Friends,
I try to install Twrp( twrp-3.0-915P_915R4) using Odin, it show success (pass) and reboot,but when i go back to recovery mode its stock recovery !!
any can tell me where i am making mistake
why after successful installation of twrp.tar i am not getting custom recovery
In note edge about me (it show software status : custom)
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
samaly said:
Friends,
I try to install Twrp( twrp-3.0-915P_915R4) using Odin, it show success (pass) and reboot,but when i go back to recovery mode its stock recovery !!
any can tell me where i am making mistake
why after successful installation of twrp.tar i am not getting custom recovery
In note edge about me (it show software status : custom)
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
I remember, that after flashing custom recovery most stock roms reflash the stock recovery during first boot. Try to flash twrp, when process is finished pull battery, put it back in and drictly boot into recovery. When leaving twrp it usually says something like "prevent ROM from flashing stock recovery" which must be answered with "Yes". That should do the trick.
charly-whiskey said:
I remember, that after flashing custom recovery most stock roms reflash the stock recovery during first boot. Try to flash twrp, when process is finished pull battery, put it back in and drictly boot into recovery. When leaving twrp it usually says something like "prevent ROM from flashing stock recovery" which must be answered with "Yes". That should do the trick.
Click to expand...
Click to collapse
Well i flashed the Twrp recovery thrice than finally i got custom recovery
Thank you Charly
Related
Hello,
I'm having problem flashing the orignal firmware package for galaxy Y.
I'm using ODIN v1.85 And downloaded the (Indian) firmware packages form [URL="http://forum.xda-developers.com/showthread.php?t=1465800"[/URL]
It gives me the following messages:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
When I restart my phone it would boot into in custom ROM.
Screen shots attached...
Please help me....
Thank you.
Try flashing it again with another odin file/firmware. Did you a get a green progress bar on your phone while odin process was going on?
Use the odin i am giving here.
https://www.dropbox.com/s/tc32llywhly4nb0/Odin3-v1.85.zip
______________________________________
A HeRo can be AnyOne....© even a PO TA TOE....
Thank you very much i actually flashed another package and its done thanks for your help.:laugh::good:
Just as an added note, always make sure you do an MD5 check on anything you are about to flash in Odin.
I am trying to download the Clockworkmod Recovery via Odin and it consistently fails. I have check many threads and cannot find a solution!
-Phone: Samsung Galaxy SIII SCH-1535
-Carrier: Verizon
-Odin: Tried using 3.07 and 3.04
-Clockworkmod: At first I was using a .tar file or version 5.0.2.8, then I tried using a .tar.md5 version of the same. Then I tried using a .tar.md5 version of 6.0.1.0.
-I am running Windows 7
The results in Odin are as follows:
-PDA checked and file loaded
-Options: Auto Reboot and F. Reset Time
Odin 3.07:
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<ID:0/005> All threads completed. (succeed 0 / failed 1)
Odin 3.04:
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Completed(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
On my phone, it reads: SECURE CHECK FAIL: recovery
Edit:
History...I had Clockworkmod installed previously.
I was downloading CyanogenMod from Rom Manager and it bricked. I unbricked it with
VRALEC.bootchain.tar.md5
BOOTLOADER_I535VRALF2_618049_REV09_user_low_ship.tar.md5
stock.vzw_root66.7z.torrent
Updated to Jellybean 4.04
Stumped.
After unbricking your phone, did you unlock the bootloader again? It needs to be unlocked to flash custom recovery.
dustin_b said:
After unbricking your phone, did you unlock the bootloader again? It needs to be unlocked to flash custom recovery.
Click to expand...
Click to collapse
-_-
Thanks...
Iv tried Odin with all Bl,AP,CP, and CSC Packages it keeps saying FAIL! (Auth) then a blank log then Complete(Write) operation failed.
For the Samsung smart switch the phone us supported. I have the latest verison and my phone is a Galaxy S7 (Us Cellular) Model: SM-G930R4 still says its not supported.
Im stuck idk what to do and i just want my phone working again! Thank you for the help!
Update: Phone wont enter Recovery Mode nor will start just download mode.
Update: got in to show me i need smart switch recovery. Its says my device is not supported and when i try to recovery feature my phone doesn't appear.
When I apply all BL,Ap ect. It shows
SW REC CHECK FAIL: [aboot]Fused 4 > binary 2
[1] eMMC: write Fail: aboot
When just flashing the AP with odin these are the logs
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Its stuck in on the screen telling me to use smart switch pc software
Wont start to boot or go to recovery.
Tried odin start with re-partion and these are the logs farthest i gotten with no errors popping up on my phone
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> skip file list for home binary
<ID:0/005> persist.img.ext4
<ID:0/005> Home Binary Download
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Can't open the specified file. (Line: 1831)
<OSM> All threads completed. (succeed 0 / failed 1)
Try using the modded "Prince Cosmy Odin" with stock firmware first
If that fails, try following this
https://forum.xda-developers.com/galaxy-s7/how-to/unbrick-s7-snapdragon-trying-to-to-t3697441
*Detection* said:
Try using the modded "Prince Cosmy Odin" with stock firmware first
If that fails, try following this
https://forum.xda-developers.com/galaxy-s7/how-to/unbrick-s7-snapdragon-trying-to-to-t3697441
Click to expand...
