My device is the little known 'Symphony Xplorer P6'. Android L 5.0. It was rooted. And recently I flashed TWRP recovery using Mobileuncle. d-h.st/oEO9 this is the link to the .img file of the TWRP I used.
Later I installed Xposed installer and it tried to install Xposed framework but it didn't support my device. The install/update button was greyed out. So I went on XDA and found this alpha version of Xposed installer that works with Android L from here http://forum.xda-developers.com/showthread.php?t=3034811
Then I downloaded "xposed-v78-sdk21-arm.zip" from the same thread and flashed it using TWRP. And rebooted. It rebooted straight to recovery. I needed to check if the newly flashed zip file worked and I could finally install Xposed Framework but it won't reboot to system. So I decided to clear cache. I selected just the cache partition and swiped to wipe. But it was stuck showing "wiping cache". It was wiping cache for a long time but normally just wiping cache doesn't take that much time. So I pulled the battery and rebooted to recovery. Then I wiped Dalvik cache. Still didn't boot to system. But the cache was clear. So I tried a factory reset (the first option that shows in TWRP on the wipe menu) after I pulled my sim cards and external SD.
And now whenever I turn on my phone it shows the boot logo (Symphony logo, my phone's brand) and then goes to TWRP splash screen and the display blinks after a few seconds and again its the TWRP splash screen. Means when it was supposed to show recovery options (Install, wipe, backup etc) the splash screen started again. And blinks again and splash screen again and so on untill I pull the battery. I know my phone is not bricked because it turned on (or is it?). As it is stuck at the TWRP splash Screen, It cant go into recovery mode where you have Install, Wipe, Backup etc. options.
What do I do now? Experts, please help the noob
gr8Scottt said:
My device is the little known 'Symphony Xplorer P6'. Android L 5.0. It was rooted. And recently I flashed TWRP recovery using Mobileuncle. d-h.st/oEO9 this is the link to the .img file of the TWRP I used.
Later I installed Xposed installer and it tried to install Xposed framework but it didn't support my device. The install/update button was greyed out. So I went on XDA and found this alpha version of Xposed installer that works with Android L from here http://forum.xda-developers.com/showthread.php?t=3034811
Then I downloaded "xposed-v78-sdk21-arm.zip" from the same thread and flashed it using TWRP. And rebooted. It rebooted straight to recovery. I needed to check if the newly flashed zip file worked and I could finally install Xposed Framework but it won't reboot to system. So I decided to clear cache. I selected just the cache partition and swiped to wipe. But it was stuck showing "wiping cache". It was wiping cache for a long time but normally just wiping cache doesn't take that much time. So I pulled the battery and rebooted to recovery. Then I wiped Dalvik cache. Still didn't boot to system. But the cache was clear. So I tried a factory reset (the first option that shows in TWRP on the wipe menu) after I pulled my sim cards and external SD.
And now whenever I turn on my phone it shows the boot logo (Symphony logo, my phone's brand) and then goes to TWRP splash screen and the display blinks after a few seconds and again its the TWRP splash screen. Means when it was supposed to show recovery options (Install, wipe, backup etc) the splash screen started again. And blinks again and splash screen again and so on untill I pull the battery. I know my phone is not bricked because it turned on (or is it?). As it is stuck at the TWRP splash Screen, It cant go into recovery mode where you have Install, Wipe, Backup etc. options.
What do I do now? Experts, please help the noob
Click to expand...
Click to collapse
=
=
what version of android was it running?
=
=
=
keifus.rahn said:
=
=
what version of android was it running?
=
=
=
Click to expand...
