At first,i want to clear my issue.
I have karbonn sparkle v (NOT ROOTED).this phone got september update and stuck at android is starting,optimizing applications and google logon screen.
Then i decided to factory reset the phone with recovery boot but didnt works.
i thought that may be recovered from installing old update i.e.august or previous..i searched and downloaded the update file and update from sd card as mentioned in some of the XDA posts...didnot work.
at final,i decided to stock recovery using SP flash tool.got stock rom and driver installed as mentioned in XDA post and other videos as well.MTK VCOM driver as well as mobile drivers installed and stock ROM downlaoded..But when i open latest SP flash tool and try to connect to phone.it did not.. it tried all possible ways to connect like removing battery ,or removing and inserting with volume button pressed or other...while connecting without battery ,nothing happens in PC driver list,no sound nothing.Sp flash tool doesnot recognise chip and downloading /flashing could not happened...
i had flashed some phones using same method and while connecting with pressing volume key ,flashing started.
But i this case ,what happened i dont know,device is not connected but charges and same stuck at boot screen and device manager shows SPARKLE V in portable device list.
I hope some help make my phone .
ranjand said:
At first,i want to clear my issue.
I have karbonn sparkle v (NOT ROOTED).this phone got september update and stuck at android is starting,optimizing applications and google logon screen.
Then i decided to factory reset the phone with recovery boot but didnt works.
i thought that may be recovered from installing old update i.e.august or previous..i searched and downloaded the update file and update from sd card as mentioned in some of the XDA posts...didnot work.
at final,i decided to stock recovery using SP flash tool.got stock rom and driver installed as mentioned in XDA post and other videos as well.MTK VCOM driver as well as mobile drivers installed and stock ROM downlaoded..But when i open latest SP flash tool and try to connect to phone.it did not.. it tried all possible ways to connect like removing battery ,or removing and inserting with volume button pressed or other...while connecting without battery ,nothing happens in PC driver list,no sound nothing.Sp flash tool doesnot recognise chip and downloading /flashing could not happened...
i had flashed some phones using same method and while connecting with pressing volume key ,flashing started.
But i this case ,what happened i dont know,device is not connected but charges and same stuck at boot screen and device manager shows SPARKLE V in portable device list.
I hope some help make my phone .
Click to expand...
Click to collapse
Greetings and welcome to assist. It looks like this may be an issue with finding the correct drivers for your phone. I found this post which may help you
https://forum.xda-developers.com/showpost.php?p=68372526&postcount=4
Good Luck
Sawdoctor
Related
Hello all,
I have been trying to use the SP FLASH tool to obviously flash the recovery img to my mobile which is teh Prestigio 4500tduo
When ever I click the download button and then connect my mobile it picks it up for about 4-5seconds and disconnects from device manager repeatedly.
things I have tried,
Taking the battery out and holding VOL UP & POWERBUTTON
Leaving the battery in and doing the same above
Trying various of drivers
Tried different USB cables & USB ports
Does anybody know how to fix this ? as when it detects the phone the bar at the bottom of FLASH tool go's to RED & 100% then get an error of 4050 which is probably because it didn't flash correctly.
Hope someone can help me as I nearly through the mobile out of the window in frustration ha
Kind regards
Jadc
bump
Right click on sp flash tool and run it as administrator hopefully it works for you and always use latest version of sp flash tool
Sent from my GT-N7100 using xda premium
Jadc007 said:
Hello all,
I have been trying to use the SP FLASH tool to obviously flash the recovery img to my mobile which is teh Prestigio 4500tduo
When ever I click the download button and then connect my mobile it picks it up for about 4-5seconds and disconnects from device manager repeatedly.
things I have tried,
Taking the battery out and holding VOL UP & POWERBUTTON
Leaving the battery in and doing the same above
Trying various of drivers
Tried different USB cables & USB ports
Does anybody know how to fix this ? as when it detects the phone the bar at the bottom of FLASH tool go's to RED & 100% then get an error of 4050 which is probably because it didn't flash correctly.
Hope someone can help me as I nearly through the mobile out of the window in frustration ha
Kind regards
Jadc
Click to expand...
Click to collapse
If your device appears and then disappears in device manager in 3-4 seconds, then this is normal. i think the problem is with your scatter file. download MTKDroidTool and extract scatter file from your phone, then use this file to flash recovery.
