Related
Solve it.
boot into recovery and flash the rom again or factory reset
Solve.
Oh my lord. Finally i'd done it by myself. Now my phone live back!!! Anyway, thanks for the help man. I appreciated it. =)
henrylhp said:
Oh my lord. Finally i'd done it by myself. Now my phone live back!!! Anyway, thanks for the help man. I appreciated it. =)
Click to expand...
Click to collapse
Share the solution?) It's always interesting!
Oh, hmm, i can't start my phone before because i follow a guide that teach how to upgrade firmware, and download file with it, but it teached me to click at the Re-partition, and the firmware file that he ask me to download, got problem. So, after i follow what he teached, and my upgrade failed. That's make my phone can't boot or works. AFter that i keep on searching and searching, and found that i don't have "cache" or others setting inside my phone, and that's all are inside the" PIT" file, so i download a PIT file, and install it with Odin, by put it in the "PIT" setting, but don't click at the Re-partition. Haha, now, my phone live back. =) Of course, i download others firmware version too, and install it again.
PIT file?
henrylhp said:
Oh, hmm, i can't start my phone before because i follow a guide that teach how to upgrade firmware, and download file with it, but it teached me to click at the Re-partition, and the firmware file that he ask me to download, got problem. So, after i follow what he teached, and my upgrade failed. That's make my phone can't boot or works. AFter that i keep on searching and searching, and found that i don't have "cache" or others setting inside my phone, and that's all are inside the" PIT" file, so i download a PIT file, and install it with Odin, by put it in the "PIT" setting, but don't click at the Re-partition. Haha, now, my phone live back. =) Of course, i download others firmware version too, and install it again.
Click to expand...
Click to collapse
Where did you get the PIT file?
Okay i have a question about the T959v. Here are the facts: Phone was flashed with ODIN but the repartition box was checked. It was my fault because i didn't double check before flashing. Now the phone is in a recovery bootloop when i try to turn it on. I can reach DOWNLOAD MODE but then again if i try to flash it again same thing will happen. Is there something i can do or is the phone bricked because of that???? Thanks in advance!
What's the rom you are flashing?
Sent from my SGH-T959V using xda premium
Stock kd1 but i have some other roms like gingerbread...
Im using the .831 pit file also, but i have tried without the pit file and nothing. Also tried without repartition checked but it will do the same thing. Problem is that first time i flashed i had repartition checked
enelyam said:
Im using the .831 pit file also, but i have tried without the pit file and nothing. Also tried without repartition checked but it will do the same thing. Problem is that first time i flashed i had repartition checked
Click to expand...
Click to collapse
And your sure the rom is for the sgs4g and not the vibrant, right? Because the two are majorly different...
Sent from my SGH-T959V using XDA App
Yes i am, like i said the mistake i made was leaving the repartition option checked. For some reason the phone has a boot loop and when i hit reboot now on recovery it says failed to mount /data invalid argument. Never had something like this happened before and i have flash a ton on galaxys
enelyam said:
Im using the .831 pit file also, but i have tried without the pit file and nothing. Also tried without repartition checked but it will do the same thing. Problem is that first time i flashed i had repartition checked
Click to expand...
Click to collapse
I think Odin will auto re partition when you flash the pit. You can un check it and it should be fine either way.
enelyam said:
Yes i am, like i said the mistake i made was leaving the repartition option checked. For some reason the phone has a boot loop and when i hit reboot now on recovery it says failed to mount /data invalid argument. Never had something like this happened before and i have flash a ton on galaxys
Click to expand...
Click to collapse
I may be wrong but...
I think you need the csc. If your just flashing the pit and pda your missing the other partitions. I think when you repartitioned it wiped the partitions and you are missing one or more.
enelyam said:
Yes i am, like i said the mistake i made was leaving the repartition option checked. For some reason the phone has a boot loop and when i hit reboot now on recovery it says failed to mount /data invalid argument. Never had something like this happened before and i have flash a ton on galaxys
Click to expand...