Click to collapse
Android Lollipop 5.0 stock ROM
Symphony Xplorer P6 Factory Rom
Try Flashing the original firmware to see if that helps you, Most likely have to start back from square one. Please post results
How To Flash Stock Rom http://androidmtk.com/flash-stock-rom-using-smart-phone-flash-tool
Factory Rom Download link= https://docs.google.com/uc?export=download&confirm=rkEP&id=0B5cmBf2wWSUmLXhyWmlMWjh1Ulk
keifus.rahn said:
Try Flashing the original firmware to see if that helps you, Most likely have to start back from square one. Please post results
How To Flash Stock Rom http://androidmtk.com/flash-stock-rom-using-smart-phone-flash-tool
Factory Rom Download link= https://docs.google.com/uc?export=download&confirm=rkEP&id=0B5cmBf2wWSUmLXhyWmlMWjh1Ulk
Click to expand...
Click to collapse
I've downloaded and installed the USB drivers and Flash tool. Now downloading the stock ROM. As soon as download completes I'll begin flashing. Thanks for your links. Another thing, I've removed the battery and connected the phone via USB, the phone shows the charging screen for a moment then turns off, then again the charging screen and then turns off, Windows 7 is playing the device connected and disconnected sound as the screen happens. Is it normal?
Update: After clicking the download button in SP flash tool and connecting phone via USB the download procedure doesn't start. The device driver I installed was "Android Gadget VCOM driver (COM4)". I think I need the "MediaTek DA USB VCOM driver".. I'm going to install that.
Update 2: Installed "MediaTek Preloader USB VCOM driver" Download procedure started and running
gr8Scottt said:
I've downloaded and installed the USB drivers and Flash tool. Now downloading the stock ROM. As soon as download completes I'll begin flashing. Thanks for your links. Another thing, I've removed the battery and connected the phone via USB, the phone shows the charging screen for a moment then turns off, then again the charging screen and then turns off, Windows 7 is playing the device connected and disconnected sound as the screen happens. Is it normal?
Update: After clicking the download button in SP flash tool and connecting phone via USB the download procedure doesn't start. The device driver I installed was "Android Gadget VCOM driver (COM4)". I think I need the "MediaTek DA USB VCOM driver".. I'm going to install that.
Click to expand...
Click to collapse
Are you putting the battery back in before you plug in your device?
and can you still boot into recovery if so you can connect threw adb that way
keifus.rahn said:
Are you putting the battery back in before you plug in your device?
and can you still boot into recovery if so you can connect threw adb that way
Click to expand...
Click to collapse
The ROM downloaded even while the battery was plugged in. It worked. Phone's back at Factory mode and running. Thanks :good:
gr8Scottt said:
The ROM downloaded even while the battery was plugged in. It worked. Phone's back at Factory mode and running. Thanks :good:
Click to expand...
Click to collapse
Awesome i'm glad I could help you out and get you back going. :good:
Would you plz add [RESOLVED] on the title of this thread so it could help others that are going threw the same issue. :highfive:
Related
I rooted my MT4GS a few months ago but stuck with the stock ROM. I decided I wanted to try out the CyanogenMod 9.1 ICS ROM. I followed the following steps:
1) Installed ROM Manager.
2) ROM Manager indicated a newer version of ClockworkMod Recovery and I installed it (5.0.2.7).
3) Using ROM Manager, did a full backup of the current ROM. All went well.
4) Using ROM Manager, downloaded and installed CyanogenMod 9.1.0 stable-doubleshot. I specified to wipe the data and cache partitions. The installation seemed to go normally.
When the phone rebooted, it was stuck at the logo screen. Had to remove the battery to turn it off. Tried a couple times, still the same.
Since I had the backup, I decided I would use CWM to restore the old ROM.
When I boot into recovery mode, it shows CWM 5.0.2.7, but whatever option I try to choose from the recovery menu, The screen just goes blank with the CWM logo in the middle and nothing else happens. Hitting the power button returns me to the menu, but no option works, even power down or reboot. It just goes back to the CWM logo again and I have to remove the battery to shut it down.
So, I thought I would try using fastboot to flash the ROM again. When I boot the phone into the boot loader and select fastboot, then plug the phone in via USB, nothing happens. Windows does not see the phone and ADB or fastboot don't see it either. It's not a driver issue, as the computer is still setup from when the computer was rooted and I connect the phone all the time with no problems.
