HI,
i've been wanting to root and install custom roms on the i9003. i finally got the courage to try to root and do all these things recently, so i rooted the phone using superoneclick.. but i didnt know what to do next, because i wanted to try out custom roms because of what i have been reading on the forums.
so i followed the instructions here: http://forum.xda-developers.com/showpost.php?p=19442301&postcount=1 and flashed the bagaria.tar found here using ODIN.
but it started looping and kept rebooting over and over again. and got stuck in bootloop. eventually it came up and would respond a bit before going back to the booting sequence, and i noticed that opening CWM automatically sent the phone to booting.
thinking that i did something wrong and afraid that i bricked the device i went to this thread and looked for the dxkp9 stock and used odin with it (http://forum.xda-developers.com/showthread.php?t=1004647)
it just is stuck on boot loop now.
i've tried removing the battery and trying holding the VOLup home and power to no avail.
its just stuck in boot loop.
It is currently stuck in boot loop and wont do anything. i am really hoping it can still be fixed.. a bit of a sentimental value since this was a phone given to me by my dad, and first smartphone as well..
i would be very grateful for any kind of help.
getlucky88 said:
HI,
i've been wanting to root and install custom roms on the i9003. i finally got the courage to try to root and do all these things recently, so i rooted the phone using superoneclick.. but i didnt know what to do next, because i wanted to try out custom roms because of what i have been reading on the forums.
so i followed the instructions here: http://forum.xda-developers.com/showpost.php?p=19442301&postcount=1 and flashed the bagaria.tar found here using ODIN.
but it started looping and kept rebooting over and over again. and got stuck in bootloop. eventually it came up and would respond a bit before going back to the booting sequence, and i noticed that opening CWM automatically sent the phone to booting.
thinking that i did something wrong and afraid that i bricked the device i went to this thread and looked for the dxkp9 stock and used odin with it (http://forum.xda-developers.com/showthread.php?t=1004647)
it just is stuck on boot loop now.
i've tried removing the battery and trying holding the VOLup home and power to no avail.
its just stuck in boot loop.
It is currently stuck in boot loop and wont do anything. i am really hoping it can still be fixed.. a bit of a sentimental value since this was a phone given to me by my dad, and first smartphone as well..
i would be very grateful for any kind of help.
Click to expand...
Click to collapse
1. download stock rom I9003XXKPE from here http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
Unzip and you will find the following files
1. Odin3v1.83(don't use this one, download latest version from here http://forum.xda-developers.com/showthread.php?t=1734997)
2.PIT file latona_20110114
3.BOOT LOADER-APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5 file.
4.PDA-CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5.
5.PHONE-MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5.
6.CSC-GT-I9003-CSC-MULTI-OXAKPE.tar.md.
STEP 1
Go to download mode(press volume down+home then power),once in download mode, connect phone to computer -> double click odin3v1.83(make sure the bar under ID:COM turns yellow)
Double click "PIT" -> look for "latona_20110114" -> click "start", phone will turn off after finish(bar just above ID:COM turns green)
Take the battery out and return -> go to download mode again, connect phone to computer, double click Odin, make sure odin detects your phone, tick PDA, look for "CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5"
tick PHONE, look for "MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5"
tick CSC, look for "CSC-GT-I9003-CSC-MULTI-OXAKPE.tar.md"
Click "start", when it's done, you'll see a "PASS" on the odin, remove phone from computer, phone will restart automatically
Step 2 install value pack
Find and download a value pack of your choice from here http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
I used the stable I9003DDLF2 (2.3.6) after downloaded, unzip the files, you should have "I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5"
Put your phone in download mode, connect to computer, start odin, tick PDA, search for I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5
Click "start", when it's done, you'll see a "PASS" on the odin, remove phone from computer, phone will restart automatically
Step3 apply root(I'm using XDA_Bam's)
Download "PDA_BCK_CF-root_universal_beta14fix.tar" from here http://forum.xda-developers.com/showthread.php?t=1355675
Again in download mode, connect to computer, start odin, tick PDA, search for "PDA_BCK_CF-root_universal_beta14fix.tar"
Click "start", when it's done, you'll see a "PASS" on the odin, remove phone from computer, phone will restart automatically
Step 4 apply custom roms(different roms have different requirements, read the instructions thoroughly)
download any custom rom of your choice, enter recovery mode(volume up + menu + power)
wipe data/factory reset, flash the rom zip(if google gapps is required->go to advanced -> Reboot Recovery -> Flash Google Apps -> reboot system
hard lesson learned
wee2wee said:
1. download stock rom I9003XXKPE from here http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
Unzip and you will find the following files
1. Odin3v1.83(don't use this one, download latest version from here http://forum.xda-developers.com/showthread.php?t=1734997)
2.PIT file latona_20110114
3.BOOT LOADER-APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5 file.