Click to collapse
I had the same problem that you are experiencing. The fix for me was to get a full Factory load that was verified to be for the GalaxyS4G. Which is the model number that you listed. The Odin that I loaded is T595VUVKF1. This requires that you load each file in the proper Odin category. Use the Pit file, PDA, Phone and CSC files. Leave the repartition box checked and you should get your stock image back, from there you can install CWM and flash another image.
Allright thanks a lot! I knew something like that was happening but i have not been able to find a firmware with those files divided i mean the csc,pda, and phone files separated. Everything i found has been the package that you just file in pda... If anybody know where to find that i appreciate the link.
enelyam said:
Allright thanks a lot! I knew something like that was happening but i have not been able to find a firmware with those files divided i mean the csc,pda, and phone files separated. Everything i found has been the package that you just file in pda... If anybody know where to find that i appreciate the link.
Click to expand...
Click to collapse
I think this package should help you out...
http://forum.xda-developers.com/showthread.php?t=1183413&highlight=odin+kg4
If not, I have one that has all 3 necessary files that (just not the pit which you already have anyways) I can upload and share that will get you going again...
enelyam said:
Allright thanks a lot! I knew something like that was happening but i have not been able to find a firmware with those files divided i mean the csc,pda, and phone files separated. Everything i found has been the package that you just file in pda... If anybody know where to find that i appreciate the link.
Click to expand...
Click to collapse
Just get a heimdall one click. It has everything you need in one tiny easy to use package.
It's ok guys! And thanks for the inputs. I found what i was looking for and flashed the phone. It working like a charm! with KF1 thanks a lot
enelyam said:
It's ok guys! And thanks for the inputs. I found what i was looking for and flashed the phone. It working like a charm! with KF1 thanks a lot
Click to expand...
Click to collapse
Sweet, glad you got it working but i recommend you do it again with kj6 official GB. kf1 was the first GB leak we got. It has a borked boot loader file so good luck with recovery and download mode
Bassmanjames said:
Sweet, glad you got it working but i recommend you do it again with kj6 official GB. kf1 was the first GB leak we got. It has a borked boot loader file so good luck with recovery and download mode
Click to expand...
Click to collapse
Congrats man...
+1 on the KJ6...
So I installed new ICS leak using I727UCALC4_OneClick and was running fine but all of a sudden lock screen stop working. I reset the phone and ran it again and phone now freezes up every 5 mins. How do I get back to 2.3.5 UCKJ2? I already tried using Odin and flashing stockrecovery.tar and no luck still stuck on ICS. I downloaded SGG-I727-UCKJ2-k0kane.7z and also SGH-I727UCKJ2_I727ATTKJ2.rar but when I go into dl mode computer can't recognize these two files or just can't find them. I need help please, thanks in advance.
Envy Diz said:
So I installed new ICS leak using I727UCALC4_OneClick and was running fine but all of a sudden lock screen stop working. I reset the phone and ran it again and phone now freezes up every 5 mins. How do I get back to 2.3.5 UCKJ2? I already tried using Odin and flashing stockrecovery.tar and no luck still stuck on ICS. I downloaded SGG-I727-UCKJ2-k0kane.7z and also SGH-I727UCKJ2_I727ATTKJ2.rar but when I go into dl mode computer can't recognize these two files or just can't find them. I need help please, thanks in advance.
Click to expand...
Click to collapse
You probably need to unzip the .7z and .rar file to use them. I believe Odin only "sees" .tar files.
Make sure you read the instructions carefully and know what you're doing.
Envy Diz said:
So I installed new ICS leak using I727UCALC4_OneClick and was running fine but all of a sudden lock screen stop working. I reset the phone and ran it again and phone now freezes up every 5 mins. How do I get back to 2.3.5 UCKJ2? I already tried using Odin and flashing stockrecovery.tar and no luck still stuck on ICS. I downloaded SGG-I727-UCKJ2-k0kane.7z and also SGH-I727UCKJ2_I727ATTKJ2.rar but when I go into dl mode computer can't recognize these two files or just can't find them. I need help please, thanks in advance.