When the phone is off and plugged into USB or the charger, I still get the charging light, though it goes off after about 10 seconds, then comes back on and cycles like that.
Is there anything I can try at this point, or is my phone bricked? It seems like I followed all the steps correctly. Is there an update.zip I can put in the root folder and see if it picks it up?
Any help would be appreciated.
brucehvn said:
I rooted my MT4GS a few months ago but stuck with the stock ROM. I decided I wanted to try out the CyanogenMod 9.1 ICS ROM. I followed the following steps
...
Click to expand...
Click to collapse
Ok, after rebooting Windows, I was able to get the USB connection to the phone to work in fastboot. It seems I missed the step described in this thread:
http://forum.xda-developers.com/showthread.php?t=1508556
which states with S-ON you must flash the boot.img separately. I did that via fastboot and the phone boots into cyanogenmod now.
However, I still seem to have the issue with clockwordmod recovery. As long as I do the recovery functions from rom manager, everything is fine, but when I manually boot into the recovery menu, I get the same behavior of any choice from the menu just blanks the screen except for the CWM logo and nothing happens. I tried reflashing the recovery image using fastboot, but still no go.
brucehvn said:
However, I still seem to have the issue with clockwordmod recovery. As long as I do the recovery functions from rom manager, everything is fine, but when I manually boot into the recovery menu, I get the same behavior of any choice from the menu just blanks the screen except for the CWM logo and nothing happens. I tried reflashing the recovery image using fastboot, but still no go.
Click to expand...
Click to collapse
This is solved also. Seems on the MT4GS, the trackball is the selection button. The power button appears to only be a back button.
What a thread! Two nicely phrased problem definitions, two well explained solutions, and all from the same guy. Sorry we weren't able to help directly, but you obviously found the answers you needed elsewhere in the forum. And you updated the title as well to show it was solved. Thanks.
I've installed the CM12 ROM from this thread: http://forum.xda-developers.com/gal...nt/rom-cyanogenmod-12-lollipop-5-0-1-t2971945 and it was working fine, but I realized after installing that I had a lot of space on my internal storage still being used up by old apps I'd installed with the stock ROM. None of these apps were showing up in the app manager, so I decided to factory reset the device from the Settings menu in CM12 to wipe the internal storage and start over.
Now, my device gets to the TWRP "teamwin" splash page, and stays there, blinking to a black screen and back every few seconds. I can't get into recovery or system. I can get into download mode and I've flashed TWRP with Odin3 a few more times and it hasn't helped. My device is now stuck on this blinking flash screen and I cannot power it off. Holding the power button down simply reboots the device and I end up in the same spot. How can I fix this? I do have a backup of the stock ROM on a USB key that I made with TWRP before flashing the CM12 ROM, if that helps.
Thanks!
So after some digging, I found this: http://forum.xda-developers.com/showpost.php?p=59627179&postcount=544 and I'm currently downloading stock firmware from sammobile at an excruciatingly slow speed. I should be able to try flashing it in 6-7 hours(!), and hopefully that gets the device booting properly again, then I'll try flashing TWRP, CM12, and gapps again.
Hey guys!
So, i was trying to install CM13 unofficial version, and wiped the system and internal storage using TWRP recovery. I was supposed to install the rom from a zip file i had placed in the external memory card. What i did, was, i rebooted the phone by mistake, after wiping it from the recovery without installing the ROM and now the phone is caught in a bootloop. I know i am an idiot to do that. I tried removing the battery and reboot it in recovery mode using the key combination with no luck. It just starts the boot loop. I tried using fastboot and adb from pc to push files into the internal memory, but my device is not getting detected on the adb anymore (maybe the usb debugging is disabled now?).
What i guess is stopping TWRP recovery from showing up is the lack of twrp/themes folder in the internal memory since i wiped it. But there might be some other cause that i am unaware of. What do i do now? Any help will be greatly appreciated!
