When update to MIUI 8 the phone restart then it wont boot up. I update via fastboot. I already send to XiaoMi center they say they also cannot reflash the rom need to put there and maybe need to change the mother board. By this cost I can buy another new phone so is there any way to fix the XiaoMi Mi4i ?
No light when charging.
No recovery menu ( Power + Volume Up )
No Fastboot ( Power + Volume Down )
Have you tried to put the device in QDL_9008 Mode? If it works, there is hope
Hackerpunk1 said:
Have you tried to put the device in QDL_9008 Mode? If it works, there is hope
Click to expand...
Click to collapse
In my laptop I found that in the Device Management. So what can I do ?
Can I charge the phone is the phone is bricked ? I scare that the battery will run out.
ic3tea said:
In my laptop I found that in the Device Management. So what can I do ?
Can I charge the phone is the phone is bricked ? I scare that the battery will run out.
Click to expand...
Click to collapse
If you can go to EDL
Use miflash to flash the latest firmware
Leave the phone to charge for about 30min, then try to flash the device, this will ensure that you battery won't die during the flash.
faizauthar12 said:
If you can go to EDL
Use miflash to flash the latest firmware
Click to expand...
Click to collapse
What do you mean by ELD ?
Hackerpunk1 said:
Leave the phone to charge for about 30min, then try to flash the device, this will ensure that you battery won't die during the flash.
Click to expand...
Click to collapse
So no LED light the phone will charge also ?
ic3tea said:
What do you mean by ELD ?
So no LED light the phone will charge also ?
Click to expand...
Click to collapse
ELD = Emergency Download Mode
Just don't worry about the led, just leave it
Hackerpunk1 said:
ELD = Emergency Download Mode
Just don't worry about the led, just leave it
Click to expand...
Click to collapse
Oh then how to enter EDL and what should I do ?
Related
My brother's htc sensation xe mob turned of suddenly and when tried to turn on mob it din't give anything only the soft button light and screen black .. he was using viper rom ..any idea about what happen with mob? P.s when i connect the mob to pc it give android phone but with yellow triangle and when try volume down with power button not give anyyhing too and soft button turn on and off simultaneously and when plug the charger while tge phone is off the led lamp give orange light for a sec then turn off again see screenshot
Ahmed.ragab said:
My brother's htc sensation xe mob turned of suddenly and when tried to turn on mob it din't give anything only the soft button light and screen black .. he was using viper rom ..any idea about what happen with mob? P.s when i connect the mob to pc it give android phone but with yellow triangle and when try volume down with power button not give anyyhing too and soft button turn on and off simultaneously and when plug the charger while tge phone is off the led lamp give orange light for a sec then turn off again see screenshot
Click to expand...
Click to collapse
I think luckily u havn't brick ur device.It is a hardware problem.
remove the battery and put it back
then try to boot into bootloader
if you boot select reboot
rzr86 said:
remove the battery and put it back
then try to boot into bootloader
if you boot select reboot
Click to expand...
Click to collapse
I can't boot into bootloader when i try thr soft key turn on and off simultaneously and screen is dark P.s (my brother put it in his pocket then he get it out to see it like that ? I thought maybe there is something wrong with screen but i tried to open mob normally till the soft key became light and never turn off then tried to make make a call to see if the mob will ring it said the mob is closed so i think this isn't about the screen any Idea ?
Any Idea ?
the 1st screenshot is when i connect my mob to the charger only soft key light on and never off
the 2nd screenshot is when I connected my mob to the pc and try to go to bootlooder with ADB
the 3rd screenshot is when i try to connect it with KGS utility (in all cases screen is always black)
Ahmed.ragab said:
Any Idea ?
the 1st screenshot is when i connect my mob to the charger only soft key light on and never off
the 2nd screenshot is when I connected my mob to the pc and try to go to bootlooder with ADB
the 3rd screenshot is when i try to connect it with KGS utility (in all cases screen is always black)
Click to expand...
Click to collapse
in adb mode your device is being recognized
when you are entering adb reboot bootloader what happens?
rzr86 said:
in adb mode your device is being recognized
when you are entering adb reboot bootloader what happens?
Click to expand...
Click to collapse
Nothing happen it's like the SS
Ahmed.ragab said:
Nothing happen it's like the SS
Click to expand...
Click to collapse
did you try to boot into safe mode?
rzr86 said:
did you try to boot into safe mode?
