Android Froyo, HTC Desire HD with Navigon Mobile Navigator.
I can connect the phone to my car stereo through Bluetooth. Everything works fine. I can receive and make calls and music routed through to Bluetooth perfectly. When I use Mobile Navigator the turn-by-turn instructions come through the phone speaker, then a second later they also come through the bluetooth connection to the car. The beginning of the bluetooth instruction is also cut off. I can't find anywhere to explicitly disable the phone speaker when audio is routed to Bluetooth, although other apps don't seem to suffer from this. Anyone know a hack?
Same Problem here. sound is routed through bluetooth and phone speaker while bluetooth is cut off. I assume the Navigon software has a bug here. I hope they fix it soon
unfortunately I did not find any workarround or fix till now
anyone?
I had a workaround using car UI by beemer. Unfortunately after upgrading to android 2.2.1 I can't make it work anymore but am not sure where the problem lies as even downgrading again through backup-restore left the same problem. I'd be interested to hear if anyone has a magic trick for producing the right combination of settings as I know this was working before with a 2.2.0 based rom and car UI.
I'm having an issue with my Bluetooth and am wondering if anyone else is having the same issue. For some reason, when I have my car connected via Bluetooth for audio/calls and I connect to GPS (using Garmin or VZ navigator, for example), the Bluetooth fully disconnects. I can have the car reconnect just fine, but if I leave the navigation open, the Bluetooth will disconnect again almost immediately. I know this isn't an issue with my car, as I've had other phones that don't have the issue.
At this point I'm not sure if it's a hardware or software issue. I have the Verizon 8x. Is anyone else having this problem?
Hi, hope someone can help with this.
I just installed the new PA79DLRIPL into my car which went fairly smoothly, however I'm having some issues with it.
Like others in this thread, I am unable to get the AUX bypass working, currently the sound is not going through to the speakers from the Xtrons unit. I also noticed that the rear AUX input is now also not working either, which I'm hoping is due to the adaptor that is trying to bypass it?
Also my GPS signal is basically useless in this thing, is there something I can do to improve it? It takes a while to connect to any satellite and even once it does, the connections are poor based on the GPS status screen in the settings and the speed/location data is inaccurate. I've attached the antenna to top of the middle speaker grill (no speaker installed there) so it's as close to the top as can be without being exposed. Is there a location setting I need to change or is it just a bad antenna?
Thanks for any help!
What did the reseller suggest when approached for support? What have you tried?
Hi
I have purchased an Android HeadUnit for my Renault Megane 2 (2007) from AliExpress. Every function works except the steering wheel controls. The unit has the UIS7862 CPU @1.8Ghz, 6gb Ram and 128gb storage. I have installed the CanBox correctly and tried many CanBox settings in factory menu, but I cannot get the control app to enter learning mode. Does anyone have any idea? Maybe the built in key map application is at fault (com.syu.steer).
Did you find a solution to your problem yet?
I'm stuck at the exact same scenario, same unit. The support over at AliExpress mention to me to select "XP" for canbox settings. However, my canbus module is by Raise, hence I should be using the "RZC"
Also, my reverse cam doesnt work too.
Pls share your findings. Thank you!
I got the steering wheel keys to work with a custom controller made by an engineer in my country specifically for my car and my HeadUnit. The controller is connected directly to the wheel controls and the "key" wire on my HeadUnit. I had to disassembly the steering wheel base and route the cable around the original one. Now I can map every key to an action in the Key Learning app. For the backup camera, because I used a wireless kit, I couldn't use the "back" camera wire to trigger the HeadUnit to switch to it. The kit came with a receiver which only had power wires and a yellow RCA cable. I wired the receiver's power cables to the ACC power so that the receiver only powers on when the engine is running and I managed to map a button on the steering wheel to switch to the RCA input. Now when I want to use back up camera, I just need to press a button to see the image. The camera's transmitter is wired to the license plate bulb and I managed to fit it in the rear bumper.
