Related
Hi my sony xperia E c1505 is not turning on it flashes red when hold power button it is not dead of battery fully charged left over night I unlocked the bootloader then i tried flashing it it says please turn on your phone and enable USB-debugging mode my phone can not turn on cause im in the bootloader after that I did somthing else but now i press power button just flashes red lights i am able to get in to flash mode and fastboot however i try flashing it but its says please enable USB-debugging is there a way to fix this and by the way im using flash tool and i have tried to update it with sony xperia update tool.
callum123457 said:
Hi my sony xperia E c1505 is not turning on it flashes red when hold power button it is not dead of battery fully charged left over night I unlocked the bootloader then i tried flashing it it says please turn on your phone and enable USB-debugging mode my phone can not turn on cause im in the bootloader after that I did somthing else but now i press power button just flashes red lights i am able to get in to flash mode and fastboot however i try flashing it but its says please enable USB-debugging is there a way to fix this and by the way im using flash tool and i have tried to update it with sony xperia update tool.
Click to expand...
Click to collapse
when you connect your phone in flashmode green light should stay on (press & hold vol down then plug usb in)
it should show
"device connected in flashmode"
IF you want fastboot mode
when you connect your phone in fastboot mode blue light should stay on (press & hold vol up then plug usb in)
NOTE-it should actually do bootloops....not sure why red light
callum123457 said:
Hi my sony xperia E c1505 is not turning on it flashes red when hold power button it is not dead of battery fully charged left over night I unlocked the bootloader then i tried flashing it it says please turn on your phone and enable USB-debugging mode my phone can not turn on cause im in the bootloader after that I did somthing else but now i press power button just flashes red lights i am able to get in to flash mode and fastboot however i try flashing it but its says please enable USB-debugging is there a way to fix this and by the way im using flash tool and i have tried to update it with sony xperia update tool.
Click to expand...
Click to collapse
Sometimes flash tool, while flashing tells me to turn on usb debugging (although its already on). So what do I do? Wait. After ten minutes(approx), device disconnects automatically and then flashtool requests me to connect in flash mode. So I disconect my usb cable and connect it again in flash mode and voila! flash begins. Worked for me, hope it works for u too..
Sent from my Xperia E dual using XDA Premium 4 mobile app
sohailferdous said:
Sometimes flash tool, while flashing tells me to turn on usb debugging (although its already on). So what do I do? Wait. After ten minutes(approx), device disconnects automatically and then flashtool requests me to connect in flash mode. So I disconect my usb cable and connect it again in flash mode and voila! flash begins. Worked for me, hope it works for u too..
Sent from my Xperia E dual using XDA Premium 4 mobile app
Click to expand...
Click to collapse
yes thats a common mistake
on flashmode connect phone in flashmode only when asked (or like you said ...you will have to do twice)
on fastboot mode your phone has to be connected in fastboot before selecting the fastboot mode
I'm having very similar trouble, i flashed FXP CM10 a little while ago until the phone stopped receiving a signal (which has happened a few times using CM10), unfortunately the battery died before i got home to flash it again. 3 days and 7 hours later and the battery still hasn't charged, i've managed to boot into android very quickly while it's connected to a wall charger but i get nothing at all if i try and connect in flashmode or fastboot.
Is the battery dead? Is there something i'm probably missing? I figured this might go to someway with hoping the OP.
[Edit: Good news! I've plugged into USB and i can get to the battery bar with the power symbol, maybe i can get to flashmode after all!]
[Edit 2:] Noticing the phone had just enough power to get to the battery/power symbol screen, held down the volume button for about a minute till it went through that cycle and managed to get it into flashmode, installed stock and plugged it into the wall. 5 mins later i hit the power button and it's working again! Hooray!
GeoH85 said:
I'm having very similar trouble, i flashed FXP CM10 a little while ago until the phone stopped receiving a signal (which has happened a few times using CM10), unfortunately the battery died before i got home to flash it again. 3 days and 7 hours later and the battery still hasn't charged, i've managed to boot into android very quickly while it's connected to a wall charger but i get nothing at all if i try and connect in flashmode or fastboot.