Click to expand...
Click to collapse
I can't boot into safe mode .. screen light never turned on and when i try to switch on mob normally thr green light turn on then turn off again and the mob vibrate and the soft key light always turn on anf after while it turn off and by just preesing volume up otlr power button it light again
Ahmed.ragab said:
I can't boot into safe mode .. screen light never turned on and when i try to switch on mob normally thr green light turn on then turn off again and the mob vibrate and the soft key light always turn on anf after while it turn off and by just preesing volume up otlr power button it light again
Click to expand...
Click to collapse
did you try to use a ruu.exe?
i am thinking that it could be a hardware issue
rzr86 said:
did you try to use a ruu.exe?
i am thinking that it could be a hardware issue
Click to expand...
Click to collapse
I'm trying to charge my battery more than 30 % cause he don't wanna continue installing and i have a slow external charger and will back to you again
It say rebooting to bootloader and stop in this stage see the SS
Ahmed.ragab said:
I'm trying to charge my battery more than 30 % cause he don't wanna continue installing and i have a slow external charger and will back to you again
It say rebooting to bootloader and stop in this stage see the SS
Click to expand...
Click to collapse
i don't know what to suggest anymore mate
probably it is hardware
rzr86 said:
i don't know what to suggest anymore mate
probably it is hardware
Click to expand...
Click to collapse
but do u think if it is a hardware it would read as android phone on pc normally but can't restart to bootloader ?
Ahmed.ragab said:
but do u think if it is a hardware it would read as android phone on pc normally but can't restart to bootloader ?
Click to expand...
Click to collapse
maybe some partition is damaged
rzr86 said:
maybe some partition is damaged
Click to expand...
Click to collapse
so how to repair this partitions ?
Ahmed.ragab said:
so how to repair this partitions ?
Click to expand...
Click to collapse
i really don't know mate
search here in xda
maybe you will find something about it
edit: did you try the unbricking project?
otherwise see this thread
http://forum.xda-developers.com/showthread.php?t=2775115
rzr86 said:
i really don't know mate
search here in xda
maybe you will find something about it
edit: did you try the unbricking project?
otherwise see this thread
http://forum.xda-developers.com/showthread.php?t=2775115
Click to expand...
Click to collapse
i tried unbricking project but ubuntu can't recognize my mob in QHSUSB_DLOAD mod without battery And ubuntu can't recognize my mob totally
rashmifantasy said:
I think luckily u havn't brick ur device.It is a hardware problem.
Click to expand...
Click to collapse
rzr86 said:
remove the battery and put it back
then try to boot into bootloader
if you boot select reboot
Click to expand...
Click to collapse
rzr86 said:
i really don't know mate
search here in xda
maybe you will find something about it
edit: did you try the unbricking project?
otherwise see this thread
http://forum.xda-developers.com/showthread.php?t=2775115
Click to expand...
Click to collapse
I repaired it guys the problem was with the lcd screen I replaced my sensation xe screen with my friends's sensation and it is working good now
Yesterday, I was playing on my phone. Suddenly, it switch off. I thought it was out of battery so i plugged the charger and left there till morning. But until this morning I cant switch on my phone. What should I do? BTW the led shows orange and gone when I plugged the charger.
wilsonkok19996 said:
Yesterday, I was playing on my phone. Suddenly, it switch off. I thought it was out of battery so i plugged the charger and left there till morning. But until this morning I cant switch on my phone. What should I do? BTW the led shows orange and gone when I plugged the charger.
Click to expand...
Click to collapse
remove battery,sdcard and sim
charge the device as it is for 4-5 hours
put them back and switch it on
see if it boots
rzr86 said:
remove battery,sdcard and sim
charge the device as it is for 4-5 hours
put them back and switch it on
see if it boots
Click to expand...
Click to collapse
ok ... now I try. What should i do if cant?
wilsonkok19996 said:
ok ... now I try. What should i do if cant?
Click to expand...
Click to collapse
try this
http://forum.xda-developers.com/showthread.php?t=1522351
rzr86 said:
try this
http://forum.xda-developers.com/showthread.php?t=1522351
Click to expand...
Click to collapse
Does that mean i need to format my phone?
wilsonkok19996 said:
Does that mean i need to format my phone?
Click to expand...
Click to collapse
yes if you succeed with unbricking project you have to flash a RUU.exe after that
rzr86 said:
yes if you succeed with unbricking project you have to flash a RUU.exe after that
Click to expand...