Click to expand...
Click to collapse
K0nane's thread should work for you if you read and follow the directions.
SamMobile.com also has original Skyrocket firmware that flashes via Odin. The SamMobile version is a more complete install that is reported to not trip the counter and show as "original Samsung firmware". I havn't tried either version so you need to read for yourself before you ask any questions or try anything.
projeqht said:
You probably need to unzip the .7z and .rar file to use them. I believe Odin only "sees" .tar files.
Make sure you read the instructions carefully and know what you're doing.
Click to expand...
Click to collapse
Impossible to unzip because its a .7z and .rar file, computer won't let me I tried it already.
scott14719 said:
K0nane's thread should work for you if you read and follow the directions.
SamMobile.com also has original Skyrocket firmware that flashes via Odin. The SamMobile version is a more complete install that is reported to not trip the counter and show as "original Samsung firmware". I havn't tried either version so you need to read for yourself before you ask any questions or try anything.
Click to expand...
Click to collapse
It's not working Odin can't find files.
Envy Diz said:
It's not working Odin can't find files.
Click to expand...
Click to collapse
ODIN doesn't look for files. You need to tell them where there are by clicking on PDA and choosing the tar from wherever location you saved it.
dicksteele said:
ODIN doesn't look for files. You need to tell them where there are by clicking on PDA and choosing the tar from wherever location you saved it.
Click to expand...
Click to collapse
lol I know that but it's not there trust me.
Envy Diz said:
Impossible to unzip because its a .7z and .rar file, computer won't let me I tried it already.
Click to expand...
Click to collapse
I unzipped it, you have to or it won't do ****
Sent from SKYROCKET
NexusMod 4.0
Romracer 0.3
Envy Diz said:
lol I know that but it's not there trust me.
Click to expand...
Click to collapse
You need to unzip the files with an extractor. It has to be a .tar file to get Odin to see it. Plain and simple.
Envy Diz said:
Impossible to unzip because its a .7z and .rar file, computer won't let me I tried it already.
Click to expand...
Click to collapse
Yeah since its a .7z and .rar file, you'll need to download WinRar or 7zip to unzip them.
Winzip probably won't suffice. Good luck.
File was corrupted not sure why, now in dl mode I get error message that says Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again. I'm dl another one now and will unzip to see if that works, I'm crossing my fingers. Thanks
It worked but baseband isn't UCKJ2 and I keep getting foreclose message that google services isn't working :/ baseband is I727UCALC4
Envy Diz said:
It worked but baseband isn't UCKJ2 and I keep getting foreclose message that google services isn't working :/ baseband is I727UCALC4
Click to expand...
Click to collapse
The knonane tar does not include radio
xcrazydx said:
The knonane tar does not include radio
Click to expand...
Click to collapse
Can't seem to find radio that is flashable through Odin, also noticed counter was set off.
Envy Diz said:
Can't seem to find radio that is flashable through Odin, also noticed counter was set off.
Click to expand...
Click to collapse
Yes, of course. Did you read about this before doing it? You can get the full tar with radio from sammobile and it wont set off the counter.
xcrazydx said:
Yes, of course. Did you read about this before doing it? You can get the full tar with radio from sammobile and it wont set off the counter.
Click to expand...
Click to collapse
This one I727UCKJ2_I727ATTKJ2_ATT.zip? Still doesn't have radios I'm looking for I tried that one first.
Envy Diz said:
This one I727UCKJ2_I727ATTKJ2_ATT.zip? Still doesn't have radios I'm looking for I tried that one first.
Click to expand...
Click to collapse
What radio do you want? thats stock att
Envy Diz said:
File was corrupted not sure why, now in dl mode I get error message that says Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again. I'm dl another one now and will unzip to see if that works, I'm crossing my fingers. Thanks
Click to expand...
