Hello,
the bottom connector from my Himalaya is broken...
Does anybody knows if there is a sync-cabel for the back-side connector ?
Or a female plug (perhaps from a cable extension) would help me to solve the problem as well...
Thanks in advance!
I have exactly the same problem. Any advice on where to find that connector. I can't take to a authorized service, because there's none in Macedonia
Thanks
Hey guys, can anyone help please. At least if you can tell me where to find that connector on the internet, so I can change it.
I think it's the same connector as for the IPaq 3800 series, can anyone confirm that. Thanks
ATC
go to www.merconline.co.uk for xda2 parts very good for conector repairs
was you finding that cable. I am also searching it, pls tell from where i can get it. i also not sure is it for synch and to charge xda.
cant you charge just the battery on the xda dock?
and sync with bluetooth?
flyboy
but problem is this i cant flash through bluetooth
Exactly same?
I have a Himalaya(i-mate Pocket PC) with a broken USB , repalaced by only a charging port so that I can charge it but cannot flash it! Got the intact cradle though. Is there anyone who can repair my USB port so I can flash it again?
this happenend on My first Himalaya too,i´ve searched a lot through the Net
and couldn´t find any spare parts,what I want to say is...
theres a bigger Problem to find Spare Parts then to solder the Port to the board
(yeahyeah...which isn´t easy too..i know...)
But is there anyone who knows what is the backside connector? And is there cable for it?! It will be good to use it! Just to avoid, soldering and finding spare parts! Any info will be good! I have soldered mini usb 2 times and every time i do that after fall it came of! I'm sick of soldering!!!
MMMMMM That`s it!!!
Look all!!!
The backside connector isn`t for syncornizing an charging!!
It`s just for connecting the "High capacity" battery, you know the big battry with 2400 mAh.
All i want to say, you have to put a new connector to flash roms and charge the battery without take it off from your devices.
Hope i`ve help you with you problem!!!!
Noaman Atassi
I knew that! But if u open a himalaya, and if u see below the back side connector there is a number of small dots, and every single of them are corespondenting for ones where the connector was soldered... So if anyone can find a corespodence for usb connection that will be good project... Just to avoid a use of old and crapy original connector, then u can use any connector u want! (for about 4 pins which is need for charge and usb sync) !!!!
Check this thread http://forum.xda-developers.com/showthread.php?t=636549
G'day all
I'n need of desperate help as my serial port is stuffed, can someone please tell me if the male part of the connector is available to buy anywhere?
I know this is a tricky soldering job but a good friend has offered to help
Also I notice the rear backpack connector appears to route thru the same pins, does anyone know if this could be used to charge and sinc the phone, and if a connector is available.
Sorry for the gimme questions but I've searched all this site and many more with no luck.
hi guys does anybody no where to get the black signal cable from? cant find it anywhere, had to pinch one to sort a phone out thinking they would be easy to find!!
Hello Team,
i want to root my new firetv, using emmc connecting method. i ordered the maximus low-volt adaptor and the transcent sd adapter.
i soldered the low-volt adapter ( really...really. small parts ! a very hard job....blue led is working )
then i opened the firetv and i am was wondering about the pcb layout .. it is completely different like on the pics in the net
.does anybody have the solder points for this ( Firetv Board DV83YW )
i am too new here for posting pictures links , sorry .. but per mail no prob.
greets
mike
mike1001 said:
Hello Team,
i want to root my new firetv, using emmc connecting method. i ordered the maximus low-volt adaptor and the transcent sd adapter.
i soldered the low-volt adapter ( really...really. small parts ! a very hard job....blue led is working )
then i opened the firetv and i am was wondering about the pcb layout .. it is completely different like on the pics in the net
.does anybody have the solder points for this ( Firetv Board DV83YW )
i am too new here for posting pictures links , sorry .. but per mail no prob.
greets
mike
Click to expand...
Click to collapse
Greetings and welcome to assist. It looks like you have found the correct place to ask your question here
https://forum.xda-developers.com/showthread.php?t=3551710
so I'll close this one up
Good Luck
Sawdoctor
Hi,
My problem is that I have USB headphones, and when I connect an USB OTG cable to my phone it doesn't work. I tried an application called "revolution otg" and then I saw red light on my headphones, but sound plays on speaker of the phone. Any ideas?
P.S. sorry for bad English ;p
Gronie2014 said:
Hi,
My problem is that I have USB headphones, and when I connect an USB OTG cable to my phone it doesn't work. I tried an application called "revolution otg" and then I saw red light on my headphones, but sound plays on speaker of the phone. Any ideas?
P.S. sorry for bad English ;p
Click to expand...
Click to collapse
Hello & welcome to xda-assist,
you have the advantage that your device has a wonderful device specific thread so I recommend to you to go there and ask the guys there who own this device too...
Good luck
https://forum.xda-developers.com/huawei-p9lite/help