Careful if you're in the Mid West and want to customize a 2015 Moto G. I have had great success with previous variants, but this one (XT1548) won't get back on the US Cellular network. Tried a few nightlies and the release version. No bars show, the status message reads: "Emergency calls only - U.S. Cellular", and when choosing US Cellular as the network operator it times out with: "Can't connect to this network right now. Try again later."
I found this post and was very optimistic that setting the Access Point Name manually would help, but I am unable to actually save the full APN. I can save it after entering the name & APN fields, and several more fields, but at some point when I enter all the data on that page and click Save, the new APN disappears.
I called U.S. Cellular's support number (888) 944-9400 and level two support was able to provide my MIN number but disavowed any knowledge of the remaining APN settings. When they understood that the phone was rooted I was read a dismissal and wished good luck. I tried entering the APN now with the correct MIN but again it deletes itself when I click Save.
I am going to try flashing stock since I need a phone. If anyone can confirm or deny the APN settings from the linked post I'd really appreciate it. And if there's some secret to clicking Save, I'd love to know that too!
Also, maybe it's because it's searching for a signal but the drain on the battery seems much higher than the stock ROM. It went down 25% in just an hour or so of trying to resolve this issue.
# Update:
It could be that the network type is incorrect. When I connect to adb, the prompt says "[email protected]_cdma:/ # ". But the service I use is LTE.
pushing APN via ADB
If someone adventurous is interested in pursuing this, it may be possible to shoehorn the APN settings in using ADB:
Steps:
http://android.stackexchange.com/questions/117125/how-do-i-add-an-apn-via-adb
Settings?:
http://teamuscellular.com/Forum/topic/5855-apn-settings/?p=99206
Please post back if you have success with this!
@loadcode Actually CM 12.1 wasn't tested on US Cellular XT1548, no one had this variant in those days. Try unofficial CM 13, if it works (I'm pretty sure it does) I'll port the fixes to CM 12.1 too
Thanks for the reply! I'm down for that! Where can I find the 13 download?
I did find this but the cellular still doesn't connect. It seems to try, and displays the SIM card icon next to US Cellular (only when I set the Preferred network type to 1g), but continues with the previously-mentioned symptoms.
Any other ideas? I didn't make a backup before jumping in. Does anyone have the original firmware that I could flash back on this device?
Alberto97 said:
@loadcode Actually CM 12.1 wasn't tested on US Cellular XT1548, no one had this variant in those days. Try unofficial CM 13, if it works (I'm pretty sure it does) I'll port the fixes to CM 12.1 too
Click to expand...
Click to collapse
@Alberto97 Is it possible for someone to edit the known issues page for the Osprey to make other US Cellular users aware of this? This would have saved me a more-stressful-than-necessary holiday.
I think I found the original firmware, so all might not be lost.
Thanks for your work on this!
loadcode said:
@Alberto97 Is it possible for someone to edit the known issues page for the Osprey to make other US Cellular users aware of this? This would have saved me a more-stressful-than-necessary holiday.
I think I found the original firmware, so all might not be lost.
Thanks for your work on this!
Click to expand...
Click to collapse
I have the virgin mobile variant.
It is also the same model as you. XT1548.
I along with others struggled to get custom ROMs to connect. But thanks to Alberto, it is now working
Try this
Flash Alberto's cm13 12-24 build from the site you linked above.
Once it boots, go to settings and click cellular networks.
Then click CDMA subscription.
If NV is selected, that is probably your problem.
Change to RUIM and reboot.
You may still need to add your APN settings, but maybe not.
Try it out. You just need to try a few things, I'm sure you will be up and running soon.
hossman said:
Try it out. You just need to try a few things, I'm sure you will be up and running soon.
Click to expand...
Click to collapse
@hossman, thank you very much for the encouragement and the suggestions. I'd love to have your confidence with this but I've tried many different combinations of the APN, Service Provider & Preferred Network Type and nothing has been the magic US Cellular desires.
Like Alberto said, apparently no devs tested it on the US Cellular network.
If it'll help I could try to provide testing results but I'm also really eager to have a phone again. Even if I could use my SIM card in my old phone for now that'd be acceptable, but for some reason it doesn't work in the 2014 version. (worked fine in my 3rd gen until flashing Cyanogenmod, so I don't think the SIM is bad.)
