system.
shayolz said:
Bump! Need help guys
SUMMARY:
I unistalled wrongly MIUI (MiHome app) and the phone stopped working correctly.
Phone is a fake honor 3c with MTK 65xx processor.
1 - Phone doesnt load the main theme, after the android logo i see a black page. (i see the top bar where there are wifi, time etc)
2 - The phone is not rooted. (i think)
3 - I can enter in Restore Mode and Factory Mode.
4 - I got the official ROM file. (the factory gave me it)
5 - All file zip (that i try to use in recovery from SD or ADB) give me "Installation aborted" without any error.
6 - I haven't USB DEBUG enabled, and i can't enable it cause i can't load the Operation system.
Click to expand...
Click to collapse
if you open the zip file you got, whats inside it? is it a .tar file, or a .md5 file?
Sorry, i didn't write that i SOLVE the problem!
I userd flash tool selecting only "ANDROID" and pointing to the system.img of the ROM that the factory gave me.
Android reinstalled, all working fine.
/closed
thanks

[Q] Plz help me save my Lenovo A328

I have just bought t this afternoon. after I could not copy one file to the system folder, I set permission for this folder as 644. then my screen phone turned black and could not reboot. I tried to reboot it over and over but it failed again. on the start screen, it shows an android icon with phrase "No command". I could not enter any function above it (reboot system now, apply update from sdcard...)
I have downloaded a stock rom from the internet but did not know how to flash it. can anyone help me plz? thank so much
enter recovery mode and flash via recovery you will get all the information from your device thread here
http://forum.xda-developers.com/t/lenovo-a328
you can donwload the recovery or anything from there and all info will be available in the device specified section

