Database Info

[GUIDE] [ROOT+CWM] [UNROOT] Iberry Auxus One (SPFT Method)

*****Root with SPFT Flash Tool Method*****
for iBerry Auxus One
[EASY ROOT METHOD]
Guys. Now we have our own first Root Method for AUXUS ONE STOCK ROM.
This method is successfully tested by me on Windows 7.
For more help visit this FB page too.
https://www.facebook.com/groups/AuxusOne/​
Installation Instructions
Warning: Do at your own risk. Disconnection due to poor cable or Electricity Supply failure can still brick your phone beyond repair. This also breaches warranty of your phone. I am not responsible for any damages.
Disable Antivirus so that it cannot interfere with the flashing process
1) Download flashable zip file named UPDATE-SuperSU-v2.40.zip and save in root of your SDCard
2) Download and extract the Auxus ONE CWM Recovery Flash Package on desktop or anywhere on your pc.
Install Phone Driver (From the Driver folder you have just extracted).
3) Download and Install ADB Driver Installer for Windows (important) while installing connect phone to pc and let is recognize .
After driver installation is done disconnect phone from pc and reboot your pc.
4) Run as Administrator the "Flash_Tool.exe" from SPTools folder inside that folder you extracted.
5) Keep only One File checked (selected) as shown in following image (Recovery.img). If options are not seen then click on "Scatter-loading" button at top-right side and select "One_MT6592_Android_scatter.txt" file from extracted folder. Now be sure only one options (RECOVERY.IMG) selected as mentioned in following image. Unselect all other options.
Now PRESS "Download" button at top.
6) Remove battery and memory card from phone and connect PHONE to pc with usb cable. Now pc should recognize phone and flashing should start in a minute. Look at process bar in image below. WAIT WITH PATIENCE.
After flashing is done, the GREEN tick mark will be shown as shown in image below.
7) Now close program on pc and remove cable, Insert Battery and start phone in RECOVERY mode.
To start phone in recovery mode press "VOLUME UP" button and "POWER" when Auxus Logo appears release "POWER" button keeping "VOLUME UP" button pressed until phone starts in CWM Recovery mode.
8) Important: Now install/flash "UPDATE-SuperSU-v2.40.zip" in Recovery mode and Reboot phone in system (normal) mode
Done. Enjoy Press :good: thanks if you liked my work.
IMPORTANT: The package also contains original Stock Recovery named recovery_org_stock.img. If you want to flash back to original company stock recovery, then select this file in flashing tool (Click recovery line and select this file) and then flash.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Auxus One Unroot Process
For Auxus One Unroot Process Follow the Below Steps
1. Open SuperSu app in your mobile >Setting > Unroot. (Phone will restart and SuperSu & Su binaries will be uninstalled)
2. Flash Stock Recovery by following above root guide from step 1-6 (leave drivers installation part in case drivers are already installed).
3. In above step 5, select recovery_org_stock.img instead of recovery.img file
Thats all, now your phone is unrooted and you can do OTA Update.
Press Thanks button if you like this post!

--- Post reserved for stock recovery process----

fix heating problem help
Dear all pls help me how can i fix heating problem Iberry Auxus One

I have taken the auxus one too , is there any seperate forum for auxus one by any chance ?

rohail009 said:
I have taken the auxus one too , is there any seperate forum for auxus one by any chance ?
Click to expand...
Click to collapse
There is an group for Auxus One on fb for all types of queries, reviews, development related stuff
https://www.facebook.com/groups/AuxusOne/

Kaymart said:
Dear all pls help me how can i fix heating problem Iberry Auxus One
Click to expand...
Click to collapse
Under clock its cpu speed

amarbunty said:
For Auxus One Unroot Process Follow the Below Steps
1. Open SuperSu app in your mobile >Setting > Unroot. (Phone will restart and SuperSu & Su binaries will be uninstalled)
2. Flash Stock Recovery by following above root guide from step 1-6 (leave drivers installation part in case drivers are already installed).
3. In above step 5, select recovery_org_stock.img instead of recovery.img file
Thats all, now your phone is unrooted and you can do OTA Update.
Press Thanks button if you like this post!
Click to expand...
Click to collapse
Hi,
Thanks for your help. But bad news for me. CWM recovery img is not working in my auxus one. even stock img also not working.
Now recovery mode is empty . i cant enter into recovery mode please help me

amarbunty said:
Under clock its cpu speed
Click to expand...
Click to collapse
Please help me. need recovery image to flash. Right now i don't have any recovery mode. Stock recovery is deleted,

Request
Pls any one upload custom rom (MIUI) for iberry auxus one......

