Related
I received my amFilm tempered glass screen protector 3 days ago. The packaging of all the contents came in a hard clear plastic which included:
Tempered glass screen protector
Rear PET screen protector
An alcohol wipe
A dry wipe
6 dust removing stickers
Micro-fiber cloth
Squeegee card
Instructions
Following the instructions, of course I washed my hands to remove any oils/dirt. Tip- I would suggest doing this in an area as clean as possible. TIP: states do it in the bathroom after a hot shower has been running so the steam settles any dust. I've done this on Zagg screen protectors and it works, but I failed to do this which caused troubles during installation.
I powered down the phone and wiped the screen with the included alcohol wipe. Then using the dry wipe i wiped off any excess liquid (which was not very much). I used the micro-fiber cloth to wipe the screen down one more time. Looking a the screen i saw one strand of fiber/dust, which then I used the stickers included which lifted it right off.
Installing the tempered protector was fairly straight forward. I tried to center the screen protector and used the home button to gauge how off center to the left and right I was and if the glass was angled in relation to the top of the home button. I made sure the glass was straight along both sides of the screen and placed it down. You do need to press in the center vertically and horizontally for the glass to set well.
Lifting the glass up was pretty easy using a finger nail, I had to lift it off because debris got under and got attached to the tempered glass. I used the dust sticker again and it removed the debris with ease. Positioning the tempered glass again I got it this time. For some reason the edges of the tempered glass still have this look that the sticky backing isnt completely pressed down. I try for 30sec-1min to hold my thumb on these areas and it comes back. That look when an air bubble is under and it wont get pressed out is the best I can describe.
I'm a perfectionist, this probably caused installing it harder than it should have been.
Yes there is a gap about 3 credit cards thick between top and bottom. I do wish it covered more toward the bottom and under the home button and reaching up between the front camera and earpiece grill.
There is also a gap of about 2 credits from the sides of the tempered glass and my Spigen Hybrid Crystal case. I understand why they did this because different cases grip around the front of the phone differently, so to be compatible the width of the tempered glass is just wide enough to cover the actual screen.
Just wish the tempered glass covered a little more.
The thickness of the amFilm tempered glass is .33mm. This makes the glass just a tad higher than the home button, which makes it nice as its more comfortable when my thumb may be at the bottom and it feels more flush than having the home button raised.
Another thing i notice is the softkeys at the bottom emit a glow just below the tempered glass ends. This annoys me because I feel the glass wasnt properly measured.
The glass is very smooth and attracts less finger prints than without it or on my bare LG G2 screen (having no screen protector).
After 3 days of use, there still are those areas around the screen that will not go away (See photo below). At the moment that is the only thing bothering me. It feels nice and visibility is perfectly clear, touch response has gone unchanged as well.
For the price of $7.99 + free shipping (at the time of me writing this) on Amazon http://www.amazon.com/gp/product/B00UH8KKA0/ref=cfb_at_prodpg
its not bad and for that price can't go wrong with it. It comes with a rear PET screen protector, which I did not install. So there is extra benefit :good: (I have plans to install a dBrand rear skin).
Feel free to ask any questions.
Here are some pictures of everything described.
I took your advice and ordered one. Thanks for taking the time to review this screen protector. I appreciate it. I'll get it in a couple days. I'm sure it will do just fine. It seems from your description that installing it is simple enough. Thanks again.
I have this. It cracks if you just drop the phone onto a hard surface from like 1 or 2 inches high. Very fragile... They replaced first one for free. I don't know if they will replace the second one. But, I'm happy it's there to take the impact in stead of the real screen..
There are glass sp 0.2-0.25mm thickness for less than $5 on ebay. They work just as well, if not better.
After having seen all of the issues with the glass screen protectors for this phone, I decided that I needed to try something else in the meantime. While I have a Sakai glass one that I ordered from ebay that is due roughly a month from now, I'm not very hopeful for it working. As a result of all of this and the need for a screen protector ASAP, I went with the Spigen screen protectors that I have seen mentioned on here. Having used PET films in the past, I was expecting a huge hassle. Bubbles, cheap feeling etc. Turns out, these worked REALLY damn well, to my complete surprise.