Hey! I'm having the same problem with my yu yureka.. Can anyone help me please!
Kaustubh M said:
Hey guys!
So, i was trying to install CM13 unofficial version, and wiped the system and internal storage using TWRP recovery. I was supposed to install the rom from a zip file i had placed in the external memory card. What i did, was, i rebooted the phone by mistake, after wiping it from the recovery without installing the ROM and now the phone is caught in a bootloop. I know i am an idiot to do that. I tried removing the battery and reboot it in recovery mode using the key combination with no luck. It just starts the boot loop. I tried using fastboot and adb from pc to push files into the internal memory, but my device is not getting detected on the adb anymore (maybe the usb debugging is disabled now?).
What i guess is stopping TWRP recovery from showing up is the lack of twrp/themes folder in the internal memory since i wiped it. But there might be some other cause that i am unaware of. What do i do now? Any help will be greatly appreciated!
Click to expand...
Click to collapse
Hi! I'm having the same problem with this post... Does anyone knows the solution of this problem. I'd be really glad if anyone could help me with this..please!
Hey are you able to boot into fastboot mode? If you can....
Prerequisites –
1. Make sure that you have 70-80% battery on your phone.
2. You need a PC and a USB cable to connect your phone to the PC.
3. Flashing the factory firmware will wipe all the data present in the internal memory. So, make a backup of that if you can.
4.Install all the necessary Device drivers.
DOWNLOADS -
1. Download the flash tools from here . http://www.mediafire.com/download/87gfz7mdch188an/Flashtools_For_Yu_Yureka.zip
2. Download the factory firmware from Here (cm 12.1) . http://builds.cyngn.com/factory/tomato/cm-12.1-YOG4PAS3JM-tomato-signed-fastboot.zip
Steps To Flash Factory Firmware –
1. Extract the flashtools zip in a new folder on the desktop.
2. Extract the factory firmware zip in the same folder and make sure that all of the flashtools files are also present.
3. Now, power off your phone. If you are stuck in a bootloop, then pull out the battery and reinsert it. (Do not switch on the phone.)
4. While pressing the Volume Up key, connect your phone to the PC with the help of a USB cable.
5. You should now see the fastboot logo on your device. If you did, leave the Volume Up key. (If you do not see the logo, retry the process.)
6. Now go to the folder where you extracted the flash tools and factory firmware and run the flash-all.bat by double clicking on it.
7. A command window will open and the flashing procedure will start. (Make sure that your device does not disconnect from your PC during the procedure.)
8. The command window will automatically close once the procedure is completed.
9. Disconnect your device and boot it up by pressing the Power button. (Since this is first boot after flashing the firmware, it may take upto 5 minutes.)
Done you should be back on cm 12.1
Credits – ArnavG (Yuplaygod Forums) and Cyanogen Team.
im also having same problem i have also unknowingly wiped system & now im not able to flash any rom while flashing its rebooting automatically & i am able to enter in to fastboot mode then i have flashed factory firmware then also its not booting stucked on boot loop.
arunbiju969 said:
Hey are you able to boot into fastboot mode? If you can....
Prerequisites –
1. Make sure that you have 70-80% battery on your phone.
2. You need a PC and a USB cable to connect your phone to the PC.
3. Flashing the factory firmware will wipe all the data present in the internal memory. So, make a backup of that if you can.
4.Install all the necessary Device drivers.
DOWNLOADS -
1. Download the flash tools from here . http://www.mediafire.com/download/87gfz7mdch188an/Flashtools_For_Yu_Yureka.zip
2. Download the factory firmware from Here (cm 12.1) . http://builds.cyngn.com/factory/tomato/cm-12.1-YOG4PAS3JM-tomato-signed-fastboot.zip
Steps To Flash Factory Firmware –
1. Extract the flashtools zip in a new folder on the desktop.
2. Extract the factory firmware zip in the same folder and make sure that all of the flashtools files are also present.
3. Now, power off your phone. If you are stuck in a bootloop, then pull out the battery and reinsert it. (Do not switch on the phone.)