If it helps with development, here's a log of the network join attempt:
http://pastebin.com/jP8Xhisn
What rom is your phone currently? Did you restore stock firmware yet?
---------- Post added at 02:10 PM ---------- Previous post was at 02:09 PM ----------
Goto dialer and dial
*#*#4636#*#*
Click phone information
Is your phone # correct?
---------- Post added at 02:15 PM ---------- Previous post was at 02:10 PM ----------
The funny thing is I have had my carrier come up us cellular many times while trying to establish virgin mobile status
Sorry I did return it to stock. A (possibly relevant?) observation is that with the stock firmware, I have the option to toggle the CDMA roaming mode between home & auto. With the non-stock ROMs this was not listed.
For my reference if I attempt this again, and anyone else on US Cellular, here's the working APN settings from the device after I reverted to the original working firmware. All categories are 'Not set' unless otherwise listed here (even username & password):
APN Name (I assume this could be anything...): U.S Cellular
APN: usccinternet
MMSC: http://mmsc1.uscc.net/mmsc/MMS
MCC: 311
MNC: 580
APN type: default,mms,dun,hipri,fota
APN protocol: IPv4/IPv6
APN roaming protocol: IPv4/IPv6
APN enable/disable: APN enabled
Bearer: LTE
MVNO type: None
Don't get discouraged.
If you want to try again, feel free to pm me and I can try to help...no promises but I'll try..
We're online with the 2/6 build of Marshmallow! I did have to manually launch the Cellular settings app and manually enable/click on "LTE" and it came online immediately! WOOT!
Related
[RESOLVED] I just flashed the latest Clean ROM 6 R2 on my Rogers HTC One X and my Mobile Data is Disconnected even though it says 4G in the status bar with full reception. I also receive calls just fine.
I could not attach my screenshot but you can see the screenshot from this link
I wanna try turning off LTE and keep the connection on 3G only, but can't find the option to do that either
Screenshot
Anyone else having this problem? Any insight on this issue would be nice as I love this ROM!
Hey! I just un-soft-bricked my phone only to run into this problem too! BUT I have fixed it! Seemed the APN was wiped for me and is probably the same for you. I added the following APN and boom, all fixed! LTE, 3G, w/e you want! This had all the settings here Hope this gets things running for you too!
sixalive said:
Hey! I just un-soft-bricked my phone only to run into this problem too! BUT I have fixed it! Seemed the APN was wiped for me and is probably the same for you. I added the following APN and boom, all fixed! LTE, 3G, w/e you want! This had all the settings here Hope this gets things running for you too!
Click to expand...
Click to collapse
THANK YOU SO MUCH!! I waited all day to see an MMS! Totally made my day!
Just a heads up, that fix I posted was buggy for me as that doesn't actually include the proper Rogers LTE settings so I had random disconnects during today. Hopefully you're not, but if you notice your connection to be spotty pm me and I can send you my updated apn setting for rogers LTE network.
Just a heads up, I am also having this issue and it seems to be with any AT&T based rom. I have a telus one x. Added Telus APN and flashing different radio did not fix my problem. I tried both clean rom V6 R2 and an AT&T stock rom. I have flashed viper without issues and Original Android roms work fine. I notice a few people having this issue and some seem to be able to resolve by adding APN while others cannot resolve the issue. I'm at work right now so I can't do much testing but I will when I get home this evening. If anyone else has anything to add or perhaps if someone knows how to fix the issue, you're two cents is welcome!
Thanks!
*Edit* It seems as though my issue was being caused due to TWRP 2.4 not wiping properly so I went back to 2.3.3 and did a clean wipe/flash and all works fine after entering APN settings.
COMPLETE FIX FOR THIS PROBLEM (worked for me):
sixalive said:
Name: Rogers LTE
APN: ltemobile.apn
MMSC: http//mms.gprs.rogers.com
MMS proxy: 10.128.1.69
MMS port: 80
MMS protocol: WAP 2.0
MCC: 302
MNC: 720
APN type: *
Bearer: Unspecified
Click to expand...
