Cannot flash stock firmware? - Galaxy S6 Q&A, Help & Troubleshooting

Cannot flash stock firmware? - Galaxy S6 Q&A, Help & Troubleshooting

Hello,
I recently tried to install a ROM on a Samsung galaxy s6 (SM-G920F) while following a guide. The guide said to reset to factory settings and to wipe the cache, which i did.
The custom ROM i tried to install didn't work, and now i have an error message when trying to turn the phone on. It says "An error has occured while updating the device software. Use the Emergency recovery function in the Smart Switch PC software"
I tried to flash stock firmware onto the phone that i downloaded from sammobile.com, but this doesn't seem to work.
I select the .tar.md5 file with the AP button in Odin3 v3.13 and hit Start once it allows me. It fails near the end, this is in the log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 3740 M
<ID:0/006> SetupConnection..
<ID:0/006> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
I also tried to install this Smart Switch PC software, but cannot find it anywhere. EDIT: Found it now, but couldn't install it. Translated the message says: Application cannot be started because the configuration next to each other is wrong.
Can anyone please tell me what i'm doing wrong? I really need to get the phone back in working order.
EDIT: It was getting much further through the flash when i tried it yesterday, looked like it was about 90% done before it failed. Now it doesn't even properly start. The Odin log i posted is one from today.
EDIT2: The information at the top of the download screen is as follows:
odin mode
product name: sm-g920f
current binary: Samsung Official
system status: official
reactivation lock: off
secure download: enabled
knox warranty void: 0 (0x0000)
rp swrev: B:6 K:2 S:2
SW REV. Check fail. Device: 6. Binary: 4
EDIT3: tried to run a flash again, it failed at the same point it did yesterday. the log:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 3712 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> cm.bin
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img
<ID:0/006> cache.img
<ID:0/006> hidden.img
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Managed to fix my issue through following the steps on this post:
https://forum.xda-developers.com/showpost.php?p=66418660&postcount=25

Related

Help s3 gt i9300

So I rooted and rom my galaxy note just fine even help a friend to recover his note 2.
But another friend try to root or place a rom on his S3 I dont know really and now the samsung galaxy sIII gt I9300 is stock on that logo.
So far I've try the following
Odin3 v3.07
philz_touch_6.07.9-i9300.tar.md5
I get:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.07.9-i9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1
odin3 v1.85.exe
CF-Root-SG3-V6.1.TAR
DRIVER SW installation is ok
I get:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> recovery.img
<ID:0/007> NAND Write Start!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
odin3 v3.07
I9300UBELL6_I9300UBELL1_I9300CRCELL_1HOME.tar.md5
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBELL6_I9300UBELL1_I9300CRCELL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I had try this one from xda as well:
- Unzip the attached Odin3-vX.X.zip file
- Download and unzip the CF-Auto-Root-....zip file (see posts below this one)
- If you end up with a recovery.img and cache.img file, you've extracted twice. You need to end up with a .tar.md5 file - don't extract that one
- (USB) Disconnect your phone from your computer
- Start Odin3-vX.X.exe
- Click the PDA button, and select CF-Auto-Root-....tar.md5
- Put your phone in download mode (turn off phone, then hold VolDown+Home+Power to boot - if it asks you to press a button to continue, press the listed button, or run adb reboot download command)
- (USB) Connect the phone to your computer
- Make sure Repartition is NOT checked
- Click the Start button
- Wait for Android to boot
- Done (if it took you more than 30 seconds, you need practise!)
- NOTE: Sometimes the device does *not* boot into recovery mode and root your device. Just do the entire procedure again if this happens. If it still will not install root and such, make sure that in Odin "Auto Reboot" is not checked. Then after flashing, pull the battery, and boot with VolUp+Home+Power button to boot into recovery manually. This will start the install process.
But this last doesn’t work either…

Choko888 said:
So I rooted and rom my galaxy note just fine even help a friend to recover his note 2.
But another friend try to root or place a rom on his S3 I dont know really and now the samsung galaxy sIII gt I9300 is stock on that logo.
So far I've try the following
Odin3 v3.07
philz_touch_6.07.9-i9300.tar.md5
I get:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.07.9-i9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1
odin3 v1.85.exe
CF-Root-SG3-V6.1.TAR
DRIVER SW installation is ok
I get:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> recovery.img
<ID:0/007> NAND Write Start!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
odin3 v3.07
I9300UBELL6_I9300UBELL1_I9300CRCELL_1HOME.tar.md5
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBELL6_I9300UBELL1_I9300CRCELL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I had try this one from xda as well:
- Unzip the attached Odin3-vX.X.zip file
- Download and unzip the CF-Auto-Root-....zip file (see posts below this one)
- If you end up with a recovery.img and cache.img file, you've extracted twice. You need to end up with a .tar.md5 file - don't extract that one
- (USB) Disconnect your phone from your computer
- Start Odin3-vX.X.exe
- Click the PDA button, and select CF-Auto-Root-....tar.md5
- Put your phone in download mode (turn off phone, then hold VolDown+Home+Power to boot - if it asks you to press a button to continue, press the listed button, or run adb reboot download command)
- (USB) Connect the phone to your computer
- Make sure Repartition is NOT checked
- Click the Start button
- Wait for Android to boot
- Done (if it took you more than 30 seconds, you need practise!)
- NOTE: Sometimes the device does *not* boot into recovery mode and root your device. Just do the entire procedure again if this happens. If it still will not install root and such, make sure that in Odin "Auto Reboot" is not checked. Then after flashing, pull the battery, and boot with VolUp+Home+Power button to boot into recovery manually. This will start the install process.
But this last doesn’t work either…
Click to expand...
Click to collapse
Which firmware version is actually installed on the S3 ?