4. While pressing the Volume Up key, connect your phone to the PC with the help of a USB cable.
5. You should now see the fastboot logo on your device. If you did, leave the Volume Up key. (If you do not see the logo, retry the process.)
6. Now go to the folder where you extracted the flash tools and factory firmware and run the flash-all.bat by double clicking on it.
7. A command window will open and the flashing procedure will start. (Make sure that your device does not disconnect from your PC during the procedure.)
8. The command window will automatically close once the procedure is completed.
9. Disconnect your device and boot it up by pressing the Power button. (Since this is first boot after flashing the firmware, it may take upto 5 minutes.)
Done you should be back on cm 12.1
Credits – ArnavG (Yuplaygod Forums) and Cyanogen Team.
Click to expand...
Click to collapse
Bro tried that but nothing........
rss3183 said:
Bro tried that but nothing........
Click to expand...
Click to collapse
Can you be more specific ? Are you facing boot loop too?
anybody please help... facing the same problem and tried the solution as mentioned above but still facing Boot loop. what to do friends. please reply
I suddenly faced bootloop.....then I tried to flash stock rom without root...as a web page suggested me that....it was flashed successfully ...but still I am facing bootloop issue .....can someone pls help me to get out of this mess....pls help me...ASAP !!!
arunbiju969 said:
Hey are you able to boot into fastboot mode? If you can....
Prerequisites –
1. Make sure that you have 70-80% battery on your phone.
Click to expand...
Click to collapse
as its in boot loop battery has come to an end.... now what? having same problem as the topic creator
If you can boot into fastboot try flashing the Twrp from a computer,if you need steps on how to flash Twrp Post here if the flash is successfull boot into recovery and flash A new rom and this should boot your device
arunbiju969 said:
If you can boot into fastboot try flashing the Twrp from a computer,if you need steps on how to flash Twrp Post here if the flash is successfull boot into recovery and flash A new rom and this should boot your device
Click to expand...
Click to collapse
I flashed the factory image via YGDP tool as well as fastboot. But it boots upto a point and then goes in bootloop. Also if i wipe data/cache still it makes no difference. Also unlocked bootloader and twrp also don't load up. Again goes in bootloop.
Yogesh1969 said:
I flashed the factory image via YGDP tool as well as fastboot. But it boots upto a p loopoint and then goes in bootloop. Also if i wipe data/cache still it makes no difference. Also unlocked bootloader and twrp also don't load up. Again goes in bootloop.
Click to expand...
Click to collapse
were you trying to flash the twrp for the first time?? Was your yureka plus on stock kitkat??
Sorry for a late reply...
arunbiju969 said:
were you trying to flash the twrp for the first time?? Was your yureka plus on stock kitkat??
Click to expand...
Click to collapse
The problem got solved bcos it had a battery problem !!!! Battery showed 90-100%, but could not hold up on boot.
A very strange case. Thanks.
Hi, I flashed my Yu Yureka AO5512 Yesterday and entered into recovery mode and selected the wipe userdata option. When it was doing the process after 20min the process stopped all together and My phone does not start at all now. If i press any button there is no response at all. Looks like phones OS and everything is wiped out. How do i go about from here?
Same problem , Stuck in BootLoop
arunbiju969 said:
were you trying to flash the twrp for the first time?? Was your yureka plus on stock kitkat??
Click to expand...
Click to collapse
Bro , my Yureka was on Stock Lollipop (5.1) and i flashed Twrp 2.8x.x on it and now it''s Stuck in bootloop , i can't turn of the phone nor it starts , what should i do , any help appreciated
Thanks
YuganshT7 said:
Bro , my Yureka was on Stock Lollipop (5.1) and i flashed Twrp 2.8x.x on it and now it''s Stuck in bootloop , i can't turn of the phone nor it starts , what should i do , any help appreciated
Thanks
Click to expand...