Downgrade Asus ME175CG From Lollipop to kitkat

Before starting the thread, I want to thank Mr. social-design-concepts on the important Thread Intel Android Devices Root
in this thread i will show steps to downgrade asus me175cg k00z from lollipop to kitkat
Everything you do at your own risk
​
1 : download and extract IntelAndroid-FBRL-07-24-2015.7z some where on your computer.
https://www.dropbox.com/s/oqtir228a4qjahg/2. IntelAndroid-FBRL-07-24-2015.7z?dl=0
https://drive.google.com/open?id=0BxuGFyMwQmSjblZBOEdrN0dwYmM
use 7z to extract
https://www.dropbox.com/s/fk8bspkgrnt3vdr/1. 7z installer.rar?dl=0
https://drive.google.com/file/d/0BxuGFyMwQmSjcDBJMDF5WHVvLXM/view?usp=sharing
or torrent as attachment
2. Download Me175CG firmware:
http://www.asus.com/support/Download/28/7/0/6/32/
copy downloaded file to The root of your external MicroSdcard
3 : double click the launcher.bat file to start , type " ACCEPT " case sensitive without quotes to continue
check that the tool is reporting as either :
DEVICE STATUS: ADB-ONLINE
DEVICE STATUS: FASTBOOT-ONLINE
If " DEVICE STATUS: UNKNOWN " please check your cable connection and driver installation under
Windows Device Manager
If " DEVICE STATUS: UNAUTHORIZED " please check if your devices is displaying an authorization
prompt be sure to check Always allow from this computer and then press ok
4 : select the trigger to launch the Temporary CWM Recovery Session support fastboot oem triggers are :
T2 oem backup_factory
(devices supported : K00Z Me175CG)
(use T2 option or ME175CG K00Z)
5 : after selecting the trigger your device should reboot in to fastboot and begin to copy files to your device
note : if your device hangs at the waiting-for-device screen and you see droidboot CMD Waiting on your devices double check that the fastboot driver installed correctly.
note : if you see unknown oem command the trigger isn't supported by your device.
6 : The temporary cwm recovery session should be started at this point select install zip from the recovery menu using vol up / vol down to navigate and power to select
7 : select install zip from sdcard / external_sd depending on where you placed the file and select the "UL-K00Z-WW-5.5.1.0-user.zip" (you downloaded earlier)
8 : confirm the installation
9 : after install completes reboot your device
Now your k00z have been downgraded to kitkat firmware you can root it via this method
http://forum.xda-developers.com/showpost.php?p=53639853&postcount=66
For those users of ME175CG affected by the "battery drain issue" after upgrading to OTA v6.3.9, I've created a change.org petition requesting ASUSTek to fix this bug. Please support by signing this petition (It'll hardly take a couple of mouse clicks):
https://www.change.org/p/asustek-pl...ium=email&utm_campaign=share_email_responsive
hi frends i pdated my " me 175 cg ww " to last ota update and now i have call and network and battery problem can i downgrade by this method to kitkat??? which version of frimware i must to flash ?
i afraid lose my imie because i do my internet job with my tablet
thank a lot devs. waiting for answer ....
this method worked for me thank u man
thank u xda devs
asus fonepad me175cg dual sim ww
4.4.2 is lovely
omar.sch said:
Before starting the thread, I want to thank Mr. social-design-concepts on the important Thread Intel Android Devices Root
in this thread i will show steps to downgrade asus me175cg k00z from lollipop to kitkat
Everything you do at your own risk
​
1 : download and extract IntelAndroid-FBRL-07-24-2015.7z some where on your computer.
https://www.dropbox.com/s/oqtir228a4qjahg/2. IntelAndroid-FBRL-07-24-2015.7z?dl=0
https://drive.google.com/open?id=0BxuGFyMwQmSjblZBOEdrN0dwYmM
use 7z to extract
https://www.dropbox.com/s/fk8bspkgrnt3vdr/1. 7z installer.rar?dl=0
https://drive.google.com/file/d/0BxuGFyMwQmSjcDBJMDF5WHVvLXM/view?usp=sharing
or torrent as attachment
2. Download Me175CG firmware:
http://www.asus.com/support/Download/28/7/0/6/32/
