Database Info

[Help] Galaxy Note 10.1, 2012 edition not powering on at all. Stock

I have a stock Galaxy note 10.1 NT8010, i hadnt used it in a few days. Went to power on and wouldnt boot. Thinking it was dead i charged it for a few hours and still wouldnt turn on. The power brick is fine, i bought a new stock cable, just waiting for that to come and rule out the cable. But its stock android no rooting or anything.
Any ideas?

Battery shows as charging ??
Odin mode ??? or Recovery Mode ???

JJEgan said:
Battery shows as charging ??
Odin mode ??? or Recovery Mode ???
Click to expand...
Click to collapse
Thanks for replying. Screen is completely dead not even a backlight.
For odin to work would i have to have it rooted previously?

For odin to work would i have to have it rooted previously?
No it does not require root .

JJEgan said:
For odin to work would i have to have it rooted previously?
No it does not require root .
Click to expand...
Click to collapse
Ok, so the pc is not picking it up at all.
I took off the back cover, disconnected the battery and reconnected.
Plugged it into the charger while the cover was still off. On the top left its making a "ti-ti-ti" noise while plugged into power.
Im guessing the motherboard/battery/screen are/is dead. Well one of the 3.
Any ideas?

amsung Tab GT-N8010 Rom doesn't Install, PIT issue, Flashing Screen, do not turn ON
I have Samsung Tab GT-N8010
When I try to turn on, its screen flashing White for half second and then Black and Continuosly till the Battery End.
I try to Install ROM 4.4.2 with ODIN 3.10.7 and get this error
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried different PIT files including 3 different N8010.pit and 8013.pit and 8020.pit
but the issue remaining same
I read all the google search including Russian websites at-least but I couldn't find the issue
I have original cable
EMMC Corrupted may be
I need Solution plz help if anyone can

rehansonu said:
amsung Tab GT-N8010 Rom doesn't Install, PIT issue, Flashing Screen, do not turn ON
I have Samsung Tab GT-N8010
When I try to turn on, its screen flashing White for half second and then Black and Continuosly till the Battery End.
I try to Install ROM 4.4.2 with ODIN 3.10.7 and get this error
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried different PIT files including 3 different N8010.pit and 8013.pit and 8020.pit
but the issue remaining same
I read all the google search including Russian websites at-least but I couldn't find the issue
I have original cable
EMMC Corrupted may be
I need Solution plz help if anyone can
Click to expand...
Click to collapse
same problem here! need help!!!!!

rehansonu said:
amsung Tab GT-N8010 Rom doesn't Install, PIT issue, Flashing Screen, do not turn ON
I have Samsung Tab GT-N8010
When I try to turn on, its screen flashing White for half second and then Black and Continuosly till the Battery End.
I try to Install ROM 4.4.2 with ODIN 3.10.7 and get this error
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried different PIT files including 3 different N8010.pit and 8013.pit and 8020.pit
but the issue remaining same
I read all the google search including Russian websites at-least but I couldn't find the issue
I have original cable
EMMC Corrupted may be
I need Solution plz help if anyone can
Click to expand...
Click to collapse
Same problem here!!!! Service center says Motherboard replacement!!! Please help.

Samsung Tab GT-N8010 Rom doesn't Install, PIT issue, Flashing Screen, do not turn ON

I have Samsung Tab GT-N8010
When I try to turn on, its screen flashing White for half second and then Black and Continuosly till the Battery End.
I try to Install ROM 4.4.2 & 4.1 also with ODIN 3.10.7 and get this error
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried different PIT files including 3 different N8010.pit and 8013.pit and 8020.pit
but the issue remaining same
I read all the google search including Russian websites at-least but I couldn't find the issue
I have original cable
(Internal Partition Corrupted I think (EMMC Error))

I am waiting for useful solution. Anyone can help me here?

rehansonu said:
I am waiting for useful solution. Anyone can help me here?
Click to expand...
Click to collapse
same problem here, have you fix it?

rehansonu said:
I am waiting for useful solution. Anyone can help me here?
Click to expand...
Click to collapse
Have you odin the firmware and apply the pit at the same time?, Plus you shouldn't use pits for other models (ie 8013,8020)

How much storage do you have?