Is the battery dead? Is there something i'm probably missing? I figured this might go to someway with hoping the OP.
[Edit: Good news! I've plugged into USB and i can get to the battery bar with the power symbol, maybe i can get to flashmode after all!]
[Edit 2:] Noticing the phone had just enough power to get to the battery/power symbol screen, held down the volume button for about a minute till it went through that cycle and managed to get it into flashmode, installed stock and plugged it into the wall. 5 mins later i hit the power button and it's working again! Hooray!
Click to expand...
Click to collapse
use jim34 cm10 with hsr0 kernel....FXP IS CRAP for daily use
don't connect your phone to the pc until flashtool asks you to. I get that thing sometimes when I reflash a rom or kernel
Sent from my ST21i using Tapatalk
Hi. My device is hardbricked. I see no lights while charging. Flashtool doesn't see my device.how can i fix this?
Edit:Easily fixed it.I plugged my device into the computer.I entered platform-tools and flashed boot.img.I saw "waiting for device" And i pressed volume up and power buttons. Suddenly boot flashed and i recovered my phone
You are very unlikely to have hard bricked it unless you have unlocked the boot and flashed something wrong.
If you did this please help us help you by telling us what you did just before this happened.
Also, just leave the phone on charge (Wall charger) for 24 hours and then see what happens.
In the mean time read this
solution for no LEDs no response no fastboot devices.
Take two rubberbands one to hold down the power button and one to hold down the volume up button on Xperia Z3 dual. I spent a lot of time figuring this out. Alter a few minutes the phone just booted up from the dead. It worked for me 3 times. Now if someone can tell me how to fix the fastboot remote command not allowed error I'll be happy.
Fastboot remote command not allowed SOLVED
stevenmanzano said:
Take two rubberbands one to hold down the power button and one to hold down the volume up button on Xperia Z3 dual. I spent a lot of time figuring this out. Alter a few minutes the phone just booted up from the dead. It worked for me 3 times. Now if someone can tell me how to fix the fastboot remote command not allowed error I'll be happy.
Click to expand...
Click to collapse
Hello
I had the same problem with REMOTE COMMAND NOT ALLOWED till i managed to solve it.
1st thing you need to clean that ANDROID folder you made on C: drive.Install all from the begining including flashtool.Boot windows to install unsigned drivers.In the flash tool folder youll find the driver downloader,just enable usb debugging and choose Mass Storage not MTP .; You have 4 options usb debug on/off and usb connectivity MTP or Mas Storage ;with every version selected connect and disconnect from pc with flashtool running.
When you use Fastboot start the flashtool and close it if it cant kill ADB (that assuming you succeeded in installing drivers).
Good Luck
Please tell me D6603 testpoint
bgbgtbvan said:
Please tell me D6603 testpoint
Click to expand...
Click to collapse
you must read this
http://forum.xda-developers.com/showthread.php?t=2646405&page=54
john abruzzi said:
you must read this
http://forum.xda-developers.com/showthread.php?t=2646405&page=54
Click to expand...
Click to collapse
i have an xperia e3 d2212 stuck pon sony logo....bootloader is unlocked....i m able to enter fastboot so i flashed kernel.sin and system.sin after extracting from stock ftf but it didnt workwed...also,,i m not able to enter flash mode as the flash tool doesnt detects it in flashmode...but when i press power button and volume down the green led lights up...i have reinstalled flashtool many times and also reinstalled the drivers many times...any fix for this??
mihir762000 said:
i have an xperia e3 d2212 stuck pon sony logo....bootloader is unlocked....i m able to enter fastboot so i flashed kernel.sin and system.sin after extracting from stock ftf but it didnt workwed...also,,i m not able to enter flash mode as the flash tool doesnt detects it in flashmode...but when i press power button and volume down the green led lights up...i have reinstalled flashtool many times and also reinstalled the drivers many times...any fix for this??
Click to expand...
Click to collapse
Try a different driver package from another download source and use another usb on your pc.
Maybe it works. If your device can enter flash mode it definitely can be recovered.
Omario-242 said:
Try a different driver package from another download source and use another usb on your pc.
