I have a problem with MTCD_KSP unit it sometimes goes blank and turn on after 3-4 hours.
My vedor offered me a different unit with some android tablet version installed on it.
Should i go with it or not.
Please find screen shot of about device page for both units.
Why don´t you try to update MCU with a newer version?
Related
So, have a bit of a situation and not sure what to do.
My touch screen is working, but only to a point. Only the top status bar and bottom about the same size does not respond at all across.
I've attached a picture as an example of which part of the screen highlighted in red does not respond at all to touch. Everything else not highlighted in red works fine.
Have used my mouse to access boot recovery mode, reinstalled hal 9k mod rom, wiped cache / data and it made no difference.
Even updated my MCU to the latest version available for HA unit, and attempted to re-calibrate the screen via extra settings.
Not sure if original factory rom will fix this, but would like some opinions.
maybe take it apart and check the screen connector is in correctly, sounds like a hardware not software problem.
darkphat said:
So, have a bit of a situation and not sure what to do.
My touch screen is working, but only to a point. Only the top status bar and bottom about the same size does not respond at all across.
I've attached a picture as an example of which part of the screen highlighted in red does not respond at all to touch. Everything else not highlighted in red works fine.
Have used my mouse to access boot recovery mode, reinstalled hal 9k mod rom, wiped cache / data and it made no difference.
Even updated my MCU to the latest version available for HA unit, and attempted to re-calibrate the screen via extra settings.
Not sure if original factory rom will fix this, but would like some opinions.
Click to expand...
Click to collapse
Hi,
I have similar problem on my px5 seicane unit. the bottom part touch screen won't response or acting without touch after wake up from sleep. restart the unit would result the issue.
wondering if you have resolved the problem? If so is that hardware issue?
just realized the touch screen issue I have on my headunit is probably hardware issue.
in the past I have to re-start the unit, that actually fixed the problem, don't know why. but now I just push the touch screen with my palm firmly. that would fix the problem as well, and last much longer (3-5 days). haven't get chance during the weekday to open up the unit. but at least it worked. and probably proofed this is hardware issue.
I have a Joying unit with a PX5 board. I also have the same issue as the original poster.
I would also say this is a hardware issue. Mine was fine with both the original PX3 and PX5 for a while. Now it is increasingly getting worse. Resets do nothing to solve the problem.
I live in a hot environment. Maybe that is a contributing factor?
hello everyone
i am hoping that you guys will be able to help me out. i have an xtrons head unit 10.1 inch double din running 5.1 firmware. i reached out to the people that sold it to me about updating to a newer firmware and they told me i can only update the software. they sent me a file that would update my software with instructions. i updated my unit now the back light that lights up the touch buttons does not work neither does the power, volume up, down or home the back button does work but instead of going back it raises the volume. i can not turn the head unit off only when the car ignition gets turned off. i tried to use a remapping app but it doesn't seem to find the buttons that i want to remap. the sellers are not offering any help because it is 3 months past the warranty. xtrons told me the radio is discontinued and are also not offering any help this is what was on the file they sent HH 通用机安卓5.1(20170307)_rk3188_5.1.rar
p.s i also attached a photo of the info that the radio has i am not sure if when i updated it if it changes the info. thanks for any help that you guys can provide
Have you tried going into the factory settings and entering the touch calibration menu?
If you go to settings, factory settings (password is "126" without the quotes) and go to the touch panel calibration there's one to calibrate the touch screen and another one that says "touch panel" or front panel.
Play around with that menu and that should solve your problem.
thanks for helping me as fast as you did. it did work i also found a video on YouTube that might help other with this same problem. https://www.youtube.com/watch?v=I27cjq0SUTk
homer.ali said:
Have you tried going into the factory settings and entering the touch calibration menu?
If you go to settings, factory settings (password is "126" without the quotes) and go to the touch panel calibration there's one to calibrate the touch screen and another one that says "touch panel" or front panel.
Play around with that menu and that should solve your problem.
Click to expand...