(UNLOCKED BL) ROOT Sony Xperia M2 on Android 5.1.1 [FULL-ROOT]

Hello guys!
Today I'm bringing you a tutorial on how to achieve root permissions on the Xperia M2 with Android 5.1.1 Lollipop. As of right now, this is only available for UNLOCKED BOOTLOADERS, so those with LBL have to wait a little more until I find a suitable solution.
What do we need?
Upgrade your bootloader using this guide.
My ADB pack.
My modded TWRP for unlocked bootloaders.
Ric Disabler by my friend @AleksJ [MIRROR]
The procedure:
First, flash Lollipop if you didn't flash it before. Once done, upgrade your bootloader using Emma or the FTF I linked before.
WARNING: If you updated your bootloader BEFORE FLASHING LOLLIPOP, you MUST upgrade it again since Lollipop FTF overwrites it.
Now, turn on the phone, go to Settings, Info. about the device, and tap 7~8 times the Compilation Number. This will un-hide the developer options. Press back button once and go inside the Dev. Options. Now turn them on if they were off, and enable USB Debbuging. Now turn off your phone.
Now, unzip my ADB Pack 'Herramientas-de-flasheo.zip', which contains basic ADB and Fastboot executables to a folder in your desktop. Also, copy the TWRP Recovery .img you downloaded to that folder.
Put your phone in Fastboot mode, this means, while pressing and holding the Vol+ button, connect the USB cable. Once the Led goes blue, stop pressing it.
Now, execute the following keyboard shortcut (Win+R) and type inside the Run prompt CMD. Inside the Command Prompt, using CD (change directory), navigate to the folder you created in the desktop. It'll be something like...
Code:
cd C:\Users\linuxct\Desktop\adbpack\
Now, execute the following command:
Code:
fastboot flash recovery [COLOR="DarkOrchid"]RECOVERY-TWRP-2.8.7.0-D230X_D240X-UPDATED-THEME[/COLOR].img
Once it finishes, disconnect the USB cable. Now, to enter into the recovery, press and hold the volume down button, and while you're holding it, press and hold the Power button until it vibrates. When you see the BIG Sony logo, stop holding the Vol- Button.
This will load Erikcas TWRP. After few seconds, it'll ask you to allow /system modifications, so slide it to allow modifications. Now navigate to Reboot, and choose System. In a moment or so it'll ask you if you want to root your device. To do that, slide again.
The device will reboot in a few seconds. When it's succesfully booted up, go to the App Drawer and look for 'SuperSU Installer'. Open it and hit the 'Play' button. This will open SuperSU in Google Play. Now update SuperSU.
When it's done updating [Don't open SuperSU yet!], unzip the Ric Disabler from AleksJ in your PC, and open the Install.bat OR Use the following Bash Script if you're on Linux, thanks to @luichi. Once it's opened, connect again your device via USB. In the M2, the script will prompt a question about USB Debbuging key. Tick the 'Remember this PC' checkbox and hit Allow. After some secs, it'll ask you for root permissions, so hit Allow.
In a while, when in CMD it says 'Press any key to continue', disconnect your cable and open SuperSU in your device. Now it'll ask you about updating su binary. Hit Update, and then hit on 'Normal' method.
And that's it! Enjoy your Lollipoped device with Root!
Don't forget to hit the thanks button and thank all people mentioned in this post too!

Thanks for this tutorial! All working

Can you make bootloader in FTF file for D2305 plz? Thanks!

Thanks
Do you know if Xposed is fully working?

Laura158 said:
Can you make bootloader in FTF file for D2305 plz? Thanks!
Click to expand...
Click to collapse
It's generic, don't worry, you can use it in any D230X and any D240X you want.