Maybe it works. If your device can enter flash mode it definitely can be recovered.
Click to expand...
Click to collapse
first of all my phone cant enter flashmode..(just the green light lits up)..secondly,,i have tried to reinstall drivers many times and i have tried to flash the system.sin and kernel.sin of 3 diffrent ftf rom for xperia e3 dual....is there any other solution..???
mihir762000 said:
first of all my phone cant enter flashmode..(just the green light lits up)..secondly,,i have tried to reinstall drivers many times and i have tried to flash the system.sin and kernel.sin of 3 diffrent ftf rom for xperia e3 dual....is there any other solution..???
Click to expand...
Click to collapse
The green led indicates flash mode so the problem is probably on your PC not detecting it properly. Does it show up in the system manager of windows if you plug it in at all? (Like a new device/android with a yellow triangle)
You could also try to fastboot a recovery and flashing a ROM from there. Not sure if it works but that's what I would try.
i m not even able to fastboot a recovery ...tried twrp and cwm both of them...
Me too
in my phone after charging 24h, only the red LED blinks, this is not normal any suggestions?
--------------edit
ok another week and still nothing
maybe I'll describe the problem:
I wanted to upload clean soft 5.1.1 and flash it
after the phone turned off it's start in recovery i used zip with SU and the phone turned off with no respond i try too reset (vol- + vol+ + power) but no reaction
there were no three vib
so I found that you have to reset the button under the sd flip
after this treatment you already know the charging of 3 days and only the red LED blinks
So any suggestions??
|
I‘m having the same problem, I can’t open my Xperia Z3. I tried with holding on/off button, holding volume up and on/off button, holding volume down and on/off button. When I connect it to PC, nothings happen. No vibrates, no led on, no screen on. What should I do?
ibo90p said:
I‘m having the same problem, I can’t open my Xperia Z3. I tried with holding on/off button, holding volume up and on/off button, holding volume down and on/off button. When I connect it to PC, nothings happen. No vibrates, no led on, no screen on. What should I do?
Click to expand...
Click to collapse
Like you I have a Xperia Z3 mines the 6633 variant.. Signs were showing it to be hard bricked, for example:
No led charge indication!
No power led!
No fastboot leds!
No USB detection sound when plugging into windows.
Literally a Z3 that was essentially a glass brick I bought off ebay for £6.50 GBP for spares/repair.
Since I had a bricked device, I had nothing to loose.
I applied heat to the rear glass with a hair drier & removed the panel, I removed the battery ribbon cable & plugged in via USB only to find the phone would show LEDs so put it on charge.
The Z3 now goes into flash mode, so then re-flashed a stock ROM from flashtool. I did a apps log & user data wipe, cust reset & fota reset.
To date I have no idea why the phone would not take a charge before or even detect via USB, though Id say give this method a go, you may be surprised!!
Good luck
Hallo people,
I have a very big problem with my d6633. I installed tonight TWRP - so fas, so good. After installing TWRP asked me to root the device, I said YES. My bootloader was unlocked. Then I couldn't exit TWRP. After every reboot the device started into TWRP. Now I can not start the device. I tried with Power+ Volume+, reset button - nothing.
Any suggestions?
Thanks for your help.
mazagi said:
Hallo people,
I have a very big problem with my d6633. I installed tonight TWRP - so fas, so good. After installing TWRP asked me to root the device, I said YES. My bootloader was unlocked. Then I couldn't exit TWRP. After every reboot the device started into TWRP. Now I can not start the device. I tried with Power+ Volume+, reset button - nothing.
Any suggestions?
Thanks for your help.
Click to expand...
Click to collapse
Use flashtool go back stock, after flash twrp, flash supersu manually, don't let twrp install for you
yuzhengwen said:
Use flashtool go back stock, after flash twrp, flash supersu manually, don't let twrp install for you
Click to expand...
Click to collapse
How can I do that? There is no power on my device. And I think I cannot charge it...
mazagi said:
How can I do that? There is no power on my device. And I think I cannot charge it...
Click to expand...
Click to collapse
Google using flashtool to flash stock firmware
yuzhengwen said:
Google using flashtool to flash stock firmware
Click to expand...
