Database Info

Samsung captivate speaker problem - return for new one?

Okay, so my samsung captivate speaker is pretty much broken and doesn't work properly anymore. I've had it for about a few weeks and now the speaker just doesn't make any more sounds. Music will not come out etc....i can get sound to work for a little bit but its only temporary and goes back to not working, i just hit the speaker part and it randomly starts to work again but it doesn't stay like that so im wondering if i can return it.
I bought it off craigslist so i don't have the receipt or anything like that, i also don't have the box since its at a friends house. Im wondering if i can go to an AT&T store and exchange it for a new one no questions asked without the receipt or box and the fact that i didn't buy it from at&t personally but it is originally from an at&t store (obv). Or will i have to do the other dreaded task of sending it back to samsung and be phoneless.

I doubt AT&T would accept it without anything at all, is it really that hard to get your box at your friends house? But besides that unless you can prove you're within your 30 days they wont do anything unless you have insurance. In your case I'd contact Samsung directly and they can probably run the serial, obviously you're still within a year lol.

okay, damn thats a shame.....i have to go through samsung. Im pretty sure its past the 30 days already too.

I had speaker problems when I slipped my Captivate into a really clear case made by Incipio. I believe that was the culprit. I also had to hit the phone against my palm to get the speaker to work again. I remove the phone from the case and played an entire album via speaker. No problem there. I returned the case and bought a Body Glove skin. Better.

Yea......the speaker is somewhat working fine now after playing youtube and some songs again......will see how it holds up.
I might just not send it back and go through all the hassle, i think it got messed up when i dropped it, shame cuz it was the only time i dropped it, maybe something got a little loose.
I havn't had the speaker not work on me for a good 6 hours so far will keep monitoring it.

me too. i bought it on ebay. So i dont know if at&t will fix it or replace it.

My external speaker stopped working for the first time today also. I read over on an AT&T forum that if you press on the speaker it will get it working again. I just tried it and now my phone works again. I had to press a little below the speaker.
Just another notch in the belt for what a crap product Samsung made. I've never dropped my phone or anything. Others are having this problem so it's a build quality issue or something. The connection with the speaker must be weak.

so i guess there's no other way to fix the problem except getting a new or refurb one?

Sound not working over loud speaker
Unplugged my cappy this morning and headed to work. All has been very quite...too quite, then realize that my cappy isn't making any noise
*panic mode* no media sound, ringtones, etc...
Read on the at&t forum that you can press firmly on the speaker and it 'fixes' the problem. WHAT!!!....that's a crappy cappy fix, anyway, what can you do... Speaker is working again, for how long? I don't know.

Same here, dropped my phone a couple of times. External speaker starts acting weird, connection keeps coming and going. Tapping fixes the problem only temporarily, it goes back to being dead only after a couple of seconds / minutes. seriously crappy. Everything else works fine though, headphone conenction / telephone speaker seems alright.
dallasweb said:
Unplugged my cappy this morning and headed to work. All has been very quite...too quite, then realize that my cappy isn't making any noise
*panic mode* no media sound, ringtones, etc...
Read on the at&t forum that you can press firmly on the speaker and it 'fixes' the problem. WHAT!!!....that's a crappy cappy fix, anyway, what can you do... Speaker is working again, for how long? I don't know.
Click to expand...
Click to collapse
Yeap. Pressing down on the speaker did the trick. It sorta fixed the problem. Cheers man.

As mentioned, if you can press down or slap the back of the phone and sound begins to work again, you have a shorting speaker or perhaps a poorly contacting ribbon cable. You can open the phone up and re-seat this in hopes it will help. It uses a ribbon cable design with a lock snap to press it against the contacts. I'd advise gently lifting the contacts with a small needle or tweezers then re-seating and retesting.
If you do that let me know and please report your results. You can also replace the speaker as well. I have an extra I don't currently need.