4.PDA-CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5.
5.PHONE-MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5.
6.CSC-GT-I9003-CSC-MULTI-OXAKPE.tar.md.
STEP 1
Go to download mode(press volume down,+menu+power),once in download mode, connect phone to computer -> double click odin3v1.83(make sure the bar under ID:COM turns yellow)
Double click "PIT" -> look for "latona_20110114" -> click "start", phone will turn off after finish(bar just above ID:COM turns green)
Take the battery out and return -> go to download mode again, connect phone to computer, double click Odin, make sure odin detects your phone, tick PDA, look for "CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5"
tick PHONE, look for "MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5"
tick CSC, look for "CSC-GT-I9003-CSC-MULTI-OXAKPE.tar.md"
Click "start", when it's done, remove phone from computer, phone will restart automatically
Step 2 install value pack
Find and download a value pack of your choice from here http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
I used the stable I9003DDLF2 (2.3.6) after downloaded, unzip the files, you should have "I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5"
Put your phone in download mode, connect to computer, start odin, tick PDA, search for I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5
Click "start", when it's done, remove phone from computer, phone will restart automatically
Step3 apply root(I'm using XDA_Bam's)
Download "PDA_BCK_CF-root_universal_beta14fix.tar" from here http://forum.xda-developers.com/showthread.php?t=1355675
Again in download mode, connect to computer, start odin, tick PDA, search for "PDA_BCK_CF-root_universal_beta14fix.tar"
Click "start", when it's done, remove phone from computer, phone will restart automatically
Step 4 apply custom roms(different roms have different requirements, read the instructions thoroughly)
download any custom rom of your choice, enter recovery mode(volume up + menu + power)
wipe data/factory reset, flash the rom zip(if google gapps is required->go to advanced -> Reboot Recovery -> Flash Google Apps -> reboot system
Click to expand...
Click to collapse
:good:
thanks a lot for helping out the newbies like myself.
t is working again and i used the superoneclick method to root my phone.
is there like a recommended "rom" sli9003 users can start with as far as trying things out that arent touchwiz?
i tried (http://forum.xda-developers.com/showthread.php?t=1894737) but i would appreciate it if someone can point me to the right direction. as i am looking forward to learn more
thanks a lot!
getlucky88 said:
:good:
thanks a lot for helping out the newbies like myself.
t is working again and i used the superoneclick method to root my phone.
is there like a recommended "rom" sli9003 users can start with as far as trying things out that arent touchwiz?
i tried (http://forum.xda-developers.com/showthread.php?t=1894737) but i would appreciate it if someone can point me to the right direction. as i am looking forward to learn more
thanks a lot!
Click to expand...
Click to collapse
Make sure you know what you are doing before trying anything....try this http://forum.xda-developers.com/showthread.php?t=1492113
wee2wee said:
1. download stock rom I9003XXKPE from here http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
Unzip and you will find the following files
1. Odin3v1.83(don't use this one, download latest version from here http://forum.xda-developers.com/showthread.php?t=1734997)
2.PIT file latona_20110114
3.BOOT LOADER-APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5 file.