Help!! PIT FILE

Hi,
try to restore my N8013 with stock firmware, get odin error " There is no PIT partition."
how can I get pit file for my device
how to install with ODIN?
can't connect kies, except download mode tablet is dead, only i see "Firmware upgrade encountered an inssue. Please Select recovery mode in kies and try again" What can i do to save my device?
Please help. I'm noob here. I really need some guidance. thanks

Search is what you can do PIT file .
https://forum.xda-developers.com/search/forum/1737?query=PIT

JJEgan said:
Search is what you can do PIT file .
https://forum.xda-developers.com/search/forum/1737?query=PIT
Click to expand...
Click to collapse
Thanks bro
can any one help me with official rom with 5 files (pit ,pda ,phone, csc ,bootloader) ?

Dannirm said:
Thanks bro
can any one help me with official rom with 5 files (pit ,pda ,phone, csc ,bootloader) ?
Click to expand...
Click to collapse
Usual place
sammobile or samsung-updates .

i found the rapair firmware in this page
http://www.tsar3000.com/Joomla/inde...ader-csc-pit-files&catid=55:samsung&Itemid=82
But the pit file does not come in there, so i found the pit file in this link https://forum.xda-developers.com/showthread.php?t=2268735
i put the files in odin and FAIL
ODIN ERROR:
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_N8013UEUCMI3_813049_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_N8013UEUCMI3_813049_REV00_user_low_ship_.tar.md5 is valid.
<OSM> CSC_XAR_N8013XARCMI3_813049_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Set PIT file..
<ID:0/012> DO NOT TURN OFF TARGET!!
<ID:0/012>
<ID:0/012> Re-Partition operation failed.
<ID:0/012> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Someone has an idea what's going on
Thanks. have a good day!

Wrong PIT as repartition has failed would be my first choice .
Sent from my SM-N930F using XDA-Developers Legacy app

Odin Failing to flash stock firmware

Hey all,
Tried flashing back to stock firmware using my Galaxy S4 GT-I9505 using Odin but im getting this error relating to a pit file. I have googled it and downloaded a few pit files for the specific phone but its still not working.
I have flashed previous devices with this flash tool before with no issues usually just have to click AP and browse to the selected firmware click start and shes golden and it works no dramas. However with this device im having soo much bad luck. I have tried to pull my pit file using Miracle box however that doesnt work either, Ive also tried to pull it using ADB but I need ROOT and I dont have it on this device either. I have also tried to root with odin too and I get the same error. is there another program that I can use to pull my own pit file?
I have copied the Odin Log for a reference so hopefully someone can shed some light on this annoying issue cheers.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7105TDVUEMK2_N7105TXSAEMK3_N7105TDVUEMK3_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)

Gear s2 (SM-R720) stuck in download mode (not wireless)

I have this gear s2 stuck in download mode and when I try to flash the firmware on it with Odin (I have already soldered the USB cable on the pins), I get "Re-Partition operation failed" what I can do?

Huh
Kirito821 said:
I have this gear s2 stuck in download mode and when I try to flash the firmware on it with Odin (I have already soldered the USB cable on the pins), I get "Re-Partition operation failed" what I can do?
Click to expand...
Click to collapse
What pins. I got tthe same problem as you m8

notupus said:
What pins. I got tthe same problem as you m8
Click to expand...
Click to collapse
The pins on the motherboard
https://i2.wp.com/electrovo.co.uk/w...msung_s2.jpg?fit=991,707&ssl=1&resize=350,200

Ok
So how did you connect the pins? I cn try on mine to see what works.

notupus said:
So how did you connect the pins? I cn try on mine to see what works.
Click to expand...
Click to collapse
USB cable with the end cutted off and after stripping the wires (usually the colors of the wires are Black=GND, Red=VCC, White=RX or Data + and Green=TX or Data -), I putted some solder on the wires (not too much) and then soldered them on the pins following the same color as the picture that I sent earlier

