Hello
I decided to try jedi master x2 (the version of my stock ROM was 4.3). After trying it out for a while I noticed poor battery performance and when phone was locked I had to press the menu button several times to see the screen. Yesterday my phone was booting up by itself. It did a couple times then got stuck with the samsung logo. Reboot again and again and the same stuff happened that's when I decided to flash stock rom from samsung.updates/device site using odin3 v3.09 however, I have not been successful. After it checks the md5 OK, it fails on the NAND write. Is it the case that the NAND memory is not unlocked? I am still able to boot into recovery though. I'd appreciate if anybody can land me a hand on how to flash stock rom on my device.
Thanks
** Update to the issue above 1/13/14 8:24 AM
I use ODIN 3.09 to upload the md5 I got from samsung.updates.com I get this:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T889UVUCMK7_T889TMBCMK7_T889UVUCMK7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I am able to boot into recovery mode. I have not tried to upload any other ROM to my sdcard and install it there. The stock ROM I had before was Android version 4.3.
I read this post http://forum.xda-developers.com/showthread.php?t=2470262&page=3
then I looked at my device and read the following:
custom binary download: Yes (1 counts)
current binary: custom
system status: custom
knox warranty void: 1 <--- I think that's the problem
As you may know knox is a security feature which helps you to securely separate your personal and professional data. Well, in my case is not helping at all.
Another question: How am I going to remove knox with my phone only able to get into recovery or download mode?
Hi there,sorry for my bad english i'm Indonesian
My Gnote N8000 upgrade via OTA Official to Kitkat
After few months it's okay,but once week ago My Gnote Restart when i'm using browser.
It's non root and non cwm installing
When i try to flash with Odin V 1.84,1.85,3.09 it's have a same,it's failed
I try to flash with :
Jellybean Stock Rom :
KIES_HOME_N8000XXBLJ9_N8000OXABLJ9_412156_REV00_user_low_ship.tar
Kitkat Stock Rom :
N8000XXUDNE5_N8000OLBDNE3_N8000DXUDND1_HOME.tar
This is in my result in My Fail odin :
Spoiler: my odin
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N8000XXUDNE5_N8000OLBDNE3_N8000DXUDND1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
When i try to get in to recovery mode its just restart again and Logo Samsung Galaxy Note 10
In downloading Mode :
Odin Mode
PRODUCT NAME : GT-N8000
CURRENT BINARY : SAMSUNG OFFICIAL
SYSTEM STATUS : OFFICIAL
RP SWREV : A2
I try anything,i read in xda dev,but just have a same result
Please Anyone can help me
thank you very much before
Regads
I have a friend's phone a SAMSUNG S6 (SM-G920P) that won't boot, because he took it to some phone repair shops that have messed it more than it already is. I have this on the boot screen :
Code:
Kernel is not seandroid enfrocing.
Custom binary is blocked by FRP lock.
The first thing I've done is download a stock rom : G920PVPU1AOCF_G920PSPT1AOCF_G920PVPU1AOCF_HOME.tar.md5 and I tried to flash it via ODIN3.10.6, but I keep getting a fail message :
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920PVPU1AOCF_G920PSPT1AOCF_G920PVPU1AOCF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And this on the phone :
Code:
SW REV. CHECK FAIL. DEVICE: 3, BINARY: 1
Then, after searching online for this problem, I found out that I've been using the wrong stock firmware. But there is no way for me to check the modem and bootloader version, I tried fastboot but it keeps waiting for the device. I tried SmartSwitch and Kies, then can't find my device, and when I try using the model number (SM-G920P) and the serial number which is the MEID I found in the download mode>Home button (only that with the barcode), I get that this S/N is invalid. I really don't know what to do next, and I wish that someone could help me.
Thanks a lot!
Downloaded last firmware and flashed it. All things working fine, thanks.
http://www.sammobile.com/firmwares/database/SM-G900P/
Hey guys, I just bought an SGS7 (SM-G930F), It was on 6.0 (ITV) firmware and I flashed 7.0 VAU (Vodafone) firmware thru ODIN.
ODIN showed a FAIL message and I got the "An error occurred..." message when trying to boot up again.
Current ODIN screen says
- SYSTEM STATUS: Custom
- FRP LOCK: OFF
- Secure Download: Enabled
- WARRANTY VOID: 0 (0x0000)
I'm pretty sure I messed up on the secure download part (I should've disabled). But now I think I'm bricked. Any ideas how to fix?
Make sure it is the G930F in download mode
Flash it again, make sure you are using ODIN 3.12.3 or newer, check the "Repartition" option in ODIN if changing CSC
*Detection* said:
Make sure it is the G930F in download mode
Flash it again, make sure you are using ODIN 3.12.3 or newer, check the "Repartition" option in ODIN if changing CSC
Click to expand...