So My Friend Cellphone's "LENOVO A369i" has been Bricked .. I tried to fix it connect it for the first time, uploaded the firmware and IT FIXES :good: :fingers-crossed: but after installing CWM it still okay. After I install a Flash ROM when I Start It again It cannot start but I can go to CWM recovery :crying: I NEED TO FIX it
- Help Is Always Accepted
Flash stock firmware back on.
I'm not home or I would search for links sorry.
In Google type your phone name + return to stock.
Sent from my LG-VS980 using XDA Premium 4 mobile app
1165
The Thing is i cant connect the device to the computer when I plug it in .. it ready in a second again .. it none until it's like that over and over again .. tried to reinstall the drivers but no use!!
PauloAgojo277 said:
The Thing is i cant connect the device to the computer when I plug it in .. it ready in a second again .. it none until it's like that over and over again .. tried to reinstall the drivers but no use!!
Click to expand...
Click to collapse
To put the stock rom back on lenovo device, it must be powered off. (if it has a removable battery it must be removed).
preinstal the drivers into pc/laptop.
open device manager
plug in lenovo.
if device manager says 'mediatek,,,,' you are a winner & can use the sp flash tool included in the zipped rom to instal the rom.
if device manager says 'unknown device' you have 2 seconds to click on it & select update driver and a point to the downloaded lenovo driver (then it will be as above).
When you get green circle you are complete and may disconnect and put battery back in.
PauloAgojo277 said:
So My Friend Cellphone's "LENOVO A369i" has been Bricked .. I tried to fix it connect it for the first time, uploaded the firmware and IT FIXES :good: :fingers-crossed: but after installing CWM it still okay. After I install a Flash ROM when I Start It again It cannot start but I can go to CWM recovery :crying: I NEED TO FIX it
- Help Is Always Accepted
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?p=50094020
Here's a step by step guide ..please be aware of the steps .. That help me from bricking my phone almost so many times
Sent from my Lenovo A369i using XDA Free mobile app
If you are using windows 8 then you can't install USB drives
---------- Post added at 02:20 AM ---------- Previous post was at 02:12 AM ----------
PauloAgojo277 said:
So My Friend Cellphone's "LENOVO A369i" has been Bricked .. I tried to fix it connect it for the first time, uploaded the firmware and IT FIXES :good: :fingers-crossed: but after installing CWM it still okay. After I install a Flash ROM when I Start It again It cannot start but I can go to CWM recovery :crying: I NEED TO FIX it
- Help Is Always Accepted
Click to expand...
Click to collapse
So if you are using windows 8 or higher version of windows then simply you have to degrade it to windows 7 or lower to install USB driver's
I wanted to put a new rom on my Lenovo, so I started here: http://forum.xda-developers.com/lenovo-a850/general/tutorial-install-cwm-twrp-lenovo-a850-t2642431
I thought making a backup would be wise.
My Baseband model did not have ROW or CN in it, so after trying all four options EN/CN CWM/TWRP options, all failed an my phone would just reboot.
May be my mistake was trying a few more versions of CWM/TWRP, after one of which my Baseband model was gone...
So I decided to just go ahead and install a new rom without a backup. I installed the VCOM drivers (Win 8.1, a bit of hassle) and downloaded: http://www.needrom.com/download/a850-stock-s123-multilanguagegappsroot/
Тhе flashing process went OK (I got the green circle), but after disconnecting my phone and putting the battery back in, it would not start at all. Not even recovery mode.
I tried flashing another rom, but the PC/flash tool would not detect the phone again.
Тhe only sign of life is the red led when I connect the USB to the PC (without battery).
Any help would be appreciated.
P.S.: Also the phone stopped detecting my SIM cards while trying different CWM/TWRP versions.
P.P.S.: I actually was able to get a response from the flash tool by holding power, volume + and volume -, and got: ERROR 4032 : Enable DRAM failed!
mandulov said:
I wanted to put a new rom on my Lenovo, so I started here: http://forum.xda-developers.com/lenovo-a850/general/tutorial-install-cwm-twrp-lenovo-a850-t2642431
I thought making a backup would be wise.
My Baseband model did not have ROW or CN in it, so after trying all four options EN/CN CWM/TWRP options, all failed an my phone would just reboot.
May be my mistake was trying a few more versions of CWM/TWRP, after one of which my Baseband model was gone...