Click to collapse
Envy Diz said:
It worked but baseband isn't UCKJ2 and I keep getting foreclose message that google services isn't working :/ baseband is I727UCALC4
Click to expand...
Click to collapse
Envy Diz said:
Can't seem to find radio that is flashable through Odin, also noticed counter was set off.
Click to expand...
Click to collapse
I strongly suggest you completely stop what you are doing and actually do a little research and reading before you go any further. Every issue you have encountered has been identified many times and is always caused from people not taking the time to learn about what they are doing for they jump right in. YOU WILL END UP WITH A BRICKED PHONE IF YOU CONTINUE WITHOUT READING AND RESEARCHING!
The Kies message was brought up several times today in other threads relating to this ICS leak. You need to read all of the threads related to it.
I mentioned the counter in this very thread...if you would have read it. The baseband (radio) isn't flashed with K0nane's TAR or most other ROMS (unless otherwise stated). You have to go to the "Radio" thread in the DEV section and flash it through CWM seperately. It has been reported (by others) that the firmware at SamMobile WILL flash the correct modem and (I'll say it again) will not trigger the counter.
DO what you want, its your phone, but if you aren't going to take the time to learn about what you are doing you will be the owner of a bricked phone.
scott14719 said:
I strongly suggest you completely stop what you are doing and actually do a little research and reading before you go any further. Every issue you have encountered has been identified many times and is always caused from people not taking the time to learn about what they are doing for they jump right in. YOU WILL END UP WITHA BRICKED PHONE IF YOU CONTINUE WITHOUT READING AND RESEARCHING!
The Kies message was brought up several times today in other threads relating to this ICS leak. You need to read all of the threads related to it.
I mentioned the counter in this very thread...if you would have read it. The baseband (radio) isn't flashed with K0nane's TAR or most other ROMS (unless otherwise satated). You have to go to the "Radio" thread in the DEV section and flash it through CWM seperately. It has been reported (by others) that the firmware at SamMobile WILL flash the correct modem and (I'll say it again) will not trigger the counter.
DO what you want, its your phone, but if you aren't going to take the time to learn about what you are doing you will be the owner of a bricked phone.
Click to expand...
Click to collapse
Very good advice sir! I recommend this also, envy
scott14719 said:
I strongly suggest you completely stop what you are doing and actually do a little research and reading before you go any further. Every issue you have encountered has been identified many times and is always caused from people not taking the time to learn about what they are doing for they jump right in. YOU WILL END UP WITHA BRICKED PHONE IF YOU CONTINUE WITHOUT READING AND RESEARCHING!
The Kies message was brought up several times today in other threads relating to this ICS leak. You need to read all of the threads related to it.
I mentioned the counter in this very thread...if you would have read it. The baseband (radio) isn't flashed with K0nane's TAR or most other ROMS (unless otherwise satated). You have to go to the "Radio" thread in the DEV section and flash it through CWM seperately. It has been reported (by others) that the firmware at SamMobile WILL flash the correct modem and (I'll say it again) will not trigger the counter.
DO what you want, its your phone, but if you aren't going to take the time to learn about what you are doing you will be the owner of a bricked phone.
Click to expand...
Click to collapse
Did read but there's way to much lol ...see with S2 everything was packed in one file, easy flash through Odin and you were set...But thanks for the info.
Sent from my SAMSUNG-SGH-I727 using xda premium
Sprint s6 edge it was boot looping only staying in Android for maybe 3-5 mins at a time. So i tried to flash it. I may have flashed 5.0.x to it. Now when I try to flash I can flash cm.bin, sboot and it always dies on boot.img. I really need some guidance on what i should try next.
Looking around shows boot.img not flashing is possibly the kernel but I am having trouble finding one that it will let me flash.
peterm20 said:
Sprint s6 edge it was boot looping only staying in Android for maybe 3-5 mins at a time. So i tried to flash it. I may have flashed 5.0.x to it. Now when I try to flash I can flash cm.bin, sboot and it always dies on boot.img. I really need some guidance on what i should try next.