Installation:
Installation was quite easy, much easier than the older thin film screen protectors that I remember. You simply clean the surface of the phone, following the instructions. Place the tabs on the screen protector to help you position it. Then carefully position it properly keeping an eye on the edges and the sensors. It adheres to the screen very much like a glass screen protector does. There are a few small bubbles here and there, but they squeegee right out. I ended up with two permanent bubbles (one by the light sensor and one near the edge). Neither were the fault of the screen protector, both were caused by me rushing and nicking the surface of the screen protector when squeegee-ing the bubbles out. I think I could easily get it on there next time with zero bubbles. Way less hassle than any other attempt I have had with a film screen protector. One complaint I have is that they only included one alcohol wipe (everything else is in multiples), I don't know if I just got unlucky or they aren't thinking. Anyways, I have access to many solvents at work. No big deal for me.
Result:
How does it feel? A bit more plasticy than the usual glass screen protector but otherwise surprisingly nice. It adheres to the curves perfectly with no major bubbles, clarity-wise it is crystal clear. I honestly can't tell it is there. It adheres nicely to the curves of the display without any gaps (other than my nicks at the edge). My Otterbox Commuter case fits right over the top of it with ZERO problems. I was expecting these to be a stop-gap measure until the better glass ones come out but honestly I don't see anything wrong with these as is and would be just fine using these alone. I am not sure about longevity as I just installed it but so far I am actually surprisingly happy with it, especially for the cost. If you are on the fence between glass and plastic. Go with these plastic screen protectors for now and let the manufacturers work out the difficulties of the glass ones. Then you can decide later if you really want the glass one for you phone.
Link:
https://www.amazon.com/gp/product/B01B1GQDGG/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
it will get scratched to **** within 2 weeks don't worry. Then you'll have to use another of the 3 that came with it.
Agreed with everything that OP posted, and agreed with the person above. Mine got scratched within a day but I got over it.
I installed one only because I tried three different Temper glass ones and none sealed correctly. I like it so far installed very good, covers the entire screen. So far so good.
I got a soft screen protector from AliExpress. It's a bit tricky to apply at first but once you get the idea it's not so bad.
The screen protector is really good! It's like silicon , doesn't get scratched easily.
Best part? it's 1.4$ each! What else can you ask for..?
Link:
http://www.aliexpress.com/item/For-LG-G5-Full-Coverage-Soft-Screen-Protector-Guard-Film-for-LG-G5/32618522429.html?spm=2114.13010608.0.54.iHJztH
Here:
Yup good screen protector but it does scuff, so is it perfect no, but one of the better non temper glass protector
I just tried and failed to apply all three. I can't be doing with bubbles or marks on the screen, and who in their right mind decided to put adhesive on a screen protector.
First one too many bubbles, second one, dust, bubbles and scratches, third one, same.
Add to the fact it feels like a ZAGG invisible shield, rubbery rather than glassy.. I will keep it naked from now on.
I have an Xtreme skin skin to install, wish me luck, i'll bloody well need it haha.
Jonathan-H said:
I just tried and failed to apply all three. I can't be doing with bubbles or marks on the screen, and who in their right mind decided to put adhesive on a screen protector.
First one too many bubbles, second one, dust, bubbles and scratches, third one, same.
Add to the fact it feels like a ZAGG invisible shield, rubbery rather than glassy.. I will keep it naked from now on.
I have an Xtreme skin skin to install, wish me luck, i'll bloody well need it haha.
Click to expand...
Click to collapse
I got the dark oak Xtremeskin!