copy downloaded file to The root of your external MicroSdcard
3 : double click the launcher.bat file to start , type " ACCEPT " case sensitive without quotes to continue
check that the tool is reporting as either :
DEVICE STATUS: ADB-ONLINE
DEVICE STATUS: FASTBOOT-ONLINE
If " DEVICE STATUS: UNKNOWN " please check your cable connection and driver installation under
Windows Device Manager
If " DEVICE STATUS: UNAUTHORIZED " please check if your devices is displaying an authorization
prompt be sure to check Always allow from this computer and then press ok
4 : select the trigger to launch the Temporary CWM Recovery Session support fastboot oem triggers are :
T2 oem backup_factory
(devices supported : K00Z Me175CG)
(use T2 option or ME175CG K00Z)
5 : after selecting the trigger your device should reboot in to fastboot and begin to copy files to your device
note : if your device hangs at the waiting-for-device screen and you see droidboot CMD Waiting on your devices double check that the fastboot driver installed correctly.
note : if you see unknown oem command the trigger isn't supported by your device.
6 : The temporary cwm recovery session should be started at this point select install zip from the recovery menu using vol up / vol down to navigate and power to select
7 : select install zip from sdcard / external_sd depending on where you placed the file and select the "UL-K00Z-WW-5.5.1.0-user.zip" (you downloaded earlier)
8 : confirm the installation
9 : after install completes reboot your device
Now your k00z have been downgraded to kitkat firmware you can root it via this method
http://forum.xda-developers.com/showpost.php?p=53639853&postcount=66
Click to expand...
Click to collapse
thank a lot!:good::good::good:
this method saved my tablet!! I almost had discarded it!!
some notes:
after installation and reboot my tablet stuck on asus logo few reboot didn't solve it. so i entered boot menu and performed a factory reset. then it passed asus logo and every things got OK except some force close messages on google services such as google play and google apps. I think update will solve them.
< waiting for device >
what should i do ?
Thanks, man
thanks a ton, yaar. your post saved my tab. I was enduring the man-made disaster (Lollipop update to FonePad7) for more than an year. Actually used it exclusively as a WiFi device due to buggy telephony software. This had been a global phenomena, still ASUS didn't care to release a downgrade option. Not even acknowledge it. I contacted their customer care and was advised to take the tab to service center!!! (what is he going to do if the company doesn't have an official downgrade option?). I was really impressed by the quality of ASUS hardware and also bought Zenfone2 for my wife.
But now i learnt my lesson: NO MORE UPDATE AND NO MORE ASUS.
Asus ME1775CG
ASUS me175cg Lollipop ww 6.3.9. In normal mode PC detects both internal and external memory. But when It boots to droid boot mode it shows "no usb cable connected" and selecting "install from sd card" option shows "unable to mount the sd card partition" How to solve this issue.
System recharge status
Hello to all,
I followed the whole process of downgrading to the letter;
but I think something went wrong .........
After installing the firmwear and restarting the tablet ......
remains in the system recharge screen .........
that is, the asus logo with the circle that loads ......
what can I do to remedy this ......?
I need help.......
roma73 said:
Hello to all,
I followed the whole process of downgrading to the letter;
but I think something went wrong .........
After installing the firmwear and restarting the tablet ......
remains in the system recharge screen .........
that is, the asus logo with the circle that loads ......
what can I do to remedy this ......?
I need help.......
Click to expand...
Click to collapse
I have absolutly the same problem.What is the solution?