Click to collapse
No chance. The device will not be detected. I can not charge it.
mazagi said:
No chance. The device will not be detected. I can not charge it.
Click to expand...
Click to collapse
How much % did it have before you started the procedure?
Did you try holding down vol+ and then plugging it into USB?
Hello Jkay7,
Thanks for your support. My solution was to leave the device switched off over the night. Connected via original cable. Today in the morning my dyouzhengwen evice was detected via flash tool and as youzhengwen suggested I could flash the original ftf file.
artusk01 said:
Hello Jkay7,
Thanks for your support. My solution was to leave the device switched off over the night. Connected via original cable. Today in the morning my dyouzhengwen evice was detected via flash tool and as youzhengwen suggested I could flash the original ftf file.
Click to expand...
Click to collapse
Nice to hear that!
Any help would be appreciated
Sony Xperia Z3 Dual D6633
I have tried just about every method seen. My problem with the flashtool or PC companion is that the phone is recognized by the computer but I can only start to turn the device on which I don't believe it actually boots. Broken display and new display does not power on.
Or it connects in fastboot by holding volume up when connecting. This shows a blue led.
But trying to connect in flash mode by holding power down just makes the led flash red then green continuously.
And for the pc companion it always says the connection was unsuccessful once the led turns green on the device.
I got the phone for only $40 in this condition. So I cannot say what entirely was wrong or what it's last working state was.
I bought a new screen and power flex cable. As well as a back plate and tempered glass protectors. I was going to wait until everything works perfect speakers and all before I sealed it tight with water proof adhesive stickers.
Even before I bought the new power flex the computer recognized it and the battery health and charge %. The battery was able to charge. But I couldn't turn the device on.
The computer confirmed that it had been at 29% after some time charging and then 100% after leaving it on charge.
Now with the new screen and power cable the phone still does nothing if not plugged it. The light was red at first, but then yellow, then after some time green when the battery fully charged. This was again even before the new parts.
I have to plug it in to try anything.
It goes red then starts to turn on and turns green.
But I hear no sound, get no vibrations, the computer only sees it as the phone and shows absolutely nothing on the removable disk. Just blank when I click on the drive volume. But it is seen as an Xperia D6633 phone or fastboot Android device.
I've tried the reset button, holding power and volume up, volume down, all three. Tried my factory cable. Different cables, different ports, uninstalling it from service manager and letting the flash tool recognize and install it.
I also tried the new display on the old power flex and the old display on the new power flex.
Nothing changed, no vibrations, no sounds, system never actually fully starts as far as I can tell, and cannot connect in flash mode only fast boot. And the flashable file is only seen in flash mode. Fastboot can only see the folder but it is ready to flash files as far as I can tell.
@xdathekilljoy
That's a lot of money you're putting into an (apparently) broken phone Brave!
Okay so what happens if you hold Vol+ while it's shut down and then connect it to USB, the LED turns blue, right?
So why does flashing it from there on not work?
Jkay7 said:
@xdathekilljoy
That's a lot of money you're putting into an (apparently) broken phone Brave!
Okay so what happens if you hold Vol+ while it's shut down and then connect it to USB, the LED turns blue, right?
So why does flashing it from there on not work?
Click to expand...
Click to collapse
Well it didn't seem that broken at first and both it and the display were only about 37 piece. Power flex was almost 10. Seemed like a rightful price.
Yes the led turns blue and it is in fastboot mode. The flash file seems to only be readable for flashing in flash mode "volume down". I can see the folder of the flash file in fastboot mode " volume up ", but not in a flashable format.
And when connecting " volume down " it fails a connection while the led just flashes green to red to green to red continually
Two updates
1. I thought I should mention that when I do plug the phone in to a charger or computer the top does get a bit warm or hot as well as the led turns on. Different color depending.
2. With much fiddling and trying if holding the volume down button for different lengths of time while connecting up a computer I finally got it to connect in flash mode and flashed a file...... No change.
At this point maybe I should try a new battery for the hell of it even though this one seems to be working.
Or there is a minute hardware damage somewhere. Maybe the power ic? Or s capacitor?