4.PDA-CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5.
5.PHONE-MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5.
6.CSC-GT-I9003-CSC-MULTI-OXAKPE.tar.md.
STEP 1
Go to download mode(press volume down,+menu+power),once in download mode, connect phone to computer -> double click odin3v1.83(make sure the bar under ID:COM turns yellow)
Double click "PIT" -> look for "latona_20110114" -> click "start", phone will turn off after finish(bar just above ID:COM turns green)
Take the battery out and return -> go to download mode again, connect phone to computer, double click Odin, make sure odin detects your phone, tick PDA, look for "CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5"
tick PHONE, look for "MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5"
tick CSC, look for "CSC-GT-I9003-CSC-MULTI-OXAKPE.tar.md"
Click "start", when it's done, remove phone from computer, phone will restart automatically
Step 2 install value pack
Find and download a value pack of your choice from here http://forum.xda-developers.com/showthread.php?p=12310841#post12310841
I used the stable I9003DDLF2 (2.3.6) after downloaded, unzip the files, you should have "I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5"
Put your phone in download mode, connect to computer, start odin, tick PDA, search for I9003DDLF2_I9003ODDLF2_I9003DDLE1_HOME.tar.md5
Click "start", when it's done, remove phone from computer, phone will restart automatically
Step3 apply root(I'm using XDA_Bam's)
Download "PDA_BCK_CF-root_universal_beta14fix.tar" from here http://forum.xda-developers.com/showthread.php?t=1355675
Again in download mode, connect to computer, start odin, tick PDA, search for "PDA_BCK_CF-root_universal_beta14fix.tar"
Click "start", when it's done, remove phone from computer, phone will restart automatically
Step 4 apply custom roms(different roms have different requirements, read the instructions thoroughly)
download any custom rom of your choice, enter recovery mode(volume up + menu + power)
wipe data/factory reset, flash the rom zip(if google gapps is required->go to advanced -> Reboot Recovery -> Flash Google Apps -> reboot system
Click to expand...
Click to collapse
Sir in my case everything goes well but after flashing with step 2 as mentioned above i get an error saying "E does not exist/ not possible" and the phone gets stuck in boot loop again where as after flashing the step 1 it was asking for password.
Pls help
rss31183
rss3183 said:
Sir in my case everything goes well but after flashing with step 2 as mentioned above i get an error saying "E does not exist/ not possible" and the phone gets stuck in boot loop again where as after flashing the step 1 it was asking for password.
Pls help
rss31183
Click to expand...
Click to collapse
After flashing step 1, did your phone restart/reboot normally?..what was asking for password? "everything goes well" for step1?
after flashing the files (pda modem etc.) the phone rebooted. but now is asking for a password go further. and when i tried to enter recovery and set it to factory settings it also asks for password before wiping the divice. tried a few times but with no success.
manu2002 said:
the password is maybe : samfirmware.com ............. maybe i saw it on http://forum.xda-developers.com/showthread.php?p=12310841#post12310841 below every rom
Click to expand...
Click to collapse
Greetings;
I didnt read all the stuff before...
So my answer may not be the best or accurate. (I'm almost out of time - sorry for that).
Either ways this happens to me when you don't perform a clean Flash (Formating Partitions before Flashing, wiping dalvik and cache) and after Flashing; performing a Factory Reset).
After the last step (Factory Reset) it should boot properly.
If not: Remove Battery, place it back and test if it boots.
From my experience: Downgrading ROM also do this issue. But i fix it by Flashing FULL DDLF2 (always with "clean flash") and then after my ROM Boots; Flashing the ROM i want to use.
Hope this helps.
When i flashed the first step my gt i9003 sl went completely blank except a bright light. Any solution or suggestiom
Hello guys.