If re-partition blbla... then something is wrong with PIT (partition.pit)...
A.
You have SM-R720X... Live Demo Unit
Check Back Cover/Rear Case...
B.
You have wrong Firmware on device... so wrong PIT
You can dump PIT from device...
C.
You use wrong Firmware...
So which Firmware you have tried?
Filename and/or Link?
D.
You could flash without PIT... so without CSC for tests...
Combination Firmware have PIT insdie tooo...
So again question...
Filename and/or Link to identify what you are trying...
Best Regards

adfree said:
If re-partition blbla... then something is wrong with PIT (partition.pit)...
A.
You have SM-R720X... Live Demo Unit
Check Back Cover/Rear Case...
B.
You have wrong Firmware on device... so wrong PIT
You can dump PIT from device...
C.
You use wrong Firmware...
So which Firmware you have tried?
Filename and/or Link?
D.
You could flash without PIT... so without CSC for tests...
Combination Firmware have PIT insdie tooo...
So again question...
Filename and/or Link to identify what you are trying...
Best Regards
Click to expand...
Click to collapse
A.
Mine is only SM-R720 without the X at the end
B.
I don't remember what firmware is on device
How can I dump PIT?
C.
I tried R720XXU2BPA4/R720OXA2BPA4 and R720XXU2FRC1/R720OXX2FRC1
Both firmware: https://mega.nz/#F!6MNFkIBA!4e-4_3EFb8aaw20KV01kaw!DQ9iACiS (from this thread https://forum.xda-developers.com/gear-s2/general/gear-s2-r720-frimware-collection-t3857938)
D.
Same error even without CSC

In Odin you see something like GET PIT or SET PIT...
SET PIT means writing...
GET PIT means using PIT from device without writing...
Somewhere is Thread where users wrote about dead eMMC... maybe also in worst case scenario...
Dump PIT...
A.
As Tool I know only cr. Z3X Samsung Tool...
B.
You could sniff USB via Tools... during Odin use...
C.
If Download wireless is alive...
You can sniff via few Commands...
Ehm... At the moment limited time... to search Links for you...
Is this your SM-R720 ?
And you saw it alive?
Or you have this only seen in half dead condition?
Oh, btw... did you tried Combination Firmware?
D.
https://forum.xda-developers.com/gear-s2/general/r720-r732xxu2eqj2-r720xxu2aoj2-firmware-t3760719
Collection of Combination Firmwares...
E.
If next time Odin attempt...
Copy and Paste Odin output... is only text... or make Screenshot...
Best Regards

adfree said:
In Odin you see something like GET PIT or SET PIT...
SET PIT means writing...
GET PIT means using PIT from device without writing...
Somewhere is Thread where users wrote about dead eMMC... maybe also in worst case scenario...
Dump PIT...
A.
As Tool I know only cr. Z3X Samsung Tool...
B.
You could sniff USB via Tools... during Odin use...
C.
If Download wireless is alive...
You can sniff via few Commands...
Ehm... At the moment limited time... to search Links for you...
Is this your SM-R720 ?
And you saw it alive?
Or you have this only seen in half dead condition?
Oh, btw... did you tried Combination Firmware?
D.
https://forum.xda-developers.com/gear-s2/general/r720-r732xxu2eqj2-r720xxu2aoj2-firmware-t3760719
Collection of Combination Firmwares...
E.
If next time Odin attempt...
Copy and Paste Odin output... is only text... or make Screenshot...
Best Regards
Click to expand...
Click to collapse
I can't access Wireless Download because when I try to go in reboot menu the screen glitch and then boot on Download Mode
I only have seen this in half dead condition
Bought it some weeks ago in the hope to repair it
I tried the Combination Firmware but fails to install
Log from Odin:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 908 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
EDIT:
I retried with only BL and AP (R720XXU2BPA4), this time says that there is no PIT partition
Log from Odin:
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 1214 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)

