Look at the cable on the microUSB back side, you'll see two pins popping out a little. Issue i had with that cable is while i tried to put the connector in the right position (it was bended) i pushed in the wrong side and those pins where not popping out anymore..
Which is a problem since they help phone to detect while you connect & disconnect cable, maybe more. I tried to make the pins pop out using a needle. Worked for some time, until days ago. While trying to fix, i realised that these pins will actually pop in/out depending on how you bend the connector.
So i bended it to make them pop out just as if brand new. Problem is now, even though the phone detects (and hold tight) the cable/AC power, the phone won't charge. Just like if no power was coming it. I tried various things, but it won't change. This cable is much longer/better than others, hope i can fix it..
..........
Always quote my messages so I get notified quickly!
Buy a new one?
Related
I had problem with phone believing it was connected to usb and showing as connected in top bar when cable was unplugged. Phone would show spinning battery icon and refuse to boot unless usb was connected but usb didn't work. The problem was corrosion in the usb port even though connector on phone looked clean. My solution was to buy cardboard emery board from drugstore. Cut down board to fit slot and shave board thickness on one side so it fits into the slot and tab comfortably. About twenty strokes later I had a phone that once again functioned properly and as a bonus data speed throughput over usb noticeably increased.
thanks for you post . my phone suddenly started to do this , so annoying
didnt have an emery board though , wife wouldnt part with one lol.
did use tip of a knife to carefully scrape connector .
after 3 weeks + of my phone not booting without charger ,i spent less than 30 seconds on this fix .
my phone booted first time
many thanks
Thanks a bunch! - You just saved my day.
I did the knife thingy, and fixed my Samsung i9100..;o)
Thanks again I tried blowing compressed air in mine and it didn't work, I was scared to use a knife just in case but if multiple people have then I will give it a blast...
THANKS!!!!
Just wondering if anyone else's usb cable is a little bit "shaky" after being plugged in? I guess it's normal since i don't have any poor contact issue so far, but ...it's kinda annoying..
Sorry if you didn't notice it before but you do now
ye my last android did that too. after using the micro usb port a few times it gets "shaky"-er haha
NIKEstickER said:
ye my last android did that too. after using the micro usb port a few times it gets "shaky"-er haha
Click to expand...
Click to collapse
ya all my phones with a micro usb port have eventually gotten this way...
futureaccount said:
Just wondering if anyone else's usb cable is a little bit "shaky" after being plugged in? I guess it's normal since i don't have any poor contact issue so far, but ...it's kinda annoying..
Sorry if you didn't notice it before but you do now
Click to expand...
Click to collapse
My Epic 4G Touch is the same exact way. However, I never had this issue with my Evo. Wonder if its an issue with the ports on Samsung phones.
I have found taking a pair of pliers and adding some slight pressure to the end of the usb cable has helped tighten things up. Make sure you are squeezing the entire connector and not using needle nose.
promiseofcake said:
I have found taking a pair of pliers and adding some slight pressure to the end of the usb cable has helped tighten things up. Make sure you are squeezing the entire connector and not using needle nose.
Click to expand...
Click to collapse
Its funny that you mention that because the looseness seems to be more dependent on the actual USB cable than the port itself (at least on this phone) Luckily, I haven't had any real connection problems with my phone. However, after replacing the cable, it seems to fit more snugly. Either way, its a little odd that it the same cable will seem more loose in this phone, but fit just fine in my previous one (still have it as a spare).
I've been having this problem lately also. Thinking in was a bug in the rom or a bad cable, the problem persists and its getting worse to the point it constantly will connect and disconnect repeatedly. I'm thinking its the phone because I've changed cables, usb ports and it still does it. But sometimes it will stick normally. Wierd...
If you have even tried brand new cables (since your existing ones may be worn out), then I would say that the port on the phone is likely damaged. Looks like it may be time for a service center repair.