firmware
LS.xD said:
Which firmware version is actually installed on the S3 ?
Click to expand...
Click to collapse
I dont know I got the phone only with de dowload option available, but I think should be
PDA: I9300UBEMH2
CSC: I9300ICEEMH1
MODEM: I9300UBEMH1

Choko888 said:
I dont know I got the phone only with de dowload option available, but I think should be
PDA: I9300UBEMH2
CSC: I9300ICEEMH1
MODEM: I9300UBEMH1
Click to expand...
Click to collapse
Use this CF-AUTO-ROOT --> LINK
and the latest TWRP --> LINK
or the latest PhilZ CWM --> LINK
idk where you got your files from, but they are out of date...

LS.xD said:
Use this CF-AUTO-ROOT -->
and the latest TWRP -->
or the latest PhilZ CWM -->
idk where you got your files from, but they are out of date...
Click to expand...
Click to collapse
with the CF auto root I get:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-m0-m0xx-gti9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
and If I try philz
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.26.6-i9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
twrp:
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)

Have you tried flashing stock firmware first?
Sent from my beloved HTC One S using (most time buggy) Tapatalk

Good

I try to download at sammobile but it doesn't allow me ...
Sent from my GT-N7000 using XDA Free mobile app

Choko888 said:
I try to download at sammobile but it doesn't allow me ...
Sent from my GT-N7000 using XDA Free mobile app
Click to expand...
Click to collapse
use samsung-updates.com instead

LS.xD said:
use samsung-updates.com instead
Click to expand...
Click to collapse
Thanks I think I left one downloading last night I hope its the same one in samsung updates as soon as I get out of work. I´ try it.

LS.xD said:
use samsung-updates.com instead
Click to expand...
Click to collapse
Now I have a doubt, samsung-updates shows CRC (my country)
Galaxy S 3 (International)GT-I9300 CRC I9300UBELL6 4.1.2 31.12.2012 767276 and the information I pull from sammobile said this
Galaxy S 3 (International)GT-I9300 CRC I9300UBEMH2 and samsung updates doesnt have my country code with the same PDA as sammobile.
Do you think samsung-updates has a diferent code for my country? What should I do? Wich one should I pick ?

Choko888 said:
Now I have a doubt, samsung-updates shows CRC (my country)
Galaxy S 3 (International)GT-I9300 CRC I9300UBELL6 4.1.2 31.12.2012 767276 and the information I pull from sammobile said this
Galaxy S 3 (International)GT-I9300 CRC I9300UBEMH2 and samsung updates doesnt have my country code with the same PDA as sammobile.
Do you think samsung-updates has a diferent code for my country? What should I do? Wich one should I pick ?
Click to expand...
Click to collapse
Which firmware is actually installed?

LS.xD said:
Which firmware is actually installed?
Click to expand...
Click to collapse
I dont know I got the phone only with de dowloading option available, Where can I see it if this is the only state of the phone?...

So try the one I think it was for my country I9300UBEMH2_I9300ICEEMH1_ICE but I get
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBEMH2_I9300UBEMH1_I9300ICEEMH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Since it is international version I try with some firmwares from germany , uk and rusia but it did work either

[Q]Gnote 10 N8000 Kitkat Official Bootloop cant flash odin

Hi there,sorry for my bad english i'm Indonesian
My Gnote N8000 upgrade via OTA Official to Kitkat
After few months it's okay,but once week ago My Gnote Restart when i'm using browser.
It's non root and non cwm installing
When i try to flash with Odin V 1.84,1.85,3.09 it's have a same,it's failed
I try to flash with :
Jellybean Stock Rom :
KIES_HOME_N8000XXBLJ9_N8000OXABLJ9_412156_REV00_user_low_ship.tar
Kitkat Stock Rom :
N8000XXUDNE5_N8000OLBDNE3_N8000DXUDND1_HOME.tar
This is in my result in My Fail odin :
Spoiler: my odin
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N8000XXUDNE5_N8000OLBDNE3_N8000DXUDND1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
When i try to get in to recovery mode its just restart again and Logo Samsung Galaxy Note 10
In downloading Mode :
Odin Mode
PRODUCT NAME : GT-N8000
CURRENT BINARY : SAMSUNG OFFICIAL
SYSTEM STATUS : OFFICIAL
RP SWREV : A2
I try anything,i read in xda dev,but just have a same result
Please Anyone can help me
thank you very much before
Regads