Click to collapse
I think is not about the brick problem. I think is the phone cant detect a battery with 0% of power. But still I followeed ur step but wont worked. Do ypu have other method?
wilsonkok19996 said:
I think is not about the brick problem. I think is the phone cant detect a battery with 0% of power. But still I followeed ur step but wont worked. Do ypu have other method?
Click to expand...
Click to collapse
i don't know any other way
you have to switch on somehow the device
when you press power button does it respond at all?
rzr86 said:
i don't know any other way
you have to switch on somehow the device
when you press power button does it respond at all?
Click to expand...
Click to collapse
I tried but the screen had not any reaction. It seems like my phone wont charge the battery after shut down.
Can someone give me some instructions how to fix bootloop using PC? It would be a great help to all of us Thanks in advance more power!
What happened before this bootlooping?
kdd998 said:
What happened before this bootlooping?
Click to expand...
Click to collapse
My rom before that is Project Spectrum then I want to go back to ColorOS since it has so many bugs then it bootlooped
you need a working recovery. Once off, try to use volume UP and power at the same time.
kdd998 said:
you need a working recovery. Once off, try to use volume UP and power at the same time.
Click to expand...
Click to collapse
I already tried but nothing happened ?
And with volume down?
I made a mistake:*volume up is for fastboot (when enabled), down for recovery.
You might have to try power during 15*seconds before. And do not plug your phone.
kdd998 said:
And with volume down?
I made a mistake:*volume up is for fastboot (when enabled), down for recovery.
You might have to try power during 15*seconds before. And do not plug your phone.
Click to expand...
Click to collapse
Nothing happened also I dont know what to do
Anything appearing on your computer when you plug USB?
kdd998 said:
Anything appearing on your computer when you plug USB?
Click to expand...
Click to collapse
Yes it recognize my phone
help !
my f1s isnt recognised by usb.......stuck in bootloop. no recovery.... HELPPPP
Hi gang,
My Xperia Z5 (E6603) would not boot up after the latest update. I'm guessing it must've died during the update.
I tried:
Reset (Pwr + Vol+/-) and OFF button in sim card tray. All reset attempt was done several times with and without the simcard tray.
I noticed the phone did not vibrate when I tried Pwr + vol+ or with the OFF button by itself. It only vibrate when the OFF and Pwr button were held down simultaneously.
To rule out it was battery, I let it charged for almost 2 days now without any success. I still get the slow blinking red light and no solid red or orange or green light indicating the device is fully charged. I also check the integrity of the battery at the stored and it is at 4.0 V, so I believe the battery is not the problem.
Unplugging battery method: Tried unplugging the battery and connect to the computer then plugged it back in with no luck.
Flashtool was not recognized after holding Vol- and connect to the computer.
I also tried different charger and usb
i read from many forum that the battery needs to die in order to reset the kernel. Should I just let the battery discharged? Or are there others ways that are more efficient?
I'm not sure what to do at this point. Any suggestion will be greatly appreciated.
Thank you!
try change battery
Alvian_P said:
try change battery
Click to expand...
Click to collapse
I believe the battery is ok. I brought it to the store to check the charge and it was sufficient
thank you,
Flash phone using Flashtool.
El Solido said:
Flash phone using Flashtool.
Click to expand...
Click to collapse
Unfortunately, the phone is not recognized by flashtool.
Thank you,
maybe bootloader corrupt. bootloader in emmc. try bring your phone to phone services, JTAG flash may help.
Alvian_P said:
maybe bootloader corrupt. bootloader in emmc. try bring your phone to phone services, JTAG flash may help.
Click to expand...
Click to collapse
What software can I use to fix the bootloader? I have an unlocked phone so my service provider will not take care of it.
Thank you!
myphonedied said:
What software can I use to fix the bootloader? I have an unlocked phone so my service provider will not take care of it.
Thank you!
Click to expand...
Click to collapse
Go to phone repair outlets in your city, not in Sony Service Center. usually they can fix hardware problem. I dont know what software are used. I only know with Jtag can repair bootloader via test point.
Alvian_P said:
Go to phone repair outlets in your city, not in Sony Service Center. usually they can fix hardware problem. I dont know what software are used. I only know with Jtag can repair bootloader via test point.
Click to expand...