I purchased my Captivate on eBay just after Christmas, turned out the camera had a problem in the lens so I told them it was randomly rebooting. They allowed me to go exchange the phone since it was under warranty (had insurance but didnt use it) and since then, I have replaced it 2 more times.
See if you can talk to them on the phone and find out if your still covered, luckily I have a warranty exchange store near by, so it was real easy for me to exchange.
edit: forgot to mention I never had a receipt, I told them I got it from a third party seller. Since its an ATT phone, they should still accept the warranty

Press on the speaker if you have no sound!
Don't mean to dig up a dead horse but if you are having external sound issues I can verify pressing on the speaker does fix it.
This I discovered after 2 nandroid restores and a 4 reflashes with clean wipes. Plus removing several apps I had just installed.
Now I get to reinstall everything and update my ROM again.
It pays to search before panicking.

Intermittent speaker issues, specifically when I turn the speaker vol up to Max while playing music, burping the phone helps,
sent from my I896, rockin fasty kj3

Its funny you said this because I bought my girlfriend a captivate a couple months ago off eBay. The phone itself is fine last month the speaker also went out. It would only work if she tapped on the back of the phone. Well we called AT&T and told them, all they did was check the imei and see when it it was bought. It was only 11 months so its a good thing it failed now and not later. After a couple hours of troubleshooting with the good folks at AT&T and doing a master reset even though I told them that had nothing to do. They then transfered me over to the warranty department where a spent a couple more hours doing the same troubleshooting I did as with the AT&T reps. At last they said they would send me a new captivate. You should call the worst they can say is no.
Sent from my MB865 using XDA App

For those of you who do not have warranty or insurance, there is a fix for this.
I just got done with re assembling the phone after a fix I performed. It is real easy to do.
Things you need:
-A screwdriver (whatever the size is when you open the back cover, the four screws you see, that size)
-A small flat head screwdriver if you have one (not necessary but would help)
-Patience and some common sense.
Ok, to start off follow these steps http://forum.xda-developers.com/showthread.php?t=740022 to open the first 6 screws and then how to pop open the screen from the bezel(this is when a flat head screwdriver would be useful).
(go just to the step till the fifth picture in that thread, no need to go beyond that opening things!)
Now, you would see a screw on the left of the speaker. Now, other threads said that by loosening that screw the speaker would work. But, I did that and still had issues so I opened the phone like 4 times in total before I found out what it was. Now, notice that the speaker unit has a cable (orange colored) running into the main phone chip. It is connected there through which it functions. When you open that above mentioned thread to open the phone there is a picture showing to remove the that belt from the board. Follow that instructions, flip that tiny black clip up to remove the belt. In some cases there might be a blue sticker kind of thing on the belt, just take off that sticker. The problem seems that the belt is loosing contact which doesn't allow the speaker to get the sound input to put out sound through the speaker. So, take off the belt by flipping that switch and re insert it out there. Try to push it in properly or enough to align a white line on the belt and the chip. There is a white line to guide us there. That line should be totally straight when the belt is inserted appropriately. And now, flip that clip down and lock it. If you have loosened the screw left to the speaker, put it back in in normal force not excessive(no need to be more gentle here). You cannot leave it loose because it makes the whole unit move when it is loose eventually pulling off the belt from its place which causes the sound cut outs. The whole trick is to get the belt right in its place. So, make sure it is tight but not extra tight after you have managed to get the belt right. Put everything back together and now when you screw the last 6 screws again, the one in the top speaker corner affects the speaker unit, so don't push it too hard in. Just normal screwing. The rest should be done properly with normal force. This should solve it. I figured this out after opening the phone 4 times. And now playing songs since the past 6 hours non stop and its back in action again!
For all this, i did put in the battery and start the phone when I had opened it and tried messing around and figured out what was killing the sound, so this should be the ultimate solution to it. There is nothing else that can be affecting it now.
Most people must had faced this because they dropped their phones before which made the belt to move and hence the loose contacts inside. If not then, there are high chances that you bought it from someone or somewhere who had dropped it before!
Well that's it! Also, don't freak out in having to open the phone. You should just go to the step till the fifth picture. Which is very easily achievable!
Go, have fun with your WORKING speakers now!