Click to collapse
It is G930F in Download mode. I am using ODIN 3.12.10 from this thread. I have checked "Re-Partition" in ODIN.
Now ODIN is stuck in at "initialization".
This is my current ODIN log.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1210)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
Click to expand...
Click to collapse
Btw, for CSC, do I use CSC or HOME_CSC?
Tried using a different USB lead?
Use a different USB port on the PC too
Use CSC for changing CSC
Try flashing the original CSC again to make sure you can unbrick too
*Detection* said:
Tried using a different USB lead?
Use a different USB port on the PC too
Use CSC for changing CSC
Try flashing the original CSC again to make sure you can unbrick too
Click to expand...
Click to collapse
I've tried using another USB port and I got this
<ID:0/005> Odin engine v(ID:3.1210)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I'll try with the original firmware.
Btw, with Smart Switch (older version), "Emergency Software Recovery & Initialization" --> "Device Intialization" tab doesn't work. It says "SM-G930F does not support initializing".
Also want to add, on ODIN screen, it says
RP SWREV B: 1 K: 0 S: 0
Click to expand...
Click to collapse
Try a new USB lead
Flash the Marshmallow 6.0 firmware instead of 7.0
Use original CSC firmware from now on until we get the phone back up and running
*Detection* said:
Try a new USB lead
Flash the Marshmallow 6.0 firmware instead of 7.0
Use original CSC firmware from now on until we get the phone back up and running
Click to expand...
Click to collapse
I get the "USB device not recognized....previous device malfunctioned" message on Windows when I use a different USB cable.
monsieurazizx said:
I get the "USB device not recognized....previous device malfunctioned" message on Windows when I use a different USB cable.
Click to expand...
Click to collapse
Got any other cables?
Try using ODIN 3.12.3 or 3.12.7 too
Got another PC you can use?
*Detection* said:
Got any other cables?
Try using ODIN 3.12.3 or 3.12.7 too
Got another PC you can use?
Click to expand...
Click to collapse
Tried with other cables and they all have the same error message.
I'll try a different PC and older ODIN versions now.
Using original firmware.
<ID:0/004> Odin engine v(ID:3.1210)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
Click to expand...
Click to collapse
It stopped at hidden.img
monsieurazizx said:
Using original firmware.
It stopped at hidden.img
Click to expand...
Click to collapse
Could try this
https://forum.xda-developers.com/galaxy-s6-edge/help/odin-fail-hidden-img-t3154903
*Detection* said:
Could try this
https://forum.xda-developers.com/galaxy-s6-edge/help/odin-fail-hidden-img-t3154903
Click to expand...
Click to collapse
Extracted hidden.img and renamed it to hidden.img.tar, then flashed as AP.
<ID:0/004> Odin engine v(ID:3.1210)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> :ÿ&í
<ID:0/004> Unassigned file
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1
Click to expand...
Click to collapse
I tried again with the CSC. Now it stopped at a different part.
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> cache.img
<ID:0/004> __XmitData_Write
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I'll reply if I have any other ideas, last thing I can think for now is to flash AP only and see how you get on with that
Hello,
I recently tried to install a ROM on a Samsung galaxy s6 (SM-G920F) while following a guide. The guide said to reset to factory settings and to wipe the cache, which i did.
The custom ROM i tried to install didn't work, and now i have an error message when trying to turn the phone on. It says "An error has occured while updating the device software. Use the Emergency recovery function in the Smart Switch PC software"
I tried to flash stock firmware onto the phone that i downloaded from sammobile.com, but this doesn't seem to work.
I select the .tar.md5 file with the AP button in Odin3 v3.13 and hit Start once it allows me. It fails near the end, this is in the log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 3740 M
<ID:0/006> SetupConnection..
<ID:0/006> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
I also tried to install this Smart Switch PC software, but cannot find it anywhere. EDIT: Found it now, but couldn't install it. Translated the message says: Application cannot be started because the configuration next to each other is wrong.
Can anyone please tell me what i'm doing wrong? I really need to get the phone back in working order.
EDIT: It was getting much further through the flash when i tried it yesterday, looked like it was about 90% done before it failed. Now it doesn't even properly start. The Odin log i posted is one from today.
EDIT2: The information at the top of the download screen is as follows:
odin mode
product name: sm-g920f
current binary: Samsung Official
system status: official
reactivation lock: off
secure download: enabled
knox warranty void: 0 (0x0000)
rp swrev: B:6 K:2 S:2
SW REV. Check fail. Device: 6. Binary: 4
EDIT3: tried to run a flash again, it failed at the same point it did yesterday. the log:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 3712 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> cm.bin
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img
<ID:0/006> cache.img
<ID:0/006> hidden.img
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Managed to fix my issue through following the steps on this post:
https://forum.xda-developers.com/showpost.php?p=66418660&postcount=25