Click to collapse
After setting the above APN settings, your data should work. But in my case, I kept loosing signal frequently at random. The following step fixed that for me:
1. Dial *#*#4636#*#*
2. Select Phone Information
3. Under Set preferred network type: Select GSM auto (PRL)
Now my reception will go as low as one bar but it will never cut
Hope this helps!
HTC One X data disconnected problem
sixalive said:
Just a heads up, that fix I posted was buggy for me as that doesn't actually include the proper Rogers LTE settings so I had random disconnects during today. Hopefully you're not, but if you notice your connection to be spotty pm me and I can send you my updated apn setting for rogers LTE network.
Click to expand...
Click to collapse
I have reset my phone and updated the APN setting given above but still the persists. Please help
I noticed that under Network settings for Global or GSM, the New APN feature to manually add an APN for different sim is gone. Looks like it's an auto detect feature now. I travel overseas for business alot and use pre-paid SIM cards. Not all prepaid sim cards have the data APN coded. I just found out on my trip here to Taiwan and couldn't get data on my phone because the option for adding the APN is no longer available. I tried multiple settings, different ROM's and no good. Only when I downgraded my firmware did the option come back. Glad I'm rooted, it sux, but had to downgrade and reflash back to the old 4.4.2 firmware/rUU and run custom ROM. Until this is addressed by verizon, there will be no way to manually add an APN.
rudyo78427 said:
I noticed that under Network settings for Global or GSM, the New APN feature to manually add an APN for different sim is gone. Looks like it's an auto detect feature now. I travel overseas for business alot and use pre-paid SIM cards. Not all prepaid sim cards have the data APN coded. I just found out on my trip here to Taiwan and couldn't get data on my phone because the option for adding the APN is no longer available. I tried multiple settings, different ROM's and no good. Only when I downgraded my firmware did the option come back. Glad I'm rooted, it sux, but had to downgrade and reflash back to the old 4.4.2 firmware/rUU and run custom ROM. Until this is addressed by verizon, there will be no way to manually add an APN.
Click to expand...
Click to collapse
Adding Screen shots for reference from my testing on my device Using 4.4.2 firmware and SkyFall Rom 2.7 and 4.4.3 firmware running both SkyFall 3.2 and RKDN rom 1.4 & final version tested.
Update: Figured the APN issue thing out
Thanks to member DOTTAT for giving me the direction I needed to get the APN assignment issue resolved. I just needed to do things differently for getting the APN to load up. Basically had to to to the 'Network Preferences' section to add the network my SIM cards are registered on. This is a long list to scroll through. After I selected the network, there is multiple options to add the network type (GSM,UMTS,LTE, etc.) Had to enable three different versions then reboot the phone. After, there were two APN's that automatically populated and I was able to edit. Thanks again to DOTTAT for the direction. :laugh::good:
rudyo78427 said:
Thanks to member DOTTAT for giving me the direction I needed to get the APN assignment issue resolved. I just needed to do things differently for getting the APN to load up. Basically had to to to the 'Network Preferences' section to add the network my SIM cards are registered on. This is a long list to scroll through. After I selected the network, there is multiple options to add the network type (GSM,UMTS,LTE, etc.) Had to enable three different versions then reboot the phone. After, there were two APN's that automatically populated and I was able to edit. Thanks again to DOTTAT for the direction. :laugh::good:
Click to expand...
Click to collapse
Sounds good man... Glad this will be useful for all. Might even take some guess work out of some of the weirder apns.
dottat said:
Sounds good man... Glad this will be useful for all. Might even take some guess work out of some of the weirder apns.
Click to expand...
Click to collapse
I apologize but I did not see the steps to get the apn settings access. I've got the HTC One M7 for Verizon on 4.4.3 and can not change apn settings. What would the steps be? Thank you so much for any and all help.
thewhiz7 said:
I apologize but I did not see the steps to get the apn settings access. I've got the HTC One M7 for Verizon on 4.4.3 and can not change apn settings. What would the steps be? Thank you so much for any and all help.
Click to expand...
Click to collapse
The info is in the last couple posts.
dottat said:
The info is in the last couple posts.
Click to expand...
