Ok, this is a real particular question and I doubt anyone can figure this out but I'll ask nonetheless.
Trying to sync my Moga Pro to my rooted Note 5 so that I can get it to work with the Gear VR. Using both the Pivot app and Universal Drivers app I was able to sync to Mode A. However, Mode B is not being recognized by either app.
Anyone have any suggestions?
Related
So I just bought a Moga Pro Power controller, and I tried to connect to it, using the official Moga Pivot app.
First I thougt that the app is buggy, cause it stopped while connecting. And when the controller was paired, I couldn't even open my Moga-using games. But considering that the app works perfectly on every other N5, except mine, I started to think that franco kernel's bluetooth settings are the reason for that.
So I flashed stock kernel, but the problem still occurs...
I can receive and send files, just that damn app stops working everytime (i also tried reinstalling it).
Please help, I dont want to send that controller back, cause its my phone's fault :/
Moga pro controller
44-RON said:
So I just bought a Moga Pro Power controller, and I tried to connect to it, using the official Moga Pivot app.
First I thougt that the app is buggy, cause it stopped while connecting. And when the controller was paired, I couldn't even open my Moga-using games. But considering that the app works perfectly on every other N5, except mine, I started to think that franco kernel's bluetooth settings are the reason for that.
So I flashed stock kernel, but the problem still occurs...
I can receive and send files, just that damn app stops working everytime (i also tried reinstalling it).
Please help, I dont want to send that controller back, cause its my phone's fault :/
Click to expand...
Click to collapse
Generally for all Android smart phone Moga controller connects in the same way
as with nexus 5.
Kindly go through this i hope it will help you out
https://www.youtube.com/watch?v=uu2XhU-r5BU
joannn said:
Generally for all Android smart phone Moga controller connects in the same way
as with nexus 5.
Kindly go through this i hope it will help you out
https://www.youtube.com/watch?v=uu2XhU-r5BU
Click to expand...
Click to collapse
Thanks, but that's exactly what I did
For about 15 times...
The problem occurs when the app uses bluetooth. It freezes/gives me error messages.
I guess I have to flash stock firmware to get rid of this problem, cause I already tried everything that came to my mind
Hello there,
I am trying to find use for my old devices, recently just had a bambino and im trying to keep him entertained whilst driving and its hard work. I was thinking of mounting my old SG Tab 2 tablet in the back of the car and control its functions via my old SG 2 phone in front, mainly video watching for him to be honest. My SG2 is rooted, I am currently using an S5 but I would like to stick with the older phone if possible.
I have been reading a little into using 'Tablet Remote' but as far as i gather the tablet needs to be connected to a tv.
Can anyone point me in the right direction please?
Hi,
I will have your thread moved to your device section. You will need to register on XDA to reply to anyone though.
Good luck!
XDA Visitor said:
Hello there,
I am trying to find use for my old devices, recently just had a bambino and im trying to keep him entertained whilst driving and its hard work. I was thinking of mounting my old SG Tab 2 tablet in the back of the car and control its functions via my old SG 2 phone in front, mainly video watching for him to be honest. My SG2 is rooted, I am currently using an S5 but I would like to stick with the older phone if possible.
I have been reading a little into using 'Tablet Remote' but as far as i gather the tablet needs to be connected to a tv.
Can anyone point me in the right direction please?
Click to expand...
Click to collapse
Tablet Remote doesn't need a tv connected, Just 2 Android devices, here's the steps to use as mentioned in Google Play
1) Installation
Install the Tablet Remote on both devices;
2) Setup
For the receiver device (the tablet), go to the "setup" section and make sure the two options are check by selecting them and by enable Tablet Remote as a keyboard;
3) Connection
Go to the "connection" section and select the device you want to connect.
You'll have a notification on both devices when they connect with each other. If you don't find the other device, you can use the "scan device" and "make device discoverable" commands to make it appear in the list.
Only devices on your local area network (LAN) will be showed with the "scan devices" command. Make sure both devices have Tablet Remote on when you use that command.
If you have problem connecting with the device, try it with the other one or unbind both device and try it again.
4) Control
For the remote device (the phone), go to the "remote" section and you can start controlling the other device! In portrait mode, you'll have the remote setting and in landscape mode, you'll have the gamepad setting.
Gd man thanks for the help, i will give it a go and see how it works out in the car. Kudos
So I recently just rooted my Galaxy S4 mini mainly for the reason to connect a dualshock 4 to it. I've searched and searched on many forums and videos looking for the best/correct way to do it, and I've tried them all and get the same result. I've used the PC Sixaxis tool and programmed the Bluetooth to my phone, used the Controller compatibility tool to see if it is compatible (it is, and it connected and showed the controller inputs on the screen). But when I went to the main Sixaxis app and did the same process, and it gets to "listening for device" and never connects. I'm seeing if anyone can tell what the problem might be and help me out with it. Any thoughts?
Well, I was trying to sync a ps4 controller to this phone. And controller sync fine, but no input is registered by the os or any game.
Funny I tried to sync to my samsung note 4 and worked perfect.
I guess is another LG bug. Any ideas or workarounds?
Hi, I am new here, came for help
I've got Galaxy Watch 4 and tried to connect it to my smartphone LG V30. It connected only once after first start and then after disconecting I can't pair it again through the Galaxy Wearable app. My phone sees the device and can connect with it via Bluetooth but it doesnt work in app. To connect it again I have to reset the watch and start all the things from the beginning. I tried uninstall Galaxy Wearable app, turn off/on watch and smartphone, I called Samsung but they told they dont support non Samsung phones.
Anybody had also problem with pairibg and could help?
Hi, do you also have the Galaxy Watch4 Plugin installed from the Play store?
Everything works for me on my OnePlus Pro 8.
Yes, the plugin is installed.
galaxys said:
Hi, do you also have the Galaxy Watch4 Plugin installed from the Play store?
Everything works for me on my OnePlus Pro 8.
Click to expand...
Click to collapse
Glad to hear it ( Read it lol ) ! I also have oneplus 8 pro . Still waiting on watch lol .