Click to collapse
Sorry to hear that anyway,
By stock lolipop you mean you had the yureka plus with Volte From factory right!!...if so the twrp might have been for the yureka plus with the cm bootloader which got replaced in the new Devcice
I am facing the same problem and in my case I dont think its an battery issue...I was happily using the CM 13.0 Snapshot Rom since a long time...but today morning when I did a soft reset by going into the settings in my yureka...the phone has gone in bootloop...and nothing is working...using fastboot I even flashed the twrp again and also flashed the CM 12.0 Stock firmware..but nothing is working...after the YU logo it restarts....please help...
I am also facing problem maybe worst
I dont know what wrong I am doing but I am getting "FAILED (remote: unknown command)".
Few info:
1. I get my device ID when I do "fastboot devices" but nothing on fastboot -i 0x1ebf oem device-info".
2. Also for my YU5510A fastboot screen doesnt say' "fastboot" it says "Information do not unplug the cable - Secure Phone".
3. I have red light on, phones keeps rebooting 4-5 times than red light goes off and charging stops.
Aditi Apte said:
I dont know what wrong I am doing but I am getting "FAILED (remote: unknown command)".
Few info:
1. I get my device ID when I do "fastboot devices" but nothing on fastboot -i 0x1ebf oem device-info".
2. Also for my YU5510A fastboot screen doesnt say' "fastboot" it says "Information do not unplug the cable - Secure Phone".
3. I have red light on, phones keeps rebooting 4-5 times than red light goes off and charging stops.
Click to expand...
Click to collapse
Ignore that and use other fastboot commands and go ahead, as your device is being detected in fastboot mode.
FAILED (remote: unknown command)
Yogesh1969 said:
Ignore that and use other fastboot commands and go ahead, as your device is being detected in fastboot mode.
Click to expand...
Click to collapse
But when I am executing other fastboot commands it halts the process between with error "FAILED (remote: unknown command)".
I have read about this error and people suggested that I need to get into "Download mode" not "fastboot/bootload". To get into "download" mode I tried pressing "VoulumeDown+Power+Home", but nothing happened, it simply restarted the phone.
Please advise.
-Aditi
Hello,
I had some issues in phone and had to wipe all the data in it (from recovery mode) with the thought of flashing the firmware after cleanup. The only way i know to flash this firmware is by SP flash tool and here's the issue!! the phone wont connect to the pc in switch off mode which is a need of the process. I've gone through a lot of forums on different websites including this (I asked for the issue on forum but didnt get any help), a lot of forums start from after the mt65xx preloader shows in the device manager.
The things i've tried are deleting the drivers of MTK device(The only thing available related to this phone) from my pc with the help of USB Deview , Tried pressing volume up button while connecting the phone(Without battery) to pc and even inserting the battery just after connection.
Any help would be grateful..Thanks!!
P.s- Unfortunately usb debugging is off in the phone
Sp5297 said:
Hello,
I had some issues in phone and had to wipe all the data in it (from recovery mode) with the thought of flashing the firmware after cleanup. The only way i know to flash this firmware is by SP flash tool and here's the issue!! the phone wont connect to the pc in switch off mode which is a need of the process. I've gone through a lot of forums on different websites including this (I asked for the issue on forum but didnt get any help), a lot of forums start from after the mt65xx preloader shows in the device manager.
The things i've tried are deleting the drivers of MTK device(The only thing available related to this phone) from my pc with the help of USB Deview , Tried pressing volume up button while connecting the phone(Without battery) to pc and even inserting the battery just after connection.
Any help would be grateful..Thanks!!
P.s- Unfortunately usb debugging is off in the phone
Click to expand...
Click to collapse
Hi, is your device completely dead? Or it boots?
If your device's is alive, get sprout4 Stock Rom and flash it via custom recovery like Philz or TWRP!
sachin n said:
Hi, is your device completely dead? Or it boots?