I've put on a tempered glass before, it was kinda bad, lost saturation and brightness, and i got a clear case from spigen, but the case's lips protudes to the center so much that it started to push the screen protectir out!, I eventually removed the tempered glass... Not usre which screen protector to apply on with the spigen case :/
The Spigen Crystal Clear is too thin in my opinion - I killed it within a week. My old Spigen Steinheil Ultra on the S4 was way better. Purchased a CrocFol Premium instead.
Yup I have to change my opinion as well, used it for a bit, scuffed easily, stays clear without the rainbow effect. I had a few defects in my screen protectors, changed them out. Using the otterbox Defender case for now.
1$ tempered glass (rectangular) from AliExpress are perfect of you dont care leaving the top curved part unprotected. No bubbles, no rainbows, no effect on colors\contrast\clarity.
I have skimmed through the pages in the other tempered glass screen protector threads. I have yet to find a manufacturer who makes an edge to edge protector that adheres to the entire screen rather than just the top and bottom.
My issue is that with a water proof device, anytime it is exposed to water (every day for me as I place it on the shelf in the shower to listen to music), water becomes trapped underneath the tempered glass.
Anyone picked up a model that would remedy this?
no one currently makes one
Why did you feel the need to open a whole new thread for something that has been discussed at length in many other threads? no, there is no solution yet.
Doesn't the official Samsung one do this ?
The official Samsung one is plastic, not glass.
The official Samsung one is not tempered glass.
I strongly advice against getting curved tempered glass. Or any screen protector with curve protection.
I got my replacement Note 7 and I decided to just use a flat film protector and leave the sides exposed. So much easier to use this way.
which flat one did you get!
Sent from my SM-N930T using Tapatalk
BozQ said:
The official Samsung one is not tempered glass.
I strongly advice against getting curved tempered glass. Or any screen protector with curve protection.
I got my replacement Note 7 and I decided to just use a flat film protector and leave the sides exposed. So much easier to use this way.
Click to expand...
Click to collapse
I went nude screen on the explosive n7 because i knew i was going to exchange it and i only managed to get one scratch and it was on the edge. I think i know how it happened.
Be careful
BozQ said:
The official Samsung one is not tempered glass.
I strongly advice against getting curved tempered glass. Or any screen protector with curve protection.
I got my replacement Note 7 and I decided to just use a flat film protector and leave the sides exposed. So much easier to use this way.
Click to expand...
Click to collapse
It feels like **** though. I had an IQ Liquid Shield on my old Note 7, and it felt nice in the hand. Barely a bump in feeling, some around the edges but not really noticeable. This current new Note 7 has factory screen protectors, both front and back. But they feel sharp and edgy, they don't cover the curves. I have actual sleeping nightmares about applying a brand new IQ Liquid Shield protector I already have, and it peeling horribly at corners. fEa.r me..?
Yeah. So I got my replacement n7 today. Picked up a Qmadix "first defense" screen protector. Guess what? It's edge to edge and the adhesive goes all the way around the screen. Just got out of the shower (phone got soaked), no water under the glass.
There is no reason to be rude.. Obviously, the other threads "discussed at length" on the subject failed to stumble upon this gem.
Thanks everyone. I'm only 5 hours in but I have no complaints. No halo, sits flush. Thicker than the Verizon branded one I had previously. Has kind of a unique cut out for the Samsung logo. I also purchased a camera, hearbeat sensor, and home button glass.. I'm set lol.
Edit: forgot to mention the Qmadix also comes in all three colors. I purchased black respectively.
filthimoney said:
Yeah. So I got my replacement n7 today. Picked up a Qmadix "first defense" screen protector. Guess what? It's edge to edge and the adhesive goes all the way around the screen. Just got out of the shower (phone got soaked), no water under the glass.
There is no reason to be rude.. Obviously, the other threads "discussed at length" on the subject failed to stumble upon this gem.
Thanks everyone. I'm only 5 hours in but I have no complaints. No halo, sits flush. Thicker than the Verizon branded one I had previously. Has kind of a unique cut out for the Samsung logo. I also purchased a camera, hearbeat sensor, and home button glass.. I'm set lol.