KolikKitsune said:
Thanks
Do you know if Xposed is fully working?
Click to expand...
Click to collapse
I have no idea...

KolikKitsune said:
Thanks
Do you know if Xposed is fully working?
Click to expand...
Click to collapse
@KolikKitsune for me nope. i might do something wrong but its saying with the current version it doesnt work
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

It is only for M2 or for Aqua too?

Evedammo said:
It is only for M2 or work in Aqua too?
Click to expand...
Click to collapse
Aqua too! Any M2 in general can use it :good:

via emma ? can you show how upgrade bootloaders via emma ?

WoW, nice work. Have a fully working recovery AND root now.
If you want something "simpler", you can flash a boot.img with integrated recovery instead of using the first method.

BlazingBullets said:
WoW, nice work. Have a fully working recovery AND root now.
If you want something "simpler", you can flash a boot.img with integrated recovery instead of using the first method.
Click to expand...
Click to collapse
But then you'll need to go back to 5.1.1 kernel in order to boot the device, loosing the recovery. This recovery is permanent as it's isolated in it's own partition.

faizal21 said:
via emma ? can you show how upgrade bootloaders via emma ?
Click to expand...
Click to collapse
Follow this nice guide made by Sony

vampirian said:
@KolikKitsune for me nope. i might do something wrong but its saying with the current version it doesnt work
(img)
Click to expand...
Click to collapse
Guys, you need to install the experimental Xposed for Lollipop 5.1.1! The 4.x installer is not working anymore!
BUT, take this into account:
- Sony seems to have shipped some ROMs with corrupted services.odex (the embedded .dex is invalid). Those ROMs will bootloop with a "Fatal signal 6" or "No pending exception expected: java.lang.ArrayIndexOutOfBoundsException" error, which I unfortunately cannot fix.
Click to expand...
Click to collapse

@linuxct
I dunno if I flashed back or not, but if i didn't then I think FKernal works with 5.1.1
Don't really want to test it either

Guys dont even try xposed...Bootloop because of corrupted services.odex

Too late... -.-

after Flashtool by sony
after taht, what the next step ?

faizal21 said:
after taht, what the next step ?
Click to expand...
Click to collapse
After flashing the bootloader update, turn the phone on, enable USB Debugging and then turn it off; and go ahead to flash erikcas twrp. (2nd and 3rd points)...

after step 8 i reboot like normally but touch wont work, but the touch in RecoveryMode work well..