This wasn't a "plug and play" experience that the Chinese seller promised, but overall I can say I am pretty happy with the end result. The audio quality is wayyy better than the stock HeadUnit. I didn't know that my stock speakers could get that loud and have so much bass. The DSP chip does it's job wonderfully. Also the radio reception is better than with the stock unit. The Android HeadUnit is fast and snappy. Apps open almost instantly and those 6gb of ram really help. I could compare the overall user experience with my OnePlus 7 phone. The unit also cold boots very quickly. The wifi reception is pretty poor. The unit shows 75% signal when my phone is in the car. It doesn't bother me because I put a Sim card in the unit and the mobile reception is as good as on my phone.
andrei-2200 said:
I got the steering wheel keys to work with a custom controller made by an engineer in my country specifically for my car and my HeadUnit. The controller is connected directly to the wheel controls and the "key" wire on my HeadUnit. I had to disassembly the steering wheel base and route the cable around the original one. Now I can map every key to an action in the Key Learning app. For the backup camera, because I used a wireless kit, I couldn't use the "back" camera wire to trigger the HeadUnit to switch to it. The kit came with a receiver which only had power wires and a yellow RCA cable. I wired the receiver's power cables to the ACC power so that the receiver only powers on when the engine is running and I managed to map a button on the steering wheel to switch to the RCA input. Now when I want to use back up camera, I just need to press a button to see the image. The camera's transmitter is wired to the license plate bulb and I managed to fit it in the rear bumper.
This wasn't a "plug and play" experience that the Chinese seller promised, but overall I can say I am pretty happy with the end result. The audio quality is wayyy better than the stock HeadUnit. I didn't know that my stock speakers could get that loud and have so much bass. The DSP chip does it's job wonderfully. Also the radio reception is better than with the stock unit. The Android HeadUnit is fast and snappy. Apps open almost instantly and those 6gb of ram really help. I could compare the overall user experience with my OnePlus 7 phone. The unit also cold boots very quickly. The wifi reception is pretty poor. The unit shows 75% signal when my phone is in the car. It doesn't bother me because I put a Sim card in the unit and the mobile reception is as good as on my phone.
Click to expand...
Click to collapse
Thank you for explaining your solution. Seems like quite a bit of work.
I managed to get my steering controls working finally. Got the correct canbus setting and corrected a connection.
Now, I'm stull stuck with the reverse cam issue. The +12V does energize when I am in reverse gear - I tested this when I connected my cam to DV-in and cam turns on only when in reverse.
But I just don't understand why the Android won't switch to Cam in during reverse gear.
Will continue to seek help from the manufacturer. Otherwise, it's a great HU as you said. Awesome speed!
MasK said:
Thank you for explaining your solution. Seems like quite a bit of work.
I managed to get my steering controls working finally. Got the correct canbus setting and corrected a connection.
Now, I'm stull stuck with the reverse cam issue. The +12V does energize when I am in reverse gear - I tested this when I connected my cam to DV-in and cam turns on only when in reverse.
But I just don't understand why the Android won't switch to Cam in during reverse gear.
Will continue to seek help from the manufacturer. Otherwise, it's a great HU as you said. Awesome speed!
Click to expand...
Click to collapse
You connected the reverse wire?
Maybe this triggers the camera view of it doesn't work via the canbus.
Well, it does work via canbus, just doesnt switch to cam input automatically. Perhaps its some software settings.
MasK said:
Well, it does work via canbus, just doesnt switch to cam input automatically. Perhaps its some software settings.
Click to expand...
Click to collapse
Not all canbus provide the reverse signal. So maybe you have to provide the reverse signal on the separate input.
TorstenH said:
Not all canbus provide the reverse signal. So maybe you have to provide the reverse signal on the separate input.
Click to expand...
Click to collapse
I feel that the HU knows when I am referring (CANBUS might be working here), because the 12V turns on when Im in reverse. The only issue is the HU doesnt switch to the cam automatically. Looks to me like a SW issue. Still awaiting reply from manufacturer.
Also, I realised my backward/forward buttons are swapped. Why is it I can't re-learn them?
It may not be the same for the Navifly, but on my unit, G5 must get the proper voltage to "detect" the car has been put in reverse. I'm re-using my factory rear view camera and it's a 6.5V camera. However, I had to up the voltage to 8.6V so that G5 go that voltage...then the rear image showed up. I reused the car wiring and that's why I had to do this.
Check the voltage that G5 is getting. With a canbus module, I believe there is a wire from the canbus going to G5. If no voltage, make sure the pins are in properly.
FYI, if you are using a canbus and the steering wheel controls go through the canbus, then I believe that you cannot remap the keys.
The 12 V from the reverse wire are coming from your car (or in some cases from the canbox if the information gets transmitted from car to the box via canbus).
My suggestion is:
There is a separate reverse connection (usually a brown wire) on the head unit which triggers the radio to open the app which shows the image of the reverse cam.