Edit: forgot to mention the Qmadix also comes in all three colors. I purchased black respectively.
Click to expand...
Click to collapse
Other threads didn't find this so called gem of yours, then mention it there, that's the whole point of the original tempered glass thread. To discuss solutions. Not make a new thread for the EXACT same thing. It's just annoying to have multiple threads for literally the exact same topic. Surely you get that.
Anyway. Do u have any photos or share so we can see how it looks?
Sent from my SM-N930F using Tapatalk
Not sure if anyone has seen this yet, I don't know if it is full adhesive or not...... http://zerolemon.com/product/case-f...-for-samsung-galaxy-note-7-lifetime-warranty/
probably not full adhered.
Snowleopard1900 said:
Not sure if anyone has seen this yet, I don't know if it is full adhesive or not...... http://zerolemon.com/product/case-f...-for-samsung-galaxy-note-7-lifetime-warranty/
Click to expand...
Click to collapse
i tried dozens of them looks just like that, most of them only have adhesive on the sides or the top+bottom. all returned.
i suspect this one will be the same, but its not available to purchase on Amazon yet. Guest i will try this too.
i will report see how it goes. but i have no hope at all.
case friendly and curved too on the design like that..?? dont know thats legit or not.
This will work 100%, even my case won't peel the screen cover.
http://imgur.com/a/sq0n5
https://amzn.com/B01HN2T6YI
you must get this specific version for the full cover. there's a lot of different variations. also let the film completely dry before you even attempt to wrap down the sides. you can use your palms, squeegee, and blow dryer. Remember the water spray is only for help with placement. When this film dries, its very stick and adhesive.
i just hate TPU material, its spongy, soft, leaves imprints and a weird texture. but it does full cover. tempered glass and PET film will never do that.
chillsen said:
This will work 100%, even my case won't peel the screen cover.
http://imgur.com/a/sq0n5
https://amzn.com/B01HN2T6YI
you must get this specific version for the full cover. there's a lot of different variations. also let the film completely dry before you even attempt to wrap down the sides. you can use your palms, squeegee, and blow dryer. Remember the water spray is only for help with placement. When this film dries, its very stick and adhesive.
i just hate TPU material, its spongy, soft, leaves imprints and a weird texture. but it does full cover. tempered glass and PET film will never do that.
Click to expand...
Click to collapse
Your case doesn't even go around all the edges.
borijess said:
Your case doesn't even go around all the edges.
Click to expand...
Click to collapse
the sides of the case overlap the screen protector with zero lifting. it would obviously work the same way for any case, even those that cover the top and bottom
chillsen said:
the sides of the case overlap the screen protector with zero lifting. it would obviously work the same way for any case, even those that cover the top and bottom
Click to expand...
Click to collapse
I have the same protector updated version on my note 7. Did the shrink wrap trick too when i applied it. Came out nice after 12hrs. Once I put my UAG case it started to lift edges. I had to use a credit card to slide case phone in without lifting edges. So I thought I was all good right. Nope a day later it started to lift on the top side and bottom side. I have to smooth it back to down continuously. So either you got lucky or you case does not life the edges.
borijess said:
I have the same protector updated version on my note 7. Did the shrink wrap trick too when i applied it. Came out nice too. Once I put my UAG case it started to lift edges. I had to use a credit card to slide case phone in without lifting edges. So I thought I was all good right. Nope a day later it started to lift on the top side and bottom side. I have to smooth it back to down continuously. So either you got lucky or you case does not life the edges.
Click to expand...
Click to collapse
maybe it was the way you put it on? as in one side you will comfortable be able to tuck it under but the other side kinda snapped on and slid/lifted the cover in order for the case to snap on?
mahdibassam said:
Other threads didn't find this so called gem of yours, then mention it there, that's the whole point of the original tempered glass thread. To discuss solutions. Not make a new thread for the EXACT same thing. It's just annoying to have multiple threads for literally the exact same topic. Surely you get that.