My SR is the same way. The mini usb cocksoff to the right. I've experienced the same with a few Motos. I've came to the conclusion it is the cables themselves. I have noticed that the two teeth on the male plug get kind of wore out or not even pop back out and furthermore eventually damage the female port to where the phone will cycle from power to no power. I've especially seen this with OEM cables. I also saw a thread here where the guy gives an awesome, detailed breakdown of a screen replacement. The site he links has the replacement chip with the mini usb port if you feel froggy...
My HTC Sensation, has stopped charging altogether. I took it off charging and when i put it on 10 min later, the LED didnt light up, so i got a toothpick and tried cleaning thecharging port just in case something tiny went in and was blocking it to charge, but that didnt work. The phone was working fine until the battery died and i still cant get it to charge. Now im wondering whats broken, to all those repair specialists out there, what could be broken? I can buy a charging port from ebay, but is that it? or could it be anything else.
I was looking to upgrade soon but was waiting for some christmas deals to pop up, but my phone decided to let me down.
Any help appreciated, thanks guys
webstar1 said:
My HTC Sensation, has stopped charging altogether. I took it off charging and when i put it on 10 min later, the LED didnt light up, so i got a toothpick and tried cleaning thecharging port just in case something tiny went in and was blocking it to charge, but that didnt work. The phone was working fine until the battery died and i still cant get it to charge. Now im wondering whats broken, to all those repair specialists out there, what could be broken? I can buy a charging port from ebay, but is that it? or could it be anything else.
I was looking to upgrade soon but was waiting for some christmas deals to pop up, but my phone decided to let me down.
Any help appreciated, thanks guys
Click to expand...
Click to collapse
Did you solved the problem by buying a new phone?, the problem could be the USB connector himself, if you are very handy you can repair it yourself...
anomalic said:
Did you solved the problem by buying a new phone?, the problem could be the USB connector himself, if you are very handy you can repair it yourself...
Click to expand...
Click to collapse
maybe your battery died
I'm assuming you've got it fixed / moved on to a different phone / are using an external charger, but this thread got bumped to the top so I figured I'd chime in.
I had this problem as well. Unfortunately, the usb port is soldered on the board and not a separate unit attached via ribbon cable. The solder joint holding the port on the pcb cracked, resulting in a loose port. Over time, this lead to the pins breaking off the pcb. For a while, I was able to get it to charge by applying pressure to the usb plug. Finally, I took it apart and resoldered it, reinforcing the solder joints for the port itself. It's not too difficult if you use some flux. Just line up the pins and tack the port back on. Then rub flux over the pins and tack them with the soldering iron. No additional solder is needed or recommended-- the pins are in close proximity and it'd be easy to bridge them.
When looking into the USB port I noticed there is a slight build up of green gunk which probably came from environmental moisture (not sure).
Possibly related to this is that when connecting PC to phone, some USB cables won't work (and sometimes power surge), some only works in one orientation, some only works via the wall charger.
Before I send my phone in for repair, just wondering if anyone here has had a similar problem, and what you did to fix it. Any help and comments will be appreciated.
Hi, i had this corrosion too, what i did (maybe not so sure way) its cleaning the corrosion that was between the pins of the connector, so first i turned off the phone and then i removed it with a needle, be careful with the pins. When you finish use a brush to clean the port a little more and remove the dust it may have, you can put alcohol on the brush.
If your cables are not working you can try to press a bit both horizontal sides of the connector to ensure the pins are always touching. Thats what i did when my usb c cable started to connect and disconnect the phone randomly when i just moved it a little.
ClementNg23 said:
When looking into the USB port I noticed there is a slight build up of green gunk which probably came from environmental moisture (not sure).
Possibly related to this is that when connecting PC to phone, some USB cables won't work (and sometimes power surge), some only works in one orientation, some only works via the wall charger.
Before I send my phone in for repair, just wondering if anyone here has had a similar problem, and what you did to fix it. Any help and comments will be appreciated.
Click to expand...
Click to collapse
Hey. Welcome to the club mate. I screwed up my charging port after a trip in Thailand. Some underwater diving & swimming caused the green junk in my port.