So I decided to just go ahead and install a new rom without a backup. I installed the VCOM drivers (Win 8.1, a bit of hassle) and downloaded: http://www.needrom.com/download/a850-stock-s123-multilanguagegappsroot/
Тhе flashing process went OK (I got the green circle), but after disconnecting my phone and putting the battery back in, it would not start at all. Not even recovery mode.
I tried flashing another rom, but the PC/flash tool would not detect the phone again.
Тhe only sign of life is the red led when I connect the USB to the PC (without battery).
Any help would be appreciated.
P.S.: Also the phone stopped detecting my SIM cards while trying different CWM/TWRP versions.
P.P.S.: I actually was able to get a response from the flash tool by holding power, volume + and volume -, and got: ERROR 4032 : Enable DRAM failed!
Click to expand...
Click to collapse
Welp, bad luck happened. Try getting it seviced to Lenovo Center.
irfanadli97 said:
Welp, bad luck happened. Try getting it seviced to Lenovo Center.
Click to expand...
Click to collapse
Very helpful, thank you...
After trying many different SP Flash Tool versions and ROM, I was actually able to resurrect my Lenovo by doing a Firmware Upgrade with the latest SP Flash Tool (version 5 something) and using a A850i ROM from needrom.com
No issues so far, but I'm basically back where I started from
i think u have flashed a850 4gb version firmware. same thing happen to my phone. but fixed it with a850i firmware.
I have a karbonn sparkle v(android one) playstore and gmail was not working so I factory reset it. After first boot I got a welcome screen,then sim card setup.After that it shows available wifi which I choose one it shows connected and comes checking connection screen. I almost waited 4-5 hours it still shows checking connection. I have cleared cache partition and data again but no luck. It always get stuck. Pls help....
Softwarelord said:
Bro Read Carefully....
1.Flash Your Karbonn Sparkle v How To Flash Click Here
2. Download Stock Rom click here
please Read How To Flash Carefully...
You Will Get All Solution On This Link.. Read Step By Step...
Click to expand...
Click to collapse
thanks for reply bro...
but I am facing problem in flashing also
installed all mediatek drivers, signature disabled, added legacy software etc still my device is not detected by sp flash tools.
tried different Usb cables, 2 windows 10 system , no detection at all.
is their any alternative?
Softwarelord said:
install mtk vcom driver And click sp flash tool upgrade option
now remove battery and usb cable from cellphone....
now insert battery then cable... you will see detection on sp flash tool
Click to expand...
Click to collapse
This time a popup message appears
The last USB device connected to this computer malfunctioned, and Windows does not recognize it.
images of drivers and pop up messages attached.
but when I changed usb cable their is no pop up and no detection.
Softwarelord said:
Flash in Windows 7 Or Change Usb Cable...
Click to expand...
Click to collapse
Changed usb cable and tried in windows 7, no luck
It always show MTP USB device in device manager as soon as I connect my phone and inserts battery, without battery just nothing.
My karbonn sparkle v android one is running on android 6 marshmallow, few days ago i did a Factory reset on my phone, while the phone was rebooting after wiping all the data , It asked to setup sim card and WiFi after i entered the WiFi password it connected properly and the screen showed "Checking connection.. This might take a while.." .. so i waited but it is remaining is that screen, there is no option to skip that setting.... I have tried rebooting from recovery.. wiping cache partition but again it is struck on that screen.... ............... when i googled about this i saw same problem has happened to some Nexus devices also .. but they are not mentioning any solutions for this.. so If anyone has any idea please help.My karbonn sparkle v android one is running on android 6 marshmallow, few days ago i did a Factory reset on my phone, while the phone was rebooting after wiping all the data , It asked to setup sim card and WiFi after i entered the WiFi password it connected properly and the screen showed "Checking connection.. This might take a while.." .. so i waited but it is remaining is that screen, there is no option to skip that setting.... I have tried rebooting from recovery.. wiping cache partition but again it is struck on that screen.... ............... when i googled about this i saw same problem has happened to some Nexus devices also .. but they are not mentioning any solutions for this.. so If anyone has any idea please help.
I find solution through android one toolkit that unlocked my bootloader and i was able to install twrp also.
Then simply flashed cm 13 and now its working fine.
Hi guys,
I got a OPO borrowed from a friend because my OP3T is going to RMA.