Im struggeling to install a custom ROM at the stage of installing a CWM recovery. My S2 plus 9105p runs Android 4.2.2 and everytime I try to upload a recovery img via Odin everything works fine as expected but when I try to start (volume up, home, power) the recovery mode - it gets always into the standard Android one - not CWM recovery!!! It looks like Samsung has integrated some kind of security mechanism which keeps us from running custom ROMs...
I have realy tried maybe 5 different recovery images, but non of those worked for me.
Can you please help?
THX
try flashing the files used in this guide
karamancho said:
try flashing the files used in this guide
Click to expand...
Click to collapse
I tried exactly also this particular site and steps described on it, but didn't help... The same problem. Everything was OK, but recovery was not CWM but standard Android one.
When u have flashed ur recorvery, take ur battery out and then plug battery again. And now go to recorvery.
Now it is WORKING !
Hi guys.
I followed the step-by-step guide on this page:
http://forum.xda-developers.com/showthread.php?t=2560928
- used the CWM 6.0.4.5 and Odin3 0.7
- after successfull flash of the PDA with this recovery (manualy unset the auto-reboot option) I have pulled the battery out for a couple of seconds
- the battery came back in again and with home-volUP-Power I got directly to the new CWM recovery.
So thanx all for your support and you can lock this thread as everything is working now.
DETAILED STEPS FOR INSTALLING CWM RECOVERY IF THE PHONE AUTOMATICALLY RE_FLASHES IT:
Installation
WITH ODIN
1. Be sure, that your device is on 4.2.2 stock firmware and shut down the phone
2. Be sure that Samsung drivers are installed on your pc. Just install Kies or google for them
3. Download Odin 3.07(google it) and the CWM-Recovery image (in this case CWM 6.0.4.5 )
4. Open Odin as administrator
5. Start-up the phone by pressing Vol_DOWN + Home + Power so you get into the flash-menu.
6. After reading the disclaimer and warning stuff - simply press Vol_UP and plug the USB cable to the PC and Phone
7. In ODIN click on PDA and select the downloaded CWM-recovery (*filename*.tar.md5) . Check - "F. Reset Time" and UNCHECK!! -> "Auto Reboot"
8. Click start and wait until the blue progress bar in your device is graphicaly 100% (I also suggest to wait another minute to make things sure..)
9. Pull out the battery
10. Pull out the uSB cable from PC and phone
11. Wait abou 10-15 seconds and power up your phone to get into the recovery menu by pressing: Vol_UP + Home + Power
12. DONE
Apologies for dumb questions but I am really newbie with Sony phones (I know my way around HTCs though).
I have the Xperia Z3 Dual (D6633). After some reading, I've managed to unlock bootloader, installed TWRP recovery and rooted the phone.
My wife somehow locked the phone without memorizing password and the brightest idea I've had was to perform factory reset. Accidentally, I have managed to perform a full wipe, wiping everything except mSD card (I have experience with CWM recoveries but not with TWRP). I did not backup software before accidental wipe.
Phone obviously wont boot but I am having hard time to get to recovery as well, phone just hangs with TWRP recovery logo on the screen.
The first step I intend to perform is to try to re-flash recovery again a go from there.
My intention is to restore stock ROM using Flashtool and d6633_23.0.f.1.74_1288-7362_r8b_ru.ftf
I've read how to enter appropriate boot mode, however, I am not sure witch one to choose for Flashtool to work. BTW, is it possible to restore stock software using Sony PC Companion software?
Can anyone point me in a right direction? A simple guide to follow to in order to get out of this tough situation?
Download your desired firmware and install latest flash tool on your computer.
Copy the downloaded firmware on to the flash tool folder which can be found on your C drive.
Hold volume up and power together till your phone vibrates thrice (power shut down)
Now open flash tool, select flash mode and then your firmware. Now press start.. You will see animation there asking you to connect your device.
Hold your phone's "down volume button" and connect it to the computer. Flash tool will recognize the device and starts flashing. Wait for it to finish.