Click to collapse
I figured I'd bump this thread rather than start a new one... It seems I and many other Verizon M8 users have encountered the same problem:
I get no list of network APNs under "Network Preferences." There are zero entries, even though a message pops up to say the list is full.
I tried manually entering the MCC/MNC numbers for my carrier abroad (Claro Brazil) but this doesn't resolve the problem. I am stuck with only voice but no mobile data service.
Has anyone found a solution to this? Verizon tech support of course insists "just pop in the SIM and it should work automatically" as does the Brazilian carrier.
Does anybody know where in the phone the APN settings are stored, to edit them manually?
!!!!!!Please do it on your own Risk..I would not held responsible for any damage for any cause to your phone..
Manged to get GSM signal outside US for LS996 Sprint version zv5, still trying for APN settings and Sprint carrier title change
This is what i did..
1) Rooted as per instructions available on internet or under Lg Flex 2 general thread..or site of highonandroid.. search for how to root lg g3, flex, flex2 etc..
2) After rooting installed root browser.apk via playstore or any equivalent market place
3) Opn Root browser which will prompt for supersu rights , allow / grant access permission
4) go to carrier folder and then go to apps folder.
5) Renamed two files which is under carrier/apps as *.bak
4) Added new files used the same files which is used for LG g3 sprint unlock..under carrier/apps (Attached )
5) Insert a SIM card before restarting.
6) Restarted the phone and got the signal bar with calling and SMS working..
Still awaited for APN settings and the GSM carrier still shows as Sprint where i need help
Update : Manage to get APN settings too.:
Install Shortcut master lite click and hold the recent apps button and click "Search"
Search for apn select com.andoird.settings$ApnSettingsActivity and then click Launch / homescreen
Select on the Top Right new apn
Fill this form out with the apn from your provider (If you don't know the apn look it up in google).
GSM carrier still shows as Sprint where i need help..
updates : GSM carrier shows proper names ..it seems had issue with my sim card..
now all working fine with GSM calling, sms, mms, , apn ..too
only thing needs to change the icon where its shows GSM while connected to data ..which can be changed to H / H+ ..which is mentioned in some other threads too..
Thnks, Bro, its working fine.
Could you guys provide a much easier or in depth instructions when editing the files I'm sort of new to it. Also do you know if it will change if you reboot. Also do you know if it will work on tmobile and lte on it thanks again for the help.
---------- Post added at 03:38 PM ---------- Previous post was at 02:38 PM ----------
alexander1297 said:
Could you guys provide a much easier or in depth instructions when editing the files I'm sort of new to it. Also do you know if it will change if you reboot. Also do you know if it will work on tmobile and lte on it thanks again for the help.
Click to expand...
Click to collapse
Could you guys provide a much easier or in depth instructions when editing the files I'm sort of new to it. Also do you know if it will change if you reboot. Also do you know if it will work on tmobile and lte on it thanks again for the help.
updated few notes as in for more clarity..Hope it would be now easy...
Ideally it should work with t-mobile or any gsm carrier unless it has a bad esn or restircted in US. It just disables the lock of sprint in an OS level.
thank you so much will try
do you get full LTE?
now i am going to buy this phone!
Thank you, you gave me a hope
LTE depends on the frequency available in your country but mostly you would not get it would be H+..which is equivalent to 3G..3G+
One of the thread has some updates on enabling the LTE bands..
http://forum.xda-developers.com/g-flex2/general/how-to-enable-lte-bands-band-4-1700-t3097409
HELP I RENAMED THE TWO FILES TO .bak THEN MOVED THE LG G3 ONES IN THAT SAME FOLDER THEN I REBOOTED AND NOTHING HAPPENED DID I DO SOMETHING WRONG
alexander1297 said:
HELP I RENAMED THE TWO FILES TO .bak THEN MOVED THE LG G3 ONES IN THAT SAME FOLDER THEN I REBOOTED AND NOTHING HAPPENED DID I DO SOMETHING WRONG
Click to expand...
Click to collapse
same with me can't unlock with these two files
After rebooting go to settings...more...mobile networks ..u should see options for GSM only, CDMA, WCDMA only WCDMA / LTE..select GSM only ...make sure once the file is replaced you insert a SIM card before rebooting. By default it selects the Global network options once rebooted. Hope it works for you both.