I had the same issue such as yours after the trip, Charging was fine but connection through usb on a computer was screwed up.
What I did was, cleaned the charging port with alcohol (Nail polish remover), let it dry & sent it to a nearby Sony Service centre.
They replaced my mother board for free (In warranty). The best part was I had my bootloader unlocked & they gave me a new motherboard with a locked bootloader
Sony service center employees don't know **** about Bootloaders in my country, I'm from India btw.
Hi guys!
I'm a fresh Pixel 2 user (and for now, I love the device), but a very strange thing occurred to me. I unboxed the phone, connected the cables to transfer the data from my old Nexus, and everything went smoothly, the cable connected easily and firmly. When I came home and wanted to connect the charger I noticed I can't push the USB-C cable in - it was getting stuck before being pushed completely, and the phone wouldn't charge. I looked closely into the charging port thinking that maybe some small debris was locked inside, but instead I've seen a crooked metal brace (closeup photo attached, the part was really small) that seemed loose and was blocking the connector to go fully inside. I didn't know what it was, but I used a toothpick to try to lock it in place or at least see if it's really loose, but upon touching it simply came out from the port and hit the floor.
The port now works flawlessly, it charges, it connects to the computer, nothing seems lose, the cable sits tight, and it looks perfectly normal to me. I checked some other USB-C devices I have if they have similar metal thing inside, but none does. The port now looks like all other USB-C ports I've seen.
I wouldn't expect anything to come out of the charging port in a new phone though. Would you have any idea what's the purpose of this metal brace in the Pixel's port, and what could've happened that it got detached from the port? Should I be worried or just throw it into the bin and forget?
I'd appreciate any clues and insights
Thanks!
M.
This looks like half of the metal usb shield inside your port. If you look deep inside there should be another half (or maybe it's fallen out). The purpose of this part is purely to reduce electrical noise at the point of the connector, so you shouldn't really see any charging issues with it out, although you may run into the occasional data transfer issue.
Thanks, that's reassuring I don't really see the second half, but everything is working smoothly so I will not be too bothered then.
Keep the part. The phone is faulty. If you don't have problems, wait until the warranty is nearly out and then RMA the phone to get a 'new' one
This exact thing just happened to my Pixel 2 phone. I hope I don't have any problems. I know this is an old post. Did it ever cause you any problems?
maticomp said:
Hi guys!
I'm a fresh Pixel 2 user (and for now, I love the device), but a very strange thing occurred to me. I unboxed the phone, connected the cables to transfer the data from my old Nexus, and everything went smoothly, the cable connected easily and firmly. When I came home and wanted to connect the charger I noticed I can't push the USB-C cable in - it was getting stuck before being pushed completely, and the phone wouldn't charge. I looked closely into the charging port thinking that maybe some small debris was locked inside, but instead I've seen a crooked metal brace (closeup photo attached, the part was really small) that seemed loose and was blocking the connector to go fully inside. I didn't know what it was, but I used a toothpick to try to lock it in place or at least see if it's really loose, but upon touching it simply came out from the port and hit the floor.
The port now works flawlessly, it charges, it connects to the computer, nothing seems lose, the cable sits tight, and it looks perfectly normal to me. I checked some other USB-C devices I have if they have similar metal thing inside, but none does. The port now looks like all other USB-C ports I've seen.
I wouldn't expect anything to come out of the charging port in a new phone though. Would you have any idea what's the purpose of this metal brace in the Pixel's port, and what could've happened that it got detached from the port? Should I be worried or just throw it into the bin and forget?
I'd appreciate any clues and insights
Thanks!
M.
Click to expand...
Click to collapse
luisenriquereyes said:
This exact thing just happened to my Pixel 2 phone. I hope I don't have any problems. I know this is an old post. Did it ever cause you any problems?
Click to expand...
Click to collapse
No, everything was fine with the phone afterwards - at least for that reason. I had to RMA it for failing display though after few months of use, so I no longer have that particular one. With the replacement the metal brace is still intact.