Flashtool Set up Guide
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Before set up
Make sure disable Antivirus app otherwise you unable to install Flashtool .
Required
* I recommend Flashtool v 0.9.18.6 latest version might cause some problems.
* Java runtime for Flashtool - Here
* Xperia companion for Drivers - here
* Internet Required for first time.
Let's Start
* Install all 3 apps
Install Flashtool in C:/ Drive
*After installation of Flashtool, Open C:/ drive's Flashtool>drivers folder
* Now install and run Flashtool Drivers.exe check Fast boot and and Flash mode n install.
*Now Open xperia-companion (previously Sony pc companion) and connect your phone to pc/laptop after successful connection Xperia-companion will show your phone model no this means drivers installed successfully.
* Now Run Flashtool wait few seconds And connect your device .
*To check everything goes right , open your phone settings -devloper option-mark USB debugging go back to settings-security-mark unknown sources . × Switch Off×
*Run Flashtool
Flash mode
Connect your device into pc while holding volume down- Flashtool will show device connected in Flash mode.
Fastboot mode
Connect your device into pc while holding volume up+ (device notification light will glow) Flashtool will show Device connected in Fastboot mode.
(If Flashtool log show this message means you are good to go take further steps)
Flashtool set up complete.
I tried this method in both Windows 7 and 8.No need to disable driver signature enforcement in Windows 8.I m not sure about Windows 10.
Related
Im trying to follow this method for rooting http://forum.xda-developers.com/showthread.php?t=1340526 I have download those drivers and installed it.
When i try to get into recovery mode, my computer gives me a error Windows does not recognize the device.
This error
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Just download Kies. It has every driver you need.
crimpshrine83 said:
Just download Kies. It has every driver you need.
Click to expand...
Click to collapse
I Have Kies installed, same error
Uninstall Kies.
Reboot computer.
Then follow the steps in this thread:
http://forum.xda-developers.com/showthread.php?t=1340710
When i plug the device with those drivers installed i get this error message.
Im using Windows 7 Pro X64 if that matters
If you are trying to get into download mode, don't hold volume up and down, just hold volume down on this rogers phone. I had the exact same problem.
*Before We get things rolling, Make sure the Phone is recognized by your PC. DONE
*Rename the downloaded "su-3.0.5-efgh-signed.zip" to "Superuser.zip" (Don't type ".zip") and put it on your EXTERNAL SD card DONE
*Take the battery out and place it back DONE
*Hold Vol down, and plug the USB cable in. DONE
*On ODIN, Select the PDA button and browse to the recovery.tar DONE
*Select Start and see the magic do its thing. DONE
*It should flash the file to Recovery and reboot the phone. DONE
*Take the battery out again and now boot into recoveryDONE
*Power off phone, unplug USB, Hold Both Vol up + Vol down and Hit power
How do i perform this step?When i hold those 3 buttons the device just keeps vibrating nothing else
*PERFORM NANDROID BACKUP FOR YOUR OWN SAFETY* N/A
*Select Install zip from sdcard, choose the Superuser .zip and let it finish. N/A
*Reboot!N/A
hoping someone with i727r to chime in
Hi bro, i just wanna help those people who want to root their phone without downgrading. It tested, and work on my Miro on stock firmware 11.0.A.5.5 Okay, all you need is :
1. UnlockRoot (You can download it here)
2. Xperia Miro / Xperia Device (I think this guide will work for most 2011/2012 xperia devices)
3. PdaNet (Needed for Xperia driver. Download here)
ROOTING YOUR DEVICE MAY VOID YOUR WARRANTY!
The steps is :
1. go to your setting phone, and check the USB Debugging in Developers section
2. still at the setting, go to application section, and check the Unknown Source
3. Download the UnlockRoot software, and extract it.
4. Download the PdaNet, and install it. If PdaNet asked the device, select other. If you got this message, then click Install Anyway
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5. If needed, restart your PC/laptop. (If you are in win7/win8, when you are in boot, push the F8 button, and then select Disable Driver Signature. And then install the PdaNet)
6. After restarting your PC, then plug your phone on.
7. Run the UnlockRoot software, and click root!
8. Cheers! Your phone is rooted, check your phone if there is a SuperSU app. If there is SuperSU app, you're successfully rooting your phone
Sorry, if you still got a question, you can post it here or PM me Sorry for my bad english, this is my second thread
Does it need internet for anything?
No, you dont need any internet connection after downloading those files. If you dont need PdaNet (PdaNet used to connect to the internet using your phone as modem), then exit it. Its ok
my device does connect
I follow ur all steps but its show ur device does not connect
Hy everybody :laugh:
Whats Features in CWM 7.0.5.4 (M_A_H) version:
* cyan colors are stunning
* cwm can kill instantly without reboot
* cleanup tab option: shortcut to try to fix forcequits after updates, return to recovery and select on the main screen (Wipes Cache, dalvik, and fixes permissions)
* Standard options to backup and restore to either the SD card or internal storage
* Mount points match those of most running roms
* adb shell works as root (with or without system mounted)
* set boot mode menu to select the boot partition (hidden on know non-multiboot bootloaders)
* setbootmode and itsmagic command line tools for advanced users
* /data/linux directory is not deleted on erase userdata, nor backed up on nandroid backup (just like /data/media) to allow a space for linux files for dual boot and chroot linux installes.