Boot your device and you are good to go!
creative70 said:
Download your desired firmware and install latest flash tool on your computer.
Copy the downloaded firmware on to the flash tool folder which can be found on your C drive.
Hold volume up and power together till your phone vibrates thrice (power shut down)
Now open flash tool, select flash mode and then your firmware. Now press start.. You will see animation there asking you to connect your device.
Hold your phone's "down volume button" and connect it to the computer. Flash tool will recognize the device and starts flashing. Wait for it to finish.
Boot your device and you are good to go!
Click to expand...
Click to collapse
Success! Thank you for your hand holding.
Order of steps to get the phone to flash mode was slightly different in my case though. When I pressed volume up and power key the device did not react. Repeating the same process with USB cable inserted worked. When pressing volume down the phone was tying to get to recovery but then it hanged there. In the end when Flashtool asked me to connect the phone, I've kept pressing volume down key with phone turned off and inserted USB cable and it got recognized and software got flashed in the end. BTW, Flashtool does't contain drivers for Z3 yet, therefore I've installed drivers for Z1 / Z2 in addition to flashmode and fastboot drivers.
Currently I am updating software trough Sony Update and then I will check if bootloader is still unlocked ant will try to get to recovery. If no luck I will reflash recovery.
Thank you again!
P.S. I've noticed that there are slightly different application included in this ROM. FTF file in these forums is a slightly different version that came with my phone originally. It might be useful to get more versions of FTFs for D6633 model uploaded...
Hey, in this tutorial I'll tell you how to unbrick hard-bricked Tab 3.
So, if you have message that you must repair your Tab 3 in Samsung Kies, and you can't recover it (you have corrupted system and have no recovery), first thing that you must do is to download Odin here: http://odindownload.com/ and TWRP recovery (make sure that you downloaded the version for your tablet): version for model P5200 - https://goo.gl/mzY5kV and for model P5210 - https://goo.gl/mcxy3E. Then download stock ROM from sammobile.com. WARNING! Never flash ROM on the tablet in such a state. When you do this, you'll see FAILED message in Odin and you won't repair anything. Then you must turn off tablet and boot into download mode (hold power+volume down+home). Then connect your tablet to the computer and open Odin with administrator rights. Now you gonna to click AP button and locate and open twrp file (with .md5 extension) and when it is loaded click Start button. When recovery is flashed, plug off the cable and then you must turn off your tablet and boot into recovery mode (hold power+volume up+home). Now you must click Wipe>Advanced Wipe and mark everything (without USB-OTG and SD Card) and click button Wipe. After wiping, you must click Reboot and Download. You'll be in download mode and make sure that there isn't any text in the upper left corner. When there isn't anything then this means that you haven't anything on your tablet. Now you must open Odin again and plug the cable in. Then click AP button and locate and open your ROM. Now you must click Start and wait. When the ROM is flashed, the tablet should restart automatically. Then unplug the cable and wait for the tablet to boot. After few minutes, you should see the welcome message. When you see it, it means that tablet is working and the repair is completed.
I hope that this tutorial helped you
this is not hard bricked this is soft bricked. hard bricked is when you cannot turn on your device to enter the recover and download mode. i hope you do your research. please correct the title.
Crash Recovery for the Samsung Galaxy A20
1. Be Prepared
Most of us will suffer from a crash at some time. If you know how to fix it, you will have a lot less stress.
There are certain files you need to keep in readiness.
Always backup boot, data, system before you try any new ROM.
A. On your PC
- Firmware you downloaded from one of these sites
https://samfrew.com or https://www.samfirmware.net
or for a faster download: https://forum.xda-developers.com/galaxy-a20/how-to/a20-repair-firmware-t4066551
- recovery.tar you can download from here https://forum.xda-developers.com/galaxy-a20/how-to/guide-quick-root-twrp-galaxy-a20-t4069423
B. On your A20 external sd
Don't keep any important files on your internal sd card. Keep backups on the external sd and on usb otg.