how to fix not booting phone after installing twrp

If your y5 2017 mya-l22 not booting, showing empty battery and loop but not charging...
Here is how to fix it...
Prerequisite:
You need SP drivers for this phone, find it on 4pda forum.
0. Make sure to disconnect the USB.
1. Download latest SP flash tool " search for it using Google"
2. Download b123 firmware from the link below , then extract it.
http://www.mediafire.com/file/77on9pxha4mzmmw/Huawei_y5_2017_MYA-L22_MT6737_C185B123_6.0.zip
3. Edit scatter file from b123 by deleting last 2 lanes,
"""
[huaqin]
CheckSum = 0xf302
"""
4. Open SP flash tool,press on Download tab, then Load the scatter file from b123 firmware ,it will take sometime.
5. Press the download button "Green arrow "
6. Now on phone, Press and hold the " down volume " button and plug the USB cable the flashing will start automatically .,,,, Keeeeeeep holding the down volume button until the " yellow" bar start to progress
Note1 : select "download only " I think it's enough , I by mistake chosen format all + download but that broke the imei and baseband :/ . There's a workaround but ". NEVER CHOSE FORMAT ALL + UPGRADE".
Note2 : make sure to make the firmware path and the scatter file path very short and of ASCII characters only to avoid problems,. For example c:/fw/scatter.txt
i have the same problem(its L125).I downloaded the firmware for l125 and flashed as per your instructions.But its still stuck in the loop.
I used the DA mtk all in one. Should i try format and flash?
anandumohan said:
i have the same problem(its L125).I downloaded the firmware for l125 and flashed as per your instructions.But its still stuck in the loop.
I used the DA mtk all in one. Should i try format and flash?
Click to expand...
Click to collapse
No, don't format, it will make it worse.
Are you sure that you have selected all partitions to before pressing download, and then it showed a "Success" message ? ,, you may try to repeat the process, it should work because it will restore the phone to the factory codition!
salembream said:
No, don't format, it will make it worse.
Are you sure that you have selected all partitions to before pressing download, and then it showed a "Success" message ? ,, you may try to repeat the process, it should work because it will restore the phone to the factory codition!
Click to expand...
Click to collapse
Yes I selected all the partitions and it showed a green tick with success.
anandumohan said:
Yes I selected all the partitions and it showed a green tick with success.
Click to expand...
Click to collapse
i have same problem to, my huawei y5 2017 cant stop blinking after instal twrp recovery.
and i try this step but still it keep blinking . pls help
salembream said:
If your y5 2017 mya-l22 not booting, showing empty battery and loop but not charging...
Here is how to fix it...
Prerequisite:
You need SP drivers for this phone, find it on 4pda forum.
0. Make sure to disconnect the USB.
1. Download latest SP flash tool " search for it using Google"
2. Download b123 firmware from the link below , then extract it.
http://www.mediafire.com/file/77on9pxha4mzmmw/Huawei_y5_2017_MYA-L22_MT6737_C185B123_6.0.zip
3. Edit scatter file from b123 by deleting last 2 lanes,
"""
[huaqin]
CheckSum = 0xf302
"""
4. Open SP flash tool,press on Download tab, then Load the scatter file from b123 firmware ,it will take sometime.
5. Press the download button "Green arrow "
6. Now on phone, Press and hold the " down volume " button and plug the USB cable the flashing will start automatically .,,,, Keeeeeeep holding the down volume button until the " yellow" bar start to progress
Note1 : select "download only " I think it's enough , I by mistake chosen format all + download but that broke the imei and baseband :/ . There's a workaround but ". NEVER CHOSE FORMAT ALL + UPGRADE".
Note2 : make sure to make the firmware path and the scatter file path very short and of ASCII characters only to avoid problems,. For example c:/fw/scatter.txt
Click to expand...
Click to collapse
Hi, can you give me the workaround on "format all + download ". I tried it and now I'm in Dip S**t (sorry for that) but I'm really frustrated right now. TIA
Hello, I have a problem I downloaded everything, but my phone does not start , I hold the " down volume" ,But there is only a logo and nothing happens, the pc has no contact except thanks to the usb hooking,scaler is correct? , the phone has stopped working after TWRP installation
Egooo said:
Hello, I have a problem I downloaded everything, but my phone does not start , I hold the " down volume" ,But there is only a logo and nothing happens, the pc has no contact except thanks to the usb hooking,scaler is correct? , the phone has stopped working after TWRP installation
Click to expand...
Click to collapse
It won't show any thing while flashing, if you did it correctly after flashing disconnect the USB cable then reconnect it ,,, better on charger and wait some time and turn on the phone
salembream said:
It won't show any thing while flashing, if you did it correctly after flashing disconnect the USB cable then reconnect it ,,, better on charger and wait some time and turn on the phone
Click to expand...
Click to collapse
I tried this, as although twrp was never installed, i had the same issue described - on charge it would show red led, battery logo, then black screen, red led and so on til infinity, i have had it on charge for 3 days with this cycle endlessly repeating.
The flashing with sp tool went fine, at least it reported it as successfully flashing, and when i put it on charge i just got the red led, without the battery symbol, yay!
But then I pressed the power button (not for the 3 secs required to power the phone on) and now its back in the same cycle as before, and when i try to use sp tool now, i get timeout errors or another vague one that says to check the power on the device, at any rate its not letting me try to flashing process again.
As it had no charge when the process worked, i'm not sure whats going wrong now :/
any pointers? thanks!
Mine worked... I had the same problem...
I used sp flash tools.. As we load the scatter files from the firmware folders. I loaded the scatter files..
Firstly I choosed only the boot files and e recovery files not the system files from the scatter file...because the battery was not charged....as it flashed i plugged in charge for about 30 minutes... Then i unplug it.. and then flashed the remaining files from the scatter files like system...
Then again i plugged it in charge... NOW it is showing battery icon and it is charging and percentage is increasing... It was zero(0) at initial....
I found out the problem is due to lack of charge of battery...
Thank you
U can email me at - [email protected]
Thank you
Fix boot problem
Dont wary. It worked for me with B126 firmware with sp flash tool.
Use mauimeta too for fixing invalid imei error.
salembream said:
If your y5 2017 mya-l22 not booting, showing empty battery and loop but not charging...
Here is how to fix it...
Prerequisite:
You need SP drivers for this phone, find it on 4pda forum.
0. Make sure to disconnect the USB.
1. Download latest SP flash tool " search for it using Google"
2. Download b123 firmware from the link below , then extract it.
http://www.mediafire.com/file/77on9pxha4mzmmw/Huawei_y5_2017_MYA-L22_MT6737_C185B123_6.0.zip
3. Edit scatter file from b123 by deleting last 2 lanes,
"""
[huaqin]
CheckSum = 0xf302
"""
4. Open SP flash tool,press on Download tab, then Load the scatter file from b123 firmware ,it will take sometime.
5. Press the download button "Green arrow "
6. Now on phone, Press and hold the " down volume " button and plug the USB cable the flashing will start automatically .,,,, Keeeeeeep holding the down volume button until the " yellow" bar start to progress
Note1 : select "download only " I think it's enough , I by mistake chosen format all + download but that broke the imei and baseband :/ . There's a workaround but ". NEVER CHOSE FORMAT ALL + UPGRADE".
Note2 : make sure to make the firmware path and the scatter file path very short and of ASCII characters only to avoid problems,. For example c:/fw/scatter.txt
Click to expand...
Click to collapse
thank you sir

Categories

Resources