Click to collapse
how udate xtrons 10.1
I have the same radio xtrons 10.1 with version 5.1.1, which I want to update, could you give me the rom file?
rdptrix said:
hello everyone
i am hoping that you guys will be able to help me out. i have an xtrons head unit 10.1 inch double din running 5.1 firmware. i reached out to the people that sold it to me about updating to a newer firmware and they told me i can only update the software. they sent me a file that would update my software with instructions. i updated my unit now the back light that lights up the touch buttons does not work neither does the power, volume up, down or home the back button does work but instead of going back it raises the volume. i can not turn the head unit off only when the car ignition gets turned off. i tried to use a remapping app but it doesn't seem to find the buttons that i want to remap. the sellers are not offering any help because it is 3 months past the warranty. xtrons told me the radio is discontinued and are also not offering any help this is what was on the file they sent HH 通用机安卓5.1(20170307)_rk3188_5.1.rar
p.s i also attached a photo of the info that the radio has i am not sure if when i updated it if it changes the info. thanks for any help that you guys can provide
Click to expand...
Click to collapse
balon2018 said:
I have the same radio xtrons 10.1 with version 5.1.1, which I want to update, could you give me the rom file?
Click to expand...
Click to collapse
Send me your email I will look it up tomorrow in my files and forward it over to you
Hi,
This is my first post on this forum and i am hoping members here will help me solve my issue. I have a Honda HR-V 2016 LX that came with a non android unit. I later purchased a Honda Navi unit from ebay UK that was pulled from a Honda HR-V 2017. The unit worked fine and later I downgraded to RC6 firmware so that I could install additional software from CMdroid. The problem started when i tried to change the skin through system settings, the unit gave a notification that system will restart and since then it is in continuous boot loop. Now this is what i have done till now :
a. disconnected battery for over 15 minutes. No change
b. tried to boot the system through USB with firmware RC6, It updated fine with progress bar and at the end got the message update successful and USB can be disconnected but at restart it still remained in that loop.
c. Again booted with USB having RC8 successfully but no luck
I feel that I need to do a factory reset to get my audio working again but unfortunately it is not booting up to the point that soft keys get illuminated. The reverse screens powers up but without guidelines. I don't want to lose my unit. Please help me recover it.
Regards
Members I need help here. Please some one suggest me a solution to get my audio unit working again. Today I reinstalled the firmware and it went smooth but on restart the system continues to reboot.
Hi Panther3, did you ever get to the bottom of this, the same thing has just happened to mine?
Scooterpop said:
Hi Panther3, did you ever get to the bottom of this, the same thing has just happened to mine?
Click to expand...
Click to collapse
I actually have a 2nd honda navigation unit that has this issue... Been trying to work on it but no luck till now...
So I am curious if someone manages to make it work ^^
here is the official solution from the manual... :
Some units might experience "H screen stuck on"
symptom. Initially the software update will not be
possible when the unit is "H screen stuck on". You will
need to follow these steps before attempting the
update:
• When unit is in fail mode "H screen stuck on",
Press and hold the Power and Day Night button at
the same time for five seconds.
Note: Wait until the loading circle appears on the
screen and then press the Power & Day Night
button.
After five seconds the unit will switch into the
reboot mode, then the unit will do a file check
during rebooting. Rebooting will take
approximately two and a half minutes.
• Now continue with software update procedure.
Note: The "H screen stuck on" symptom can be
caused by software or a hardware failure. In case of
a hardware failure, recovering is not possible and a
new RM unit is necessary.
Click to expand...
Click to collapse
Hi,
First of all, please excuse me if I have post on the wrong forum. I really searched a lot for a similar question but haven't found it. My unit's MCU versoin is MTCE_CZ_V3.10_2, so I don't know if it's really a "MTCE" head unit, but I don't see a MTCE specific sub-forum (by the way, what does the MTCD, MTCB and so on nomenclature mean?). I got this unit from AliExpress about a year and a half ago, it's a 4 GB, octa-core [email protected] version, with 64 GB internal memory and DVD, for Vauxhall/Opel Corsa, and this is the current (updated) product page for it:
https://www.aliexpress.com/item/32789005299.html?spm=a2g0s.9042311.0.0.27424c4dbyAN90
It currently displays a PX6 version; mine is the PX5 one.
Well, the problem with the unit happend a few weeks after I installed it on my car. Suddenly, one time, when I started my car's engine, I noticed the unit wouldn't turn on. No matter how times I attempted to reset it, it wouldn't do anything (although when doing so, through the small pin hole, colorful led light would cycle through the cover.