- Boot, data, system backup
- Disable_Dm-Verity_ForceEncrypt_08.18.2019.zip
or this one
View attachment 4975463
To go to download mode
Normal method
1. Turn off phone
2. Hold down both volume keys
3. Plug in computer
Bootlooping
1. Plug in to computer
2. Hold down both volume keys
For a difficult phone
1. Connect usb to computer but not to phone
2. Hold down all 3 keys
3. When it buzzes release power and quickly plug in usb to phone.
It might take a few times to get it right.
If it's REALLY BAD
1. Wait for the battery to completely run down and use normal method.
2. Soft Crash
This is when you get a bootloop.
Recover method
1. Reboot into TWRP( hold down all 3 keys and release vol down when it reboots)
2. Restore your backup.
3. Hard Crash
This is when you get red text along the top.
Recover method
1. Connect phone cord to PC
2. Reboot into download mode (Hold down all 3 keys
When the phone reboot release power key and plug in to computer at the same time
It may take a few times to get the timing right)
3. Flash each part of the firmware into its slot.
BL_20xxxxxxx.tar.md5 goes into the BL slot
AP_20xxxxxxx.tar.md5 goes into the AP slot
CP_20xxxxxxx.tar.md5 goes into the CP slot
HOME_CSC_xxxxxx.tar.md5 goes into the CSC slot
4. You might do a Factory data reset
5. Wait for the restart
6. Skip through a minimal setup
7. Activate developer mode
8. Allow usb debugging
9. Reboot into download mode
10. Flash recovery.tar in the AP slot
11. Reboot the A20 into TWRP and mount everything that you can.
12. Format Data (not just wipe) - don't restart
13. Flash Disable_Dm-Verity_ForceEncrypt
14. Wipe both caches then go back and Reboot into Recovery.
15. Restore your data backup.
16. Reboot
physwizz collection
A collection of guides, kernels and ROMs. Guides Complete Guide to the A20 GSIs for the A20 Quick Root and TWRP for the A20 Making my First Kernel for the A20 A20 Rooting Guide Making Your Own ROM Making Your Own Version of QwizzROM-a20...
forum.xda-developers.com
If anyone finds a better way to do this, please let me know.
physwizz said:
If anyone finds a better way to do this, please let me know.
Click to expand...
Click to collapse
Link to that version on dmverity pkease
shumway66 said:
Link to that version on dmverity pkease
Click to expand...
Click to collapse
Done,
I have FBE not present in TWRP recovery, is that a problem?
Engineer_Virus said:
I have FBE not present in TWRP recovery, is that a problem?
Click to expand...
Click to collapse
8. Reboot the A20 into TWRP and mount everything that you can.
9. Format Data (not just wipe)
10. Flash Disable_Dm-Verity_ForceEncrypt_08.18.2019.zip
11. Reboot into Recovery.
physwizz said:
8. Reboot the A20 into TWRP and mount everything that you can.
9. Format Data (not just wipe)
10. Flash Disable_Dm-Verity_ForceEncrypt_08.18.2019.zip
11. Reboot into Recovery.
Click to expand...
Click to collapse
Please how to boot manually to download mode? I have installed Carlos Kernel and my phone has black screen after Samsung boot logo.
Dan225 said:
Please how to boot manually to download mode? I have installed Carlos Kernel and my phone has black screen after Samsung boot logo.
Click to expand...
Click to collapse
turn phone off
connect to computer and hold down both volume keys
but for twrp mode
hold all 3 buttons until the phone reboots and release volume down
When it arrives at recovery it crashes and ends with error
jp_f said:
When it arrives at recovery it crashes and ends with error
Click to expand...
Click to collapse
More information
physwizz said:
Crash Recovery for the Samsung Galaxy A20
1. Be Prepared
Most of us will suffer from a crash at some time. If you know how to fix it, you will have a lot less stress.