[C2304] Installing TWRP or CWM recovery in the Xperia C

Well, I just purchased this device and came here after that to look at what we had and I'm disgusted.
And there are several reasons for that, being:
1 - Locked Bootloader...
2 - This forum seems somewhat abandoned, which leads it to be somewhat disorganized.
EdiT:
Thanks to our friend repey6 > http://forum.xda-developers.com/member.php?u=5704037
TWRP 2.8.7.0 is now included, and it works just ok, with all functionality.
I strongly recommend you to use it instead of any other recovery. Just make sure to backup your ROM again after installing it, as CWM or Carliv backups won't work in TWRP.
I replaced the old TWRP included in the attachments with the new one provided by repey6, but the installation process remains the same.
Plus, this was not created by me and it's mad old (2014). But still it works better than the Carliv Recovery we have available here...
So Let's go. The proccess is the same for both, just choose the recovery image you want in the end of the topic.
(almost forgot to say that if your phone bricks it's you responsibility, I tested it in mine and it is working fine)
STEPS:
STEP1- Root your phone (if it's not rooted yet).
To root your phone you'll need to:
a-Download the framaroot APK provided in the attachments
b-Install it then click in the Boromir option and the su binary will be installed.
c-Download SuperSU from google play store.
That's all, simple like that.
STEP2- Check your bootloader's S1 Version
a-Open your dialer and input *#*#7378423#*#* , then go to Service Info>Software Info> S1 Boot Version.
b- Check if yours is 2.14.J.2.6 or 2.14.J.2.13 or 2.14.J.2.16 . If yours is one of these go ahead, it should work just fine and you can proceed.
If yours is 2.14.J.0.68 do not proceed, as it will 100% brick your phone.
c- My phone has S1 Boot Version 2.14.J.1.15 and in spite of the developer having not mentioned anything about it, I risked it all and my phone flashed the recovery normally, so if your version is also 2.14.J.1.15, it should work just fine and you can proceed.
STEP3 - Install the recovery
NOW, BE EXTREMELY CAREFUL HERE, OTHERWISE YOU WILL HARD BRICK YOUR PHONE:
a-Download the mobileuncle.apk file provided in the attachments and install it.
b-Download the twrp_xperia_C.img file provided below and put it in your internal memory (not on the external). Rename it to recovery.img, otherwise mobile uncle won't see it.
Now, here's the part you have to mind, so you won't brick your phone.
Mobile uncle can install a recovery using one of two methods. One is by installing the image from your internal memory (which we'll be doing). Other is installing it from the internet.
Now, YOU DON'T WANT to install a recovery from the internet, as mobile uncle doesn't provide any image for your device. So if you flash any of these recoveries, you'll never be able to make your phone boot again.
See in the image below and you'll get what I mean:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
c - So, before proceeding TURN OFF YOUR WIFI AND DATA CONNECTIONS so that mobile uncle won't show any recovery from internet
d-Open mobile uncle.
e-Grant Super User
f-Press "Recovery Update"
g- With wifi turned off, you'll see only your recovery in the screen
h- Click it, the file size of the file I'm posting must be around 6MB ( 6210KB for CWM), if it's different cancel and download file again.
i- press ok and restart.
DONE
:good:
EDIT:
I just noticed that after flashing the recovery you might get your phone stuck in the SONY logo after it.
In fact it happened to me, but just once.
If that happens don't panick. Recove the cover of your phone and besides the SIM-2 slot you'll see a tiny role with the word "reset". Insert a needle in there and your phone will restart normally.
CREDITS FOR CWM
Prashanth Jraj
Credits for posting it on the net and for the original tutorial:
informationlord.com
credits for TWRP 2.8.7.0
Miha_xXx
Original Post (for TWRP - in Russian): Click Here
credits for this tutorial:
me
ATTACHMENTS BELOW

Thanks for the guide! Does this also work on the C2305 model, or is it strictly for C2304?

Syd_M said:
Thanks for the guide! Does this also work on the C2305 model, or is it strictly for C2304?
Click to expand...
Click to collapse
It should work in both, I'm using a recovery for C2305 in my C2304.
Just don't try flashing a C2305 ROM on your C2304. It will not hardbrick your phonw, but the SIM cards will not work and you will get a mad functioning phones.
Some custom ROM's based on stock firmware work in both though.

Hey anyone tried for xc 2305???

So my S1 bootloader version is: 2.14.J.0.68. Is it for sure there is nothing that can be done?

SMIT120 said:
Hey anyone tried for xc 2305???
Click to expand...
Click to collapse
sid4913 said:
So my S1 bootloader version is: 2.14.J.0.68. Is it for sure there is nothing that can be done?
Click to expand...
Click to collapse
Sorry for the late reply! Haven't been able to test this until recently due to an issue getting my PC to work properly with my phone. Anyway, I would like to confirm that I was able to flash this on my Xperia C2305 that had S1 Boot Version 2.14.J.0.68. The photo below is proof of CWM running on my Xperia C2305:
Things you will need:
WMShua SuperFlash: http://soft.flushrom.com/WMShuaSetup.exe (after installing, you can change the language to English by renaming Program Files/wmshua/language to Program Files/wmshua/language_x)
Xperia C 16.0.B.2.16 FTF: C2305_16.0.B.2.16_TacoNikky.ftf or C2305_16.0.B.2.16_Congngheviet.ftf (pick one; I used TacoNikky's version)
Procedure:
1. Open WMShua, then click on Flash (not Super Flash). Browse to the FTF file you downloaded. You can choose to backup system before flash (I unchecked it on mine). Follow the screenshot below for guidance:
2. Turn off your phone. Next, hold down the Vol- (volume down) button on your phone. While holding down, plug in the micro USB cable. The LED will flash red. When it changes to green, release the Vol- button. WMShua should automatically try to install the needed drivers. After installing drivers, it will begin the flashing process. If your phone turns on instead, simply unplug it from the USB, turn it off, then try again.
The flash process may take a long time (it took 30+ minutes for me), and sometimes it may look like it hanged, but it's actually working. Just be patient. Once it reaches 100%, your phone will automatically boot up. Check your S1 Boot Version—it should now be 2.14.J.2.16. You may find that you've lost root, so you will need to root it again (I use KingoRoot). After rooting, follow the instructions on the first post to install CWM or TWRP. Good luck!