More Useful speaker fixes
I am on my second captivate, I got a refurb since the speaker died on my first one.
My second speaker just started dying.
Before I had even read this thread all the way to the end I decided to tear apart my phone to get to the speaker to see if there was something loose that i could re-solder or reconnect.
Have you ever dropped a magnet in the dirt and picked it up and it was cover in little bits of iron?
I discovered that when I peeled the little metal cover off the speaker that it was covered in little tiny bits of metal that were stuck to the magnetic face of the speaker. I don't know how much this affects the speaker function but I cleaned it off and plugged the speaker back in and put it together and it works great.
I took a small flat head screwdriver that was magnetized and carefully scraped off the little bits of metal wiped it all clean. you wouldn't believe how much crap gets through that little tiny screen. I was able to peel of the little metal cover with my fingernail. It was very easy to take off, you could even remove the speaker cover without disassembling the the back cover.
I am not certain if my cleaning fix will solve the problem since I had removed the cable and shoved it all the way back in, but it might help make the speaker louder.
Anyways there's my first post. Hope it helps you all.

Number1Gsxxr said:
if you press on the speaker it will get it working again. I just tried it and now my phone works again. I had to press a little below the speaker.
Click to expand...
Click to collapse
Unbelievable but... It worked for me too! Thanks!

My external speaker stopped working for the first time today also. I read over on an AT&T forum that if you press on the speaker it will get it working again. I just tried it and now my phone works again. I had to press a little below the speaker.
Yes this solve the problem for the speaker no phone punch

I put a small piece of thick tape under the battery cover near the speaker and this keeps pressure on the speaker.

USB port issues

I am having issues with my Captivate's micro-USB port being loose. This is my second Captivate, and although it's still under warranty, the first one was RMA'd with the same issue. I never drop the phone while charging, etc, and I've tried multiple chargers so I really can't see why this would be happening. Both phones were 1008 versions, not sure if the 1008 is known to have this issue, or if I just have horrid luck. If anyone here can solder / fix the phone, I'm hesitant to go to AT&T again, as last time they made me go to the store and have the person working there verify that the USB port was not broken (luckily it still charged if you held it a certain way, and even more luckily I was able to flash stock before returning it!). Anyways, this phone is a refurb, and I did call and almost get it replaced as soon as I got it, as it had this issue slightly upon arrival, but decided it would be a hassle. It's only been about a month since the RMA, so I'm pretty sure that if I try now, they're going to get very mean about it, and possibly try and send me a bill for the phone, not to mention, the guy at the AT&T store will probably think something is up.
Any ideas are welcome, I love my Captivate, and I was just getting into develping on XDA :S
Sent from my Cappy using XDA Premium App
I actually found a fix to my issue. I actually was looking at it one day, and figured that in theory, it should be easy to fix, so I (CAREFULLY!!!) took a small knife I had and gently bent the inner part of the port up just a tad (it looked like it was too far down, and yes, I know it's supposed to be far down, but not that far), and it actually worked perfectly.

Thats weird... It kinda has to be what you're doing with it, since mine doesn't even have an irregular slight wiggle.
Obviously it could be just your luck but i doubt it.
edit: and who cares if the att dude thinks somethings up... its your $500..

Like I said, the second one actually had the issue upon arrival, but it was barely noticeable (the USB port would work, but if you moved the phone a lot, etc, it'd disconnect, then reconnect). I called in and talked to them, but decided not to RMA because it'd be a pain (in hindsight I should have...), and the problem just got worse.

Is the port internally lose? Or just when you plug a cable in it wiggles alot? Ive heard about people stretching the casing inside the port from alot of flashing (plugging in the usb). But if the hole port moves inside the phone thats no good lol. You should try to locate a nearby device service center and show them the problem and make sure you walk out with refurb thats fine. Dont worry about the people at atnt questioning it. Hell I use to walk in and just say "gps dosent work" and they would switch it out no questions.

What you said makes sense, the port looks like it's pretty sturdy, it's just that the cable wiggles a LOT, and it makes it hard to get it to even register.

I had the same issue but a new cable solved it
Sent from my samsung captivation

erraz said:
I had the same issue but a new cable solved it
Sent from my samsung captivation
Click to expand...
Click to collapse
I also had this issue, i opened up the stock Samsung Cable end to find that two of the four wires had insufficient strain relief and broke off at the solder joints

Oddly enough I had issues with the first cable as well, but I replaced it, and have tried others from my current.