Anyway. Do u have any photos or share so we can see how it looks?
Sent from my SM-N930F using Tapatalk
Click to expand...
Click to collapse
Not sure if you found it yet, but here is the screen protector he was mentioning. Got good reviews (from a handful of people so far) but is pretty pricey at $35 U.S.
ohblindone said:
Not sure if you found it yet, but here is the screen protector he was mentioning. Got good reviews (from a handful of people so far) but is pretty pricey at $35 U.S.
Click to expand...
Click to collapse
Just installed this. I think i know why most companies only use glue on the top or bottom. The quality of the product is good. The packaging is great but i would rather get something a little more simple and maybe save on the cost.
I have yet to turn on my replacement N7 so i cant speak on clarity but the fit is decent. It even works with my Seidio Dilex case on even though its "full screen"
Here is my one problem so far (its only been an hour since install) there is a slight clicking sound when you press on some areas. The edges etc. This is the reason why i think most companies dont use glue on the sides. I think this is where the clicking sound is coming from. I think i installed it as best as i could but who knows. Maybe its my fault.
Im going to try to use it for a while to see how well it works and if i can stand the clicking sound. This is my 1st glass screen protector for the N7 and i dont think ill try more in the future. I just wanted to try one out.
I know what your thinking...ANOTHER THREAD DISCUSSING THIS!!??!!
Let me just say I didn't do this on purpose. I stumbled onto this combination by accident. And I'm just gonna say that it's almost like the old Reeses cup commercials. You got your chocolate in my peanut butter!!
Ok, I got these screen protectors this morning from China. They were the standard glass screen protectors. I received a Clear and a Black. I immediately installed the Clear. It looked good. I had an appointment to get to so...I put the Otterbox Defender case back on my phone with the glass screen protector to at least protect the phone while I was out. It was a tight fit!!
This combination was horrible. I had to press extra hard and i was fairly annoyed. FFW a couple hours. I get home, the phone has been in my pocket and I notice the plastic shield on the Defender, along the adges looked a little dirty, I had to take the glass off too, so I take the case apart and the plastic shield was coming off of the frame that it attaches to. UGH!!! I started to take a few pictures of the problem to send to Otterbox. I had also removed the clear glass screen protector. I started thinking.....BINGO!!
I removed the clear protector on the Otterbox (someone else in the threads mentioned they did this...thanks for the idea). I installed the black edged Glass screen protector and reassembled everything. I must say....this is is the best I've seen. It's an expensive combination....and an unintended surprise.
The company for these Glass Screen protectors is as follows:
Dongguan Strawberry Electronic CO, Ltd
Sara (she is really cool to deal with) WeChat contact ID ps216816
These guys can also be found via Alibaba.com
I don't have a cost...I paid for shipping and they provided me the samples. I didn't receive these protectors in a product box. Just 2 protectors in identical sleeves (pictured below)
Here's the installed Black Glass and Modified Otterbox defender case:
I'm not sure how long this will last...the Glass had glue all the way around the edges. The home button has glue all the way around it. The headset speaker has glue all the way around it. The cutouts for the cameras have no glue.
I'm not promoting anyone or anything. I'm only saying this is working for me at this exact moment in time.
I always remove the plastic screen protectors from OtterBox defenders... They do nothing but gather dust/dirt and create rub marks around the plastic edges over time.
Sent from my Galaxy Note7 using Tapatalk
hotspace said:
I'm not promoting anyone or anything. I'm only saying this is working for me at this exact moment in time.
Click to expand...
Click to collapse
Enjoy it for the first one hour
Sent from my SM-N930T using Tapatalk
Now that people are starting to receive their phones and accessories from OnePlus, I am very curious to hear people's thoughts on the official tempered glass protector offered from OnePlus.
Specifically, how does it fit with the OEM cases OnePlus offers. Most importantly, does it fit with the thicker OnePlus Bumper cases?