[Root] Telcast X80 Plus root

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Tutorials and the tools are not my work, so I don't take any credit. However, the tutorial is come from China. I combine my experience and translate them as much as I can to english.
Instructions:
First, download the root files (at the bottom of this post) accroding to your tablet model (at the back of your tablet) and install the driver in the computer.
Please install in the following order:
1) iSocUSB-Driver-Setup-1.2.0.exe
2) IntelAndroidDrvSetup1.5.0.exe
3) PhoneFlashTool_5.3.4.0_win32.exe
Pay attention to the following points
a) you must install those driver in the above order
b) Don't change the install location of those driver
c) Close your antivirus software to avoid unknow problem
Then, go to Settings>Developer Options>USB Debugging. Enable OEM Unlock and enable USB Debugging Mode
Now, connect your X80 Plus to the computer,
Open a Command Prompt window in "Root X80 Plus H6C3" folder (To open a Command Prompt window in any folder, hold down the shift key and right-click on the folder) and enter the following command
Code:
adb reboot bootloader
Press Enter
Wait for the device to enter fastboot mode
Code:
fastboot oem unlock
Press Enter to unlock the oem and enter the following command
Code:
fastboot flash boot boot.img
Press enter to flash the kernal, then enter the following command
Code:
fastboot reboot
This command will restart your tablet.
It is normal that tablet reboot 3 to 4 times automatically, just wait for it. (turn on the tablet yourself if the tablet do not reboot automatically)
After your device is on, check that Wifi and bluetooth works or not. (Wifi and Bluetooth may not works with the replaced kernal, just perform a factory reset)
If everything is ok, enter the following command
Code:
root.bat
Wait for the Command Prompt until it stuck at this command, "adb shell su --daemon"
Now, disconnect the tablet and reboot it manuly
After the device was booted up, Supersu already become a part of system app.
Open Supersu now, it will notify that the SU binary needs to be updated. You must need to install the binary once, but you will fail at 100%(unless there is a miracle, and your tablet is root successfully, congratulations)
Close Supersu and reconnect the tablet, enter the following command again.
Code:
root.bat
Now the command prompt should run all of the command smoothly and Supersu should have no message about the SU binary update !!
Therefore, if your Supersu shows nothing (works properly), your tablet is rooted, thats amazing.
If Supersu keep notifing, please enter the following command again and wait for it to boot up automatically until Supersu have no message about the binary update.
Code:
root.bat
Note that this root method are not stable yet
Known issues:
1) Old version of Titanium Backup was unable to execute the SU command
2) LBE are not 100% compatible with this root
Post reply if you have any requires or problem.
Stock Rom for X80 Plus just in case you need them, and the instruction will be translated later
H6C3 and H5C5
Root files: H6C3 and H5C5
Sorry for my bad english

Hi and thanks for sharing.
Is there a custom recovery to install?
I would like to install xposed framework, but don't know how to install the zip file...
Thanks

thanks and your thread on teclast's forum where the link was crash, please repair.

Thanks a lot

Can someone confim that this method works?

Jeconxis said:
thanks and your thread on teclast's forum where the link was crash, please repair.
Click to expand...
Click to collapse
You can try to flash xposed using flashify!

woody4165 said:
Hi and thanks for sharing.
Is there a custom recovery to install?
I would like to install xposed framework, but don't know how to install the zip file...
Thanks
Click to expand...
Click to collapse
Working hard on it now

hahaha1111 said:
Working hard on it now
Click to expand...
Click to collapse
looking forward to this!