I have T-Mobile Z3 (D6616) that I rooted and flashed TWRP on with no issues. Today I tried to flash ZyxxOS on it. after wiping and installing I went to reboot. The phone only powered off and then no matter what I do will not power on. I've tried all the button combos, LED's don't flash, I used the little yellow button by the sim, nothing.
If there is anything I can add let me know and I'll try to help to the best of my abilities.
thanks, Nathan
EDIT: If anyone can help me to the point that the phone boots or is completely fixed, I'll buy you a 6 pack of beer (or soda if you're too young to drink)
EDIT2: I let the phone charge all night and now (still plugged in) the notification LED is glowing red
Try to boot into Fastboot mode by holding the volume up then plug in the usb into your phone, if it detects then use the sony tool to reflash your firmware and it should work. If fastboot doesnt detect then I don't know what else to say.
serophia said:
Try to boot into Fastboot mode by holding the volume up then plug in the usb into your phone, if it detects then use the sony tool to reflash your firmware and it should work. If fastboot doesnt detect then I don't know what else to say.
Click to expand...
Click to collapse
Yeah it doesn't respond to anything. I've tried loading into fastboot, even holding all the button combos for a whole minute.
nathanmcneil said:
Yeah it doesn't respond to anything. I've tried loading into fastboot, even holding all the button combos for a whole minute.
Click to expand...
Click to collapse
Read these two threads and try it out. It may or may not work but its worth a shot.
http://forum.xda-developers.com/showthread.php?t=1849170
http://forum.xda-developers.com/showpost.php?p=37844592&postcount=317
nathanmcneil said:
I have T-Mobile Z3 (D6616) that I rooted and flashed TWRP on with no issues. Today I tried to flash ZyxxOS on it. after wiping and installing I went to reboot. The phone only powered off and then no matter what I do will not power on. I've tried all the button combos, LED's don't flash, I used the little yellow button by the sim, nothing.
If there is anything I can add let me know and I'll try to help to the best of my abilities.
thanks, Nathan
EDIT: If anyone can help me to the point that the phone boots or is completely fixed, I'll buy you a 6 pack of beer (or soda if you're too young to drink)
EDIT2: I let the phone charge all night and now (still plugged in) the notification LED is glowing red
Click to expand...
Click to collapse
How long did you hold the reset button for? I had the same issue with a z2 tablet and I had to hold the button for at least 2 minutes.
Yes nathan,try to do this what @BladeRunner says:hold buttons for mor time.
Do you tried flash phone with flashtool?
Послато са SM-G901F уз помоћ Тапатока
Allek84 said:
Yes nathan,try to do this what @BladeRunner says:hold buttons for mor time.
Do you tried flash phone with flashtool?
Послато са SM-G901F уз помоћ Тапатока
Click to expand...
Click to collapse
So I left the phone on the (wall) charger all night and when I woke up the notification light was red. I hit volume down +power and the phone vibrated 3 times but nothing else happened. After that I tried connecting it to flash tool with a rubberband on the volume up botton. Flashtool's notification screen thing kept repeating "phone connected adb disabled" and then "device disconnected". I let it do that for about an hour before I took it off and put it back on the charger.
Should I still try and reset it by holding it for a few minutes? I read the softbrick thread linked above but i'm not sure what I should do or where my situation fits into that thread.
thanks, Nathan
nathanmcneil said:
So I left the phone on the (wall) charger all night and when I woke up the notification light was red. I hit volume down +power and the phone vibrated 3 times but nothing else happened. After that I tried connecting it to flash tool with a rubberband on the volume up botton. Flashtool's notification screen thing kept repeating "phone connected adb disabled" and then "device disconnected". I let it do that for about an hour before I took it off and put it back on the charger.
Should I still try and reset it by holding it for a few minutes? I read the softbrick thread linked above but i'm not sure what I should do or where my situation fits into that thread.
thanks, Nathan
Click to expand...
Click to collapse
wwouldn't you connect it to the flash tool with volume button down? That might at least get it into flashmode.
BladeRunner said:
wwouldn't you connect it to the flash tool with volume button down? That might at least get it into flashmode.
Click to expand...