The good news, according to OnePlus's official install video posted on their website, it does look like it fully adheres to the screen.
https://www.oneplus.com/oneplus-6-3d-tempered-glass-screen-protector
Looking forward to feedback before I place an order for one to potentially replace the pre-applied plastic screen protector.
sn0warmy said:
Now that people are starting to receive their phones and accessories from OnePlus, I am very curious to hear people's thoughts on the official tempered glass protector offered from OnePlus.
Specifically, how does it fit with the OEM cases OnePlus offers. Most importantly, does it fit with the thicker OnePlus Bumper cases?
The good news, according to OnePlus's official install video posted on their website, it does look like it fully adheres to the screen.
https://www.oneplus.com/oneplus-6-3d-tempered-glass-screen-protector
Looking forward to feedback before I place an order for one to potentially replace the pre-applied plastic screen protector.
Click to expand...
Click to collapse
I don't get my phone until later today, so I can not confirm until then. But the two different customer service reps I talked to guaranteed the TGP works with the OEM bumper cases. They said the only case it isn't compatible with is the outterbox case.
suprstar29 said:
I don't get my phone until later today, so I can not confirm until then. But the two different customer service reps I talked to guaranteed the TGP works with the OEM bumper cases. They said the only case it isn't compatible with is the outterbox case.
Click to expand...
Click to collapse
Looking forward to your results! If it does fit with the OEM bumper case (specifically the Nylon bumper case for me) I'll use my $20 promo voucher to order the glass protector as well.
I will say the preapplied plasic protector surprised me.wkth how good it feels. I usually do a glass protector but once I get my I will probably leave the plasitc on to see how it wears. Be good for the long term review since most on even know it's there at first
Sent from my Pixel 2 using Tapatalk
Here take a look at this. I''ve just posted it to the official forums to I'll C+P here;
----
Hi all,
Hope you've not forgotten me! I'm back. I went down to the London launch as I was super excited to see the OnePlus 6 in person and I've now got my hands on the phone and the official tempered glass. So as I have done every year, I'm going to be testing out as many accessories that I can get my hands on, starting with the Official Tempered Glass Screen Protector!
Feel free to watch the video to get all this information, or just scroll down and read it if you prefer!
Some of you wonder why take of the pre-applied factory screen? Well for me, it's all about finding the best protection for your device and from experience the pre-applied screen is not that. It's a nice bonus, as if you're not buying the official you'll have to wait around a week or so before third party manufacturers get screens ready for sale. Mine was also riding slightly high on the screen, which meant using it whilst having gestures turned on was a bit of a nightmare.
As usual the screen protector, comes well packaged, with some excellent tools- most of which you won't need if you're taking the pre-applied screen off and then putting this one on straight away.
The screen protector as with the last few years comes on a single slab of plastic/glass, which you will need to be careful off when you're removing the screen protector from it. I've seen many people CRACK their screen protector at this point. Don't be that person! Go slow, but surely. And for goodness sake once you've peeled it off, don't turn it around and let all the dust particles in your house get on it!
The screen protector fits nicely on the phone and feels pretty decent. High quality!
Postives -
- Feels good
- Looks good
- Fits with the free case
Negatives -
- Finger print magnet - seriously, had it on for a few minutes and it was covered.
- Still has the black border, so you DO still get a 3D effect where you're missing an (admittedly small) portion of your screen
- Hardest OP screen protector I've ever put on.
Let me know if you have any questions on it, and I'll endeavor to keep you all updated on how it functions!
Thanks!
^ Dang! I can't believe how difficult it was for him to remove the bubbles with that protector. And in the end it still had a bubble that kept returning. This sure did make me glad I opted not to pay extra for that tempered glass protector. It's almost as if it doesn't have strong enough adhesive.
Regardless, I plan on sticking with the pre-applied screen protector for a bit before making a decision on a glass protector. In fact, if the pre-applied protector holds up well, I may not ever bother taking it off. I must say that it would be really nice to finally get a phone and never even worry about spending money on a screen protector, or trying to perfectly apply one, for that matter.