Thaaanks a lot @hahaha1111 !!! I tried that on my all new H6C4 received this morning with your H6C3 files and anything is working perfectly !!! Many thanks again !!!
BTW: Any way to update SuperSU binary then?

I tried your method on my H5C6 and it worked beautifully. Thank you!

where can I use the file?
I download the file named X80 plus-win10_20160108.7z from the link. what is this, and where can I use it?

hahaha1111 said:
Working hard on it now
Click to expand...
Click to collapse
Hi @hahaha1111
any news on custom recovery?
I would like to install xposed framework, but cannot be done without custom recovery, is it correct?
Thanks

woody4165 said:
Hi @hahaha1111
any news on custom recovery?
I would like to install xposed framework, but cannot be done without custom recovery, is it correct?
Thanks
Click to expand...
Click to collapse
Hiatus

H6C4
Great! It works perfectly on H6C4.
Thanks!
Regards

RoroTiti said:
Thaaanks a lot @hahaha1111 !!! I tried that on my all new H6C4 received this morning with your H6C3 files and anything is working perfectly !!! Many thanks again !!!
BTW: Any way to update SuperSU binary then?
Click to expand...
Click to collapse
It's updated from play market with no problem.
May be it is my particular problem ( kernel 3.14.37 firmware assembly ver 3.03.20161109) but.....
WARNING TO H6C4 OWNERS! SD Card becomes unusable with this rooting files. Any SD Card after rooting recognized as 0,9 Mb size and you can't access files on it. You can't use SD Card reader too.
Please report if you do not encounter this issue.

Hi.
I'm stuck on "adb push SUfiles/Superuser.apk /data/superuser" command in root.bat
I've done all the previous steps without problems.
Before executing root.bat I have set again Usb Debug and OEM Unlock, is it correct?
Sometimes I get stuck on "adb remount"
What can I check?
Thanks
Woody

How to root Teclast P80 3G K3H7 - Tablet - Android 5.1.1 - Intel SoFIA Atom X3

This is only for Teclast P80 3G K3H7 it won't work on Teclast P80 mediatek or other models check your model on the backside of the cover.​
First, download the zip files provided below and unzip them.​
Ok listen carefully, since you're rooting Android you should be familiar with adb commands and drivers. ​
Follow the instructions carefully steps by steps if you do not want your device to be bricked. I am not responsible for bricked device.​
1 - Power off your device.
2 - Install the factory tool and make sure to create a desktop icon.
3 - Open the factory tool.
4 - Now here's the important part.
5 - Click on firmware tab and load the philz_recovery.fls then click run.
6 - Now connect your device via usb cable and don't press anything.
*** It should show green color if it shows red color then repeat the steps above.***
7 - After that click on stop then close the factory tool.
8 - Now to go to philz recovery you need to hold down the power button and volume up button at the same time.
9 - When you see Philz recovery go to Install zip then choose Install zip from the sideload. This is the only way to root this device so do not choose sdcard it won't work choose sideload.
I know recovery is laggy and touch doesn't work but this is the only way to root this device so you will have to do it with volume buttons. I tried to port TWRP but the touch doesn't work so I ported Philz recovery since Philz work with volume buttons.​
Now to install SuperSu I used SuperSu 2.46 here it's how you do it via sideload. Connect your device to a pc ***make sure it's in adb sideload mode***
Code:
adb devices
adb sideload UPDATE-SuperSU-v2.46.zip
Then hit enter and Just wait until you see installation complete in Philz recovery *** you should be patient since the recovery is laggy*** after that remove usb cable and power off the device by holding down the power button until it's off
NO DO NOT POWER ON YOUR DEVICE IT WILL NOT BOOT UP SO FOLLOW THE STEPS BELOW TO BOOT YOUR DEVICE WITH ROOT ACCESS
​
Now open up factory tool again MAKE SURE YOUR DEVICE IT'S POWERED OFF then reflash the STOCK boot.fls and recovery.fls back. Flash the recovery.fls first then disconnect the usb cable AND POWER OFF AGAIN BY HOLDING DOWN THE POWER BUTTON then flash the boot.fls. Make sure your device it's powered off each time you flash
Now you can boot up your device and see if SuperSu is installed. If you have any trouble ask them below ​