Looking around shows boot.img not flashing is possibly the kernel but I am having trouble finding one that it will let me flash.
Click to expand...
Click to collapse
Were you originally on 5.1.1?
If so, are you having a hard time Odin-ing the stock rom?
Robbie Doo said:
Were you originally on 5.1.1?
If so, are you having a hard time Odin-ing the stock rom?
Click to expand...
Click to collapse
yes, it is a phone of a friend though I was trying to repair it. I downloaded the 5.1.1 from that slow sammoble site.
peterm20 said:
yes, it is a phone of a friend though I was trying to repair it. I downloaded the 5.1.1 from that slow sammoble site.
Click to expand...
Click to collapse
Since you were on 5.1.1 I don't think you would have any trouble Odining the stock ROM onto the phone. I've done it a few times and it worked OK. After you push the stock ROM you can root it if you want to.
Robbie Doo said:
Since you were on 5.1.1 I don't think you would have any trouble Odining the stock ROM onto the phone. I've done it a few times and it worked OK. After you push the stock ROM you can root it if you want to.
Click to expand...
Click to collapse
Well the problem is it won't flash past boot.img
As soon as boot.img is started it goes a green bar on Oden about 3/4 of the way and then goes FAILED! and oden disconnects the device.
peterm20 said:
Well the problem is it won't flash past boot.img
As soon as boot.img is started it goes a green bar on Oden about 3/4 of the way and then goes FAILED! and oden disconnects the device.
Click to expand...
Click to collapse
If you went from 5.1.1 to 5.0.X it's most likely hard bricked.
Soooperstar said:
If you went from 5.1.1 to 5.0.X it's most likely hard bricked.
Click to expand...
Click to collapse
Even if i can get in to download mode?
peterm20 said:
Even if i can get in to download mode?
Click to expand...
Click to collapse
Yea.... You have to stay within the same android version, ex. Any of the 5.1.1 updates. The firmware version that you're trying to restore with, is it OF7?
Soooperstar said:
Yea.... You have to stay within the same android version, ex. Any of the 5.1.1 updates. The firmware version that you're trying to restore with, is it OF7?
Click to expand...
Click to collapse
I think it is OF7.
peterm20 said:
I think it is OF7.
Click to expand...
Click to collapse
It should say it on the tar file. It's worth a try but you're probably dead. Here is the file if you need it but like I said, most likely you're done.
http://forum.xda-developers.com/showthread.php?t=3154757
peterm20 said:
Well the problem is it won't flash past boot.img
As soon as boot.img is started it goes a green bar on Oden about 3/4 of the way and then goes FAILED! and oden disconnects the device.
Click to expand...
Click to collapse
Which version of the Odin are you using?
Soooperstar said:
It should say it on the tar file. It's worth a try but you're probably dead. Here is the file if you need it but like I said, most likely you're done.
http://forum.xda-developers.com/showthread.php?t=3154757
Click to expand...
Click to collapse
It worked for me. I have a friend who did the same thing and thought the phone was a gonner. I told her I'd give it a try and I was able to Odin (v.3.10.6) to OF7, took the OTA to OH1 and flashed Wicked One SS v.3.0 from @dazednconfused and she says it's running perfect.
Also, @Soooperstar Odin file here.
JediMindTrixx said:
It worked for me. I have a friend who did the same thing and thought the phone was a gonner. I told her I'd give it a try and I was able to Odin (v.3.10.6) to OF7, took the OTA to OH1 and flashed Wicked One SS v.3.0 from @dazednconfused and she says it's running perfect.
Also, @Soooperstar Odin file here.
Click to expand...
Click to collapse
Your friend went from 5.1.1 to 5.0.X? That's the link I just gave him
Yes she did. Sorry about that, saw that afterwards.
Sent from a Galaxy S6 Edge... Far, Far, Away...
JediMindTrixx said:
Yes she did. Sorry about that, saw that afterwards.
Sent from a Galaxy S6 Edge... Far, Far, Away...
Click to expand...