If your device's is alive, get sprout4 Stock Rom and flash it via custom recovery like Philz or TWRP!
Click to expand...
Click to collapse
Hello, thanks for the support
The phone boots and get into a bootloop, as i mentioned that i wiped the data out, and i can enter in recovery mode but not in fastboot (maybe coz usb debugging is off).
I had no idea about sprout4 and that android one devices have common ROM and recoveries !!!!
I have found my device listed on this page but how do i flash recovery in my phone? The way i know is through ADB and that wont work.
I would like to know if theres any other way to do it .
Thanks!!
Sp5297 said:
Hello, thanks for the support
The phone boots and get into a bootloop, as i mentioned that i wiped the data out, and i can enter in recovery mode but not in fastboot (maybe coz usb debugging is off).
I had no idea about sprout4 and that android one devices have common ROM and recoveries !!!!
I have found my device listed on this page but how do i flash recovery in my phone? The way i know is through ADB and that wont work.
I would like to know if theres any other way to do it .
Thanks!!
Click to expand...
Click to collapse
Oww, that's cool bruh.
Hang on, I'll link you a Sprout4 Full stock ROM [latest one]
All you need to do is, just enter into recovery mode then wipe everything except micro SD, flash the given Rom zip, give few minutes, once the Flashing done, reboot!
Edit - Rom Link - https://www.androidfilehost.com/?fid=24686681827315150
*.Note that, all the sprout4 roms compatible with each other, so just download the zip, put it to your SD, reboot recovery, wipe all [Wipe system, data. except SD card ], flash that zip, reboot!
No need for ADB stuffs.
sachin n said:
*.Note that, all the sprout4 roms compatible with each other, so just download the zip, put it to your SD, reboot recovery, wipe all [Wipe system, data. except SD card ], flash that zip, reboot!
Click to expand...
Click to collapse
urgh... Stock recovery doesnt show 'install from sd card'. The only options visible are apply update from sdcard , ..from adb, wipe data/factory reset, wipe cache.
thanks!
Sp5297 said:
urgh... Stock recovery doesnt show 'install from sd card'. The only options visible are apply update from sdcard , ..from adb, wipe data/factory reset, wipe cache.
thanks!
Click to expand...
Click to collapse
Lolwut? :/
You were on stock recovery!!!
Deym, I thought you were on Custom Recovery like Philz or TWRP!
So now, @Sp5297... Your device is just bootlooping? And before this had took place, you were on stock Rom right? What was the build number?
sachin n said:
Deym, I thought you were on Custom Recovery like Philz or TWRP!
Click to expand...
Click to collapse
Oops, i thought i asked for how to flash em!!
Well, whats next now!!
Sp5297 said:
Oops, i thought i asked for how to flash em!!
Well, whats next now!!
Click to expand...
Click to collapse
Err... I misread that, pardon me.
AFAIK, if you wipe data / factory reset from stock recovery, then that's not at all an issue, just reboot the device that's gonna work.
You can't i guess, fastboot / ADB modes requires theyve to enabled from settings /developer option. So it was looping / you can't do that either.
First tell me what build you were on before this took place.
Flashing the very next OTA[prior to that] via stock recovery will works sometimes.
@saichin n I have the same problem with my phone, I tried to use sp frashtool but as sp5297 the phone doesn't connect with the pc (it connects only when i do apply update from ADB). When i plug in the pc without battery it's just dead. My mobile is Karbonn Sparkle V
Edit: It started to bootloop me when i tried to start a game (soccer stars official). When i start it it just crashed the UI and i restarted it via power button
Hi bro. I have the same prob with my Karbonn Sparkle v (Not rooted) with 6.0.1/MOB31E
Hi bro. I have the same prob with my Karbonn Sparkle v (Not rooted) with 6.0.1/MOB31E . I am stuck at bootloop too and cant flash any roms as it errors that earlier version can not be flashed or so. I am not able to connect my fone to PC as well, its not detecting, Can I flash anything from SD Card ( as in recovery it gives option to update from Sd Card). I have tried factory reset, cache cleaning but nothing wokred. could you please advise me on this??? appologise, not sure where to write my query, as i just joined today.