Teclast P80 K3H5
Hello mate, first to say thanks for your tutorial, i really apreciate, because it's really hard to find something good for this device.
I'm using version K3H5 it's based on intel cpu, so just to know there is no problem with that, i can try with your tutorial?
And one more question, it would be nice that you write some more information on last part.
I was trying to root with tool of intel cpu but did not work, i'm not sure that my drivers installed properly, i can't see that showing android device in device manager, just on bottom i have icon on other devices, where is bus devices, icon of adb, but when i wast trying to root with that method it failed, ao how to properly install drivers that i can see them on my pc, i'm using windows 10, please if u can just put soke tutorial or something, just to root this thing because it's really uselese like this, low memory, and really slow when i playing games.
Thanks.

Herceg89 said:
Hello mate, first to say thanks for your tutorial, i really apreciate, because it's really hard to find something good for this device.
I'm using version K3H5 it's based on intel cpu, so just to know there is no problem with that, i can try with your tutorial?
And one more question, it would be nice that you write some more information on last part.
I was trying to root with tool of intel cpu but did not work, i'm not sure that my drivers installed properly, i can't see that showing android device in device manager, just on bottom i have icon on other devices, where is bus devices, icon of adb, but when i wast trying to root with that method it failed, ao how to properly install drivers that i can see them on my pc, i'm using windows 10, please if u can just put soke tutorial or something, just to root this thing because it's really uselese like this, low memory, and really slow when i playing games.
Thanks.
Click to expand...
Click to collapse
If it's Intel X3-C3230 based cpu then use this tutorial. Please use the Factory tools attached above to root this tablet it will automatically install the drivers. If bootloop pls go to this site http://www.teclast.com/en/firmware/ and put your model number (K3H5) and download the rom then flash recovery.fls and boot.fls only AND ONCE AGAIN ONLY USE FACTORY TOOLS TO FLASH. If you have problem post this here I will help you

Hi, for me this solution is not working. It stops when I want to install via side load. Recovery cat create the mount point. It's the k3h6 Version.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

suschmania said:
Hi, for me this solution is not working. It stops when I want to install via side load. Recovery cat create the mount point. It's the k3h6 Version.
Click to expand...
Click to collapse
Is your device Intel based? Pls check with CPU-Z.

Hi, yes it is from Intel. Genuine Intel CPU 4cores codename SOFIA 3GR

suschmania said:
Hi, yes it is from Intel. Genuine Intel CPU 4cores codename SOFIA 3GR
Click to expand...
Click to collapse
Alright I ported Philz Recovery for K3H6 attached below
try this and please report back.
And don't forget to flash back your stock recovery.fls and boot.fls after flashing and rooting. Use K3H6 stock boot.fls and recovery.fls DO NOT USE THE FILES FROM K3H7.
Pls follow the instructions above steps are same.

Thank you very much, i will try this as soon as possible

IT WORKS! No problems at all - thank you for your help!

Thanks! where can I find K3H6 stock boot.fls and recovery.fls? in the teclast page everything is in chinese...

K3H5
suschmania said:
Hi, yes it is from Intel. Genuine Intel CPU 4cores codename SOFIA 3GR
Click to expand...
Click to collapse
posty82 said:
Thanks! where can I find K3H6 stock boot.fls and recovery.fls? in the teclast page everything is in chinese...
Click to expand...
Click to collapse
I need PhilzK3h5 ... where can I download it? Thank you...

Nothing happens during firmware
I've loaded the philz thing into the firmware and clicked run, and then connected the tablet (by usb) to my laptop, but nothing happens, at all. So, the tablet is supposed to be off? Could I keep the tablet in fastboot mode during this?
Thanks

Hi all.
Anyone have firmware for Teclast P80 3G (K3H6)? Please share? Bricked with update. All links dead.

K3H5
Hey, @kaiz16 Could you make philz port for the K3H5 by any chance? I tried with the K3H7 and K3H6 recoveries but it does not boot into recovery at all.