[Resolved][S6 SM-G920P won't boot] Kernel & Binary problems

I have a friend's phone a SAMSUNG S6 (SM-G920P) that won't boot, because he took it to some phone repair shops that have messed it more than it already is. I have this on the boot screen :
Code:
Kernel is not seandroid enfrocing.
Custom binary is blocked by FRP lock.
The first thing I've done is download a stock rom : G920PVPU1AOCF_G920PSPT1AOCF_G920PVPU1AOCF_HOME.tar.md5 and I tried to flash it via ODIN3.10.6, but I keep getting a fail message :
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920PVPU1AOCF_G920PSPT1AOCF_G920PVPU1AOCF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And this on the phone :
Code:
SW REV. CHECK FAIL. DEVICE: 3, BINARY: 1
Then, after searching online for this problem, I found out that I've been using the wrong stock firmware. But there is no way for me to check the modem and bootloader version, I tried fastboot but it keeps waiting for the device. I tried SmartSwitch and Kies, then can't find my device, and when I try using the model number (SM-G920P) and the serial number which is the MEID I found in the download mode>Home button (only that with the barcode), I get that this S/N is invalid. I really don't know what to do next, and I wish that someone could help me.
Thanks a lot!

Downloaded last firmware and flashed it. All things working fine, thanks.
http://www.sammobile.com/firmwares/database/SM-G900P/

[Help] Galaxy S 6 G920W8 stuck on SAMSUNG logo during boot

So I have a samsung Galaxy S 6 (G920W8) that I cannot get to boot into Android.
I was able to get the device into recovery and download mode, and I'm able to install TWRP on the device, boots into that with zero problems.
I've been able to use TWRP to install custom ROMs and kernels, and I can use an older version of ODIN to flash the correct carrier ROM to the phone, but newer version fail on the NAND WRITE step. TWRP gives no errors when attempting to flash, and I have access to the whole memory of the device.
Is there any hope for this device?

Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920W8VLU3BOL1_G920W8OYA3BOL1_G920W8VLU3BOL1_HOME.tar.md5 is invalid.
<OSM> End...
<Accidentally tried adding file before it was done unzipping>
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> cache.img
<ID:0/005> modem.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
That's the result in Odin after trying to flash that carrier ROM with Odin3 v3.10.7. Now the device is still boot looping. I don't understand what's wrong.

DisturbenChamp said:
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920W8VLU3BOL1_G920W8OYA3BOL1_G920W8VLU3BOL1_HOME.tar.md5 is invalid.
<OSM> End...
<Accidentally tried adding file before it was done unzipping>
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> cache.img
<ID:0/005> modem.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
That's the result in Odin after trying to flash that carrier ROM with Odin3 v3.10.7. Now the device is still boot looping. I don't understand what's wrong.
Click to expand...
Click to collapse
Boot into recovery and factory reset.
Sent from my SM-G925F

Rosli59564 said:
Boot into recovery and factory reset.
Sent from my SM-G925F
Click to expand...
Click to collapse
I have tried that. The device continues to boot loop, even when wiped through official recovery or TWRP recovery.

DisturbenChamp said:
I have tried that. The device continues to boot loop, even when wiped through official recovery or TWRP recovery.
Click to expand...
Click to collapse
Try to reinitialize the phone with smart switch. Maybe it's the firmware you flashed with odin.
Sent from my SM-G925F

Rosli59564 said:
Try to reinitialize the phone with smart switch. Maybe it's the firmware you flashed with odin.
Sent from my SM-G925F
Click to expand...
Click to collapse
Smart Switch nor Kies will connect to the device., but odin and MTP via TWRP both work. I've attempted a 5.0.2 and 5.1.1 ROM from the carrier, the ROMs are from Sam-Firmware, and I am currently downloading a 6.0.1 file to attempt and flash..
Sometimes in Download mode it displays the following error:
Code:
SW REV CHECK FAIL. DEVICE: 3, BINARY: 1
OR
SW REV CHECK FAIL. DEVICE: 3, BINARY: 2

Samsung S6 (SM-G920F) Bootloop / Flash fail.

Hello there!
My phone is in Bootloop and i'm trying to flash the original firmware with Odin, but i'm getting an fail:
Odin error:
<ID:0/006> Removed!!
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1205)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
<ID:0/006> cache.img
<ID:0/006> cm.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Phone error:
[CM] SW REV. check fail device: 5, binary 3
I'm from Netherlands, with an unlocked phone but i'm Using Vodafone as a provider.
Can someone please help me in the right direciton.
thanks in advance!
EDIT: Fixed the problem myself
for those wanne know how: I tried to flash a different firmware and that worked.

bro try a firmware with 4 files just google it

Database Info

welcome

Cannot flash stock firmware? - Galaxy S6 Q&A, Help & Troubleshooting

Managed to fix my issue through following the steps on this post: https://forum.xda-developers.com/showpost.php?p=66418660&postcount=25

Related

Help s3 gt i9300

[Q]Gnote 10 N8000 Kitkat Official Bootloop cant flash odin

[Resolved][S6 SM-G920P won't boot] Kernel & Binary problems

[Help] Galaxy S 6 G920W8 stuck on SAMSUNG logo during boot

Samsung S6 (SM-G920F) Bootloop / Flash fail.

Categories

Resources