I just hope my pre-applied protector isn't positioned too high, as the above video reviewer mentioned his was.
unfortunately my preapplied screen protector is a tiny bit too high for my taste too, so when swiping up with gestures enabled you can feel the slight edge :/
I really hope whitedome is going to bring a TGSP for the OP6 on the market
niijonodhg said:
Here take a look at this. I''ve just posted it to the official forums to I'll C+P here;
----
Hi all,
Hope you've not forgotten me! I'm back. I went down to the London launch as I was super excited to see the OnePlus 6 in person and I've now got my hands on the phone and the official tempered glass. So as I have done every year, I'm going to be testing out as many accessories that I can get my hands on, starting with the Official Tempered Glass Screen Protector!
Feel free to watch the video to get all this information, or just scroll down and read it if you prefer!
Some of you wonder why take of the pre-applied factory screen? Well for me, it's all about finding the best protection for your device and from experience the pre-applied screen is not that. It's a nice bonus, as if you're not buying the official you'll have to wait around a week or so before third party manufacturers get screens ready for sale. Mine was also riding slightly high on the screen, which meant using it whilst having gestures turned on was a bit of a nightmare.
As usual the screen protector, comes well packaged, with some excellent tools- most of which you won't need if you're taking the pre-applied screen off and then putting this one on straight away.
The screen protector as with the last few years comes on a single slab of plastic/glass, which you will need to be careful off when you're removing the screen protector from it. I've seen many people CRACK their screen protector at this point. Don't be that person! Go slow, but surely. And for goodness sake once you've peeled it off, don't turn it around and let all the dust particles in your house get on it!
The screen protector fits nicely on the phone and feels pretty decent. High quality!
Postives -
- Feels good
- Looks good
- Fits with the free case
Negatives -
- Finger print magnet - seriously, had it on for a few minutes and it was covered.
- Still has the black border, so you DO still get a 3D effect where you're missing an (admittedly small) portion of your screen
- Hardest OP screen protector I've ever put on.
Let me know if you have any questions on it, and I'll endeavor to keep you all updated on how it functions!
Thanks!
Click to expand...
Click to collapse
Thanks for this! Your videos are always great when it comes to these things. Keep up the great work!
Do you think the bit the pops up might simply be just because of the curvature of the screen towards the corner?
(curved screened phones are always a nightmare when it comes to putting screen protectors on). If the underside of the screen protector is curved aswell in order to fit the curved screen of the device, even a fraction of difference can cause these kinds of problems, whereas flat ones you can even get away with them positioned slightly off, and they will always sit down perfectly flat.
Can you confirm whether the curvature of the OnePlus 6's screen is just around the edges, or is it the whole of the front that is actually curved?
(If you see what I mean).
I could be wrong, but from what I can see on the video, it does almost look like it's the whole screen that is rounded and not just the edges (but it's hard to tell from a video, so can't know for sure)
sn0warmy said:
^ Dang! I can't believe how difficult it was for him to remove the bubbles with that protector. And in the end it still had a bubble that kept returning. This sure did make me glad I opted not to pay extra for that tempered glass protector. It's almost as if it doesn't have strong enough adhesive.
Regardless, I plan on sticking with the pre-applied screen protector for a bit before making a decision on a glass protector. In fact, if the pre-applied protector holds up well, I may not ever bother taking it off. I must say that it would be really nice to finally get a phone and never even worry about spending money on a screen protector, or trying to perfectly apply one, for that matter.
I just hope my pre-applied protector isn't positioned too high, as the above video reviewer mentioned his was.
Click to expand...
Click to collapse
My pre-applied protector only lasted an hour on mine. The edges don't stick enough to avoid random lint and dust from sliding just a bit underneath it. Also the swipe up gestures from the bottom of the phone feel weird as you bump the protector. I'm not sure but I think it's because the protector is a bit thick.