SD Card Slot

Anyone else having issues with the mSd card slot?
Plug a card into mine and it makes a sound and works, knock the device or touch the card and it makes the unplugged sound and disappears..
Looking into the port the pins look like they are at a bit of an angle and the plastic slot moved a bit, a few of the screws weren't exactly tight so I gave them a quick tweak, the slot itself doesnt move anymore but the problem persists..
I've raised it with MS support and they are doing an advanced replacement but didnt know if anyone else had seen, had or heard of this before, I'd put it down to a build quality issue tbh..
Just hope they dont say its not covered as some of the screws have a bit of silver showing where I tweaked them, didnt take it to bits or anything depends how anal they are I guess...

Nope no issues.
I have seen a few people show images of obvious user damage they claim as magically appearing that Microsoft did returns on. You should be fine.

Had that same issue on mine; if I held the card in with my fingernail it would work fine, but as soon as I let go it would come out just enough that it would disconnect. Microsoft exchanged it no problem. My only issue was the support rep told me to send back all accessories, yet they only shipped me a lone Surface, with no charger! When I asked another support rep about it, they said that the accessories ship separately, which means I received my Surface overnight, but had to wait a week for the charger.

Yes, I had this issue on my previous surface. I got an exchange on it, as it randomly stopped booting a few weeks ago, and I haven't noticed it on my current one.

As long as I'm not the only one then, I did try a few different cards so knew it wasnt that, its not like I use the card much atm but its nice to have the extra space seeing as I dont have a bloody drop box app yet
Guy I live chated too at Surface support said just send the Surface back without any of the accessories, then rang me a few hours later as there was a problem on the system and then went through it on the phone, if only Samsung support were as good with this Slate 7 I have :/
Anyways replacement should be in the building shortly, it left the local UPS depot just before 6am, not sure how much use I'll get out of it tho as the charger is sat at home and I didnt even think about it until I saw the post above...

New device 50% power, that'll do, installing updates now, d'oh, battery will probably be dead by the time its done, it sbeen going for an hour and is installing 4 of 18...

Replacement sd card is a much better fit, doesn't wiggle in the slot at all and doesn't disconnect when you touch it..
However I might have a different problem now... :\

bump... anyway to fix this without an exchange? going back to school tomorrow and the closest MSoft store is 2 hours away (Tucson --> Scottsdale). The MSD is def loose and it constantly is disconnecting. pain in the ass when trying to listen to music.
my current solution is I stuck a tiny folded sheet of paper in between the msd and the tablet to try and hold it in place. so far so good, but its only been a few min...

eeisner said:
bump... anyway to fix this without an exchange? going back to school tomorrow and the closest MSoft store is 2 hours away (Tucson --> Scottsdale). The MSD is def loose and it constantly is disconnecting. pain in the ass when trying to listen to music.
my current solution is I stuck a tiny folded sheet of paper in between the msd and the tablet to try and hold it in place. so far so good, but its only been a few min...
Click to expand...
Click to collapse
I did mine on an advanced exchange so wasn't an issue for me, meant putting a holding charge on my card tho, not sure if that's an option..

Screen Flickering

I've read a few threads on the screen Flickering and there doesn't seem to be any resolution .
I'm on my 3rd tablet now (thanks best buy accident damage warranty!) And this one is flickering worse lately than ever. I updated to the latest firmware, yesterday only to boot up to horrible bouts of flickering during the setup screens.
The odd thing is, there seem to be no consistency to it. Some days it's so had I can't even use the thing, other days it doesn't happen at all. I use the tablet every day for notes or PDF viewing. I've used it with no magnetic cover (totally naked) and with the cover.. doesn't seem to change the occurrences.
I've turned overlays on/off force gpu render on/off.. nothing seems to fix it. Sometimes changing the overlay will reduce the flickering other times it doesn't affect it at all.
I hate to say it, but if I can't resolve it, I'm going to be forced to move to the surface 3.
I'm an electrical engineer and I've done as much trouble shooting as I can think to do.. but I've come up empty handed.
Anyone else have these problems? Has anyone found a definitive fix?