I contacted Wondefoo and they sent-me a an HTC-PX5--REV12(LPDDR-221), 20190515, board replacement, exactly like the original one. After replacing it, the unit started working again.
In january 2020 this happened again. Tried exchanging it again with the original MCU; nothing worked.
Nearly two months later I attempted the same procedura and this time it worked - the unit started working again.
My bet is that something is causing this unit to get stuck, and after enough time passes and the capacitors get emptied and the DRAM erases, it's able to "recover" somehow.
Maybe 6 months ago, this happened again. Out of frustration, in the middle of a drive, once I started pushing all the buttons randomly. Finally, I don't know by which combination, the unit turned on, displaying a recover menu. I don't know how, simple choosed to restart and it became working again.
Some weeks later, after getting unresponsive again and trying the "random button push" procedure, the menu showed up again. This time I attempted a factory reset and got the unit working for severl weeks.
Finally, my unit died for the last time about two months ago and I haven't been able to recover it by the "pushing buttons" method, neither by disconnecting it from the power source and reconnecting days later. I came back to the original radio player, which is a hassle as the CD player is also broken.
I'd like to try echanging the MCU with the spare one; I'm almost sure that it will work again, but before doing so I'd like to assure that I won't find myself in this situation again, as it's a waste of time. Maybe the problem is known and you can recommend me a software version / update that would prevent this from happen again. Maybe there is some sort of hardware mod that can be attempted by replacing some component. Maybe you know how to "hard reset" it from some motherboard pins, maybe where I could mount a switch to do so when the unit becomes dead, or maybe you can tell me the proper key combination for the recovery menu.
I've also found some firmware pages, namely https://yadi.sk/d/umCvHqCDzHccr, with a long list for several models. It looks more or less clear where to get the MCU firmware, but for the Android image it's a bit more complicated. If I enter the RockChip PX5 Android 9 folder, then HTC subfolder, there are several HTC4_XXXXXXXXXXX, HTC5_XXXXXXXXXXX and HTC_XXXXXXXXXXX options, and the same for RockChip PX5 Android 10 (assuming that there were an Android 10 update for my hardware; it came with Android 9 if I'm not wrong), so I don't know which one to attempt.
PS: the "reset" little hole never has really worked for me in this situation. It just will cycle to RGB leds if I push it with a paperclick and, while pushing, press the "on" button, and they will shut off when I release the button, but that's all.
Noone encountered a similar problem?
I recently tried to update the MCU in my Dasaita PX6 head unit. After the update the unit is entirely unresponsive. I looked at the MCU file after I installed it and realized I installed the MCU from another company, not Dasaita. (I realize I should have cheeked this before but I did not and is why I'm in this situation now. Is there anything I can do to fix it? I tried to enter recovery mode, however, the reset button does not work. The screen remains black and the buttons do not light up like they did before the update when the reset button was pressed. Fuses are in good condition. My exact unit is linked here: https://www.amazon.com/Dasaita-Android-Corolla-2014-2017-Carplay/dp/B07XQJH6V6 .
Runnitech said:
I recently tried to update the MCU in my Dasaita PX6 head unit. After the update the unit is entirely unresponsive. I looked at the MCU file after I installed it and realized I installed the MCU from another company, not Dasaita. (I realize I should have cheeked this before but I did not and is why I'm in this situation now. Is there anything I can do to fix it? I tried to enter recovery mode, however, the reset button does not work. The screen remains black and the buttons do not light up like they did before the update when the reset button was pressed. Fuses are in good condition. My exact unit is linked here: https://www.amazon.com/Dasaita-Android-Corolla-2014-2017-Carplay/dp/B07XQJH6V6
Click to expand...
Click to collapse
hi friend i am in same situation, but difference is that i have white screen and do not know what to do.
anybody can help?
saady002000 said:
hi friend i am in same situation, but difference is that i have white screen and do not know what to do.
anybody can help?
Click to expand...
Click to collapse
Hi guys i am in same situation with same Dasaita max10 px6 unit and have only white screen.
I need help to get back to factory settings or add new rom.
If anybody solved please share in details how.