Click to collapse
Interesting
Robbie Doo said:
Which version of the Odin are you using?
Click to expand...
Click to collapse
the latest one. I've seen various other flashing posts saying you should use a slightly older Oden.
Also side rant. I did a chat with samsung support and they said the Smart Switch recovery doesn't work with the S6? I cannot get it to verify the serial number of my phone (s6) and the broken one (s6 e)
peterm20 said:
the latest one. I've seen various other flashing posts saying you should use a slightly older Oden.
Also side rant. I did a chat with samsung support and they said the Smart Switch recovery doesn't work with the S6? I cannot get it to verify the serial number of my phone (s6) and the broken one (s6 e)
Click to expand...
Click to collapse
3.10.6 is what I use
peterm20 said:
the latest one. I've seen various other flashing posts saying you should use a slightly older Oden.
Also side rant. I did a chat with samsung support and they said the Smart Switch recovery doesn't work with the S6? I cannot get it to verify the serial number of my phone (s6) and the broken one (s6 e)
Click to expand...
Click to collapse
I'm not sure which version you are referring to as the latest one, but the only version that will work with what you're trying to accomplish is 3.10.6
Soooperstar said:
It should say it on the tar file. It's worth a try but you're probably dead. Here is the file if you need it but like I said, most likely you're done.
http://forum.xda-developers.com/showthread.php?t=3154757
Click to expand...
Click to collapse
Well your file got me way further than I've got before. I can get it to write the system.img in "BL" but if i use AP it fails about 1/2 the way through
peterm20 said:
Well your file got me way further than I've got before. I can get it to write the system.img in "BL" but if i use AP it fails about 1/2 the way through
Click to expand...
Click to collapse
Like I said from my knowledge, you should be hard bricked, but if someone else went from 5.1.1 to 5.0.X and back, you might want to find out what they did. Don't think it's possible
as the title suggests, I'm trying to find binary 7(u7) combination rom for samsung galaxy s8+(sm-g955w):good:
No free download at this moment.
Needs some kindness man who have Premium account to download for us
https://easy-firmware.com/index.php?a=downloads&b=tags&tag=G955USQU7ASK1
OR
https://firmwarex.net/samsung-s8-sm-g955u-combination-file-factory_sw-2/
sm-g955w binary 7 combination firmware
ahh yes, that's the website I seen the u7 binary on. I was trying to find it again. But yes if someone who has a premium account on easy firmware to help get the file.:angel:
http://www.gsm2file.com/index.php?f...3_REV00_user_mid_noship_MULTI_CERT.tar.md5.7z
this one may be the cheapest.But we don't have PayPal in my country
I found another website that has the file, https://www.fullstockfirmwaredownload.com/sm-g955w/
only 2 dollars USD but I do not have a credit card...
It's not COMBINATION file ,it is only full stock firmware
oh yeah, woooopsie
Ok, I paid for the file and it's downloading right now. I'll upload it for you in a bit when it finishes downloading ok.
Thank you. It's very kind of you
http://nitroflare.com/view/FE27819B...3_REV00_user_mid_noship_MULTI_CERT.tar.md5.7z
Excuse me,DO you have Google drive download link?The download speed is too slow in China . Thank you very much
FalsAlarm said:
http://nitroflare.com/view/FE27819B...3_REV00_user_mid_noship_MULTI_CERT.tar.md5.7z[/QUOTE
At last I downloaded successfully. Thank you again
Click to expand...
Click to collapse
what do I do after flashing combination firmware in order to remove FRP lock?
Have you flashed the combination ?if yes just go into setting and find factory reset,reset the phone, then flash full stock firmware. The fpr lock will gone
If you haven't flashed the combination, you'd better unzip it and remove the tz.mbn file,and then package it using 7z file .After doing this you can flash it . The tz.mbn file have much chance will make your phone softbrick.It very important
yes, factory reset worked, thanks
Does this help https://forum.xda-developers.com/s1...a-samsung-firmware-downloader-t3910594/page22