There are certain files you need to keep in readiness.
Always backup boot, data, system before you try any new ROM.
A. On your PC
- Firmware you downloaded from one of these sites
https://samfrew.com or https://www.samfirmware.net
or for a faster download: https://forum.xda-developers.com/galaxy-a20/how-to/a20-repair-firmware-t4066551
- recovery.tar you can download from here https://forum.xda-developers.com/galaxy-a20/how-to/guide-quick-root-twrp-galaxy-a20-t4069423
B. On your A20 external sd
Don't keep any important files on your internal sd card. Keep backups on the external sd and on usb otg.
- Boot, data, system backup
- Disable_Dm-Verity_ForceEncrypt_08.18.2019.zip
or this one
View attachment 4975463
To go to download mode
Normal method
1. Turn off phone
2. Hold down both volume keys
3. Plug in computer
Bootlooping
1. Plug in to computer
2. Hold down both volume keys
For a difficult phone
1. Connect usb to computer but not to phone
2. Hold down all 3 keys
3. When it buzzes release power and quickly plug in usb to phone.
It might take a few times to get it right.
If it's REALLY BAD
1. Wait for the battery to completely run down and use normal method.
2. Soft Crash
This is when you get a bootloop.
Recover method
1. Reboot into TWRP( hold down all 3 keys and release vol down when it reboots)
2. Restore your backup.
3. Hard Crash
This is when you get red text along the top.
Recover method
1. Connect phone cord to PC
2. Reboot into download mode (Hold down all 3 keys
When the phone reboot release power key and plug in to computer at the same time
It may take a few times to get the timing right)
3. Flash each part of the firmware into its slot.
BL_20xxxxxxx.tar.md5 goes into the BL slot
AP_20xxxxxxx.tar.md5 goes into the AP slot
CP_20xxxxxxx.tar.md5 goes into the CP slot
HOME_CSC_xxxxxx.tar.md5 goes into the CSC slot
4. You might do a Factory data reset
5. Wait for the restart
6. Skip through a minimal setup
7. Activate developer mode
8. Allow usb debugging
9. Reboot into download mode
10. Flash recovery.tar in the AP slot
11. Reboot the A20 into TWRP and mount everything that you can.
12. Format Data (not just wipe) - don't restart
13. Flash Disable_Dm-Verity_ForceEncrypt
14. Wipe both caches then go back and Reboot into Recovery.
15. Restore your data backup.
16. Reboot
Click to expand...
Click to collapse
hello sir, i need help.
after rooting my phone succesfully and try to using eureka kernel my phone just get bootloop. before that, i dont know why i cannot backup data, system and etc you just write on guide. then i enter download mode and inadvertenly pressing "dont unlock bootloader". now my phone just stay in download mode with text writed on it in red colour "vbmeta: error verifying vbmeta image..."
if it can be fixed please tell me how to fix that. Thank you very much @
Astreinz said:
hello sir, i need help.
after rooting my phone succesfully and try to using eureka kernel my phone just get bootloop. before that, i dont know why i cannot backup data, system and etc you just write on guide. then i enter download mode and inadvertenly pressing "dont unlock bootloader". now my phone just stay in download mode with text writed on it in red colour "vbmeta: error verifying vbmeta image..."
if it can be fixed please tell me how to fix that. Thank you very much @
Click to expand...
Click to collapse
Try again.
This time use a long press to unlock
cant even boot into download mode or twrp i actually have a scv46 that is actually samsung a20 rip my phone
louiskaneko said:
cant even boot into download mode or twrp i actually have a scv46 that is actually samsung a20 rip my phone
Click to expand...
Click to collapse
For a difficult phone
1. Connect usb to computer but not to phone
2. Hold down all 3 keys
3. When it buzzes release power and quickly plug in usb to phone.
It might take a few times to get it right.
If it's REALLY BAD
1. Wait for the battery to completely run down and use normal method.