Click to collapse
Does the bootloader need to be unlocked on the phone previously for the JTAG method to work?
Thank you for the suggestion,
myphonedied said:
Does the bootloader need to be unlocked on the phone previously for the JTAG method to work?
Thank you for the suggestion,
Click to expand...
Click to collapse
not sure. locked or unlocked should work, because the files inject directly to emmc
by the way, have you try to change another battery?
ave you tried to boot the phone into download mode?
Have you tried the actual Sony Tool and the Recovery-Process?
With that i unbricked my Z5 from that symptons i think 2 or 3 times already after the flash went somehow wrong because it stopped midway.
Alvian_P said:
not sure. locked or unlocked should work, because the files inject directly to emmc
by the way, have you try to change another battery?
Click to expand...
Click to collapse
I ordered a new battery, will try that and let you know
Thanks!
Seelbreaker said:
ave you tried to boot the phone into download mode?
Have you tried the actual Sony Tool and the Recovery-Process?
With that i unbricked my Z5 from that symptons i think 2 or 3 times already after the flash went somehow wrong because it stopped midway.
Click to expand...
Click to collapse
The phone won't boot into download mode. It's not recognized by PC companion so I can't carry out the recovery process.
Thank you for the suggestion!
myphonedied said:
I ordered a new battery, will try that and let you know
Thanks!
Click to expand...
Click to collapse
Ok... :good:
myphonedied said:
The phone won't boot into download mode. It's not recognized by PC companion so I can't carry out the recovery process.
Thank you for the suggestion!
Click to expand...
Click to collapse
Another thing - on my Laptop i can't access fastboot mode because it restarts everytime (showing the blue led and then it reboots), therefore i have to attach the Z5 to the Dockingstation.
But it seems like it is completeley dead right?
just to be sure - press and hold vol up and then connect your usb-cable. If the LED stays blue - gg
Then you just have to install the fastboot driver in Test-Mode (reboot to f8 and deactivate the Enforced Driver Signature) and then you may be able to atleast flash or better first boot the phone with a new kernel. If the boot works and then crashes you have your first step to unbrick the phone.
fastboot boot "kernel-image"
Altough i don't have any idea which Kernel you should choose
Seelbreaker said:
Another thing - on my Laptop i can't access fastboot mode because it restarts everytime (showing the blue led and then it reboots), therefore i have to attach the Z5 to the Dockingstation.
But it seems like it is completeley dead right?
just to be sure - press and hold vol up and then connect your usb-cable. If the LED stays blue - gg
Then you just have to install the fastboot driver in Test-Mode (reboot to f8 and deactivate the Enforced Driver Signature) and then you may be able to atleast flash or better first boot the phone with a new kernel. If the boot works and then crashes you have your first step to unbrick the phone.
fastboot boot "kernel-image"
Altough i don't have any idea which Kernel you should choose
Click to expand...
Click to collapse
Red blinking red in Sony phones mean bricked motherboard
Try on different computer. Use USB 2.0 port and original sony cable.
EugenStanis said:
Red blinking red in Sony phones mean bricked motherboard
Click to expand...
Click to collapse
Any way to fix a bricked motherboard?
myphonedied said:
Any way to fix a bricked motherboard?
Click to expand...
Click to collapse
Yes, replacing it
Use setool2 box for unbreak your phone
I was using lrteam twrp 3.4.2b-1206 and I was sideloading the vendor update for 12.2.1.0 when the progress bar froze. I gave it 10 minutes and held the power button to reboot and now the phone is showing no signs of life i cant get it to even show the poco screen. I've got no ideas left on what to do.
ashawanz said:
I was using lrteam twrp 3.4.2b-1206 and I was sideloading the vendor update for 12.2.1.0 when the progress bar froze. I gave it 10 minutes and held the power button to reboot and now the phone is showing no signs of life i cant get it to even show the poco screen. I've got no ideas left on what to do.
Click to expand...
Click to collapse
Did you try holding power and volume down? Also charge it for some hours.
Tecardo said:
Did you try holding power and volume down? Also charge it for some hours.
Click to expand...
Click to collapse
yeah no combination of buttons will show any signs of life and i can't even get to the bootloader. It should be at 100% battery at this point i dont think that's the issue either
Where did you find vendor update for 12.2.1.0 ?
NOSS8 said:
Where did you find vendor update for 12.2.1.0 ?
Click to expand...