Hello
Having some issues with my phone
I was using a custom rom beforehand and decided to flash the official stock rom because of a mobile app game that wouldn't boot on the phone. Doing that got rid of twrp and opened the stock recovery. Whenever I tried to reboot the phone it would keep taking me to the stock recovery. From there I decided to do a wipe but it continued to take me to the stock recovery. Not sure what to do I fast booted a .img file I used for the previous custom rom I was using and that booted the phone to a point where it had official stock and was rooted but the game still didn't work. So when I rebooted into recovery mode the twrp recovery appeared but when I checked my files everything was gone. Whenever I tried to reboot the phone it would just continue to take me into twrp recovery. Also I couldn't move files while it was in twrp. So I decided to format everything and that fixed my issue of booting. Now the phone booted as normal even tho I had to go through the intro again. I downloaded the game and huzzah it worked just fine. I booted into recovery mode to make sure it would boot fine from recovery to the phone and it did, but whenever I told twrp to reboot it would say there is no os installed but it would boot fine. Next I decided to get magisk back and running. So I got the manager and download the .zip and booted twrp and flashed it. When I rebooted my phone I just get a blank screen. Nothing happens when I press anything and pressing power + vol up restarts the phone but it goes back into a blank screen.
Help?
3ds1234 said:
Hello
Having some issues with my phone
I was using a custom rom beforehand and decided to flash the official stock rom because of a mobile app game that wouldn't boot on the phone. Doing that got rid of twrp and opened the stock recovery. Whenever I tried to reboot the phone it would keep taking me to the stock recovery. From there I decided to do a wipe but it continued to take me to the stock recovery. Not sure what to do I fast booted a .img file I used for the previous custom rom I was using and that booted the phone to a point where it had official stock and was rooted but the game still didn't work. So when I rebooted into recovery mode the twrp recovery appeared but when I checked my files everything was gone. Whenever I tried to reboot the phone it would just continue to take me into twrp recovery. Also I couldn't move files while it was in twrp. So I decided to format everything and that fixed my issue of booting. Now the phone booted as normal even tho I had to go through the intro again. I downloaded the game and huzzah it worked just fine. I booted into recovery mode to make sure it would boot fine from recovery to the phone and it did, but whenever I told twrp to reboot it would say there is no os installed but it would boot fine. Next I decided to get magisk back and running. So I got the manager and download the .zip and booted twrp and flashed it. When I rebooted my phone I just get a blank screen. Nothing happens when I press anything and pressing power + vol up restarts the phone but it goes back into a blank screen.
Help?
Click to expand...
Click to collapse
OK here is some quick help: https://piunikaweb.com/2019/05/29/how-to-unbrick-oneplus-7-pro-using-msm-download-tool/
I've tried this but it doesn't work. Whenever I boot the program nothing shows up. I checked my ports and I have Qualcomm HS-USB QDLoader 9008 (COM8) which doesn't match the guide and I have no idea how to change the port.
3ds1234 said:
I've tried this but it doesn't work. Whenever I boot the program nothing shows up. I checked my ports and I have Qualcomm HS-USB QDLoader 9008 (COM8) which doesn't match the guide and I have no idea how to change the port.
Click to expand...
Click to collapse
The COM number actually doesn't matter, it will vary from pc to pc so yes it will work, nothing will show up on the phone screen its self, once u see HS-USB QDLoader 9008 open the msm tool and u will see it connect and start.
What custom ROM?
What game?
Which TWRP?
Which boot.img?
What firmware?
What everything?
How on earth can you expect anyone to help you when you decide to cloak your whole setup in mystery?
I fixed the issue. I didn't know about the button combo to boot into fastboot so when I did boot into fastboot I fastbooted into twrp and fixed everything from there