Click to collapse
I have been using the modded one this entire time does that mean anything?
*Detection* said:
Try using the modded "Prince Cosmy Odin" with stock firmware first
If that fails, try following this
https://forum.xda-developers.com/galaxy-s7/how-to/unbrick-s7-snapdragon-trying-to-to-t3697441
Click to expand...
Click to collapse
I attempted to follow that link so i when through the steps came to step two of downloads and had to find a S7 Snapdragon Root .tar so i did and found this XDA forum https://forum.xda-developers.com/verizon-s7-edge/how-to/root-method-nougat-t3566978 which was the first thing on google searching for the snapdragon.
I followed those steps and i for the error Secure check fail : Boot
I was also able to get it to get into a boot loop once again
When i run odin with the S7_Qualcomm.tar with auto reboot re-partition f. reset time and nand earse all it fails and gives me these logs
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Erase...
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Can't open the specified file. (Line: 1831)
<OSM> All threads completed. (succeed 0 / failed 1)
When running the s7_qualcomm.tar file with only auto reboot and r.reset time I get a PASS with these logs
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
But now my phone is in a boot loop with the logo of samsung S7 and the reovery booting.. is also popping up at the same time.
Enisty said:
I have been using the modded one this entire time does that mean anything?
Click to expand...
Click to collapse
Have you tried the non-modded version?
I'd have used that first
ODIN 3.12.3 or newer
*Detection* said:
Have you tried the non-modded version?
I'd have used that first
ODIN 3.12.3 or newer
Click to expand...
Click to collapse
IT WORKS!
I downloaded this file
USC-G930R4TYU4BQK3-20171221083318.zip
Wish I knew where I got it from but now my phone is actually turning on!
There was a loading screen iv never seen before thought it show
Installing applications with a black bar then smart switch popped up and the bar was filled instantly with yellow lol iv just never seen this screen before from
past uses of any Samsung device.
Good stuff, just be cautious with that model S7, it's a snapdragon meaning much more difficult to unbrick if you brick it as the bootloader is locked
*Detection* said:
Good stuff, just be cautious with that model S7, it's a snapdragon meaning much more difficult to unbrick if you brick it as the bootloader is locked
Click to expand...
Click to collapse
Its really buggy the OS itself. Its slower the normal idk if its just because of how fresh it is like the flash maybe just give it time?
Enisty said:
Its really buggy the OS itself. Its slower the normal idk if its just because of how fresh it is like the flash maybe just give it time?
Click to expand...
Click to collapse
Did you factory reset after the flash (or use CSC to force the reset)?
I'd reset it, it should be pretty smooth after maybe 5 mins of first boot
After flashing twrp-3.0.2-0-n801x.taz with Odin I can't acces Twrp Recovery.
Model: gt-n8013
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 7 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Power btt + volume up don't work fo me. How to acess recovery mode ?
You may have flashed a wrong TWRP or flash did not complete.
JJEgan said:
You may have flashed a wrong TWRP or flash did not complete.
Click to expand...
Click to collapse
what?
i flashed twrp.3.0.2-n801x.tar man
use another recovery man.
Suggest the one twrp.me has listed for your device.That's not the one you flashed.
JJEgan said:
use another recovery man.
Suggest the one twrp.me has listed for your device.That's not the one you flashed.
Click to expand...
Click to collapse
give link? I just found this one for download
www.twrp.me
imakaay said:
After flashing twrp-3.0.2-0-n801x.taz with Odin I can't acces Twrp Recovery.
Model: gt-n8013
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 7 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Power btt + volume up don't work fo me. How to acess recovery mode ?
Click to expand...
Click to collapse
If anyone has this happen after updating the rom you need to enable developer options and Settings developer options activate advanced restart
I am exactly getting the behaviour. No Matter what TWRP or other recovery I've tried to flash on my N8000, odin says successful, but no way to boot on the recovery.
I've tried almost all TWRP version available.
So I downloaded the stock firmware for this phone and I've tried to use odin to flash it. But, it will not flash. If anyone can help me, it would be greatly appreciated. Also, here is the script I got from odin when I try to flash.
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 2365 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Koleman1312 said:
So I downloaded the stock firmware for this phone and I've tried to use odin to flash it. But, it will not flash. If anyone can help me, it would be greatly appreciated. Also, here is the script I got from odin when I try to flash.
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 2365 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Boot your device into recovery mode and then factory reset then wipe cache partition, then power off the device, then boot into download mode and try flashing again.
Sent from my LGL84VL using Tapatalk
Droidriven said:
Boot your device into recovery mode and then factory reset then wipe cache partition, then power off the device, then boot into download mode and try flashing again.
Sent from my LGL84VL using Tapatalk
Click to expand...
Click to collapse
So I forgot to mention that’s the phone is stuck in emergency software mode and I can’t do thing. Also smart switch says the device isn’t supported