I sent mine back 3 times. The first was a reset. Thanks for wasting my time. The second was a motherboard and that didn’t do it. The third time they did a motherboard, digitizer, and usb port. It's finally stable and back to normal. After 5 trips back, the BB warranty triggers a new unit. Check if it triggers a refund.

I get it occasionally, so far I'm able to resolve it by booting into custom recovery (TWRP) and clearing dalvic to allow all apps to rebuild. Sometimes this resolves it for a few days, sometimes a couple of weeks. Its a repeatable "fix" that makes me question if the issue is related to memory or trim or something like that. Kind of reminds me of how with the first generation nexus 7s one would see slow downs after a while and filing storage with fake data then deleting it would improve performance for a while.

I'm definitely not a tender user of the device. I go back and forth between multiple ROM's and kernels on a daily basis testing what is testable, and unfortunately also what is not. Anyway, even though mine was bought as refurbished on eBay, I have never had any issues like the ones you describe. More specifically, I have never had any issues what-so-ever, that was not created due to my own ignorance. To me the device seems indestructible.
Besides, I would hate to be in the place of my device, or I would definitely have turned schizophrenic. Should I feel bad about pushing it through all this?

Because we're trying to figure out if it's related to a specific device type, which one do you have? P900, 905, 907A or another?

ShadowLea said:
Because we're trying to figure out if it's related to a specific device type, which one do you have? P900, 905, 907A or another?
Click to expand...
Click to collapse
P900 wifi. Us version bought at best buy.
Today the tablet has been rock solid, I have literally done nothing between when it was flickering like mad and now.
I wonder if it might be related to some kid of data transfer. either over wifi, or when data is written or read from storage or SD card. I've take then SD card out to eliminate that as the problem.

Mine was P900 from BB

Issue lies with the screen.
This happened with me I sent it back to Samsung, 3 times. They seem to have finally got it right. They replaced the battery and then the display screen. Now it appears to be working I will let you know after a month if it is still good. They also told me that they will not replace the device even though I bought it and the issue was right from the start. Not even 6 months old. When working the device is excellent.

Ah, so now we know for sure the battery is replaceable. That's good news. Maybe someday our batteries will no longer hold a charge and we can replace it. Now for a good video on tear down and what tools to use to do that and where to get a replacement battery. I know it's early for most of us but someday......we will have to replace that battery. I'm one of those that keep my toys (computers/laptops/tablets/phones,) for many years.

Mine is running like new since last service. Getting the BB Geek Squad warranty has paid for itself already. I get 2 years on anything over $500.

Mine is a p900. I purchased from samsung website. Mine has been doing it fresh out of box. So bummed.

Ive had my 12.2 since march and it recently started flickering. It seems to tuen of the screen for a millisecond especially when lots of refreshes happen. Like scrolling a pdf. A few days back it was bad. Now it has gotten better and I havent noticed anything.

{Diemex} said:
Ive had my 12.2 since march and it recently started flickering. It seems to tuen of the screen for a millisecond especially when lots of refreshes happen. Like scrolling a pdf. A few days back it was bad. Now it has gotten better and I havent noticed anything.
Click to expand...
Click to collapse
My P900 has just begun flickering exactly as you describe. So I should just be patient and hope it goes away by itself?

I'm flickering again. Turning the screen brighter is what triggers it for me. Returning to stock just to get it back and have it flicker again to hit the magic 5 returns may be what I have to do.

https://youtu.be/CvxbVft69Kg
I just followed this guide. Its been a week now, not had any flickering since I did it.

Manya3084 said:
I just followed this guide. Its been a week now, not had any flickering since I did it.
Click to expand...
Click to collapse
Lifting the motherboard only temporary close the gaps of cracked battery connector. The permanent fix need to do: re solder the battery connector.
Look closely under magnified glass or microscope , you'll see the cracked solders. You can test by pushing the connector slightly, a bad one will move easily or lift off from its solder joints.
This video was removed from the poster after I pointed out his guessing solution. Flickering screen has nothing to do with LCD connector on the motherboard.
Lifting mother board actually you're applying pressure on the battery connector from rear cover.