Click to collapse
I tried that, leaving it with flashtool waiting to connect and my phone connected with a rubberband on the volume down overnight last night. Nothing happened and now flashtool didn't even recognize the phone.
nathanmcneil said:
I tried that, leaving it with flashtool waiting to connect and my phone connected with a rubberband on the volume down overnight last night. Nothing happened and now flashtool didn't even recognize the phone.
Click to expand...
Click to collapse
Try this, open up flashtool and select your firmware, then click on the flash icon, after you clicked flash hold the volume down while connecting the usb cable and see if it the led changes from red to green/blue. Also what version of flashtool are you using? Maybe thats why its not detecting via the rubberband method. Also give this a go as well:
Recovery Mode:
Turn off the device
Press and hold Volume UP + Volume Down Key
then Press and hold Power key while pressing these keys
then press Camera key to enter Android System Recovery
Release all key when you see Android icon
serophia said:
Try this, open up flashtool and select your firmware, then click on the flash icon, after you clicked flash hold the volume down while connecting the usb cable and see if it the led changes from red to green/blue. Also what version of flashtool are you using? Maybe thats why its not detecting via the rubberband method. Also give this a go as well:
Recovery Mode:
Turn off the device
Press and hold Volume UP + Volume Down Key
then Press and hold Power key while pressing these keys
then press Camera key to enter Android System Recovery
Release all key when you see Android icon
Click to expand...
Click to collapse
im using version 0.9.19.8 but I am updating to 0.9.19.10 right now to see if that changes anything. Also how do I know if it's off? the phone doesn't do anything when i hit the power button.
nathanmcneil said:
im using version 0.9.19.8 but I am updating to 0.9.19.10 right now to see if that changes anything. Also how do I know if it's off? the phone doesn't do anything when i hit the power button.
Click to expand...
Click to collapse
If you plug in your charging cable and a red led is on that means it is powered off. So just try the button combination I have mentioned and hope it boots into stock recovery to try a factory reset.
serophia said:
If you plug in your charging cable and a red led is on that means it is powered off. So just try the button combination I have mentioned and hope it boots into stock recovery to try a factory reset.
Click to expand...
Click to collapse
I did the rubber band trick with the new flashtool, and the flashtool log just says,
device connected with USB debugging disabled
for 2011 devices line, make sure you are not in MTP mode
device disconnected
I get this over and over and it has been like this pretty much all day.
*EDIT: i held down power and volume down for a really long time this time and the led blinks red 3 times while I hold the buttons down.*
nathanmcneil said:
I did the rubber band trick with the new flashtool, and the flashtool log just says,
device connected with USB debugging disabled
for 2011 devices line, make sure you are not in MTP mode
device disconnected
I get this over and over and it has been like this pretty much all day.
Click to expand...
Click to collapse
Darn, not much you can do since USB Debugging is disabled. Also is PC companion running the same time as Flashtool? That can conflict with it. If they are both running make sure to close PC companion and give it another go. Three red blinks means the battery is drained completely, but you said you charged it overnight. hmmmmm.....
EDIT: Leave it charging using original cable + wall charger for 10-30 minutes, after that unplug from wall charger with cable still intact then hold volume up and plug to PC and hope you see the Flashmode LED.
serophia said:
Darn, not much you can do since USB Debugging is disabled. Also is PC companion running the same time as Flashtool? That can conflict with it. If they are both running make sure to close PC companion and give it another go. Three red blinks means the battery is drained completely, but you said you charged it overnight. hmmmmm.....
EDIT: Leave it charging using original cable + wall charger for 10-30 minutes, after that unplug from wall charger with cable still intact then hold volume up and plug to PC and hope you see the Flashmode LED.
Click to expand...
Click to collapse
So I tried that and just got the same thing as before, with the "device connected with USB Debugging disabled." is there anything we can do to try and re-enable usb debugging in the phones current state?
nathanmcneil said:
So I tried that and just got the same thing as before, with the "device connected with USB Debugging disabled." is there anything we can do to try and re-enable usb debugging in the phones current state?
Click to expand...