Requirements:
1. Rooted Android Device.
2. Available SuperUser
How to install CWM on Xperia neo L:
1. Download Tool : Install CWM for Xperia neo L from below.
2. Enable USB Debugging On your Smart Phone.
3. ADB(Android Debugging Bridge) Drivers should be installed on your PC.
4. Extract files of the Tool to the PC and run the file named ("install-cwm1.cmd").
5. Connect the Xperia neo L (in switch-off mode) by pressing (Back key) to the PC.
6. Follow the instructions given when you open the file mentioned above.
7. When finished Reboot your phone.
8. DONE!
9. To get into CWM recovery menu,at boot time immediately repeatedly press the Volume Down to go to the CWM menu.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
:good::good::good::good::good::good::good::good::good::good::good::good:
thx
HOW TO UNBRICK Q NOAIR A30 (Qmobile).
DISCLIMER:
If you somehow manage to damage your phone all responsibility is on you not me. Here I want to declare that I did not developed these tools I just combined them and made a tutorial.
AIM:
To help people using low end devices. So let’s begin.
REQUIREMENTS:
A computer with windows operating system.
Q Noair A30 (Qmobile).
A USB data cable.
Q Noair A30 USB drivers.
SP Flash Tool.
Download Package from
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
HERE
1. Download and extract Q Noair A30 Unbrick Package at your desktop or any other comfortable place there you will find three folders.
2. Open Q Noair A30 USB drivers folder & run installDriver .exe.
3. Open SP Flash Tool folder & run flash tool .exe.
4. This screen will appear click on Scatter-loading.
5. Now this screen will appear, select MT6572_Android_scatter file from !Files_to_FlashTool folder.
6. Now this screen will appear check all the little box except PRELOADER and USRDATA and click on Download as shown in pic.
7. Now this screen will appear ignore the warning and click yes.
8. Now off your phone and remover its battery for few seconds and immediately connect it to PC via USB cable in power off condition and wait for flashing. After that this screen will appear with a green circle it means that you have successfully flashed your phone.
Congratulations!!!!!!!!!! you have done it:laugh:
NOTE:
As you have successfully recovered your phone and now if you want to install CWM on it then fallow my This tutorial.
bro can u tell us how to solve iemi error after flashing rom as i have lost my imei ... null
Your warranty is now void.
I am not responsible for bricked devices, dead SD cards. Please
before flashing it! YOU are choosing to make these modifications, and if
you point the finger at me for messing up your device, I will laugh at you .
Click to expand...
Click to collapse
REQUIREMENTS:
1. Rooted Micromax bolt a068
(It can be rooted by Framaroot by using the Barahir exploit)
2. Busybox installed
(Busybox installer is available on the Play Store)
3. Windows PC with MTK and ADB Drivers installed, you can do it from PDAnet (Links are in the downloads section)
4. MTK Droid Tool
DOWNLOADS:
MTKDroidTool - http://upfile.mobi/246121.205a7c738ab251cca07417fd509f2c47
Ini file - https://www.dropbox.com/s/jvtgj1qxah6oost/MTKdroidTOOLini.zip?dl=0
PDAnet - http://pdanet.co/a
PROCEDURE:
1. Install PDAnet to install drivers. Connect ur USB with usb debugging enabled (Enable USB debugging in your phone. Go to Settings—About phone—then tap 10 times on Build number. Then Find "Developer options'' in Settings. Tick mark USB debugging on. Keep Developer options on)
Turn off antivirus for sometime if there is any.
2. Extract MTKDroidTool.rar and ini file of just 1 kb and keep them in the same folder.
Now connect your device to the computer and open MTKDroidTool.exe
Connect your switched on rooted device to your computer and open MTKDroid tool.exe, the tool will recognize your device and connect to it, if the colour indicator in the bottom left comer is green,you already have root shell,and can go on to the next step, if it is yellow, click on the root button at the bottom, and wait for the progress bar, if the indicator stays yellow, or you get an error message, this probably means you do not have Busybox installed, you can install it from the google playstore. When the indicator turns to green you have root shell which is necessary for this operation.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Next click on the tab 'root, backup, recovery' and select 'to use boot from phone' then click on 'recovery and boot' and shortly after a dialogue box will appear asking if you want to make cwm recovery auto
matically' click Yes.
Then it will ask to install created recovery on phone, click Yes.
The device will reboot now into CWM, use volume keys for navigation and power key for ok.
Hit the Thanks button if u like Suraj Lulla's work.