You could even connect ACC or B+ to the reverse connection for testing purposes.
mastrv said:
It may not be the same for the Navifly, but on my unit, G5 must get the proper voltage to "detect" the car has been put in reverse. I'm re-using my factory rear view camera and it's a 6.5V camera. However, I had to up the voltage to 8.6V so that G5 go that voltage...then the rear image showed up. I reused the car wiring and that's why I had to do this.
Check the voltage that G5 is getting. With a canbus module, I believe there is a wire from the canbus going to G5. If no voltage, make sure the pins are in properly.
FYI, if you are using a canbus and the steering wheel controls go through the canbus, then I believe that you cannot remap the keys.
Click to expand...
Click to collapse
Absolutely correct.
Thanks guys, but there is no other brown wire for this.
I have a discussion abt this on this thread too:
Medeke/Navifly 7862
Hi, Recently received above unit for my 2006 RS4. everything is great (much better then the M400 I had before) apart from the radio. It seemed to work for the first 2 days, then worked intermittently and now not at all. I have tried...
forum.xda-developers.com
My "cam12V" wire is from the HU and it turns on when I am in reverse. Does this mean that this signal might be coming from my canbus? If so, is there another input back to the HU to trigger the screen to display the video feed? Only other wires I see are AMP related
Give 12V to pin 2 and check if the app to display the image of the cam will start:
TorstenH said:
Give 12V to pin 2 and check if the app to display the image of the cam will start:
View attachment 5374441
Click to expand...
Click to collapse
Yes! It took me a while to figure this out.. mainly because I'll have to cut the wire (wasn't very confident in that)
and also.. the wires at Pin2 didn't make sense! They were more like Battery12V. I did cut and tested that.
So.. it turns out its a pink wire at pin3!
I realized this as I looked at my old Dasaita wires from the canbus connector. Since canbus is a standard, they should be comparable. That reverse wire went into Pin3.
I'm really surprised that Mekede and Navifly has this pin layout printed in all their listings.. but it's just wrong.
Thanks alot for the help!
That means it works now? I think you had to cut the ACC wire according to the manual because the "ignition on" information is provided by the can box.
TorstenH said:
That means it works now? I think you had to cut the ACC wire according to the manual because the "ignition on" information is provided by the can box.
Click to expand...
Click to collapse
Yes it works now. Check out the images. The Pin2 (red) is probably ACC or batt 12V as there was no power when cut. I then cut the wire opposite it (pin10) in case I was looking at the connector wrongly. That turned out to be the headlight sensor.
After tracing the wire and comparing to my old Daisata, it turns out Pin3 (pink) is the reverse IN.
Excellent. Thanks for the clarification.
That means it makes sense to get the wiring diagram from the old radio of the car and compare it with the description of the new head unit.
In my case I had to completely rewire the harness (just if someone is interested):
Junsun V1 MTK8259 - the adapter battle (Kia Ceed Jd) / OEM camera usage / reference thread
I bought the Junsun V1 head unit but my Kia Ceed JD had a OEM nav unit which isn't directly compatible to Junsun V1. So I re-wired the wiring harness based on the pins description of my original OEM navigation unit. I'm only modifying the wiring...
forum.xda-developers.com
The only thing that I could compare to (between old and new HUs) is the canbus connectors. Rest cannot be compared as they're all different.
Oh well..
Anyways, the current Mekede I have has Radio chip NX6686. My old Dasaita PX5 also has a NX6686. However, the radio reception is absolutely trash in the new one. I dont listen to radio that often (I can resort to streaming radio) but my dad takes the car occasionally and he's already complained about it
Your experience on the harness rewiring is pretty intense!
Update: Turns out my Antenna connector was a tad loose and I had to do a re-connect. The radio reception is all good now
MasK said:
Thank you for explaining your solution. Seems like quite a bit of work.
I managed to get my steering controls working finally. Got the correct canbus setting and corrected a connection.
Now, I'm stull stuck with the reverse cam issue. The +12V does energize when I am in reverse gear - I tested this when I connected my cam to DV-in and cam turns on only when in reverse.
But I just don't understand why the Android won't switch to Cam in during reverse gear.
Will continue to seek help from the manufacturer. Otherwise, it's a great HU as you said. Awesome speed!
Click to expand...
Click to collapse
So you found correct canbus settings and connections .. i cant find anything about you sharing them