I have had my P900 sent to Samsung service twice without having the screen flicker fixed. I thought this was a known problem and that Samsung themselves should be aware of it? Maybe I should supply some XDA links next time...
Skickat från min SM-P900 via Tapatalk

bluebirch said:
I have had my P900 sent to Samsung service twice without having the screen flicker fixed. I thought this was a known problem and that Samsung themselves should be aware of it? Maybe I should supply some XDA links next time...
Skickat från min SM-P900 via Tapatalk
Click to expand...
Click to collapse
Depend on where you send for service, they know how to fix it now. Service Centers actually are contractors provide services for Samsung and others, the fact that most people don't know.
http://forum.xda-developers.com/showpost.php?p=59573206&postcount=100
It Works. Battery connector replaced. Smoooooth
After 2 visits to Samsung , my unit finally works fine.
Motherboard and LCD were changed first time. But issue persisted.
Second time, battery connector was replaced. Since then it has worked very very smoothly.

Beut said:
Depend on where you send for service, they know how to fix it now. Service Centers actually are contractors provide services for Samsung and others, the fact that most people don't know.
http://forum.xda-developers.com/showpost.php?p=59573206&postcount=100
It Works. Battery connector replaced. Smoooooth
After 2 visits to Samsung , my unit finally works fine.
Motherboard and LCD were changed first time. But issue persisted.
Second time, battery connector was replaced. Since then it has worked very very smoothly.
Click to expand...
Click to collapse
Thanks, missed that other thread. Next time, I'll send them an en explicit request to replace the battery comnector, and refer to those two threads.
Stefan
Tapatalked on some kind of Samsung tablet

Question Sim recognition issue

Owned the phone for about a month now. Phone was working perfectly fine for the majority of this time. I use 2 different sims and they were both working smoothly until recently.
A few days ago, I woke up and the phone wouldn't recognize the Sim cards anymore. I took out the Sim tray, cleaned the Sim cards and the tray as thoroughly as I could and they both started working again. A few days later, I restarted my phone and both of the Sims stopped working again.
This time nothing I would do would solve the matter, so for the next few days the phone wouldn't recognize either Sim. I have unlocked the bootloader and rooted, factory reset it and updated it none of which seems to solve the issue.
I use this phone for gaming so last night to my surprise one of the Sims started working (sim was in for a couple of days) and all connectivity was perfectly fine - I tried putting in my other Sim as well but again the phone wouldn't recognize them anymore. Tried putting in only one card on the Sim 1 slot but it made no difference. I don't understand what the issue could be.

Do you have a converted CN version or did you buy a global version? (just curious, as far as I know only CN -> WW versions faced this issue and I would like to know if this is a coincidence or an issue with these versions. But I could be wrong as well)
Nevertheless I would make use of warranty and send it back to Asus to get it repaired.

Yeah it's CN version > WW ROM. It's absurd how randomly it was hit with this issue. Again, the phone was reading a sim card perfectly fine out of the blue last night, then when I took out the Sim tray to insert another card, went back to square one and wouldn't recognize either.

I know.. If you had searched this forum or the rog reddit you would have noticed there are multiple topics like yours and all people explained the very same. Seems totally random.. sometimes it works, sometimes not. Unfortunately no one was ever able to post an accurate answer of why this is the case or how to fix it. At least there is none here, on reddit or the zentalk forums.
Since all device so far were CN -> WW version I don't know any successful case. Asus mostly rejects the support and redirects people to their sellers but those mostly refuse to do something. (they probably know that issue and it's cheaper to do nothing)
I wish you best of luck. Maybe you could try to contact Asus and report the outcome so we finally have a documented successful repair.
Edit: as said, that's only my knowledge, maybe there is a fix and someone found a way but they either didn't publish it or they posted it in a not so well known forum.

I wonder if the connections that touch the SIM are poorly designed. If it is such a widespread issue that randomly seems to come and go, it could be similar to the issue I had with the Kunai 3.
The pins on the side are designed to give a little when sliding the controller off and on the mount or charger. After moving them between the mount and charger twice, some pins fell off and others never popped back into place so they could make a connection. It turns out they never secured the pins well enough to handle it.