Click to collapse
Some users postet from Xiaomi firmware website (non official) . Link is in many rom threads
ashawanz said:
yeah no combination of buttons will show any signs of life and i can't even get to the bootloader. It should be at 100% battery at this point i dont think that's the issue either
Click to expand...
Click to collapse
Did you attach it to pc and see what device gets detected then? It could be in qualcomm usb mode
Tecardo said:
Some users postet from Xiaomi firmware website (non official) . Link is in many rom threads
Click to expand...
Click to collapse
Firmeware not vendor,not the same.
is the phone appear on pc?
Tecardo said:
Did you attach it to pc and see what device gets detected then? It could be in qualcomm usb mode
Click to expand...
Click to collapse
If the the phone appear in qualcom usb, flashing in EDL will be possible and requires an authorization that only official repairers have.
NOSS8 said:
Firmeware not vendor,not the same.
is the phone appear on pc?
Click to expand...
Click to collapse
as I remember it's included? Otherwise use Xiaomi eu rom. It's including vendor.
Tecardo said:
as I remember it's included? Otherwise use Xiaomi eu rom. It's including vendor.
Click to expand...
Click to collapse
My first question was for ashawanz" Where did you find vendor update for 12.2.1.0 ? "
and this answer" If the the phone appear in qualcom usb, flashing in EDL will be possible and requires an authorization that only official repairers have" was not intended for you 'my mistake' but still for ashawanz
ashawanz said:
yeah no combination of buttons will show any signs of life and i can't even get to the bootloader. It should be at 100% battery at this point i dont think that's the issue either
Click to expand...
Click to collapse
Where did you find vendor update for 12.2.1.0 ?
Firmeware not vendor,not the same.
is the phone appear on pc?
If the the phone appear in qualcom usb, flashing in EDL will be possible and requires an authorization that only official repairers have.
Tecardo said:
Did you attach it to pc and see what device gets detected then? It could be in qualcomm usb mode
Click to expand...
Click to collapse
So I just took the device apart to try and get into qualcomm edl mode through hardware and now the front camera led turns red while charging. apart from that there are no signs of life though it won't show up in my pc's device manager even though I have the qualcomm drivers
ashawanz said:
So I just took the device apart to try and get into qualcomm edl mode through hardware and now the front camera led turns red while charging. apart from that there are no signs of life though it won't show up in my pc's device manager even though I have the qualcomm drivers
Click to expand...
Click to collapse
So you should let it charge till later in 6h
NOSS8 said:
Where did you find vendor update for 12.2.1.0 ?
Firmeware not vendor,not the same.
is the phone appear on pc?
If the the phone appear in qualcom usb, flashing in EDL will be possible and requires an authorization that only official repairers have.
Click to expand...
Click to collapse
Phone does not appear on pc and I got it from the evoX 5.1 thread. Ive flashed it before however and it didn't do this it worked just fine
ashawanz said:
Phone does not appear on pc and I got it from the evoX 5.1 thread. Ive flashed it before however and it didn't do this it worked just fine
Click to expand...
Click to collapse
This is the correct firmware.
What do you want to do in EDL mode?
NOSS8 said:
This is the correct firmware.
What do you want to do in EDL mode?
Click to expand...
Click to collapse
It's not booting, he doesn't want to get into edl. It's showing no reaction. But he could try pressing power button for 1min and look for vibration
To try to restore the phone yourself, you must use commands in fastboot or adb.
Tecardo said:
It's not booting, he doesn't want to get into edl. It's showing no reaction. But he could try pressing power button for 1min and look for vibration
Click to expand...
Click to collapse
the power button for a minute didnt do anything either sadly. Im trying to get into edl so i can try and recover it with QPST, but even after opening the phone up and trying to get into edl through hardware, i was only able to get the red charging light to start showing whilst charging. Should I try to disconnect and reconnect the battery maybe?
ashawanz said:
the power button for a minute didnt do anything either sadly. Im trying to get into edl so i can try and recover it with QPST, but even after opening the phone up and trying to get into edl through hardware, i was only able to get the red charging light to start showing whilst charging. Should I try to disconnect and reconnect the battery maybe?
Click to expand...
Click to collapse
Yep, can't hurt at this point.
You can try this:
Recharge the battery for at least 1 hour (even if you think it is already charged)
after connect it by usb and press the power button first,power button with volume -, button with volume +, and try to see if it appears on the pc and in what way.