If needed i can add screenshots which i was able to achieve for gsm signal and the data signal (GSM icon).
i doubt or dont know whether it would work within US
sojanjoy said:
After rebooting go to settings...more...mobile networks ..u should see options for GSM only, CDMA, WCDMA only WCDMA / LTE..select GSM only ...make sure once the file is replaced you insert a SIM card before rebooting. By default it selects the Global network options once rebooted. Hope it works for you both.
If needed i can add screenshots which i was able to achieve for gsm signal and the data signal (GSM icon).
i doubt or dont know whether it would work within US
Click to expand...
Click to collapse
when i replace files and reboot it doesn't change anything my phone wasn't actived
which country / carrier are you trying..
I'm trying for tmobile in the U. S
---------- Post added at 03:19 PM ---------- Previous post was at 02:52 PM ----------
I'm guessing I'm missing something because now all it says is no service and it took in the sim. Can someone elaborate and what I'm missing plz it would be really helpful.
alexander1297 said:
I'm trying for tmobile in the U. S
---------- Post added at 03:19 PM ---------- Previous post was at 02:52 PM ----------
I'm guessing I'm missing something because now all it says is no service and it took in the sim. Can someone elaborate and what I'm missing plz it would be really helpful.
Click to expand...
Click to collapse
is the imei clean >>>?????
ill try one here for the USA tomorrow
and ill let u know
tonasoledad1 said:
is the imei clean >>>?????
ill try one here for the USA tomorrow
and ill let u know
Click to expand...
Click to collapse
Yeah its clean and plz if you could hopefully it works
Sprint Phone Activation
hey guys, id like to use this method to unlock but I have a great prolem with this. I dont live in the US an bought the phone there after I read that it can be unlocked. It came completely new to me. It was never activated with Sprint and I dont have any Sprint account or whatever. In Germany we only have GSM based networks. The 'self service' app always prompts me to activate the device but that isnt possible because of the GSM network or roaming or whaterver - even the sim that came with the phone didnt work. Is there any way to bypass this bull**** and get that phone working? Hope you guys can help me out with a good idea. Thany you
Best regards from Germany
Jan-M.91
P.S. if anyone finds a way to get 800, 1800 and 2600 MHz LTE bands working please let me know, just found a guide to get the 1700 MHz band.
Hey guys, little update here.
I managed to unlock using the files AND editig the build.prop from SPR to VZW, works so far. APN and MMS are fine. Big problem is GPS when I activate location settings the phone crashes and goes into bootloop. Only way out is reflashing with LGFlashTool. I tried two times so i fugured out that GPS causes the bootloop, SystemUI also closes during usage, all in all very buggy. I think of flashing another ROM, H959 (unlocked US version) or H955 (unlocked EU version) to get rid of the lock, the Sprint boatware and the 'hands free avtivation' that I cant do because I am in Germany with a GSM carrier. Anyone tried this so far? Hope you can help me out. As mentioned it is possible, I made two calls after the progress I described, but I dont recomend it because of bugs and other issues.
best regards
alexander1297 said:
Yeah its clean and plz if you could hopefully it works
Click to expand...
Click to collapse
sorry man i get the same error as u
no service
but ill keep trying
any inf about this model
domestic unlock
For me another version of files from G3 works perfect
For those that already flash H810PR but wanted to get LTE access like stock..
Dial 277634#*# in dialer
Open the menu
Go into Field Test > Modem Settings>LTE band Selection>Band 17
Back
Then go to RAT selection
Select GSM/WCDMA/LTE
You can check the status by
about phone>network>Mobile network type...
It will shows you LTE..
cheers
Updates:::: luckily we now have LTE auto choices within our preferred network selection..
Thanks to legendaryturtle
http://forum.xda-developers.com/showpost.php?p=62429251&postcount=13
faizalotai said:
For those that already flash H810PR but wanted to get LTE access like stock..
Click to expand...
Click to collapse
Any other setting that needed to be changed? I was going to write up a list to post, but maybe this is all we need.
informpage said:
Any other setting that needed to be changed? I was going to write up a list to post, but maybe this is all we need.