Sent from my ONEPLUS A6003 using Tapatalk
jlczl said:
My pre-applied protector only lasted an hour on mine. The edges don't stick enough to avoid random lint and dust from sliding just a bit underneath it. Also the swipe up gestures from the bottom of the phone feel weird as you bump the protector. I'm not sure but I think it's because the protector is a bit thick.
Sent from my ONEPLUS A6003 using Tapatalk
Click to expand...
Click to collapse
That’s a shame. My phone arrives today and we leave for Mexico tomorrow for a week. I was hoping the pre-applied protector would be perfect. The edges of it are probably going to look like garbage by the time we get back.
the protective film, can not attach clean and then Euro 22, so I can not recommend. Shade for the money
unix2208 said:
the protective film, can not attach clean and then Euro 22, so I can not recommend. Shade for the money
Click to expand...
Click to collapse
What?
I really like the TGP. It fits seamlessly with the nylon case where the edges go all the way to the case and it feels completely natural. I thought the black outlining would bother me, but it works really well with the phone. I highly recommend the OEM TGP. No issues with it being compatible with the bumper case.
I have read on a Dutch forum that there is only glue on the edges of the screen protector. The middle is coated with some sort of oil so you won't see any bubbles.
This would explain the YouTube video with the corner not sticking. Could somebody confirm this?
This is a problem with all "curved edge" phones. Really makes me wish Samsung did not have as much sway in the market as they do. We would still have flat screens!
JCreations said:
I have read on a Dutch forum that there is only glue on the edges of the screen protector. The middle is coated with some sort of oil so you won't see any bubbles.
This would explain the YouTube video with the corner not sticking. Could somebody confirm this?
Click to expand...
Click to collapse
Sent from my Pixel 2 using Tapatalk
suprstar29 said:
I really like the TGP. It fits seamlessly with the nylon case where the edges go all the way to the case and it feels completely natural. I thought the black outlining would bother me, but it works really well with the phone. I highly recommend the OEM TGP. No issues with it being compatible with the bumper case.
Click to expand...
Click to collapse
More importantly, how difficult was it to get a bubble free install?
JCreations said:
I have read on a Dutch forum that there is only glue on the edges of the screen protector. The middle is coated with some sort of oil so you won't see any bubbles.
This would explain the YouTube video with the corner not sticking. Could somebody confirm this?
Click to expand...
Click to collapse
The tempered glass screen protector from OnePlus has adhesive throughout the entire protector, not just around the sides. Watch an install video and you'll see.
sn0warmy said:
More importantly, how difficult was it to get a bubble free install?
Click to expand...
Click to collapse
It wasn't to bad. There were a couple of stubborn small bubbles, but it you press and hold on them for a second or two with the included tool they go right away. I have a completely bubble free TGP that took maybe 2 minutes to put on
suprstar29 said:
It wasn't to bad. There were a couple of stubborn small bubbles, but it you press and hold on them for a second or two with the included tool they go right away. I have a completely bubble free TGP that took maybe 2 minutes to put on
Click to expand...
Click to collapse
Well crap. Now I wish I went ahead and ordered the protector with the phone. Now I've got to get through a week in Mexico with the pre-applied protector and hope it doesn't peel up until I get back.
Ordering the TGSP from OnePlus right now. Thanks for your input.
Just installed it and it looks great in my opinion! Wasn't that hard. If you apply it with the included case on, it helps a ton with lining it up; you literally just need to drop it into place.
I did get a couple pieces of dust underneath but they are super small and hardly noticeable, so I don't want to risk lifting the protector to remove it (risking more dust to get under) (or risking losing adhesion).
It does have a bit of that "3D look" but I got used to it very quick and now I don't notice it.
If there is text way at the edge of the screen, it does slightly get cut off but luckily most apps/websites don't have text that close to the edge.
Overall it's a solid protector and I'm probably going to stick with it until the end of its life (unless it cracks or something of course lol).