When I first turned it on it had 1% battery. The phone wasn't used for a month. I proceded to recharge the battery. This took almost 18h. I saw the low battery error 3 or 4 times during attempts to power on the handset.
After full charge in installed the latest build of Lineage OS via TWRP. Unfortunately as I was having some WIFI connectivity issues I read that flashing the c7 modem firmware could solve the problem.
I was in TWRP flashing this same zip via sideload with an unbeknownst to me faulty cable. I grabbed the handset mid flash, and it fails with a connectivity error. I tried repeating the process with no luck, as I could not by any means regain adb connection to the handset. And then i decided to reboot and download the zip directly to the phone, without remembering this broken flash attempt could brick the phone. After rebooting I never saw again the One Plus logo neither felt the startup vibration. I tried power cycling with no success, and I cannot by any means detect the phone in windows device manager to attempt the usual unbrick procedures via COLOR or OnePlusRecoveryTool.
Windows doesn't even try to install drivers. It's as if the phone is completely shutdown forever.
What do you think. Did I really hard brick this phone? Is it a battery issue? Any ideas. I really liked to recover the phone to return it to my friend!
Thanks in advance for your help!
joao.m.neto said:
Hi guys,
I got a OPO borrowed from a friend because my OP3T is going to RMA.
When I first turned it on it had 1% battery. The phone wasn't used for a month. I proceded to recharge the battery. This took almost 18h. I saw the low battery error 3 or 4 times during attempts to power on the handset.
After full charge in installed the latest build of Lineage OS via TWRP. Unfortunately as I was having some WIFI connectivity issues I read that flashing the c7 modem firmware could solve the problem.
I was in TWRP flashing this same zip via sideload with an unbeknownst to me faulty cable. I grabbed the handset mid flash, and it fails with a connectivity error. I tried repeating the process with no luck, as I could not by any means regain adb connection to the handset. And then i decided to reboot and download the zip directly to the phone, without remembering this broken flash attempt could brick the phone. After rebooting I never saw again the One Plus logo neither felt the startup vibration. I tried power cycling with no success, and I cannot by any means detect the phone in windows device manager to attempt the usual unbrick procedures via COLOR or OnePlusRecoveryTool.
Windows doesn't even try to install drivers. It's as if the phone is completely shutdown forever.
What do you think. Did I really hard brick this phone? Is it a battery issue? Any ideas. I really liked to recover the phone to return it to my friend!
Thanks in advance for your help!
Click to expand...
Click to collapse
Could be a battery issue too since the device was unused for a month. Did you tried booting into fastboot mode or TWRP?
Which windows are you using?(I suggest you use winXp and win7) Did you tried the qualcomm 2012 drivers from the Color Os toolkit thread and the drivers given on Cm11s restore toolkit thread? -you should know that the fastboot(/adb) drivers will not work for qualcomm diagnostic port method(which the both toolkits are based on).
Mr.Ak said:
Could be a battery issue too since the device was unused for a month. Did you tried booting into fastboot mode or TWRP?
Which windows are you using?(I suggest you use winXp and win7) Did you tried the qualcomm 2012 drivers from the Color Os toolkit thread and the drivers given on Cm11s restore toolkit thread? -you should know that the fastboot(/adb) drivers will not work for qualcomm diagnostic port method(which the both toolkits are based on).
Click to expand...
Click to collapse
No success booting with volume up or down so no fastboot neither twrp. I'm using windows 10 (only one i have). I can't install the drivers because the device doesn't show up on device manager right?
I'll try finding a win XP although I'm sensing the habdset isn't powering at all...
Sent from my ONEPLUS A3003 using Tapatalk
joao.m.neto said:
No success booting with volume up or down so no fastboot neither twrp. I'm using windows 10 (only one i have). I can't install the drivers because the device doesn't show up on device manager right?
I'll try finding a win XP although I'm sensing the habdset isn't powering at all...
Sent from my ONEPLUS A3003 using Tapatalk
Click to expand...
Click to collapse
Yes,as I said, could be a battery issue but we are still not sure yet.I can give you the link for winxp or win7 if you need and then you can dual-boot it alongside windows10.You should install drivers from cm11s restore toolkit thread(executable drivers),maybe then your device will show up in device manager though it is highly advised to do this on Xp or 7 since 8,8.1 and 10 has driver signing issues.