Click to expand...
Click to collapse
I think, that's all what we need to enable lte from our device using 810pr FW..
What i noticed is when we're calling, the connection will drop from 4g to 3g..I guess its the same as Verizon Variant
Dennisg34 said:
With the fact Verizon purposely drops your coverage from 3/4G to 1x while making a phone call? I've seen in the General G4 forum the "fix" for this is to setup advanced calling (which costs money). Anyone know if there's another fix? Possibly something to edit in build.prop (very highly doubt that)? Perhaps I'll have to wait for custom ROMs to come out in the future and have them enable this along with the Mobile Hotspot.
Click to expand...
Click to collapse
Wow, it works! Thank so much!
Unfortunately this isn't working for me . I'll keep trying after some updates finish up.
EDIT:
To clarify, my connection works but it shows 3G. This might be due to my poor signal at home. I'll check it again tomorrow where I know I usually get 4G.
This works, but we do drop to 3G when making calls.
I was wrong, these changes didn't make any noticeable difference (terrible LTE in my area).
I tried changing target_country to US and target_operator to ATT in BuildProp, but that killed 4G completely.
I posted ATT and H810PRa build.prop files here.
What does the LTE icon look like? I'm getting a 4G logo
That is LTE, you'll see "H+" for the fake 4g
Sent from my LG-H810 using Tapatalk
I'm getting really crappy 3G connection if anything. What are you guys using for APN? Maybe that's my problem?
---------- Post added at 03:06 PM ---------- Previous post was at 02:13 PM ----------
I tried using the default APN and the phone has all sorts of issues trying to connect to anything. I have to put the APN in manually to get anything.
What are you guys using for ATT APN?
---------- Post added at 04:06 PM ---------- Previous post was at 03:06 PM ----------
I did a combination of changes on top of the settings suggested here and got 4G finally. I did the settings the OP suggested and the following:
Defined a new APN based on info from here:
http://forums.androidcentral.com/go...-t-lte-apns-network-settings.html#post3301622
I also went back into the modem settings, LTE-A Carrier settings and hit the top option "CA Enable /SupportedBandCom" which also says All-enable under it. This resets things and boom, 4G.
Hopefully this helps anyone else that's having issues. Although I managed to back to HSPA trying to get the settings for you guys, doh.
@sorozco Here's the APN from my ATT version:
Name ATT Nextgenphone
APN nxtgenphone
Proxy Not set
Port Not set
Username Not set
Password Not set
MMSC http://mmsc.mobile.att.net
MMS Proxy proxy.mobile.att.net
MMS port 80
MCC 310
MNC 410
Auth type None
APN type default,mms,supl,hipri,fota
APN prot IPv4/IPv6
APN roaming IPv4/IPv6
However, here's a thread that suggest we should use a different APN.
One more step for settings to work
Actually did not work for me there is no where to select Lte in network mode. just gsm and wcdma. followed the instruction and it did say success. But no 4g lte.
Worked for me, thanks for posting. Now we just need the ATT official files.
Sent from my LG-H810 using Tapatalk
View attachment 3446193Hello all, after doing this I had LTE from activating it in RAT selection in the hidden menu.
In mobile network > Network Mode, it was still GSM/WCDMA auto and was driving me insane. I looked around and found out the LteConfigs.apk for the International versions did not have the AT&T MCC MNC added in, not letting us select GSM/WCDMA/LTE auto.
I took the app, decompiled, added it in lteready.xml and recompiled, now I can select it and it automatically selects it when reboot.
enjoy.
Put in system/app/LteConfigs/. Folder permissions 0755. LteConfigs.apk permissions 0644.
Remove the old apk and .odex
Take this apk and just replace with original. Set permissions to 0644. Reboot.
Can leave arm64 folder.
I took an edited lteready.xml file and replaced with the original one, no decompiling, just swapped with 7z.
legendaryturtle said:
Hello all, after doing this I had LTE from activating it in RAT selection in the hidden menu.
In mobile network > Network Mode, it was still GSM/WCDMA auto and was driving me insane. I looked around and found out the LteConfigs.apk for the International versions did not have the AT&T MCC MNC added in, not letting us select GSM/WCDMA/LTE auto.