https://forum.xda-developers.com/gear-s2/general/fail-to-hard-softreset-t3746359
https://forum.xda-developers.com/gear-s2/help/gear-s2-wont-perform-factory-reset-t3737448
Here you can find...
Some """write protection""" hints... eMMC...
No idea if Hardware or Software related...
If you have in Reboot menu...
Upload
You could try to use RDX Tool:
https://forum.xda-developers.com/showpost.php?p=72110199&postcount=45
Please try Combination Firmware... this is Service Factory stuff... maybe it helps...
Next attempt is to force Odin... to use PIT...
Which Odin Version you use?
Best Regards

adfree said:
https://forum.xda-developers.com/gear-s2/general/fail-to-hard-softreset-t3746359
https://forum.xda-developers.com/gear-s2/help/gear-s2-wont-perform-factory-reset-t3737448
Here you can find...
Some """write protection""" hints... eMMC...
No idea if Hardware or Software related...
If you have in Reboot menu...
Upload
You could try to use RDX Tool:
https://forum.xda-developers.com/showpost.php?p=72110199&postcount=45
Please try Combination Firmware... this is Service Factory stuff... maybe it helps...
Next attempt is to force Odin... to use PIT...
Which Odin Version you use?
Best Regards
Click to expand...
Click to collapse
Tried flashing Combination Firmware with Odin 3.12.3 and Odin 3.13.1 but nothing, it always fails

For outdated SM-R720/SM-R732 no need of newest Odin...
https://forum.xda-developers.com/showpost.php?p=72049726&postcount=100
Try to find Tutorial to set PIT manually...
RE-PARTITION
PIT you can take from CSC or inside Combination Firmware...
Best Regards
Edit 1.
My fault...
https://forum.xda-developers.com/showpost.php?p=72098729&postcount=114
Seems I have successfully used Odin 3.12.3

adfree said:
For outdated SM-R720/SM-R732 no need of newest Odin...
https://forum.xda-developers.com/showpost.php?p=72049726&postcount=100
Try to find Tutorial to set PIT manually...
RE-PARTITION
PIT you can take from CSC or inside Combination Firmware...
Best Regards
Edit 1.
My fault...
https://forum.xda-developers.com/showpost.php?p=72098729&postcount=114
Seems I have successfully used Odin 3.12.3
Click to expand...
Click to collapse
Tried with PIT set manually but it fails both Combination Firmware and R720XXU2PBA4
Log from R720XXU2PBA4:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Log from Combination Firmware(R720XXU2AOJ2):
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Kirito821 said:
Tried flashing Combination Firmware with Odin 3.12.3 and Odin 3.13.1 but nothing, it always fails
Click to expand...
Click to collapse
If you want I can send you my motherboard for you to try in. So you can troubleshoot to see if it is your mobo or something else. I'll send you a stripped wire too so you do not have to use your own.

When I was trying flashing again, the watch fallen from the desk and for instinct I grabbed the cable and the pad for GND and RX broke up
Thank you for your time and help in troubleshooting adfree :good:
And thanks notupus for the thought in helping me :good:

Kirito821 said:
When I was trying flashing again, the watch fallen from the desk and for instinct I grabbed the cable and the pad for GND and RX broke up
Thank you for your time and help in troubleshooting adfree :good:
And thanks notupus for the thought in helping me :good:
Click to expand...
Click to collapse
So gnd is the metal part and i'l looking for rx

Long time ago I have ripped off my Gold pad for Data -
http://forum.gsmhosting.com/vbb/12484681-post5.html
The white point in my Picture...
Best Regards

Someone please compile a zip file and maybe a pcb dezign with pogo pins

I'm also stuck with 'Re-Partition operation failed'. Did anyone find a solution for this problem?

I have a problem, I tried to unbrick my GEAR S2 720 and now it says "Firmware upgrade encountered an issue. Please select recovery mode in KIES & try again". I tried unpluggin the battery, but same problem. I think it will be bricked 4ever