Click to collapse
http://forum.xda-developers.com/z3/help/sony-xperia-z3-hard-bricked-t3026373
Try these methods, if still no luck your last option is to send it in for repair
Hello everyone,
I was trying to flash a firmware into my Samsung Galaxy J4+ (SM-J415FN) using Odin3. While the Odin3 was flashing the firmware, electricity got cut off and the PC went off.
The phone showed a screen: "An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC Software".
When the electricity came back on, I connected my phone to the PC, and the phone started boot looping in the same screen. When I remove the plug, it stays off. Once I reconnect the plug, it starts boot looping. If I press POWER DOWN + UP at the same time while it is turning on (in order to go to DOWNLOAD MODE), it works, but once I press the VOLUME UP to CONTINUE, it shows the DOWNLOAD screen, stay there for a couple seconds, and then start looping again.
What can I do? Please, I really need to solve this.
kapmino269 said:
See this :
https://forum.xda-developers.com/ga...tloop-actually-bootloop-t3996925/post80803883
Click to expand...
Click to collapse
Not necessary.
The battery has become depleted.
Boot to the download mode confirmation screen with the USB cable attached to PC. Do NOT select up to go to DOWNLOAD mode.
Leave in this state for a good few hours, may even need overnight.
This is to get some charge into the device, albeit slowly.
After a few hours try and swap to the mains charger. Hopefully the device will not turn off. If it stays on leave the mains charger connected for a while then press up to go to DOWNLOAD mode.
kapmino269 said:
No tried later .
It won't be charged except if u charge battery manually .
Click to expand...
Click to collapse
Trust me It will. If it works on the J6 it should work on the J4.
kapmino269 said:
My phone battery became empty when flashing odin .
I was trying to charge phone in download mode for 3 days and I failed when flashing phone power off .
No way with me to do except 1 way as KG was prenormal to charge battery .
He can do 1 thing .
Flash recovery and there, phone can be charged .?
OR
Charge battery
Click to expand...
Click to collapse
Not download mode. The download mode confirmation screen.
It's worked for several others with the same problem, plus I've tested it myself.
ashyx said:
Not necessary.
The battery has become depleted.
Boot to the download mode confirmation screen with the USB cable attached to PC. Do NOT select up to go to DOWNLOAD mode.
Leave in this state for a good few hours, may even need overnight.
This is to get some charge into the device, albeit slowly.
After a few hours try and swap to the mains charger. Hopefully the device will not turn off. If it stays on leave the mains charger connected for a while then press up to go to DOWNLOAD mode.
Click to expand...
Click to collapse
hi, i have the same problem on the same device, i am trying this but after some minutes on the confirmation screen it reboots... what can i do?
i have the same problem the Phone is rebooting in the confirmation screen.
xX_Justin said:
i have the same problem the Phone is rebooting in the confirmation screen.
Click to expand...
Click to collapse
Hi, i've fixed this charging the phone not in confirmation screen but in the screen with serial number and imei (volume up+volume down+power button, and plug the usb cable, then release the button slowly)
If the phone reboots release the volume up first, then the volume down and then the power button.
Now you leave it charging and then reboot in download mode and flash rom with odin.
Let me know if you fixed it!
gi0vann1_ said:
Hi, i've fixed this charging the phone not in confirmation screen but in the screen with serial number and imei (volume up+volume down+power button, and plug the usb cable, then release the button slowly)
If the phone reboots release the volume up first, then the volume down and then the power button.
Now you leave it charging and then reboot in download mode and flash rom with odin.
Let me know if you fixed it!
Click to expand...
Click to collapse
If i plug it in pc, got bootloop in confirmation screen, enter download mode, imei screen.
Last hope is plug it in charger, press Vol Up + Vol Down + Plug cable to charger (i leave it in confirmation screen don't press Vol Up or Down).
After an hours i take it out and plug it in pc, press Vol Up to enter Download mode and voila it didn't reboot so i just flash it with Odin.
I'm in bootloop as well, and for some reason, even when on 'enter download mode' confirmation page, the device turns off 30secs later. Same behaviour when I go on the page with IMEI, but there the device stays powered on longer (a minute or so). All while the device is plugged into my PC. Any help?