I took the app, decompiled, added it in lteready.xml and recompiled, now I can select it and it automatically selects it when reboot.
enjoy.
Put in system/app/LteConfigs/. Folder permissions 0755. LteConfigs.apk permissions 0644.
Remove the old apk and .odex
Click to expand...
Click to collapse
Thanks bud, will updates the OP :good:
Has anyone been able to get Xposed installed? it looks like it installs, does the black screen for 15min, but when it reboots, xposed still isn't installed.
bobloadmire said:
Has anyone been able to get Xposed installed? it looks like it installs, does the black screen for 15min, but when it reboots, xposed still isn't installed.
Click to expand...
Click to collapse
Did you set to permissive..install se linux changer>set to permissive>reboot than try again with xposed
faizalotai said:
Did you set to permissive..install se linux changer>set to permissive>reboot than try again with xposed
Click to expand...
Click to collapse
didn't work.
legendaryturtle said:
Hello all, after doing this I had LTE from activating it in RAT selection in the hidden menu.
In mobile network > Network Mode, it was still GSM/WCDMA auto and was driving me insane. I looked around and found out the LteConfigs.apk for the International versions did not have the AT&T MCC MNC added in, not letting us select GSM/WCDMA/LTE auto.
I took the app, decompiled, added it in lteready.xml and recompiled, now I can select it and it automatically selects it when reboot.
enjoy.
Put in system/app/LteConfigs/. Folder permissions 0755. LteConfigs.apk permissions 0644.
Remove the old apk and .odex
Click to expand...
Click to collapse
Followed instructions, made sure to set permissions correctly, still don't have the option for GSM/WCDMA/LTE auto.
Edit: redownloaded apk, reinstalled, reboot. Now get lteconfigs has stopped error.
What else can I do?
mr.wizard said:
Followed instructions, made sure to set permissions correctly, still don't have the option for GSM/WCDMA/LTE auto.
Edit: redownloaded apk, reinstalled, reboot. Now get lteconfigs has stopped error.
What else can I do?
Click to expand...
Click to collapse
This is how I have mine setup. If that doesn't work, or same, send me your framework-res.apk and lteconfigs apk
Sent from my LG-H810 using XDA Free mobile app
Thanks for the update! It's working for me now on H810PR 04.
hi. first let me state, ive had no training in developing, im teaching myself bits and pieces here and there (through trial and error). now onto my issue:
I have a moto g 2015 osprey, us cellular, 8g version. ive got twrp recovery installed, and have tried two different custom roms, resurrection remix 5.5.7, and CM 12.1 latest nightly, both with stock kernel and with squid 2 kernel. the problem i am having is, with both roms, i have wifi, and can activate my phone on us cellular towers, but i have no data connection. (btw, i got both roms from android development thread, if that matters). hopefully someone is able to help me get my phone working on custom roms with the info i have provided, as i absolutely abhore stock roms. if not, ill gladly provide any info requested. and thanks in advance!
Those roms may have been wiping out your APN settings under Settings>More>Cellular networks>Access Point Names.
I don't have them in front of me but Google US Cellular APN and you should find them. Be sure and save the settings at the top before you back out. There are apps for APN settings but I haven't had much luck with any of them. There is one app though that I believe does give you the APN settings even if it won't change them. Search in Play for APN and you'll find lots of apps.
Tel864 said:
Those roms may have been wiping out your APN settings under Settings>More>Cellular networks>Access Point Names.
I don't have them in front of me but Google US Cellular APN and you should find them. Be sure and save the settings at the top before you back out. There are apps for APN settings but I haven't had much luck with any of them. There is one app though that I believe does give you the APN settings even if it won't change them. Search in Play for APN and you'll find lots of apps.
Click to expand...
Click to collapse
pardon, i forgot to mention that. CM 12.1 WAS deleting my apn, reloaded stock, took screenshots of my apn settings, loaded CM 12.1 and set them up manually. still no data connection. Resurrection did not delete my apn, but it added 2 others. selected the apn my carrier assigned when i got the phone, still no data connection.
I can't even register it on the towers. Just reports "Cellular network not available"