Hello, I had a similar issue.
My sim-cards wouldnt be recognized, sometimes only one of them, sometimes both. Additionally, my fingerprint-sensor wasnt working too. By checking pictures of a disassembled phone I could locate the problem inside. It has a connector on the lower end of the phone, which is for sim and FP-sensor. I can definitely and easily come loose.
Quick and dirty fix for me, was pressing with controlled but quite some force on the lower end of the LED-Rog logo while the phone laying flat on the table. I used my thumb, pushed and restarted the phone to check. Didnt work, pushed a bit harder and restarted again until it worked. The back glass has some flex to it, to make it possible to push the connector back in. Still, be careful to not break it, if you try it yourself.
When I found that solution, I've sent it in on warranty for proper fixing with this Information to ASUS. They replaced allegedly the mainboard. But I actually think, they just fixed the connector in place, because bending the phone to a certain degree "unfixed" it in my case again. I dont know, if its the same issue you have, but if it is, hope it helps everyone.

r0me5 said:
Hello, I had a similar issue.
My sim-cards wouldnt be recognized, sometimes only one of them, sometimes both. Additionally, my fingerprint-sensor wasnt working too. By checking pictures of a disassembled phone I could locate the problem inside. It has a connector on the lower end of the phone, which is for sim and FP-sensor. I can definitely and easily come loose.
Quick and dirty fix for me, was pressing with controlled but quite some force on the lower end of the LED-Rog logo while the phone laying flat on the table. I used my thumb, pushed and restarted the phone to check. Didnt work, pushed a bit harder and restarted again until it worked. The back glass has some flex to it, to make it possible to push the connector back in. Still, be careful to not break it, if you try it yourself.
When I found that solution, I've sent it in on warranty for proper fixing with this Information to ASUS. They replaced allegedly the mainboard. But I actually think, they just fixed the connector in place, because bending the phone to a certain degree "unfixed" it in my case again. I dont know, if its the same issue you have, but if it is, hope it helps everyone.
Click to expand...
Click to collapse
Good tip and glad it worked - this could help a few out there. Perhaps ASUS should have included some instructions explaining how to press/bend the device back in order when it happens ...

I had the same issue and quickly found a fix. I bought a OnePlus 9 Pro and relegated this glitchy piece of junk to my desk drawer. Good riddance.

nickdagriff said:
I had the same issue and quickly found a fix. I bought a OnePlus 9 Pro and relegated this glitchy piece of junk to my desk drawer. Good riddance.
Click to expand...
Click to collapse
Paying over $2,000 for a OnePlus 9 Pro seems like an expensive solution, but I am glad it worked out for you. Best of luck over there.

r0me5 said:
Hello, I had a similar issue.
My sim-cards wouldnt be recognized, sometimes only one of them, sometimes both. Additionally, my fingerprint-sensor wasnt working too. By checking pictures of a disassembled phone I could locate the problem inside. It has a connector on the lower end of the phone, which is for sim and FP-sensor. I can definitely and easily come loose.
Quick and dirty fix for me, was pressing with controlled but quite some force on the lower end of the LED-Rog logo while the phone laying flat on the table. I used my thumb, pushed and restarted the phone to check. Didnt work, pushed a bit harder and restarted again until it worked. The back glass has some flex to it, to make it possible to push the connector back in. Still, be careful to not break it, if you try it yourself.
When I found that solution, I've sent it in on warranty for proper fixing with this Information to ASUS. They replaced allegedly the mainboard. But I actually think, they just fixed the connector in place, because bending the phone to a certain degree "unfixed" it in my case again. I dont know, if its the same issue you have, but if it is, hope it helps everyone.
Click to expand...
Click to collapse
Works like a charm here! Congratz!

Omg worked here too, now I have a Poco F3 AND a revived ROG Phone 5...

.

You are the mvp. I love this phone and using it for almost a year. Suddenly sim no longer detected. I tried everything, unlocked bootloader, update firmware. Hour and hours of trying to revive it. I even called Asus and they said to call the Chinese warranty support. Then finally came across this thread. Pressed down hard on the lower end of the logo of the phone on its back. Restarted and now it's detecting the sim again. Thank you so much